ER27-520-000 · 2026-11-16 · PJM Transmission Owners (filed by PECO Energy Company and PJM)

PJM Transmission Owners file tariff revisions for service to co-located and large loads under section 205

Back to sections and commentary

PDF page 1

Suite 500 East 
1301 K Street NW 
Washington, D.C.  20005-3317 
November 16, 2026 
Honorable Debbie-Anne A. Reese 
Secretary 
Federal Energy Regulatory Commission 
888 First Street, N.E. 
Washington, D.C. 20426 
Re: 
Exelon Corporation, et al., Docket No. ER27-520-000 
Proposed Revisions to the PJM Open Access Transmission Tariff Addressing 
Transmission Service, Cost Allocation, and Cost Recovery for Large Loads 
and Co-Located Loads 
Dear Secretary Reese: 
Pursuant to section 205 of the Federal Power Act (“FPA”)1 and Part 35 of the 
Commission’s regulations,2 the PJM Transmission Owners,3 acting through the Consolidated 
Transmission Owners Agreement,4 submit for filing revisions to the PJM Interconnection, L.L.C. 
(“PJM”) Open Access Transmission Tariff (“Tariff”).5   
As discussed below, and supported by the Direct Joint Testimony of Peter Blazunas and 
Hanhan Hammer, the proposed Tariff revisions establish rates, cost allocation, cost recovery 
mechanisms, financial protections, revenue-crediting requirements, and transparency measures 
associated with transmission service to be taken by Eligible Customers6 on behalf of Co-Located 
Loads and Large Loads.7  These revisions are both responsive to and consistent with the 
preliminary findings made by the Commission in its June 18, 2026 Order Instituting Proceeding 
1
16 U.S.C. § 824d. 
2
18 C.F.R. Part 35. 
3
The PJM Transmission Owners also may be referred to herein as “Transmission Owners.” 
4  
Consolidated Transmission Owners Agreement, FERC Rate Schedule No. 42, § 7.3.  These revisions were 
approved by the PJM Transmission Owners Agreement Administrative Committee on November 12, 2026. 
5
Pursuant to Order No. 714, this filing is submitted electronically by PJM on behalf of the PJM Transmission 
Owners as part of an XML filing package conforming to the Commission’s regulations.  PJM makes this submission 
in its capacity as administrator of the Tariff and to retain administrative control over the electronic Tariff. 
Accordingly, the PJM Transmission Owners have requested that PJM submit the proposed Tariff revisions through 
the Commission’s eTariff system as part of PJM’s electronic Intra-PJM Tariff. 
6
Capitalized terms not otherwise defined herein have the meanings set forth in the Tariff, the PJM 
Transmission Owners’ proposed Tariff revisions and pro forma Cost Recovery Agreement filed herein, or in the 
proposed Tariff revisions included in PJM’s companion section 205 filing. 
7 
Direct Joint Testimony of Peter Blazunas and Hanhan Hammer, Exhibit No. PTO-0001 (“Blazunas and 
Hammer Direct Joint Testimony”).

PDF page 2

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 2 
 
 
 
 
Under Section 206 of the Federal Power Act in Docket No. EL26-67-000 (“Show Cause Order”),8 
and also comply with the Commission’s June 18, 2026 Order on Rehearing, Clarification, 
Compliance Filing and Paper Hearing in Docket Nos. EL25-49, et al. (“Co-Located Load Paper 
Hearing Order”).9  Additionally, the proposed tariff revisions have been designed to be consistent 
with PJM’s responsive section 205 filings establishing provisions for: (1) a new Fast Energization 
Process for generation interconnection and Large Load-related transmission service requests; (2) 
co-location and behind-the-meter generation; and (3) ride-through.   
 
This filing consists of several key elements.  With respect to each of these components, the 
PJM Transmission Owners have carefully considered and accounted for the need for ratepayer 
protections, Large Load and generation customer cost certainty and commercial stability, and cost 
transparency.  The PJM Transmission Owners’ proposal achieves a just and reasonable balance by 
protecting everyday customers from unfairly bearing the significant transmission-related costs 
necessary to connect and serve new Large Load and generation customers.  At the same time, it 
promotes speed-to-power, which is critical to supporting the accelerating pace of Artificial 
Intelligence, the growth of domestic manufacturing, and other information technology 
developments.  The elements are as follows: 
 
1. A pro forma Cost Recovery Agreement and related implementing Tariff provisions.  
The pro forma Cost Recovery Agreement (“CRA”) and related Tariff provisions are 
designed to address the Commission’s concerns that the Tariff lacks an adequate 
mechanism to mitigate the risk of cost shifting among transmission customers.  
Consistent with the Show Cause Order, the pro forma CRA will require Eligible 
Customers taking service on behalf of Large Load customers to make a minimum 
contribution towards transmission owners’ revenue requirements, along with a 
shortfall payment and crediting mechanism and financial security obligations, to 
ensure that each customer’s minimum commitment is satisfied over the term of the 
CRA.  The PJM Transmission Owners’ proposal also appropriately recognizes, 
consistent with the Commission’s acknowledgement,10 that voluntary cost recovery 
agreements and other ratepayer protection mechanisms have been, and continue to be, 
utilized at the retail and wholesale level by utilities within PJM.  Therefore, the PJM 
Transmission Owners’ proposal makes clear that PJM Transmission Owners may 
continue to utilize existing and  new consumer protection arrangements, as alternatives 
to the pro forma CRA, so long as those arrangements result in comparable protections 
and are accepted for filing by the Commission. 
 
 
8  
PJM Interconnection, L.L.C., 195 FERC ¶ 61,211 at PP 35, 41-101 (2026), errata notice, 196 FERC ¶ 61,122 
(2026). 
9  
PJM Interconnection, L.L.C., 195 FERC ¶ 61,209 (2026).  The PJM Transmission Owners will be 
submitting a letter in Docket Nos. EL25-49, et al. notifying the parties to that proceeding that the tariff revisions 
being submitted in this filing also satisfy the PJM Transmission Owners’ compliance obligations from the Co-
Located Load Paper Hearing Order. 
10  
Show Cause Order at P 69.

PDF page 3

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 3 
 
 
 
 
2. Rates for Transmission Services Available to Large Loads and Co-Located Loads.  
The PJM Transmission Owners’ proposal contains rates for the new services the 
Commission has required to be made available to Eligible Customers taking service 
on behalf of Co-Located Loads and that the Commission preliminarily found should 
also be extended to certain Large Loads.  These include Firm Contract Demand 
Transmission Service (“FCDS”), Non-Firm Contract Demand Transmission Service 
(“NFCDS”), and Interim Network Integration Transmission Service (“Interim NITS”).  
The rates for these services are largely identical to those proposed by the PJM 
Transmission Owners and approved by the Commission in the Co-Located Load Paper 
Hearing Order, with the modifications required by the Commission in that Order.  The 
PJM Transmission Owners have also included, consistent with the Co-Located Load 
Paper Hearing Order, financial penalties for unreserved use by Eligible Customers 
taking one of the new transmission services on behalf of Co-Located Loads or Large 
Loads.      
 
3. Cost Allocation and Recovery of Upgrades Necessary to Provide Interconnection and 
Transmission Service.  The PJM Transmission Owners are proposing a methodology 
for allocating and recovering the costs of transmission upgrades, referred to as 
Interconnection Reliability Reinforcements (“IRRs”), resulting from PJM’s proposed 
Fast Energization Process.11  The allocation methodology is based on a modified 
version of PJM’s existing proportional impact allocation methodology for customers 
in its New Service Request process.  Cost responsibility will be assigned to those 
Zones containing Large Loads being studied for transmission service in the PJM Fast 
Energization process. Those costs will be recovered through a combination of firm 
transmission service rates to customers in the Zones where the IRRs are located, along 
with a new Interconnection Reliability Reinforcement Charge assessed to Zones based 
on the calculated impact of the Large Loads within the Zones.  As it pertains to the 
proportional impact-driven share of costs attributable to Co-Located Loads and Large 
Loads, this allocation methodology will apply to each portfolio of IRRs identified 
through PJM’s Fast Energization Process for 15 years.12  After that 15-year period, the 
remaining costs of the IRRs will be subject to regional allocation using the then-current 
Schedule 12 methodology that applies to Regional Transmission Expansion Plan 
(“RTEP”) reliability projects.  The proportional impact-driven share of costs 
attributable to generators in the Fast Energization Process will be recovered through a 
fee billed and collected by PJM over a 15-year period and credited back to customers 
in the Zones that are allocated IRR costs. 
 
 
11  
PJM’s proposed Fast Energization Process is an annual process that evaluates both generator interconnection 
and Large Load transmission service requests through a single cluster study, resulting in a consolidated portfolio of 
IRRs needed to provide interconnection and transmission service to the cluster of generator and Large Load-related 
service requests. 
12  
References throughout this filing to the “portfolio” are those projects (e.g., upgrades, transmission 
reinforcements) identified by PJM that will be required to accommodate both generators seeking interconnection and 
Eligible Customers seeking transmission service on behalf of Large Loads in each study cycle.

PDF page 4

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 4 
 
 
 
 
4. Transparency and Customer Protection Commitments.  In addition to the basic cost 
allocation and rate design features of the PJM Transmission Owners’ proposal, the 
PJM Transmission Owners are committing to make, on compliance, necessary changes 
to their formula rate templates to: (1) provide transparency to state regulators and other 
interested parties regarding the costs of transmission facilities being constructed by 
each Transmission Owner to provide transmission service to Large Loads; and (2) 
adopt a mechanism designed to protect wholesale transmission customers not 
regulated at the retail level (municipals, cooperatives, and other applicable load-
serving entities) from having to bear excessive large-load-related transmission upgrade 
costs.     
 
Each of these elements is designed to align with the Fast Energization proposal being 
submitted by PJM on the same date as this filing.  Based on information provided to stakeholders,13 
PJM is proposing an approach that would process and study requests for both generator 
interconnection and transmission service on behalf of Large Loads in a single annual cluster, 
resulting in a portfolio of IRRs necessary to accommodate the aggregate of interconnection and 
transmission service requests in each cluster cycle.  Although each of the elements of the 
Transmission Owners’ proposal is designed to work in tandem with PJM’s proposed Fast 
Energization Process, the essential elements are independently just and reasonable, and 
importantly, satisfy the Commission’s preliminary findings in the Show Cause Order.  In other 
words, regardless of how the Commission acts on PJM’s filing, the Commission can and should 
determine that the key aspects of the PJM Transmission Owners’ proposal, as discussed below, 
are just and reasonable and should be accepted.  This remains the case even if certain incremental 
changes are required on compliance to ensure compatibility with the determinations the 
Commission makes regarding the planning and study process for generator interconnection and 
transmission service customers.   
 
 
 
 
 
13  
PJM Interconnection, L.L.C., Co-Located Load Order Workshop Meeting Materials, Item 02 (Nov. 11, 
2026), 
https://www.pjm.com/-/media/DotCom/committees-groups/workshops/cllsco/2026/20261112/20261112-
item-02---raa-revisions-schedule-8-november-11-draft--redline.pdf 
(RAA 
Schedule 
8 
revisions); 
https://www.pjm.com/-/media/DotCom/committees-groups/workshops/cllsco/2026/20261112/20261112-item-02---
tariff-revisions-part-i-definitions-november-11-draft---redline.pdf (Tariff, Part I revisions); https://www.pjm.com/-
/media/DotCom/committees-groups/workshops/cllsco/2026/20261112/20261112-item-02---tariff-revisions-part-iii-
nits-november-11-draft---redline.pdf (Tariff, Part III revisions); https://www.pjm.com/-/media/DotCom/committees-
groups/workshops/cllsco/2026/20261112/20261112-item-02---tariff-revisions-part-viii-november-11-draft--
redline.pdf 
(Tariff, 
Part 
VIII 
revisions); 
https://www.pjm.com/-/media/DotCom/committees-
groups/workshops/cllsco/2026/20261112/20261112-item-02---tariff-revisions-part-xi-new-transmission-services-
november-11-draft---redline.pdf (Tariff, Part XI revisions).

PDF page 5

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 5 
 
 
 
 
I. 
EXECUTIVE SUMMARY 
The proposed Tariff revisions contained in this filing establish rates, cost allocation, cost 
recovery mechanisms, financial protections, revenue-crediting requirements, and transparency 
measures associated with transmission service to be taken on behalf of Co-Located Loads and 
Large Loads.  These revisions are responsive to and consistent with both the preliminary findings 
made by the Commission in its June 18, 2026 Show Cause Order as well as the Commission’s Co-
Located Load Paper Hearing Order issued on the same date.  The proposed Tariff revisions are 
designed to work in tandem with PJM’s section 205 filing submitted on the same date, which 
proposes a Fast Energization Process that combines both generator interconnection and 
transmission service requests made on behalf of Co-Located Loads and Large Loads into a single 
annual cluster process.  The process would result in a consolidated portfolio of IRRs needed to 
provide interconnection and transmission service to the cluster of generator and Large Load-
related service requests.  However, the key elements of the PJM Transmission Owners’ proposal 
are independently just and reasonable and fully address both the Commission’s preliminary 
findings in the Show Cause Order and the policies underlying those findings.   
 
The Commission has explained that the integration of significant new Large Loads is an 
urgent challenge requiring a timely, orderly, and nondiscriminatory path to transmission service 
that preserves reliability and affordability.14  The PJM Transmission Owners’ proposal reflects the 
need for prompt action and meets the Commission’s objective to provide ratepayer protections, as 
identified in the Show Cause Order.  The PJM Transmission Owners’ proposed revisions therefore 
strike a practical balance.  Namely, they provide sufficient terms to ensure that Large Loads and 
other responsible entities bear their share of the costs and revenue risks associated with their 
requests, thereby protecting other customers, without imposing unnecessary complexity or 
unpredictability that could jeopardize speed to power by impeding efficient planning. 
Consistent with the Commission’s findings that it was not seeking to alter or call into 
question existing cost allocation methods for transmission upgrades,15 existing zonal NITS and 
formula rate structures remain the starting point for recovering applicable transmission revenue 
requirements, including transmission upgrades necessary to facilitate transmission service 
requested by Eligible Customers on behalf of Large Loads.  The PJM Transmission Owners’ 
proposed Tariff revisions supplement those structures with measures addressing distinct risks 
associated with Large Load integration, including secured commitments associated with the 
requested transmission service, potential shortfalls in or loss of anticipated firm service revenues, 
unreserved transmission use, and potential double recovery.  For instance, and as explained further 
herein, the PJM Transmission Owners’ proposal includes: 
1. An obligation on Large Loads to enter into a pro forma CRA, or comparable alternative 
agreement, to ensure the Large Load Customer’s committed contribution toward the 
applicable Transmission Owner’s transmission revenue requirement and to require the 
Large Load Customer to provide Credit Support securing the associated payment 
 
14  
Show Cause Order at PP 1-7, 35-39. 
15  
Id. at P 81.

PDF page 6

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 6 
 
 
 
 
obligations.  The pro forma CRA includes applicable shortfall and termination 
payments to reduce the revenue requirement that would otherwise need to be recovered 
from other transmission customers if the Large Load fails to take the committed level 
of transmission service, along with requirements to provide and maintain robust 
financial security.  The PJM Transmission Owners propose to require Large Loads to 
enter into CRAs, or comparable agreements prior to entering PJM’s Fast Energization 
Process to ensure a significant financial commitment on the part of the Large Load 
Customer and thereby deter speculative or duplicative transmission service requests.  
Any amounts collected from the Large Load Customer as a result of terminating the 
CRA prior to the commencement of service will first go towards defraying any costs 
associated with transmission development that is no longer needed, with any remaining 
amounts credited against the Transmission Owner’s revenue requirement.  Any 
termination amount collected from the Large Load Customer after service commences 
will be entirely credited against the Transmission Owner’s revenue requirement, solely 
to the benefit of other customers.  These mechanisms mitigate the risks of potential cost 
shifts to other transmission customers.    
2. A methodology to allocate the costs of the portfolio of transmission upgrades, known 
as Interconnection Reliability Reinforcements, identified by PJM in its Fast 
Energization Process as needed to accommodate the generator interconnection and 
transmission service requests in each annual cycle.  This methodology will allocate cost 
responsibility among PJM Zones – and only those zones with Large Loads studied 
within an annual cycle – in a manner roughly commensurate with benefits by utilizing 
modeled electrical impacts on identified constraints.  This approach is consistent with 
the proportional impact methodology approved by the Commission and currently used 
by PJM to allocate costs associated with its current generator interconnection process.  
This methodology will also determine the proportional impact associated with 
generators seeking interconnection through the Fast Energization Process annual cycle, 
which will be recovered through a fee assessed over a 15-year period.  The PJM 
Transmission Owners are also proposing that all IRRs be allocated to Zones containing 
Large Load-related transmission requests for 15 years, after which point the remaining 
costs will be allocated using the then-current general regional cost allocation 
methodology.  This approach balances a recognition of the initial Large Load-related 
drivers of IRRs, with the fact that changes in system conditions, use and topology will 
result in a broader set of beneficiaries over time. 
 
3. A commitment to include in their transmission owner-specific formula rates, on 
compliance, additional measures to protect municipal utilities, cooperatives, and other 
direct wholesale customers from bearing an excessive share of Large Load-related 
zonal costs.  The PJM Transmission Owners are also committing to include in their 
formula rates cost information regarding transmission upgrades needed to provide 
service to Large Loads.  This information will address both the transparency concerns 
identified by the Commission in the Show Cause Order, as well as provide state 
authorities with information relevant to any further allocation of those costs at the retail 
level.

PDF page 7

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 7 
 
 
 
 
 
4. Extending the rate design elements associated with the new transmission services 
required by the Commission in the Co-Located Load Paper Hearing Order to 
encompass the ability of Large Loads to take these new transmission services, which 
the PJM Transmission Owners understand PJM will be proposing in its own section 
205 filing.  The rate design also includes appropriate crediting provisions for the new 
transmission services required by the Commission to ensure that non-firm transmission 
revenues are used to offset rates paid by firm transmission customers.  Moreover, the 
PJM Transmission Owners’ proposal includes financial penalties for unreserved use of 
the transmission system that will apply to transmission service being taken on behalf 
of both Co-Located Load and Large Loads.  These penalties will work in coordination 
with PJM’s operational consequences both to ensure the reliable operation of the 
system and protect other transmission ratepayers from unfairly subsidizing customers 
that fail to abide by their contractual limits.   
 
II. 
BACKGROUND 
A. 
PJM Transmission Owner Filing Rights 
As the Commission has noted, the PJM Transmission Owners have exclusive and unilateral 
rights regarding the cost allocation provisions of Schedule 12 of the Tariff.16  The PJM 
Transmission Owners relied on those same authorities in their February 23, 2026 paper hearing 
brief in explaining their rights and obligations under the Consolidated Transmission Owners 
Agreement to develop and file the rates for the new transmission services that the Commission has 
required for Co-Located and Large Loads.17  The Show Cause Order recognized the PJM 
Transmission Owners may submit this filing proposing revisions to the Tariff pursuant to their 
applicable FPA section 205 filing rights.18  
B. 
Procedural Background 
1. 
Co-Located Load Orders and Remaining Compliance Obligations. 
On February 20, 2025, the Commission instituted a proceeding under section 206 of the 
FPA based on its preliminary concern that the Tariff did not address with sufficient clarity or 
consistency the rates, terms, and conditions applicable to co-location arrangements.19  
 
16  
See Neptune Regional Transmission System, LLC and Long Island Power Auth. v. PJM Interconnection, 
L.L.C., 175 FERC ¶ 61,247 at P 47 (2021), and PPL Electric Utils. Corp., 177 FERC ¶ 61,123 at PP 34, 36 (2021); 
see also Tariff, Part I, Section 9.1(a). 
17  
See Initial Brief and Joint Responses of the Indicated PJM Transmission Owners to Paper Hearing Questions 
at 3 & nn.7-9, Docket Nos. EL25-49, et al. (filed Feb. 23, 2026) (“PJM Transmission Owners Initial Paper Hearing 
Brief”). 
18  
See Show Cause Order at P 38. 
19  
PJM Interconnection, L.L.C., 190 FERC ¶ 61,115 at PP 1-5 (2025).

PDF page 8

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 8 
 
 
 
 
On December 18, 2025, the Commission found the Tariff to be unjust and unreasonable 
and established a framework under which an Eligible Customer taking transmission service on 
behalf of Co-Located Load must take: (1) NITS, including interim non-firm service pending 
completion of the Network Upgrades required for permanent NITS; (2) FCDS; or (3) NFCDS.  
The Commission also established a paper hearing to determine the just and reasonable rates, terms, 
and conditions for those services.20 
The PJM Transmission Owners submitted an initial brief on February 23, 2026, a response 
to PJM’s initial brief on March 25, 2026, and a reply brief on April 24, 2026, addressing the rates 
and related measures applicable to the new services.21  On June 18, 2026, the Commission resolved 
the paper hearing issues and directed further compliance filings by PJM and the PJM Transmission 
Owners.  Among other matters, the Commission addressed the rate treatment for FCDS, NFCDS, 
and Interim NITS and the imposition of financial penalties for unreserved transmission use.22  
Notably, the Commission accepted the PJM Transmission Owners’ proposals with respect to the 
rates for FCDS and Interim NITS, as well as financial penalties for unreserved use.  The 
Commission, however, required the PJM Transmission Owners to adopt a lower minimum rate or 
discount for NFCDS below the Firm Contract Demand rate.   
On August 17, 2026, PJM and the PJM Transmission Owners submitted partial compliance 
filings implementing Interim NITS.23  The PJM Transmission Owners’ filing established the 
Interim NITS rate and made related conforming Tariff revisions.24  The present filing implements 
the PJM Transmission Owners’ remaining compliance obligations associated with the Co-Located 
Load Paper Hearing Order and makes the revisions to the August 17, 2026 filing required to 
integrate the remaining new services and their application to eligible Large Loads.25 
 
 
 
20  
PJM Interconnection, L.L.C., 193 FERC ¶ 61,217 at PP 2, 160, 193-220 (2025) (“December 18 Show Cause 
Order”). 
21  
PJM Transmission Owners Initial Paper Hearing Brief; Joint Response of the Indicated PJM Transmission 
Owners, Docket Nos. EL25-49, et al. (filed Mar. 25, 2026); PJM Transmission Owners Reply Brief, Docket Nos. 
EL25-49, et al. (filed Apr. 24, 2026) (“PJM Transmission Owners Reply Brief”). 
22  
Co-Located Load Paper Hearing Order at PP 398-412, 517, 529. 
23  
PJM Transmission Owners Partial Compliance Filing, Docket No. ER26-3537-000 (filed Aug. 17, 2026) 
(“PJM Transmission Owners August 17 Compliance Filing” or “August 17 Compliance Filing”); PJM Compliance 
Filing, Docket No. ER26-1479-002 (filed Aug. 17, 2026) (“PJM August 17 Compliance Filing”). 
24  
Because PJM’s companion filing modifies the effective date of certain Tariff provisions that were included 
in PJM’s August 17 Compliance Filing, the PJM Transmission Owners intend to withdraw their August 17 
Compliance Filing.  Accordingly, the PJM Transmission Owners are including in this section 205 filing the 
corresponding Tariff revisions previously submitted with the August 17 Compliance Filing, except for the definition 
of “Co-Located Gross Demand,” which is no longer necessary. 
25  
See infra Section II.B.1 and 2.

PDF page 9

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 9 
 
 
 
 
2. 
Large Load Show Cause Order and Section 205 Proposal. 
On June 18, 2026, the Commission instituted a separate section 206 proceeding concerning 
the integration of Large Loads in PJM. The Commission preliminarily identified concerns 
regarding: 
1. The application, study, and continuing operational requirements applicable to Eligible 
Customers seeking transmission service on behalf of Large Loads; 
2. Transparency concerning the Network Upgrade costs associated with that service, a 
pro forma CRA to mitigate cost shifting risks, and a mechanism to ensure CRA 
payments are credited toward the revenue requirement consistent with the 
Commission’s cost-of-service regulations; 
3. Transmission-service options for flexible Large Loads; and 
4. The rates, terms, and conditions applicable to generation serving electrically proximate 
Large Load or Co-Located Load.26 
3. 
Abeyance Request. 
The Commission expressly contemplated that PJM and the PJM Transmission Owners 
could address some or all of the concerns identified in the Show Cause Order through affirmative 
section 205 filings covering matters within their respective filing rights.27  On August 14, 2026, 
the Commission granted the PJM Transmission Owners’ requested abeyance to permit the PJM 
Transmission Owners to develop one or more section 205 filings.28  The Commission explained 
that the anticipated PJM Transmission Owner filings would address matters including rates for the 
new transmission services, pro forma CRAs, and financial penalties.  It also provided that a 
respondent’s submission of a section 205 filing by November 16, 2026, would suspend that 
respondent’s obligation to answer the Show Cause Order pending further Commission action.29  
The PJM Transmission Owners submit the present filing following that section 205 path.  
The proposed Tariff revisions address the Commission’s preliminary findings, and the PJM 
Transmission Owners therefore request that the Commission accept the revisions under section 
205 and, as appropriate, resolve, terminate, or continue to hold in abeyance the corresponding 
aspects of the pending section 206 proceeding.  Specifically, the pro forma CRA, the application 
of the new transmission-service rates and financial penalties to eligible Large Loads, and the 
proposed transparency and customer protection measures address the Show Cause Order’s 
preliminary findings within the PJM Transmission Owners’ applicable rate design and cost 
allocation filing rights.  The filing also establishes the cost allocation and cost recovery treatment 
 
26  
Show Cause Order at PP 35, 41-101. 
27  
Id. at PP 38-39. 
28  
PJM Interconnection, L.L.C., 196 FERC ¶ 61,129 at P 9 (2026). 
29  
Id. at PP 5, 10.

PDF page 10

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 10 
 
 
 
 
for the portfolio of transmission reinforcements identified through PJM’s separately proposed Fast 
Energization Process. 
III. 
DISCUSSION 
A. 
Pro Forma Cost Recovery Agreement and Related Tariff Provisions 
 
The PJM Transmission Owners’ proposed pro forma CRA addresses the Show Cause 
Order’s preliminary findings that the PJM tariff should include an agreement requiring a minimum 
contribution towards a transmission owner’s revenue requirement to protect against cost shifting 
if a Large Load does not go into service or ends up taking less transmission service than 
anticipated.30  As further detailed in the Blazunas and Hammer Direct Joint Testimony and below, 
the pro forma CRA accomplishes this through imposing on Large Load Customers a financially 
secured minimum transmission-revenue contribution commitment associated with the amount of 
firm transmission service requested from PJM on behalf of a Large Load.31  The CRA is executed 
after completion of the applicable Transmission Owner’s retail interconnection study process and 
before the Eligible Customer proceeds through PJM’s applicable transmission-service process. 
The Large Load Customer must identify and reflect in the CRA its: (i) anticipated load demand, 
(ii) proposed schedule for ramping up such demand, if any, and (iii) anticipated dates for each 
stage of service.  Together with the corresponding amount and type of firm transmission service 
that an Eligible Customer intends to request on the Large Load Customer’s behalf, this information 
forms the Large Load’s initial financial commitment and credit support obligations while the 
customer’s transmission service request is processed and studied by PJM. 
Following completion of PJM’s transmission study and service process, the CRA will be 
updated to reflect any necessary modifications to the load ramp and the dates on which each 
scheduled level of service will become effective, based on the outcome of the PJM study process. 
The resulting information determines the Large Load’s “Firm Load Commitment,” which serves 
as the benchmark for the CRA’s ongoing financial protections.  No less than annually, beginning 
when the Large Load takes service, the applicable Transmission Owner will calculate the 
minimum transmission-revenue contribution associated with the Firm Load Commitment, referred 
to as the Committed Revenue Contribution.  The Transmission Owner will compare that amount 
with qualifying revenues attributable to firm transmission service actually taken to serve the Large 
Load, referred to as the Actual Revenue Contribution.  If the Actual Revenue Contribution is less 
than the Committed Revenue Contribution for such a period (referred to as a “Measurement 
Period”) the Large Load Customer pays only the difference, referred to as the Shortfall Amount. 
Credit support secures the Large Load Customer’s obligations to pay any Shortfall Amount, and 
the CRA’s early- and partial-termination provisions protect the applicable portion of the remaining 
 
30  
Show Cause Order at PP 80-81.  
31  
Blazunas and Hammer Direct Joint Testimony at 32-37.

PDF page 11

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 11 
 
 
 
 
projected revenue contribution if the transmission request or commitment is withdrawn, or the 
Large Load is abandoned or terminated, or its capacity is permanently reduced. 
1. 
The Pro Forma Cost Recovery Agreement and Related Tariff 
Provisions Balance the Timely Integration of Large Loads With 
Protection Against Cost Shifting. 
The Commission preliminarily found that the Tariff may be unjust and unreasonable 
because it lacks adequate mechanisms to mitigate the risk of cost shifting when transmission 
facilities are developed to serve a Large Load that does not materialize or ultimately takes less 
transmission service than anticipated.32  In those circumstances, anticipated transmission revenues 
may not be realized, leaving other transmission customers to bear a greater share of the applicable 
transmission costs.  The Commission, therefore, preliminarily found that the Tariff should include 
a pro forma CRA requiring a minimum contribution toward the relevant Transmission Owner’s 
transmission revenue requirement.33 
The Commission identified several features  such a agreements should contain.34  The 
minimum contribution should be based on the level of jurisdictional transmission service, 
measured in MW, requested on behalf of the Large Load.35  The agreement should also include 
Credit Support or other financial security sufficient to secure the required payment obligations.36  
Payments made under the agreement should be credited toward the applicable Transmission 
Owner’s transmission revenue requirement in accordance with the Commission’s cost-of-service 
regulations, with their formula rate treatment identified in an appropriate workpaper.37 
The Transmission Owners’ proposed CRA adopts those core elements and incorporates 
them into an integrated mechanism that operates over the term of the agreement, which will be a 
minimum of ten years, with the specific term to be negotiated between the applicable Transmission 
Owner and counterparties.   
The proposal, which includes both minimum revenue contribution and financial security 
assurances, while providing flexibility to tailor certain aspects of the CRA to the individual 
Transmission Owner and customer parties, is intended to provide necessary ratepayer protections 
while promoting timely Large Load integration.  The PJM Transmission Owners recognize the 
need to facilitate speed-to-power for Large Load growth, particularly data centers and other 
computational loads driving AI advances and other key technologies.  They have therefore 
established a CRA framework under which projects can advance while their final service quantities 
and timing are determined through the applicable study and service processes.  At the same time, 
 
32  
Show Cause Order at PP 77-81. 
33  
Id. at P 81. 
34  
Id. at PP 82-84. 
35  
Id. at P 83. 
36  
Id. 
37  
Id. at P 84.

PDF page 12

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 12 
 
 
 
 
as the Commission pointed out, existing transmission customers should not be required to absorb 
the revenue consequences of speculative or insufficiently developed projects.  Such projects may  
prompt study, planning, engineering, procurement, or construction activity but do not proceed as 
represented.38 
The CRA balances those interests by requiring a Large Load Customer to make a 
meaningful, financially-secured commitment after completing the applicable Transmission 
Owner’s retail interconnection study process and before proceeding through PJM’s Fast 
Energization Process.  That requirement helps distinguish projects prepared to proceed from less-
developed requests before additional PJM and Transmission Owner resources are devoted to them.  
This approach recognizes and addresses the Commission’s concern that speculative or duplicative 
requests may delay the study process, distort forecasts, result in unnecessary transmission buildout, 
and shift costs when the anticipated load does not materialize. The Commission identified 
meaningful milestones and financial commitments as potential readiness measures that can help 
ensure that Large Load-related transmissions service requests are more viable and more likely to 
proceed as planned.39  The CRA incorporates both measures by tying the Large Load Customer’s 
commitment to defined project milestones and corresponding financial obligations. 
The pro forma CRA included with this filing will not be the exclusive or presumptive 
vehicle for protecting against cost shifting among customers.  Under the PJM Transmission 
Owners’ proposal, Transmission Owners will be permitted to choose between utilizing the pro 
forma CRA or entering into a separate agreement.  Any such separate  agreement, in conjunction 
with applicable federal and state regulatory requirements, must result in minimum transmission 
service and credit standards, or comparable protections, as determined by the Commission.40  This 
flexibility is a key aspect of, and is not severable from, the PJM Transmission Owners’ pro forma 
CRA proposal.  As discussed further below, the PJM Transmission Owners’ proposal also provides 
transparency to state regulators and other interested parties regarding the costs of transmission 
facilities being constructed by the Transmission Owner to provide transmission service on behalf 
of Large Loads.  This transparency will provide state commissions and other retail regulators 
access to information to assist them in allocating some amount of transmission rate costs 
specifically to Large Load classes of customers within their jurisdictions, if desired.  Several PJM 
Transmission Owners also have existing Large Load cost-recovery or ratepayer-protection 
mechanisms already approved by their respective state commissions.  These provisions 
appropriately recognize, as the Commission acknowledged in the Show Cause Order,41 that cost 
recovery agreements and other ratepayer protection mechanisms have been, and continue to be, 
 
38  
Id. at P 81.  
39  
Id. at PP 56-57, 59. 
40  
Proposed Tariff, Part VIII, Subpart N, section 441(a)(ii). 
41  
Show Cause Order at P 69.

PDF page 13

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 13 
 
 
 
 
utilized at the retail and wholesale levels by utilities within PJM to provide commensurate 
protections against shifting costs to other customers.42  
2. 
The CRA Assigns Distinct Responsibilities to the Transmission Owner, 
Large Load Customer, and Eligible Customer. 
The Commission’s preliminary finding contemplated a pro forma CRA among PJM, the 
relevant Transmission Owner, and the Eligible Customer taking transmission service on behalf of 
the Large Load, with the Eligible Customer responsible for the minimum contribution and 
associated financial security.43  However, the Commission also acknowledged in the Show Cause 
Order that Transmission Owners have filed agreements under which minimum contributions to 
Commission-jurisdictional transmission revenue requirements are guaranteed directly by Large 
Load Customers, rather than by an Eligible Customer taking transmission service on the Large 
Load Customer’s behalf.44  In order to best account for each entity’s distinct roles in PJM and align 
financial responsibility with control over the risk addressed by the pro forma CRA, the CRA 
proposed herein is structured as a three-party agreement between the applicable Transmission 
Owner, the underlying Large Load (referred to in the CRA as the “Large Load Customer”), and 
the Eligible Customer taking service on behalf of the Large Load Customer.45 
The CRA assigns each Party the obligations corresponding to its role.  The Large Load 
Customer owns, operates, leases, or otherwise controls the Large Load Facilities and therefore 
bears the CRA’s payment and Credit Support obligations.  Those obligations include: (i) providing 
and maintaining Credit Support;46 (ii) paying any Shortfall Amount, Early Termination Amount, 
or Partial Termination Amount;47 (iii) supplying information concerning the Large Load Facilities 
and project status;48 and (iv) remaining responsible for those obligations regardless of a dispute 
with the Eligible Customer.49  The Eligible Customer remains the transmission customer. It 
requests and takes Firm Transmission Service50 under the Tariff on behalf of the Large Load 
Customer, pursues the applicable PJM process, and provides or authorizes access to the service, 
billing, settlement, and allocation information necessary to calculate and verify amounts under the 
CRA.51  The Eligible Customer is not responsible for the Large Load Customer’s payment or 
 
42  
Several Transmission Owners in PJM have processes already established and approved by their state 
commissions.   
43  
Show Cause Order at PP 77, 80-83. 
44  
Id. at P 82. 
45  
Proposed Tariff, Part VIII, Subpart N, section 441(a)(i). 
46  
Proposed pro forma CRA, Part IX, Subpart P at Article 6.  
47  
Id. at Article 5.3, 9. 
48  
Id. at Articles 5.6, 13.3, 14.1. 
49  
Id. at Article 15. 
50  
“Firm Transmission Service” is a new proposed definition that encompasses Network Integration 
Transmission Service, Firm Point-to-Point Transmission Service, and Firm Contract Demand Transmission Service. 
51  
Proposed pro forma CRA, Part IX, Subpart P at Article 5.6.

PDF page 14

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 14 
 
 
 
 
Credit Support obligations.  The Transmission Owner calculates the Committed Revenue 
Contribution, Actual Revenue Contribution, Shortfall Amount, Credit Support Requirement, and 
any applicable termination amount; issues invoices; receives and administers Credit Support; 
performs required reconciliations; and accounts for and credits collected amounts through its 
applicable Commission-jurisdictional rate.  The Eligible Customer is responsible for information-
sharing and administrative functions necessary to implement the CRA, such as providing the 
Transmission Owner billing, settlement, load and allocation information needed to identify 
transmission rate revenues associated with the Large Load Customer.52 
PJM is not a party to the CRA and does not hold or administer CRA Credit Support.  The 
CRA supplements the underlying transmission-service arrangements but does not itself authorize 
transmission service, determine the amount of service available, or independently require 
construction of transmission facilities.  Those matters remain governed by the Tariff, PJM’s study 
and service processes, the applicable transmission-service agreement, and other relevant 
agreements. 
The proposed pro forma CRA’s assignment of direct payment and Credit Support 
obligations to the Large Load Customer, rather than the Eligible Customer, and its exclusion of 
PJM as a contractual counterparty are just and reasonable and consistent with the cooperative 
jurisdictional responsibilities of the Commission and the states contemplated by the FPA.  This 
allocation of obligations more closely aligns financial responsibility with control over the risk 
addressed by the CRA.  The anticipated transmission revenue contribution depends principally on 
whether the Large Load project proceeds, achieves the required readiness, begins taking service at 
the committed level, and continues operating during the CRA term.  The Large Load Customer, 
as the entity that owns, operates, leases, or otherwise controls the Large Load Facilities, is best 
positioned to control those related decisions and circumstances.  The Eligible Customer, by 
contrast, may be an intermediary or unaffiliated load-serving entity that requests and takes 
transmission service on the Large Load Customer’s behalf but does not control the Large Load 
Customer’s construction, financing, readiness, demand, or ongoing operation.   
Requiring the Eligible Customer to secure the Large Load Customer’s revenue 
commitment could therefore place the financial exposure on an entity that does not control whether 
the underlying Large Load Customer develops and operates its project as represented and, at a 
minimum, would require in many cases the implementation and administration of duplicative and 
overlapping financial obligations.  For instance, if the Eligible Customer is an electric distribution 
company, it would need to have in place and maintain appropriate additional agreements to ensure 
that any obligations imposed on it would be assigned to the relevant Large Load, and impose 
adequate security to cover those subsidiary obligations.  This structure could be extremely costly 
(costs that would ultimately be borne by all ratepayers) and, burdensome to administer, particularly 
for those companies acting as Eligible Customers on behalf of multiple Large Loads.  The proposed 
pro forma CRA instead gives the Transmission Owner direct recourse to the real party in interest, 
namely, the load entity whose interconnection drives the need for the protections underlying the 
 
52  
Id. at Article 5.6.

PDF page 15

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 15 
 
 
 
 
CRA, while preserving the Eligible Customer’s responsibility for the transmission-service, 
information-sharing, and administrative functions necessary to implement the arrangement. 
This structure is consistent with and respects the jurisdictional boundaries between the 
Commission and state regulators.  The CRA does not eliminate or diminish the requirement that 
transmission service be taken by an Eligible Customer, or otherwise serve to grant, provide or 
otherwise convey transmission service under the Tariff.53  Nor does it establish or govern any 
terms and conditions of retail service.  Rather, the CRA provides a payment and credit support 
mechanism to ensure that the Large Load Customer’s committed transmission-revenue 
contribution is satisfied.  It is the Large Load Customer whose decision to develop and operate the 
Large Load drives the need for the FERC-jurisdictional transmission service requested on its 
behalf, and whose commitments inform the amount of service and associated costs.  It is therefore 
appropriate, and jurisdictionally sound, to place the financial risks addressed by the CRA on the 
Large Load directly.  
This approach accords with the Show Cause Order and Commission precedent.  As noted 
above, the Commission recognized existing agreements under which Large Load Customers 
directly guarantee minimum contributions to Transmission Owners’ Commission-jurisdictional 
transmission revenue requirements.  It requested briefing on whether those agreements could 
satisfy the contemplated CRA requirement where they provide comparable or greater protection, 
including by avoiding duplicative Credit Support and transaction costs.54  The Commission has 
likewise accepted Commission-jurisdictional agreements under which individual Large Load 
Customers directly assumed financial commitments associated with anticipated transmission 
revenues, even though those customers did not themselves take transmission service under the 
Tariff.55   
3. 
The CRA Establishes and Maintains the Service Commitment on 
Which its Financial Protections are Based. 
The CRA identifies the Large Load Customer’s anticipated load demand, proposed load 
ramp, and anticipated timing for each stage of service, upon which the Large Load Customer’s 
financial commitment will be based.56  As part of each Transmission Owner’s or affiliate’s retail 
load interconnection process, the Large Load customer will identify the amount of load it 
anticipates adding to the system along with any ramping schedule for bringing that load online 
over a defined period.  Following completion of the applicable Transmission Owner’s load 
interconnection study process, the Parties execute the CRA based on the amount of transmission 
service that the Eligible Customer will request from PJM on behalf of the Large Load Customer 
in order to accommodate its anticipated demand, including any associated ramping schedule.  
Exhibit A to the CRA records that preliminary information, together with the corresponding 
 
53  
Id. at Article 11.3. 
54  
Show Cause Order at P 82. 
55  
See, e.g., Commonwealth Edison Co., 194 FERC ¶ 61,109 (2026); Commonwealth Edison Co., 194 FERC ¶ 
61,183 (2026). 
56  
Proposed pro forma CRA, Part IX, Subpart P at Article 3.1.

PDF page 16

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 16 
 
 
 
 
amount and type of Firm Transmission Service that the Eligible Customer intends to request on 
the Large Load Customer’s behalf (the “Initial Load Commitment”), the dates upon which service 
is estimated to begin, and any expected ramp to the project’s full requested load.57  The Initial 
Load Commitment is backed by Credit Support while the PJM transmission service study process 
is pending.  
Execution of the CRA and provision of the required Credit Support are conditions to 
proceeding through the applicable PJM process.58  This financial commitment provides assurance 
that the project is real, deters speculative requests, and protects other transmission customers if the 
Eligible Customer, on behalf of the Large Load Customer, withdraws or abandons the request, the 
Large Load Customer elects to reduce the amount requested, or the Eligible Customer refuses to 
execute the resulting Final PJM Agreement. 
Following completion of the PJM process, the Eligible Customer enters into the Final PJM 
Agreement, which identifies the Firm Transmission Service to be taken on behalf of the Large 
Load Customer.  The Transmission Owner will then update the CRA to reflect the outcome of the 
PJM process.59  If the Final PJM Agreement determines that Firm Transmission Service will not 
be available in order to accommodate a Large Load’s load ramp schedule as reflected in the Initial 
Load Commitment, because necessary IRRs will not be in service at the required times, the CRA 
will be updated accordingly.  The resulting new schedule for bringing the Large Load’s load online 
becomes the “Firm Load Commitment.”  A change to the timing or interim levels of the load ramp 
based on PJM’s determination of when the requested Firm Transmission Service can feasibly be 
provided does not trigger any financial liability for the Large Load Customer.60  By contrast, if the 
Large Load Customer elects to reduce the final amount of Firm Transmission Service requested 
on its behalf during the PJM process (e.g., by reducing the overall size of its facility), that 
customer-elected reduction is subject to the CRA’s partial-termination provisions and payment by 
the Large Load Customer of a portion of the expected revenues associated with the Firm 
Transmission Service that would have been taken to serve its full originally committed load 
amount (the “Partial Termination Amount”).61   
This approach balances the interests of the Large Load Customer and transmission 
customers.  The Large Load Customer is not charged a termination amount merely because PJM 
determines that the requested schedule for obtaining firm transmission service based on its planned 
load ramp is not feasible given the necessary IRRs and their anticipated in-service dates.  At the 
same time, if the Eligible Customer, on behalf of the Large Load Customer, withdraws or abandons 
the Firm Transmission Service request during the PJM process, or refuses to execute the resulting 
Final PJM Agreement, the withdrawal, abandonment, or refusal constitutes an early termination 
 
57  
Id. at Article 3.1. 
58  
Proposed Tariff, Part VIII, Subpart N, section 441(d).  
59  
Proposed pro forma CRA, Part IX, Subpart P at Article 3.2. 
60  
Id. at Article 3.2. 
61  
Id. at Article 9.

PDF page 17

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 17 
 
 
 
 
and requires the Large Load Customer to pay the applicable Early Termination Amount.62  A 
customer-elected reduction in the amount requested constitutes a partial termination and requires 
payment of the applicable Partial Termination Amount.63  This appropriately requires the Large 
Load Customer to make a tangible financial commitment as part of its completion of the 
Transmission Owner’s retail interconnection process, and before entering the PJM process.  Doing 
so discourages speculative and potentially duplicative study requests that would clog the PJM 
process.  It also promotes the efficient use of PJM and Transmission Owner study and planning 
resources by requiring the Large Load Customer to assume the financial consequences of 
withdrawing, abandoning, or voluntarily reducing the request after those processes have begun.  
To be clear, the CRA does not assign the Large Load Customer the costs of particular IRRs 
or a project-specific share of the IRR portfolio. The CRA and Schedule 12, which as discussed 
below establishes the cost allocation for IRRs, serve distinct functions: Schedule 12 governs the 
allocation and recovery of the revenue requirements associated with IRRs, while the CRA 
establishes the minimum Firm Transmission Service-related revenue contribution associated with 
the Large Load Customer’s commitment.64 
4. 
Credit Support Gives Financial Substance to the Large Load 
Customer’s Commitment. 
As discussed above, the proposed pro forma CRA commits the Large Load Customer to a 
transmission-revenue contribution and related payment obligations based on the level of 
transmission service.  To ensure that obligation, the Commission identified credit support as an 
important component of the contemplated cost recovery agreement.65  To implement that 
requirement, the CRA requires the Large Load Customer to provide Credit Support shortly after 
the Parties execute the agreement.66  Under proposed Tariff, Part VIII, Subpart N, section 441, 
execution of a CRA, or a qualifying alternative agreement, and provision of the required security 
are conditions to proceeding through the applicable PJM Fast Energization Cycle and obtaining 
Firm Transmission Service.67 
This sequencing gives financial weight to the Large Load Customer’s preliminary 
commitment before additional studies are performed by PJM and development activity occurs.  
 
62  
Blazunas and Hammer Direct Joint Testimony at 39-40. 
63  
See infra Section III.A.5 below, which discusses the parameters of partial and early termination, and the 
associated financial consequences to a Large Load Customer based on when and the circumstances under which it 
terminates the CRA.  See also Blazunas and Hammer Direct Joint Testimony at 39-40. 
64  
As discussed below, the PJM Transmission Owners are committing to provide cost information regarding 
IRRs in their formula rate templates which will: (1) allow PJM to allocate and invoice the charge to recover the costs 
of IRRs, (2) assist in satisfying the Commission’s findings in the Show Cause Order regarding enhanced transparency, 
and (3) assist state commissions and other retail regulators if they choose to allocate the costs of IRRs recovered 
through transmission rates to Large Load customers at the retail level. 
65  
Show Cause Order at P 83. 
66  
Blazunas and Hammer Direct Joint Testimony at 37. 
67  
Proposed Tariff, Part VIII, Subpart N, section 441(a).

PDF page 18

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 18 
 
 
 
 
The CRA helps cement those Large Load Customers that are prepared to assume the financial 
consequences of their requested service, while giving customers advance notice through the pro 
forma CRA of the obligations required to proceed.  The initial Credit Support Requirement is based 
on the service amount and timing reflected in the CRA at execution.  More specifically, the Initial 
Credit Support Requirement equals the aggregate projected charges associated with 100 percent 
of the Initial Load Commitment over the CRA term.68  Following execution of the Final PJM 
Agreement, the Transmission Owner recalculates the requirement using 100 percent of the 
projected charges associated with the updated Firm Load Commitment and remaining Service 
Dates.69   
As discussed in the Blazunas and Hammer Direct Joint Testimony, over the term of the 
CRA, the Large Load Customer’s credit support requirement is adjusted to reflect its obligations 
as those remaining obligations evolve.70  As each Measurement Period is completed, the revenues 
attributable to service for the Large Load Customer and any resulting Shortfall Amount are 
determined.71  Once the Large Load Customer has satisfied the obligations for that period, the 
amounts of those obligations are subtracted from the Credit Support calculation.72  The secured 
amount therefore declines as the underlying exposure is resolved rather than remaining fixed at its 
initial level throughout the CRA term.  Projected future transmission-service revenues do not 
reduce Credit Support before those revenues are realized.  The Credit Support protects against the 
failure of those anticipated revenues to materialize, which would be detrimental to other customers.  
The Credit Support remains as collateral unless and until it is applied to an amount actually due.  
A draw made only to preserve the value of an expiring or nonconforming letter of credit does not 
itself constitute payment or revenue.  A draw for nonpayment is limited to the amount due and 
unpaid.73   
5. 
Early and Partial Termination Payments Protect the Commitment if 
the Project Exits or the Firm Load Commitment is Reduced. 
As further discussed in the Blazunas and Hammer Direct Joint Testimony, Credit Support 
secures the Large Load Customer’s obligations, including amounts payable if the project 
terminates or the Large Load Customer elects to reduce permanently the amount of Firm 
Transmission Service requested on its behalf or, after execution of the Final PJM Agreement, the 
Firm Load Commitment before the end of the CRA term.74  Before execution of the Final PJM 
Agreement, withdrawal or abandonment of the Firm Transmission Service request, refusal to 
 
68  
See proposed pro forma CRA, Part IX, Subpart P at Exhibit C; see also Blazunas and Hammer Direct Joint 
Testimony at 37. 
69  
See proposed pro forma CRA, Part IX, Subpart P at Exhibit C; see also Blazunas and Hammer Direct Joint 
Testimony at 37. 
70  
Blazunas and Hammer Direct Joint Testimony at 38-39. 
71  
Proposed pro forma CRA, Part IX, Subpart P at Article 5. 
72  
Blazunas and Hammer Direct Joint Testimony at 37-39. 
73  
Proposed pro forma CRA, Part IX, Subpart P at Article 6.6. 
74  
Id. at Article 9 and Exhibit D; Blazunas and Hammer Direct Joint Testimony at 39-40.

PDF page 19

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 19 
 
 
 
 
execute the resulting agreement, or a reduction in the requested service may trigger an Early 
Termination Amount or Partial Termination Amount.75   
After execution of the Final PJM Agreement, voluntary termination, permanent reduction 
of the Firm Load Commitment, abandonment or cessation of the project, specified readiness 
failures, or an uncured default may trigger the corresponding payment obligation.76  A 
modification to the timing or interim levels of the load ramp resulting from PJM’s determination 
of when the requested Firm Transmission Service can feasibly be provided does not constitute a 
Partial Termination.  Failure to achieve the readiness necessary to take the applicable Firm 
Transmission Service within the period specified in the CRA may constitute a Partial Termination 
or, following the initial Service Date, support termination based on project abandonment or 
cessation.77  The Early Termination Amount protects a specified portion of the revenue 
contribution projected for the remainder of the CRA term: 
Early Termination Amount = (Applicable Termination Percentage × Present 
Value of Remaining Projected Committed Revenue Contributions) − 
Applicable Credits 
The Applicable Termination Percentage increases as the project advances.78  Under the 
current proposal, the percentage is 25 percent before execution of the Final PJM Agreement, 50 
percent during the first 180 days after execution, 75 percent thereafter until the first Service Date, 
and 100 percent on and after the first Service Date.79  This graduated increase in financial 
obligations gives the initial commitment economic substance, while recognizing that early-stage 
withdrawal or change in load commitment is likely to have fewer detrimental impacts on other 
customers and the overall efficiency of the process, as compared to terminations that occur after 
the end of PJM’s process and closer to the Large Load’s planned in-service date.80  It also reflects 
the increasing reliance that may be placed on the Large Load Customer and its anticipated revenue 
contribution as Transmission Owners undertake engineering, procurement, construction, and other 
development activities with respect to the IRRs needed to serve the Large Load Customer and 
other customers in the applicable PJM study cluster. 
The termination provisions serve an important project-readiness function. They are 
appropriately not limited to the recovery of costs that can be traced to particular transmission 
facilities or stranded investments.  By requiring a Large Load Customer to commit to a meaningful 
financial stake as the project advances, the termination provisions also discourage speculative or 
insufficiently developed requests from entering and remaining in the transmission service process. 
This structure advances the Commission’s objective of using meaningful financial commitments 
 
75  
Proposed pro forma CRA, Part IX, Subpart P at Article 9.1. 
76  
Id. at Article 9. 
77  
Id. at Articles 9.2, 9.3. 
78  
See Blazunas and Hammer Direct Joint Testimony at 40-42. 
79  
Proposed pro forma CRA, Part IX, Subpart P at Exhibit D. 
80  
Blazunas and Hammer Direct Joint Testimony at 41-42.

PDF page 20

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 20 
 
 
 
 
to improve the viability of Large Load-related transmission service requests and reduce the 
potential for speculative requests to consume study and planning resources or distort transmission 
planning assumptions.  It also reduces the potential that speculative requests will adversely affect 
other Large Load-related transmission service requests and their ability to receive service in a 
timely manner.81 
Payment of a Partial Termination Amount applies only to the portion of the commitment 
permanently reduced.82  Amounts already received or applied to the same prospective exposure, 
including qualifying Credit Support proceeds and identifiable replacement-load revenues, reduce 
the termination amount.  The termination obligations are therefore protective rather than punitive: 
they are tied to the remaining projected revenue contribution, adjusted according to the Large Load 
Customer’s stage in the process, and reduced by amounts already recovered or otherwise 
attributable to the same exposure. 
As discussed in Section 10 below, proposed CRA section 9.12 and proposed Tariff, Part 
VIII, Subpart N, section 441(e) govern the application and distribution of termination amounts 
collected before the first Service Date. 
6. 
Service Dates Determine When the Periodic Revenue Commitment 
Begins. 
If the Large Load Customer proceeds, each portion of the recurring revenue commitment 
begins on the corresponding Service Date identified in CRA, Exhibit A.  For an authorized load 
ramp included in the CRA, the Committed Revenue Contribution increases as the scheduled stages 
of the Firm Load Commitment become effective.  The CRA also accounts for circumstances in 
which Firm Transmission Service cannot begin because necessary transmission facilities have not 
been completed.83  If the delay is not caused by the Large Load Customer’s or Eligible Customer’s 
failure or lack of reasonable diligence, the affected Service Date and corresponding contribution 
are extended until the service becomes available.84  If a qualifying transmission-facility delay 
reaches the threshold specified in the CRA, the Large Load Customer may accept revising the 
timing to ramp up its load or terminate under the CRA’s limited delay provision.85  The qualifying 
delay period is excluded when determining the applicable termination milestone so that the Large 
Load Customer does not move into a higher termination percentage solely because of a delay it 
did not cause. 
 
 
81  
Show Cause Order at P 56.  
82  
Proposed pro forma CRA, Part IX, Subpart P at Exhibit D, Section 5. 
83  
Id. at Article 5.5. 
84  
Id. at Article 5.5. 
85  
Id. at Article 9.6.

PDF page 21

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 21 
 
 
 
 
7. 
The CRA Establishes a Minimum Revenue Contribution Based on the 
Firm Load Commitment. 
The Early and Partial Termination Amounts discussed above address the remaining 
projected revenue exposure if the Large Load Customer exits or permanently reduces its Firm 
Load Commitment.  By contrast, if the Large Load Customer proceeds, the Committed Revenue 
Contribution defines the minimum periodic transmission-revenue contribution required under the 
CRA once the applicable Service Dates begin.86  Beginning on the applicable Service Dates, the 
Transmission Owner determines the revenues that would be associated with Firm Transmission 
Service corresponding to the Firm Load Commitment and applies the Minimum Commitment 
Percentage specified in Exhibit A.  The resulting amount is the Committed Revenue Contribution: 
Committed Revenue Contribution = Minimum Commitment Percentage × 
Full Firm Transmission Service Benchmark87 
The Minimum Commitment Percentage may vary between 80 and 100 percent, and may 
change over the CRA term under a schedule identified in Exhibit A.88  As discussed in the Joint 
Blazunas and Hammer Direct Joint Testimony, the proposed Minimum Commitment Percentage 
is reasonable because it establishes “a meaningful minimum revenue commitment while allowing 
individual Transmission Owners to require a higher commitment where appropriate based on their 
particular circumstances.”89  Together with the authorized load ramp and applicable Service Dates, 
this flexibility allows the Committed Revenue Contribution to reflect the Large Load’s individual 
circumstances, including its expected progression and the timing of the associated transmission-
revenue exposure.  This structure implements the Commission’s preliminary view that the 
minimum contribution should be related to the MW level of jurisdictional transmission service 
requested on behalf of the Large Load, while accommodating the request’s progression toward full 
service.90 
8. 
The CRA Recognizes Revenues Actually Produced as a Result of the 
Transmission Service Provided. 
The Committed Revenue Contribution establishes the minimum periodic contribution 
required under the CRA.91  For each Measurement Period, the Transmission Owner compares that 
amount with the Actual Revenue Contribution, which consists of the qualifying revenues 
attributable to Firm Transmission Service actually taken by the Eligible Customer to serve the 
Large Load Customer.92  The Committed Revenue Contribution and the revenues credited against 
 
86  
Id. at Article 5.1. 
87  
Blazunas and Hammer Direct Joint Testimony at 37-38. 
88  
Id. at 35-37. 
89  
Id. at 36-37. 
90  
Show Cause Order at P 83. 
91  
Blazunas and Hammer Direct Joint Testimony at 35-36. 
92  
Proposed pro forma CRA, Part IX, Subpart P at Article 5.2 and Exhibit B.

PDF page 22

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 22 
 
 
 
 
it are calculated using corresponding categories of transmission charges.93  This ensures a 
consistent comparison and gives the Large Load Customer credit for all qualifying revenues 
corresponding to the charges included in that calculation. 
Because the Eligible Customer takes the underlying transmission service, it must provide 
or authorize access to the billing, settlement, load, and allocation information needed to identify 
the revenues attributable to the Large Load Customer.94  That information-sharing obligation 
allows the Transmission Owner to administer the CRA while preserving the Large Load 
Customer’s separate responsibility for the financial obligations.  The CRA also accommodates 
existing retail arrangements.  To the extent the Large Load Customer makes separate payments 
through a retail tariff or other retail mechanism that reflect the assignment of Firm Transmission 
Service or related costs to the Large Load Customer, those payments are taken into account in 
determining the Actual Revenue Contribution, insofar as doing so does not shift costs to other 
Eligible Customers taking service in the Transmission Owner’s Zone.95  This treatment recognizes 
qualifying retail payments without permitting the associated transmission costs to be shifted to 
other customers. 
9. 
Under the CRA, the Large Load Customer Pays Only the Resulting 
Shortfall. 
At the end of each Measurement Period, the Transmission Owner compares the qualifying 
revenues attributable to the Large Load Facilities with the Committed Revenue Contribution: 
Shortfall Amount = Committed Revenue Contribution − Actual Revenue 
Contribution 
If recognized revenues equal or exceed the committed amount, no Shortfall Amount is due 
under the CRA.96  If recognized revenues are lower, the Large Load Customer pays only the 
difference.97  The Shortfall Amount is therefore a true-up of the agreed minimum contribution, not 
a second charge for the same Firm Transmission Service.  The Eligible Customer continues to pay 
the charges imposed under the Tariff for service actually taken, and the qualifying revenues 
produced by that service are credited against the Committed Revenue Contribution before any 
CRA payment is calculated.  
This mechanism protects other transmission customers by ensuring receipt of the minimum 
contribution associated with the Large Load commitment.98  The Large Load Customer receives 
 
93  
Id. at Article 5.1. 
94  
Id. at Article 5.6. 
95  
Id. at Article 5.2. 
96  
Id. at Article 5.3. 
97  
See proposed pro forma CRA, Part IX, Subpart P at Article 7; see also Blazunas and Hammer Direct Joint 
Testimony at 32-34. 
98  
Id. at 35-36.

PDF page 23

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 23 
 
 
 
 
credit for the qualifying revenues actually produced by service to its facilities and does not pay 
both ordinary transmission-service charges and a duplicative CRA payment for the same 
contribution. Although the mechanism is principally intended to protect other transmission 
customers from cost shifting, the CRA includes procedural and substantive safeguards to ensure 
that the Large Load Customer pays no more than the amount properly due.  The Transmission 
Owner must support any invoiced Shortfall Amount, and the Large Load Customer may review 
and dispute the calculation.99  Payment and Credit Support obligations remain in effect during the 
dispute, but any overpayment or excess draw must be returned after the dispute is resolved. 
10. 
Pre-Service Date Termination Amounts are Shared Among Affected 
Transmission Owners, and Collected Amounts are Credited Without 
Duplicate Recovery. 
The Commission stated that CRA payments should reduce the applicable Transmission 
Owner’s transmission revenue requirement consistent with the Commission’s cost-of-service 
regulations and contemplated a formula rate workpaper showing that treatment.100  Consistent with 
that guidance, collected Shortfall Amounts reduce the applicable transmission revenue 
requirement and remain subject to the Transmission Owner’s formula rate protocols and 
Commission review.101  Credit Support remains collateral unless and until it is applied to an 
amount due. 
CRA section 9.12 provides that, if an Early Termination Amount or Partial Termination 
Amount is payable before the first Service Date, the collected amount is first applied to Project 
Development Costs in accordance with proposed Tariff, Part VIII, Subpart N, section 441(e).  This 
treatment recognizes that facilities needed to serve a Large Load may be cancelled or otherwise 
abandoned as a result of Early or Partial Termination by one or more Large Load Customers.  
Moreover, because multiple Transmission Owners may be affected by such IRR cancellations or 
abandonments resulting from the termination of a Large Load Customer, Early or Partial 
Termination by a Large Load Customer could result in the cancellation of projects not only by the 
Transmission Owner that is the signatory to the applicable CRA, but also by other Transmission 
Owners within PJM.   
Proposed Tariff, Part VIII, Subpart N, section 441(e) addresses this situation by providing 
a mechanism for the distribution of  Partial and Early Termination Amounts among the contracting 
Transmission Owner and other eligible Transmission Owners based on their respective pro rata 
shares of the applicable Eligible Costs, if any, which are derived from costs reported on the 
applicable Transmission Owner’s FERC Form 1.102  This sharing mechanism prevents the entire 
 
99  
Proposed pro forma CRA, Part IX, Subpart P at Articles 7.4, 7.5. 
100  
Show Cause Order at P 84. 
101  
Proposed pro forma CRA, Part IX, Subpart P at Article 7.6. 
102  
Eligible Costs are defined as all expenditures, costs, and cancellation fees incurred or due to commitments 
made by the third-party Transmission Owner to engineer, design, procure, construct, own, operate, maintain, and 
service the Interconnection Reliability Reinforcements needed to serve the Eligible Customer taking transmission 
service on behalf of the Eligible Load or Large Load, but which will no longer be constructed, which (a) are incurred

PDF page 24

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 24 
 
 
 
 
payment from remaining with the contracting Transmission Owner while other affected 
Transmission Zones continue to bear costs associated with IRRs no longer needed.  Any amount 
remaining after the application of Termination Amounts to Eligible Costs of the applicable 
Transmission Owner is credited to the contracting Transmission Owner’s transmission revenue 
requirement to the benefit of other customers in the Zone.  If termination occurs on or after the 
first Service Date, the applicable termination amount is credited to the Transmission Owner’s 
Transmission Revenue Requirement for the Transmission Zone in which the Eligible Customer 
would have taken Firm Transmission Service.  The different treatment reflects the change in the 
nature of the protected exposure.  Before the first Service Date, termination may result in Eligible 
Costs associated with the cancellation or abandonment of facilities being constructed by 
Transmission Owners; after service begins, the termination amount solely protects other customers 
in the amount of the remaining prospective revenue contribution under the CRA, which is tied to 
the contracting Transmission Owner’s zonal transmission revenue requirement.  In neither case do 
Transmission Owners benefit financially from the allocation of Termination Amounts. 
The CRA and proposed Tariff provisions contain additional protections against double 
recovery.103 Actual revenues reduce periodic Shortfall Amounts; amounts already applied to the 
same exposure reduce termination obligations; qualifying retail and replacement-load revenues are 
recognized where appropriate; and collateral is not treated as revenue until applied.  In addition, a 
Transmission Owner may not seek recovery through an abandoned-plant filing or another 
proceeding for amounts already received through the Tariff, Part VIII, Subpart N, section 441(e) 
distribution process.  Together, these provisions ensure that CRA recoveries follow the associated 
exposure across affected Transmission Owners without providing duplicative recovery. 
11. 
The Proposed Pro Forma CRA and Generic Tariff Provisions Provide 
a Transparent and Flexible Cost Recovery Framework. 
Proposed Tariff, Part VIII, Subpart N, sections 441(c) and (d) establish uniform procedures 
and deadlines for tendering, negotiating, executing, securing, and filing the CRA.  Filing the CRA 
as a pro forma agreement gives Large Load Customers and Eligible Customers advance notice of 
the commitment, Credit Support, shortfall, termination, crediting, and information-sharing 
obligations that will apply when a Large Load-related transmission service request proceeds 
through PJM’s Fast Energization Process, while permitting the project-specific terms 
contemplated by the form to reflect differences in service, timing, load ramp, and applicable rates. 
As discussed above, the Tariff also permits existing or separate agreements to satisfy the 
CRA requirement where they provide comparable protection.  Proposed section 441(a)(ii) permits 
a separate Commission-accepted agreement that, together with applicable federal and state 
requirements, establishes minimum Firm Transmission Service and credit standards or other 
 
through the end of the calendar year in which notice of termination was received from the contracting Transmission 
Owner, and (b) are included in amounts reported in the Transmission Owner’s FERC Form 1 covering that calendar 
year.  See proposed Tariff, Part VIII, Subpart N, section 441(e)(ii).  
103  
See Proposed Tariff, Part VIII, Subpart N, section 441(e); see also proposed pro forma CRA, Part IX, 
Subpart P at Exhibit D.

PDF page 25

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 25 
 
 
 
 
comparable protections against cost shifting.  Section 441(b) preserves qualifying existing 
agreements, and section 441(e)(v) requires alternative agreements to contain reasonably 
comparable termination-payment crediting provisions.   
The proposal also expressly preserves qualifying existing agreements.104  Where a Large 
Load, including an anticipated load ramp, is already covered by a qualifying existing agreement, 
that agreement and the commitments reflected in it need not be replaced by the pro forma CRA 
merely because the new CRA framework becomes effective.  The grandfathering provision thus 
preserves arrangements and commitments already in place under the existing framework. 
12. 
The Proposed CRA is Just and Reasonable and Not Unduly 
Discriminatory or Preferential. 
The CRA is just and reasonable because it implements the protections identified by the 
Commission while accommodating the practical requirements of Large Load development.105  It 
permits projects to advance through the applicable load interconnection study and transmission 
service processes while establishing, at appropriate milestones, a defined and financially secured 
commitment corresponding to the Firm Transmission Service requested on their behalf.  This 
structure supports the timely integration of viable Large Loads without requiring existing 
transmission customers to fully bear the revenue consequences if a project does not proceed as 
represented or takes less service than anticipated. 
The CRA also assigns responsibilities according to the parties’ respective roles.  The Large 
Load Customer assumes the payment and Credit Support obligations associated with the project it 
controls.  The Eligible Customer remains responsible for requesting and taking transmission 
service and providing the information necessary to administer the agreement.  The Transmission 
Owner calculates and reconciles the applicable amounts, administers Credit Support, and credits 
collected amounts through its Commission-jurisdictional rate.  PJM continues to administer the 
transmission-service study process.  This allocation places each obligation with the entity best 
positioned to perform it without altering the established responsibilities for authorizing service or 
planning and constructing transmission facilities. 
The Large Load Customer’s financial commitment is also adjusted as the project develops. 
Before completion of PJM’s process, the CRA is based on the Initial Load Commitment and 
secures the consequences of advancing the request. Following execution of the Final PJM 
Agreement, the commitment is conformed to the amount and timing of Firm Transmission Service 
established through PJM’s process.  The Credit Support Requirement is likewise recalculated, but 
it remains based on 100 percent of the projected full-service benchmark for the remaining term 
rather than on the Minimum Commitment Percentage or projected future actual revenues.  If 
service begins, the Large Load Customer receives credit for qualifying revenues attributable to 
Firm Transmission Service actually taken to serve the Large Load Customer and pays only the 
resulting Shortfall Amount.  If the project exits or is permanently reduced, the applicable 
 
104  
Proposed Tariff, Part VIII, Subpart N, section 441(b). 
105  
Blazunas and Hammer Direct Joint Testimony at 43.

PDF page 26

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 26 
 
 
 
 
termination obligation addresses the remaining prospective exposure based on the stage reached 
by the project and the amounts already recovered. 
These protections support efficient transmission development while protecting customers 
in the precise fashion the Commission suggested in the Show Cause Order.106  Requiring a defined 
commitment and Credit Support at identified stages gives PJM and the PJM Transmission Owners 
a more reliable basis for devoting study, planning, engineering, procurement, and construction 
resources to Large Load-related transmission service requests.  At the same time, conforming the 
commitment to PJM’s final service determination, recognizing qualifying actual and retail 
revenues, reducing Credit Support as obligations are resolved, and preventing duplicate recovery 
protect the Large Load Customer against obligations exceeding the exposure addressed by the 
CRA.  Although the amount of Credit Support may exceed the periodic or termination amount 
ultimately payable because it is calculated using 100 percent of the projected benchmark, Credit 
Support remains collateral and does not determine or increase the underlying payment obligation. 
The filed framework is also not unduly discriminatory or preferential.  The pro forma CRA 
establishes the same core commitment, security, shortfall, termination, crediting, and information-
sharing requirements for similarly situated Large Loads.  Differences in service quantities, load 
ramps, Service Dates, calculation periods, applicable rates, and Credit Support reflect relevant 
differences in the service requested, project timing, and the applicable Transmission Owner’s rate 
structure.  Existing or separate agreements may substitute for the pro forma CRA only where they 
provide comparable protection against cost shifting, including appropriate service commitments, 
financial security, and treatment of termination payments.  
Taken together, these provisions respond directly to the Commission’s concerns while 
recognizing the scale and pace of Large Load development in PJM.  They provide a workable 
framework for advancing projects prepared to make and secure the commitments on which 
transmission planning and investment will rely, while protecting existing transmission customers 
if the anticipated Firm Transmission Service contribution does not materialize.  The resulting 
allocation of obligations is proportionate to the risks addressed, consistent with the parties’ 
respective roles, and reasonably designed to support both Large Load integration and efficient 
transmission infrastructure development. 
 
 
 
 
 
106  
Show Cause Order at PP 81, 83-84.

PDF page 27

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 27 
 
 
 
 
B. 
Transmission Service Rates and Related Charges for Co-Located Load and 
Large Load 
1. 
The Filing Satisfies the Remaining Co-Located Load Rate Compliance 
Directives. 
a. 
Transmission Services. 
The Co-Located Load Paper Hearing Order found the PJM Transmission Owners’ rate 
treatment proposals for FCDS and Interim NITS just and reasonable.107  However, the Commission 
rejected the PJM Transmission Owners’ proposed NFCDS maximum rate and required a lower 
maximum rate or nondiscriminatory discounts supported by transparent calculations.  
Accordingly, the PJM Transmission Owners’ filing implements the rate treatments already found 
just and reasonable for FCDS and Interim NITS through compliance tariff records,108 and proposes 
a revised NFCDS discounted rate methodology and related tariff provisions in compliance with 
the Commission’s directives.109 
 
The Co-Located Load Paper Hearing Order also found the Tariff unjust and unreasonable 
because it does not include transmission services that reflect Eligible Customers taking 
transmission service on behalf of loads with behind-the-meter generation (“BTMG”) that are 
willing and able to limit their energy withdrawals from the transmission system under certain 
conditions.110  The Commission directed (i) PJM to revise its Tariff to extend the three new 
transmission services set forth in the December 18 Show Cause Order to Eligible Customers taking 
service on behalf of load with BTMG that are willing and able to limit their energy withdrawals 
from the transmission system under certain conditions, and (ii) the PJM Transmission Owners to 
reflect this change in their compliance filing.111  Accordingly, the PJM Transmission Owners 
acknowledge in this compliance filing the extension of FCDS, NFCDS, and Interim NITS to 
Eligible Customers taking service on behalf of load with BTMG (i.e., Eligible Load)112 that 
includes necessary control technologies and/or protection systems that limit their energy 
withdrawals from the transmission system under certain conditions. 
 
 
107  
Co-Located Load Paper Hearing Order at PP 398, 572. 
108  
Id. at PP 398, 400, 401.  As noted above, the PJM Transmission Owners are including with this filing the 
tariff changes from their August 17 Compliance that are still relevant due to the fact that PJM is requesting an earlier 
effective date for those provisions.  The PJM Transmission Owners intend to withdraw the August 17 Compliance 
Filing shortly after the instant filing is made. 
109  
Co-Located Load Paper Hearing Order at PP 400, 401, 412. 
110  
Id. at P 101. 
111  
Id. at PP 101, 412, 572. 
112  
PJM defines “Eligible Load” in its Tariff as “Co-Located Load or load connected to Behind the Meter 
Generation.”  See Tariff, Part I (Definition of Eligible Load).

PDF page 28

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 28 
 
 
 
 
2. 
Financial Penalties for Unreserved Transmission System Use. 
In the Co-Located Load Paper Hearing Order, the Commission determined that it is just 
and reasonable to impose financial penalties on Eligible Customers in any circumstance where the 
transmission customer uses a transmission service that it has not reserved.113  The Commission 
directed the PJM Transmission Owners to effectuate on compliance their proposed penalty 
framework for financial penalties for Eligible Customers taking one of the three new transmission 
services that withdraw from the transmission system in excess of their contract demand level (i.e., 
for unreserved use).114  The Commission also noted that, on compliance, the PJM Transmission 
Owners’ unreserved use penalties should be distributed to all non-offending transmission 
customers, not just Eligible Customers taking Interim NITS and FCDS, consistent with Order No. 
890.115  Accordingly, the PJM Transmission Owners’ filing implements the financial penalty 
framework the Commission found just and reasonable, including the distribution of revenues 
collected from financial penalty charges to Eligible Customers taking NFCDS, in addition to firm 
customers.116 
C. 
Extension of Transmission Services and Financial Penalties for Unreserved 
Transmission System use to Eligible Large Load 
In the Show Cause Order, the Commission asked PJM to explain whether the Tariff 
remains just and reasonable if the three new services for Co-Located Load customers (i.e., Interim 
NITS, FCDS, and NFCDS) are not also made available to Eligible Customers taking service on 
behalf of flexible and electrically proximate Large Loads.117 
In its filing on compliance with the Show Cause Order, PJM is extending the same three 
transmission services to Eligible Customers taking transmission service on behalf of Large Load 
customers, as it offers to Eligible Customers taking transmission service on behalf of Co-Located 
Load customers in Docket Nos. EL25-49, et al., with substantially the same requirements for 
protective systems and operational compliance.118   
Consistent with this approach, the PJM Transmission Owners propose, pursuant to FPA 
section 205, to apply to Eligible Customers taking these transmission services on behalf of Large 
Load customers the same corresponding rate and financial penalty frameworks that apply to 
Eligible Customers taking transmission service on behalf of Co-Located Load customers, 
 
113  
Co-Located Load Paper Hearing Order at P 517. 
114  
Id. at PP 517, 529. 
115  
Id. at P 529. 
116  
Id. at PP 517, 529. 
117  
Show Cause Order at P 87. 
118  
PJM Interconnection, L.L.C., Co-Located Load Order Workshop Meeting Materials, Item 02 (Nov. 11, 
2026), 
https://www.pjm.com/-/media/DotCom/committees-groups/workshops/cllsco/2026/20261112/20261112-
item-02---tariff-revisions-part-xi-new-transmission-services-november-11-draft---redline.pdf 
(Tariff 
Part 
XI 
revisions).

PDF page 29

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 29 
 
 
 
 
contingent on the Commission accepting the underlying services proposed in PJM’s compliance 
filing.119  Except for the revised NFCDS discounted-rate methodology and adjustments necessary 
to conform to PJM’s final service design, the proposed rates distinguish among customers based 
on the transmission service taken, not whether the customer takes that service on behalf of Co-
Located Load or another eligible Large Load. 
The proposed tariff records provided as part of this filing amend Part XI of the Tariff and 
the applicable rate schedules to address: 
1. 
FCDS, which is intended for the portion of load that will rely on the transmission 
system under normal operating conditions and for which Network Upgrades are 
planned and built;  
2. 
NFCDS, a limited, supplemental service intended to provide as-available 
transmission capacity;  
3. 
Interim NITS, a non-firm service available while Network Upgrades needed to 
provide full NITS are being constructed; 
4. 
The treatment of administrative, ancillary-service, redispatch, Schedule 12, and 
other applicable charges; 
 
5. 
Revenue credits associated with NFCDS; and 
 
6. 
Financial penalties and related revenue credits for unreserved transmission use. 
 
1. 
Firm Contract Demand Transmission Service Rates and Charges. 
The PJM Transmission Owners’ proposed rates for FCDS are identical to those set forth in 
the Transmission Owners’ reply brief in Docket Nos. EL25-49-000, et al.120  The rate for FCDS 
will be calculated in a manner essentially identical to the existing NITS rates, using each applicable 
transmission owner’s specific methodology for NITS customers.121  Under this approach, Eligible 
Customers taking FCDS will pay the same base charge per megawatt (“MW”) as NITS customers, 
except that unlike NITS customers their demand will be their specified firm contract demand equal 
to the firm contract demand amount (in MW) multiplied by a single zonal rate for both NITS and 
FCDS customers.  The Commission agreed with this approach in the Co-Located Load Paper 
Hearing Order, finding it just and reasonable to base the Firm Contract Demand rate on zonal NITS 
rates and underlying NITS revenue requirements because both services provide a similar level of 
 
119  
Blazunas and Hammer Direct Joint Testimony at 7-8. 
120  
PJM Transmission Owners Reply Brief at Exhibit No. PTO-0006. 
121  
PJM Transmission Owners Reply Brief at 18.

PDF page 30

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 30 
 
 
 
 
firm transmission service and PJM will plan the transmission system to provide both on a firm 
basis.122 
 
For Zones in which NITS rates are determined pursuant to Attachment H formula rates, 
the monthly demand charge is calculated as follows:  MDC = FCDTSA × RTZ/12, where MDC is 
the monthly demand charge, FCDTSA is the Firm Contract Demand Transmission Service 
Amount in MW as specified in the Eligible Customer’s Service Agreement, and RTZ is the 
applicable zonal NITS rate stated in dollars per MW-year.123  For purposes of establishing RTZ 
under Attachment H, the annual peak of the zone shall include both Network Customer Loads and 
the FCDS amounts for all Eligible Customers taking FCDS in the zone during the applicable peak 
period.124   
Consistent with the Commission’s findings in the Co-Located Load Paper Hearing Order, 
all ancillary services other than regulation and black start will be charged based on the Eligible 
Customer’s contract demand, while regulation and black start services will be assessed on a gross 
demand basis—reflecting the Commission’s determination that all Co-Located Loads rely on those 
services to be served regardless of the extent to which they withdraw energy from the transmission 
system.125  PJM will procure capacity for Firm Contract Demand customers and will plan the 
transmission system to serve them at their contract demand level.126  Accordingly, capacity-related 
charges will be based on the customer’s Unforced Capacity Obligation.  Eligible Customers will 
also be responsible for applicable administrative service charges, redispatch costs under 
Attachment K, and Transmission Enhancement Charges for which they are designated as 
Responsible Customers under Schedule 12.127 
Revenue credits from NFCDS revenues will be applied each month to offset gross Firm 
Contract Demand charges on a pro rata basis, consistent with the crediting mechanisms previously 
approved in PJM’s Tariff.128  FCDS has a minimum one-year term and is subject to PJM’s anti-
toggling mechanism—which prohibits, for a period of five years, an Eligible Customer from taking 
NFCDS for any portion of Co-Located Load served by FCDS—and a 42-month termination-notice 
requirement, consistent with the notice provisions applicable to Network Customers.129 
 
 
 
122  
Co-Located Load Paper Hearing Order at P 398. 
123  
See proposed Schedule 20. 
124  
See id.; see also PJM Transmission Owners Reply Brief, Exhibit No. PTO-0006 at 6. 
125  
Co-Located Load Paper Hearing Order at PP 399-400. 
126  
Id. at P 250. 
127  
Co-Located Load Paper Hearing Order at P 401; PJM Transmission Owners Reply Brief, Exhibit No. PTO-
0006 at 3, 7. 
128  
PJM Transmission Owners Reply Brief, Exhibit No. PTO-0006 at 6-7. 
129  
Co-Located Load Paper Hearing Order at P 535.

PDF page 31

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 31 
 
 
 
 
2. 
Non-Firm Contract Demand Transmission Service Rates and Charges. 
In the Co-Located Load Paper Hearing Order, the Commission found that the PJM 
Transmission Owners’ original proposal to set the maximum Non-Firm Contract Demand rate 
equal to the Firm Contract Demand rate had not been shown to be just and reasonable,  
notwithstanding that it was subject to discount similar to Non-Firm Point-To-Point Service.130   
The Commission concluded that Non-Firm Contract Demand should not be subject to the same 
maximum rate as Firm Contract Demand.131  The Commission further directed the PJM 
Transmission Owners to propose either a lower maximum rate or non-discriminatory discounts, 
with transparent charge calculations for each individual transmission customer.132 
In compliance with the Commission’s directive, and as supported by the Blazunas and 
Hammer Direct Joint Testimony, the PJM Transmission Owners are proposing to set the NFCDS 
rate as a discounted rate established as a function of the zonal FCDS rate and the transmission 
system load factor for a zone.133  NFCDS customers will take service and pay their reserved 
amount of demand based on system availability, and NFCDS will be available for terms ranging 
from one hour to one month.134  To ensure against double recovery, all revenues received from 
NFCDS charges will be credited to NITS, Firm Point-To-Point, and FCDS customers based on 
their share of the coincident peak load. 
The rationale for this approach is that the transmission system is built to a peak driven by 
firm load.  As discussed in the Joint Blazunas and Hammer testimony, the difference between 
zonal annual energy and zonal annual energy at a 100% load factor represents a proxy for the 
“excess capacity” for which non-firm load is not responsible.135  Accordingly, a lower zonal load 
factor indicates relatively more spare capacity and justifies a higher discount, and vice versa.  A 
simplified example of this rate calculation for a zone is set forth below in Example 2: 
Example 2 – Discounted Non-Firm Contract Demand Transmission Service Rate 
Calculation 
 
1  The zonal Firm Contract Demand Rate is $90,000/MW-Year 
2  The zonal peak demand is 150,000/MW. 
3  The zonal annual energy is 850,000,000 MWh 
4  The maximum non-firm contract demand equals $90,000/MW-Year x [Line 3 ÷ (Line 2 
x 8,760 hours)] = $90,000/MW-Year x 64.7% Load Factor ≈ $58,219/MW-Year. 
 
130  
Id. at P 402. 
131  
Id.  
132  
Id. at PP 404, 412. 
133  
Proposed Tariff, Part XI, Subpart C, Section 715 and Proposed Schedule 21; see also Blazunas and Hammer 
Direct Joint Testimony at 9-10. 
134  
Daily and hourly rates will be distinguished based on on-peak days (Monday–Friday, except for certain 
holidays) and off-peak days (Saturday and Sunday, including the applicable holidays that fall on a weekday). 
135  
Blazunas and Hammer Direct Joint Testimony at 10.

PDF page 32

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 32 
 
 
 
 
5  The discounted NFCD rate has an implied discount of 35.3% relative to the Zonal Firm 
Contract Demand Rate (i.e., the Maximum NFCD rate).136 
The PJM Transmission Owners’ proposed discounted NFCDS rate is just and reasonable 
and consistent with cost causation principles, as well as the Commission’s directives in the 
December 18 Show Cause Order and Co-Located Load Paper Hearing Order because it 
incentivizes efficient use of the transmission system by Eligible Customers seeking to use the 
transmission system on behalf of Co-Located or Large Load in a more limited manner and aligns 
the charges for NFCDS with the benefits received.137  This methodology is also transparent and 
non-discriminatory, as it relies on publicly available PJM zonal data, such as peak loads and net 
energy figures from PJM’s Long-Term Load Forecast, and applies a consistent calculation across 
all PJM zones.138   
3. 
Interim Network Integration Transmission Service. 
On August 17, 2026, the PJM Transmission Owners submitted new and revised Tariff 
records in partial compliance with the Commission’s Co-Located Load Order to implement the 
rate for Interim NITS.139  The filing was a companion filing to PJM’s August 17 Compliance Filing 
of the Tariff terms and conditions for Interim NITS.140   
The PJM Transmission Owners propose limited modifications to the language contained 
in their August 17 Compliance Filing to account for the provision of this service to Eligible 
Customers taking service on behalf of Large Load customers,141 as well as to reflect 
implementation of FCDS and NFCDS. 
Interim NITS is a temporary, non-firm transmission service available to an Eligible 
Customer that has requested NITS but cannot yet reliably receive it because the Network Upgrades 
necessary to provide permanent NITS are not yet complete.142  The Commission found that Interim 
NITS is an optional service, available only to the extent PJM determines—in consultation with the 
affected Transmission Owner—that some level of interim service can be reliably provided based 
on the results of appropriate studies.143  Once the required Network Upgrades are completed and 
integrated with the PJM transmission system, the Eligible Customer automatically converts to 
 
136  
Id. at 10 (Table 1). 
137  
December 18 Show Cause Order at PP 199, 214; Co-Located Load Paper Hearing Order at PP 402-407, 412. 
138  
Blazunas and Hammer Direct Joint Testimony at 10. 
139  
See supra note 23. 
140  
Id. 
141  
See supra notes 24 & 108; Proposed Tariff, Part XI, Subpart A, Section 706. 
142  
Co-Located Load Paper Hearing Order at P 248. 
143  
Id. at P 574.

PDF page 33

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 33 
 
 
 
 
Network Customer status and begins taking permanent NITS.  Interim NITS may not be combined 
with FCDS or NFCDS.144 
As with FCDS, the PJM Transmission Owners’ proposed rates for Interim NITS are the 
same as those applicable to Co-Located Load customers under the PJM Transmission Owners’ 
filings in Docket Nos. EL25-49, et al.145  The monthly demand charge for Interim NITS is 
calculated as the Eligible Customer’s measured demand amount in MW multiplied by the 
applicable zonal NITS rate established pursuant to Tariff Section 34.1.146  This is the same rate 
methodology that applies to permanent NITS customers, consistent with the Commission’s finding 
that Eligible Customers taking Interim NITS should pay the NITS rate.147  However, because 
Interim NITS is an interruptible service, Eligible Customers taking Interim NITS service on behalf 
of Co-Located Loads or Large Loads would not be assessed generation capacity charges because 
capacity will not be procured on behalf of Interim NITS customers until such time as Network 
Upgrades are in place to serve them.148 
Interim NITS customers will be responsible to pay for: (i) applicable administrative service 
charges under Tariff Schedules 1A, 9, and 10; (ii) ancillary service charges, including regulation 
charges and black start service charges; and (iii) redispatch costs.149  The PJM Transmission 
Owners are not proposing tariff revisions in this filing to implement these charges and costs 
because the Commission directed PJM to incorporate Tariff revisions in its compliance filing 
necessary to assess them.150  Revenue credits from NFCDS revenues will be applied to offset the 
gross Interim NITS monthly demand charge, consistent with the crediting methodology applicable 
to other firm and non-firm service customers.151 
4. 
Financial Penalties for Unreserved Transmission System Use. 
As discussed above, the PJM Transmission Owners are filing the financial penalty 
framework found just and reasonable by the Commission in the Co-Located Load Paper Hearing 
Order, with a modification to the penalty revenue distribution, that will apply to Eligible 
Customers taking one of the new transmission services on behalf of not only Co-Located Loads, 
but also eligible Large Loads as well.  Under this PJM Transmission Owners’ financial penalty 
framework, an Eligible Customer would be assessed: (i) a base penalty charge for each hour in 
 
144  
December 18 Show Cause Order at P 200. 
145  
See PJM Transmission Owners Reply Brief, Exhibit No. PTO-0006 at 1-2. 
146  
Id. at 1. 
147  
Co-Located Load Paper Hearing Order at P 248. 
148  
Id. at P 248. 
149  
Co-Located Load Paper Hearing Order at PP 572-573. 
150  
See Co-Located Load Paper Hearing Order at P 573; see also PJM Interconnection, L.L.C., Co-Located Load 
Order Workshop Meeting Materials, Item 02 (Nov. 11, 2026), https://www.pjm.com/-/media/DotCom/committees-
groups/workshops/cllsco/2026/20261112/20261112-item-02---tariff-revisions-part-xi-new-transmission-services-
november-11-draft---redline.pdf (Tariff Part XI revisions).. 
151  
PJM Transmission Owners Reply Brief, Exhibit No. PTO-0006 at 1.

PDF page 34

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 34 
 
 
 
 
which the Eligible Customer’s reserved service limit is exceeded at the Point of Interconnection 
during at least one five-minute interval (an “Exceedance Hour”), and (ii) a penalty ratchet when 
exceedances occur repeatedly.152  Under the penalty ratchet, penalty charges escalate as the 
frequency of unreserved transmission use increases.153  If more than one Exceedance Hour occurs 
on the same day, an additional daily penalty would apply.154  If exceedances occur on multiple 
days within the same week, an additional weekly penalty would apply.  If exceedances occur in 
multiple weeks within the same month, an additional monthly penalty would apply.  Finally, if 
exceedances occur in multiple months within the same year, an additional annual penalty would 
apply.155  The Commission agreed with PJM Transmission Owners that progressively increasing 
the consequences of repeated penalties encourages Eligible Customers to manage their usage 
consistent with their reserved transmission service limit.156 
Consistent with the Commission’s guidance and Order No. 890,157 the PJM Transmission 
Owners are also modifying Schedule 22 to clarify that revenues collected from daily, weekly, and 
monthly financial penalty charges will be returned on a monthly basis to all non-offending 
transmission customers (i.e., FCDS, NFCDS, NITS, and Interim NITS customers) that have not 
been penalized during the month as bill credits, based on the Eligible Customer’s pro rata share 
of the Zone’s annual peak load based on the most recent 12-month period ending October 31.  
Revenues collected from annual penalty charges will be returned on an annual basis to all non-
offending transmission customers that have not been penalized during the year as bill credit, based 
on each Eligible Customer’s pro rata share of the Zone’s annual peak load based on the most 
recent 12-month period ending October 31. 
D. 
Cost Allocation and Recovery for Interconnection Reliability Reinforcements 
PJM’s proposed Fast Energization Process would study qualifying generation  
interconnection and Large Load-related transmission service requests together and identify a 
portfolio of transmission upgrades—the IRRs—needed to address the combined system impacts 
of the requests included in each study cycle.  PJM’s proposal necessitates revisions to the Tariff to 
establish the basis for allocating the costs of the IRRs that PJM identifies in each study cycle.  
Accordingly, the PJM Transmission Owners propose revisions to Schedule 12 of the Tariff that 
would allocate the costs of those IRRs on a portfolio basis using modeled electrical impacts of the 
generators and Large-Load-related transmission service requests being studied through PJM’s Fast 
 
152  
Id. at 16-17 & Exhibit No. PTO-0006 at 4-16. 
153  
Id. at 17 & Exhibit No. PTO-0006 at 7, 10-16. 
154  
Id., Exhibit No. PTO-0006 at 14. 
155  
Id. at 17 & Exhibit No. PTO-0006 at 12-14. 
156  
Co-Located Load Paper Hearing Order at P 529. 
157  
Id. at P 529; Preventing Undue Discrimination & Preference in Transmission Serv., Order No. 890, 118 
FERC ¶ 61,119, at PP 848, 862, order on reh’g, Order No. 890-A, 121 FERC ¶ 61,297 (2007), order on reh’g, Order 
No. 890-B, 123 FERC ¶ 61,299 (2008), order on reh’g, Order No. 890-C, 126 FERC ¶ 61,228, order on clarification, 
Order No. 890-D, 129 FERC ¶ 61,126 (2009).

PDF page 35

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 35 
 
 
 
 
Energization process.158  The IRRs themselves will be included in the transmission rate bases of 
the Transmission Owners constructing and owning the projects.  A new Interconnection Reliability 
Reinforcement Charge will be implemented to recover the costs from transmission customers 
external to the Zone(s) in which the IRRs are located, as well as a separate fee to be charged to 
generators in each cycle to recover and credit back to load customers amounts representing a fair 
contribution from those generators to offset the costs of the IRRs.    
In balancing the need for a cost allocation methodology that assigns costs in a manner 
roughly commensurate with benefits while also being efficient, practically implementable, and 
protecting other transmission customers, the PJM Transmission Owners’ proposed cost allocation 
approach is intended and will achieve the same goals as the cost allocation framework the 
Commission recently approved for Southwest Power Pool, Inc. (“SPP”).159  In particular, as with 
SPP’s cost allocation approach, the PJM Transmission Owners’ cost allocation proposal departs 
from the traditional “but-for” cost assignment model that links specific transmission upgrades with 
specific requests for service.  In the case of SPP, the Commission accepted SPP’s GRID-C 
mechanism for allocating a portion of the costs of transmission facilities to prospective generator 
interconnection customers through fixed per-MW charges that, when collected, are credited back 
against load customer cost responsibility.160 
Although employing different mechanisms due in part to the nature of the Fast Energization 
process proposed by PJM, which is different than the planning process implemented by SPP,161 
the PJM Transmission Owners’ proposal aligns with the same objectives as the SPP cost allocation 
proposal in departing from the traditional “but for” generator interconnection cost allocation 
approach.  Under the proposed Schedule 12 provisions, PJM, as Transmission Provider, will use 
power-flow modeling to calculate the relative contributions of the studied generation and Large 
Load transmission requests to the aggregate transmission system violations on constrained 
facilities addressed by the IRRs.  Those calculations will form the basis of the Interconnection 
Reliability Reinforcement Charge to Zones with Large Load customers, as well as the separate fee 
recovered from generators in each study cycle (the “Generator Reliability Reinforcement Fee”).  
This aggregate approach is tailored to the output of PJM’s Fast Energization Process.  Because 
PJM plans to study multiple generation interconnection and Large Load transmission service 
requests together and identify shared reinforcements addressing multiple system violations, 
individual IRRs will not correspond to individual service requests.162  Such a one-to-one mapping 
would therefore be technically infeasible.  Thus, it is necessary to have a method for allocating the 
 
158  
See Blazunas and Hammer Direct Joint Testimony at 11-12. 
159  
Sw. Power Pool, Inc., 194 FERC ¶ 61,192 at P 52 (2026). 
160  
Id. at PP 88-90 (applying the Commission’s “beneficiary pays” cost-causation principle and finding the 
GRID-C mechanism just and reasonable because it allocates the costs of anticipated network upgrades between 
prospective generator interconnection customers and load in a manner at least roughly commensurate with benefits). 
161  
This discussion relates solely to the features of SPP’s cost allocation proposal, and is not intended to draw 
any comparisons between SPP’s Consolidated Planning Process and the PJM Fast Energization Process, or address 
the merits of PJM’s Fast Energization Process. 
162  
Blazunas and Hammer Direct Joint Testimony at 12.

PDF page 36

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 36 
 
 
 
 
costs of the IRRs that recognizes the integrated and portfolio-based nature of PJM’s proposed Fast 
Energization Process.163 
The resulting allocation maintains a demonstrable relationship between the studied 
requests’ modeled contributions to the identified system needs.  It uses the causal information 
produced through PJM’s study process without attributing individual reinforcements to particular 
requests in recognition of the fact that the study results do not establish that attribution.  This 
approach is consistent with PJM’s existing proportional impact method for allocating costs under 
its New Service Request process, as well as the governing cost allocation standard.  Costs assigned 
to customers must be “roughly commensurate” with the benefits those customers are expected to 
receive, but it need not calculate those benefits with exact precision.164  The PJM Transmission 
Owners’ proposal satisfies that standard by establishing a connection between the studied requests, 
their modeled contributions to the aggregate system violations, and the costs of the shared IRRs 
required to address those violations.  It thereby achieves a roughly commensurate cost allocation 
without attempting to impose a customer-by-customer or project-by-project cost assignment that 
is inconsistent with PJM’s Fast Energization study process.165  That practical approach achieves 
the same objectives as accepted by the Commission in its recent acceptance of SPP’s high impact 
large load (“HILL”) study process and High Impact Large Load Generation Assessment 
(“HILLGA”) framework.166 
The proposed allocation methodology, while complementing PJM’s combined study 
approach, is submitted as an independent FPA section 205 proposal supported on its own merits.  
The just and reasonable basis for the proposed Schedule 12 revisions does not depend on 
Commission acceptance of every feature of PJM’s companion filing.  Rather, the methodology is 
just and reasonable and can operate with any accepted study design that identifies a portfolio of 
transmission solutions and produces the modeled electrical-impact information necessary to 
allocate the resulting costs, regardless of whether that process is confined to Large Load-related 
transmission service requests or also includes generator interconnection requests. 
1. 
PJM Determines Cost Responsibility for the IRR Portfolio Using 
Modeled Electrical Impacts. 
For each Fast Energization Cycle, PJM will identify the IRRs designated for construction 
and determine, based on the provisions set forth in the instant PJM Transmission Owner proposal, 
cost responsibility for the resulting portfolio.  To determine cost responsibility, PJM will use 
power-flow modeling to calculate the proportional impact of each studied service request to the 
aggregate violations on the constrained facilities requiring mitigation through the IRR portfolio.  
This approach begins with the calculation by PJM of distribution factors based on the transfer of 
energy across constrained facilities as identified in the study process.  Proportional impacts for 
 
163  
See Midcontinent Indep. Sys. Operator, Inc. 189 FERC ¶ 61, 108 (2024), order on reh’g, 191 FERC ¶ 61,231 
(2025). 
164  
See, e.g., Ill. Com. Comm’n v. FERC, 576 F.3d 470, 476-77 (7th Cir. 2009). 
165  
See, e.g., PJM Interconnection, L.L.C., 193 FERC ¶ 61,217 at PP 166-168 (2025). 
166  
Sw. Power Pool, Inc., 194 FERC ¶ 61,031 (2026) (“SPP HILL Order”).

PDF page 37

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 37 
 
 
 
 
generators and loads are determined by multiplying the associated distribution factors, if they 
exceed the specified threshold, by the MW capacity for generators or amount of Firm Transmission 
Service requested by an Eligible Customer on behalf of the applicable Large Load.  For MW 
impacts that exceed a defined impact threshold, such impacts will be converted to proportional 
MW impacts representing the pro rata share of all impacts on the same constrained facility.  Then 
the proportional MW impacts are weighted using values as set forth in the PJM Manuals resulting 
in weighted proportional MW impacts.167  As discussed in the Blazunas and Hammer Direct Joint 
Testimony, weighting is important because the same degree of impact is not necessarily 
comparable between different facilities.168  For instance, a 1 MW impact on a 20-mile, 138 kV 
constrained facility is of significantly less consequence than a 1 MW impact on a 150 mile, 500 
kV constrained facility.169  
These features make the proposed tariff revisions a practical measure of cost causation.  
The methodology keys each share to the megawatts the customer actually requested, excludes 
immaterial impacts, and counts only impacts that aggravate a violation.  It therefore satisfies the 
Commission’s long-standing requirement that rates “reflect to some degree the costs actually 
caused by the customer who must pay for them” and that costs be allocated in a manner at least 
roughly commensurate with the benefits the paying entity receives.170  Nor does the methodology 
break new ground.  PJM’s Tariff already provides that all New Service Requests that contribute to 
the need for a Network Upgrade receive cost allocation based on each request’s contribution to the 
reliability violation, in accordance with the PJM Manuals.171  The PJM Transmission Owners’ 
proposal applies that same contribution-based principle, with reasonable modifications to reflect a 
process that studies generator interconnection and Large Load transmission service requests 
together and produces a single portfolio of projects to accommodate those requests.172 
2. 
Aggregate Impacts are Converted into Zonal Cost Responsibility 
Determinations, With Generator Costs Recovered Through a Levelized 
Fee. 
The PJM Transmission Owners’ proposed tariff revisions translate aggregate impact values 
into cost responsibility for the relevant IRRs.  The proportional impacts of Transmission Service 
Requests are combined on a Zonal basis and assigned to the relevant Transmission Owner Zones, 
with the entire initial cost responsibility allocated among to those Zones based on their relative 
 
167  
Blazunas and Hammer Direct Joint Testimony at 18-20 (providing a simple example to illustrate the proposed 
proportional impact methodology). 
168  
Id. at 16-17. 
169  
Id. at 16-17.  For short-circuit constraints, allocation turns on each customer’s contributing fault current 
impact on the circuit breaker’s interrupting rating.  See proposed Schedule 12, Section (f)(2)(B) and Blazunas and 
Hammer Direct Joint Testimony at 21-22. 
170  
See, e.g., Midwest ISO Transmission Owners v. FERC, 373 F.3d 1361, 1368 (D.C. Cir. 2004); Ill. Com. 
Comm’n v. FERC, 576 F.3d 470, 476 (7th Cir. 2009). 
171  
Show Cause Order at P 22. 
172  
Blazunas and Hammer Direct Joint Testimony at 17.

PDF page 38

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 38 
 
 
 
 
weighted impacts.173  The costs associated with the IRRs are included in the rate base of the 
Transmission Owners that will construct and own those facilities.  The allocations to other Zones 
are recovered through the Interconnection Reliability Reinforcement Charge, which is discussed 
further below.  The proposed tariff revisions also make these assignments public.  The 
Transmission Provider will complete the cost responsibility analysis before Transmission Service 
Agreements and Generator Interconnection Agreements are executed and before seeking PJM 
Board approval of the reinforcements through their inclusion in the RTEP, and it will post the 
resulting assignments on the PJM website within 30 days of completing the analysis.174  That 
posting requirement responds to, in part, the Commission’s concern that, without sufficient 
transparency, stakeholders may lack visibility into the transmission upgrades, and their associated 
costs, driven by large load additions.175 
The portion of reinforcement costs representing the relative contribution of generators in 
the applicable Fast Energization Process cycle is charged separately to the generators through 
Generator Reliability Reinforcement Fees.176  The Generator Reliability Reinforcement Fee 
translates each generator’s allocated share of reinforcement costs into a levelized payment 
obligation that is collected by PJM and credited to transmission customers in the relevant Zones 
that have been assigned cost responsibility for the IRRs.177  As explained above, each generator’s 
allocated share is determined using a distribution factor-based methodology comparable to PJM’s 
existing proportional impact allocation methodology.  Thus, each generator’s base contribution to 
the overall costs of the applicable portfolio of IRRs is derived using a Commission-endorsed 
approach to determining relative benefits. 
The assessment of a separate fee to generators is just and reasonable.  The Show Cause 
Order was explicit that the Commission did not intend to alter or question existing cost allocation 
methods.178  Consistent with this finding, the PJM Transmission Owners’ proposal preserves the 
foundational approach of including transmission system enhancements in Transmission Owners’ 
rate bases used to determine rates for transmission service, while providing appropriate ratepayer 
protections including the CRA and the additional mechanisms discussed below.  In PJM, load pays 
for transmission service.  However, the PJM Transmission Owners recognize that PJM’s combined 
study approach will consider impacts associated with generator interconnection requests, and thus, 
a contribution from generators to offset the costs of IRRs is appropriate.  Assessing a separate 
charge to generators, in the form of the proposed Generator Reliability Reinforcement Fee, 
provides a means to ensure an appropriate financial contribution from generators, while preserving 
 
173  
Proposed Schedule 12, Sections (f)(2)(C)(2), (f)(4), and (f)(6). 
174  
Id. at Section (f)(2)(D). 
175  
Show Cause Order at PP 71, 74-76. 
176  
Proposed Schedule 12, Sections (f)(2)(C)(2) and (f)(4). 
177  
See id. at Section (f)(6); see also Blazunas and Hammer Direct Joint Testimony at 23-24. 
178  
Show Cause Order at P 81.

PDF page 39

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 39 
 
 
 
 
the rate base treatment of IRRs consistent with longstanding cost allocation and recovery methods 
in PJM.179  
The PJM Transmission Owners propose to recover Generator Reliability Reinforcement 
Fees in a manner that balances several related goals: (i) maintaining consistency with PJM’s 
proposal to identify IRRs on a portfolio basis, taking into account all applicable generator 
interconnection and Large Load transmission service requests; (ii) providing an ongoing stream of 
credits to transmission customers that extends over a significant portion of the expected life of 
most transmission projects; (iii) recognizing generators’ finite operational lives and particular 
financing needs, while avoiding unduly long-term cost responsibility obligations that could 
discourage needed generation development in the PJM region; and (iv) providing generators with 
upfront cost certainty and commercially reasonable payment terms that avoid creating 
disincentives for generators to locate and build in PJM. 
To balance these considerations, each Generator Interconnection Customer will be 
assessed the applicable Generator Reliability Reinforcement Fee by PJM beginning on the earlier 
of the calendar year in which its facility achieves Commercial Operation or three years after the 
Commercial Operation date specified in its original Generator Interconnection Agreement, and the 
fee will continue for 15 years from that date.180  The Transmission Provider will calculate the fee 
on a levelized basis by applying the generator’s allocated percentage of the total portfolio of IRRs 
to the total estimated gross plant of those IRRs and multiplying the resulting amount by a capital 
recovery factor built from the Annual Carrying Charge Component.181  This Annual Carrying 
Charge Component is the same across all Generator Reliability Reinforcement Fees calculated 
within each cycle.  It is calculated based on the Transmission Owners’ Commission-accepted cost 
of capital: specifically, it is the weighted average of the Weighted Average Cost of Capital, drawn 
from the Attachment H formula rates of each Transmission Owner with reinforcements in the 
applicable Fast Energization Process study cycle that includes the Generator Interconnection 
Customer, weighted by that Transmission Owner’s share of the overall IRR portfolio from the 
applicable study cycle.182 
PJM will invoice one-twelfth of the annual Generator Reliability Reinforcement Fee 
monthly and credit the amounts collected to Firm Transmission Customers.183  Each Zone will 
receive credits in proportion to its share of the annual revenue requirement for the reinforcements 
allocated to Firm Transmission Customers, and each Zone’s credits will be distributed among its 
Firm Transmission Customers based on their pro rata share of the Zone’s annual peak load for the 
 
179  
Blazunas and Hammer Direct Joint Testimony at 23-25. 
180  
Proposed Schedule 12, Section (f)(6)(A). 
181  
See proposed Schedule 12, Section (f)(6)(B); see also Blazunas and Hammer Direct Joint Testimony at 23-
25. 
182  
Proposed Schedule 12, Section (f)(6)(B). 
183  
Id. at Section (f)(6)(C)-(D).

PDF page 40

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 40 
 
 
 
 
most recent 12 months ending October 31, appearing as a reduction to the gross monthly rate for 
Firm Transmission Service.184 
This approach achieves a just and reasonable balance among the goals described above. 
First, the 15-year recovery period recognizes the portfolio nature of the IRRs while ensuring that 
credits flow back to transmission customers for a substantial portion of the expected lifespan of a 
transmission portfolio.185  Tying the commencement of the fee to the generator’s Commercial 
Operation Date, with a reasonable allowance for timing changes, also appropriately accommodates 
differences between the timing of generator development and the placement of the associated 
transmission reinforcements in service.  In some instances, a generator may begin paying the fee 
before all transmission facilities in the associated IRR portfolio enter service, providing a relative 
benefit to transmission customers; in others, the generator may begin making payments after 
certain transmission facilities have entered service.  Across the portfolio, however, it is reasonable 
to expect these timing differences to roughly balance out. 
The Commission recently accepted a similarly pragmatic balancing approach in SPP, 
where it approved an expedited process for generators serving HILL that relies on standardized 
financial requirements rather than attempting to calibrate each requirement precisely to the costs 
or risks attributable to each individual generator.186  The Commission found those requirements 
just and reasonable because, among other things, the more stringent financial commitments and 
other eligibility requirements would encourage commercially ready projects.187  The PJM 
Transmission Owners’ approach is, if anything, more tailored: each Generator Reliability 
Reinforcement Fee begins with the generator’s modeled proportional contribution to the violations 
addressed by the applicable IRR portfolio and converts that impact into an administrable, levelized 
payment obligation.  Because the fee will be determined upfront based on the results of the PJM 
system impact study, generators will have certainty as to their costs before making a final 
commitment to move forward and execute an interconnection agreement.  Moreover, by limiting 
the recovery period to 15 years, rather than extending it over the full expected life of the IRRs, the 
proposal avoids imposing commercially unreasonable payment terms that could render otherwise 
viable generation projects unfinanceable.  That combination of cost certainty and reasonable 
payment terms is particularly appropriate given the well-documented challenges associated with 
attracting and installing adequate generating capacity in PJM.188 
 
184  
See id. at Section (f)(6)(D); see also Blazunas and Hammer Direct Joint Testimony at 23-24. 
185  
Id. at 24-25. 
186  
See SPP HILL Order at PP 64-66; see also id. (Rosner, Comm’r, concurring at PP 1, 3) (describing SPP’s 
HILL and HILLGA proposal as “pragmatic” and observing that, although the “mechanics” of SPP’s and PJM’s 
approaches are distinct, “the practical outcome is similar”). 
187  
See id. at PP 64-65, 67; see also id. at P 66 n.127 (explaining that, under FPA section 205, SPP “need not 
show that its proposal is the most just and reasonable among all possible alternatives so long as it demonstrates that 
the proposal is just and reasonable”) (citing Cities of Bethany v. FERC, 727 F.2d 1131, 1136 (D.C. Cir. 1984)). 
188  
Blazunas and Hammer Direct Joint Testimony at 24.

PDF page 41

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 41 
 
 
 
 
3. 
Allocations to Transmission Customers Are Recovered Through a 
Dedicated, Formula-Based Charge and Credited to Avoid Double 
Recovery. 
The PJM Transmission Owners’ proposal establishes the Interconnection Reliability 
Reinforcement Charge, which recovers each Transmission Owner’s annual transmission revenue 
requirement for the reinforcements it constructs and owns.189  The Transmission Provider assesses 
the charge to Firm Transmission Customers in each Zone based on the cost responsibility 
assignments determined through the proportional impact methodology described above.190  The 
charge rests on existing, Commission-accepted rates: each Transmission Owner’s revenue 
requirement for a reinforcement is determined under the formula rate in effect for its NITS and 
FCDS.191  The charge is recalculated annually to reflect revised billing determinants and posted 
by October 31 for the following calendar year, and charges to Point-To-Point customers are 
calculated monthly under Tariff, Part II, section 25.192  The Transmission Provider collects the 
charge monthly, in addition to all other transmission charges, and remits the revenues to the 
Transmission Owners that own the relevant IRRs.193  Importantly, application of the 
Interconnection Reliability Reinforcement Charge ensures that IRR costs are allocated only to 
those Zones containing service requests by an Eligible Customer on behalf of the applicable Large 
Load in a given cluster.  Zones with no Large Loads in a cluster will not be allocated any IRR 
costs.  
As discussed in the Blazunas and Hammer Direct Joint Testimony, this dedicated charge 
applies for 15 years after a reinforcement enters service.194  Beginning with the next full calendar 
year after the fifteenth year, the Transmission Provider assigns and recovers the remaining costs 
under sections (a) through (e) of Schedule 12.195  This transition is reasonable.  It confines cost 
responsibility to those Zones containing Large Load and generators whose modeled impacts 
contribute to  the need for reinforcements for a reasonable period that roughly corresponds with 
when it would be expected that some generators would be removed from service or otherwise 
retire, as well as the expectation of significant changes to the topology and use of the transmission 
system.  This 15-year period is also intended to account for what may be a transition or removal 
of certain Large Load facilities and thus their transmission service requests.  Although these 
timelines are, of course, inherently uncertain, the PJM Transmission Owners submit that 15 years 
is a reasonable estimate of when these various factors are likely to result in significant broadening 
of benefits to customers throughout PJM, rather than just the customers in the Zones in which 
 
189  
Id. at 25-29. 
190  
Proposed Schedule 12, Section (f)(3). 
191  
Id. at Section (f)(3)(A). 
192  
Proposed Schedule 12, Section (f)(3)(B)-(C). 
193  
Id. at Section (f)(4)(A)-(B). 
194  
Blazunas and Hammer Direct Joint Testimony at 27-29. 
195  
Proposed Schedule 12, Section (f)(3).

PDF page 42

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 42 
 
 
 
 
specific Large Loads are located.196  This mechanism also accounts for the fact that, after over a 
15-year period, broader dynamics of system use and benefit will evolve as economic patterns shift 
and technology changes, resulting in reliance by, and greater benefits to, loads other than the 
original large loads which gave rise to the upgrades.197  These shifts in benefits warrant application 
of the existing Transmission Enhancement Charge cost allocation methodologies, i.e., Solution-
based DFAX and, in the case of Regional Facilities, Load Ratio Share.198 
The proposal also ensures that no customer pays twice for the same facilities.  Because 
each Transmission Owner’s Firm Transmission Service rates under Attachment H already reflect 
its total cost of providing jurisdictional transmission service, including reinforcement costs, 
revenues from the Interconnection Reliability Reinforcement Charge are credited to Firm 
Transmission Customers in the Zone, and to Firm Point-To-Point customers delivering into the 
Zone, in proportion to their Demand Charges and Reserved Capacity, net of any applicable 
incentives.199  This is precisely the crediting mechanism the Show Cause Order contemplated.200  
It also mirrors the Commission’s reasoning in the Co-Located Load Paper Hearing Order, where 
the Commission explained that revenues from NFCDS will be credited against, and thus offset, 
the transmission revenue requirement on which firm transmission rates are based.201 
4. 
Transparency and Direct Wholesale Customer Commitments. 
In addition to the basic cost allocation and rate design features discussed above, the PJM 
Transmission Owners are committing to make, on compliance, necessary changes to their formula 
rate templates to: (1) provide transparency to state regulators and other interested parties regarding 
the costs of transmission facilities being constructed by the Transmission Owner to provide 
transmission service to Large Loads; and (2) adopt a mechanism designed to protect wholesale 
transmission customers not regulated at the retail level (e.g., municipals, cooperatives, and other 
applicable load-serving entities) from having to bear excessive large-load-related transmission 
upgrade costs.202     
With respect to transparency commitments, the Schedule 12 reporting requirements make 
the portfolio allocation results reviewable.  Following completion of the portfolio analysis, PJM 
will post the resulting cost responsibility assignments on its website.  Moreover, each applicable 
Transmission Owner also commits to make, within 120 days of a Commission order accepting this 
filing, a compliance filing to include any necessary additional provisions in its formula rate 
template to identify each transmission project such as IRRs that the Transmission Owner is 
constructing for purposes of providing transmission service to Large Load, along with a calculation 
 
196  
Id. at 27-29 and Exhibit No. PTO-0003. 
197  
Id. at 28-29 and Exhibit No. PTO-0003. 
198  
Id. at 26-27. 
199  
Proposed Schedule 12, Section (f)(5). 
200  
Show Cause Order at PP 3, 35. 
201  
Co-Located Load Paper Hearing Order at P 403. 
202  
Blazunas and Hammer Direct Joint Testimony at 29-31.

PDF page 43

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 43 
 
 
 
 
of the annual revenue requirement associated with such projects.203  This information will be 
substantially similar to information that the PJM Transmission Owners already provide in their 
formula rate templates with respect to projects planned through PJM’s RTEP that are allocated 
regionally through Transmission Enhancement Charges (“TEC”).  These additions will serve three 
purposes.  First, they will allow PJM to allocate and invoice Interconnection Reliability 
Reinforcement Charges, which as discussed above will be the mechanism whereby PJM collects 
amounts allocated to Responsible Customers in Zones outside of the Zones in which the IRRs are 
constructed.  Second, in conjunction with the cost responsibility assignments posted by PJM, they 
will satisfy the Commission’s preliminary findings in the Show Cause Order with respect to 
providing transparency regarding the costs associated with transmission upgrades driven by Large 
Load additions.204  Third, by providing this level of cost transparency, state commissions and other 
retail regulators will have access to information to assist them if they choose to allocate some 
amount of transmission rate costs specifically to Large Load customers in their jurisdiction.205  
Additionally, each applicable PJM Transmission Owner commits to include in the above-
referenced compliance filing a surcharge/crediting mechanism designed to protect direct wholesale 
transmission customers in its zone, where applicable, from having to bear disproportionate large-
load-related system upgrade costs.206  These wholesale customers would include municipal 
utilities and electric cooperatives that are not regulated by states and, therefore, cannot be insulated 
by state action against bearing a potentially disproportionate amount of costs associated with 
reinforcements necessary to provide transmission service to Large Load.  The purpose of this 
commitment, and resulting mechanisms, is to ensure that wholesale customers are protected from 
having to bear a share of Large Load-related costs in a situation where there are no Large Loads, 
or relatively fewer Large Loads, in their service areas requesting service in a given PJM study 
cycle.  Where a wholesale customer has Large Load customers that request and are granted 
transmission service through PJM, this mechanism would result in both credits and surcharges, 
since the wholesale customer should bear the cost responsibilities of the upgrades that come out 
of a particular cycle at PJM.   
 The PJM Transmission Owners have deliberately avoided specifying a single mechanism 
for implementing this commitment due to the need for flexibility so that Transmission Owners can 
design and propose wholesale customer protection mechanisms that are consistent with their own 
individual circumstances, including any applicable retail allocation or charge mechanisms.207  One 
potential approach involves a surcharge/credit approach pursuant to which a Transmission Owner 
would calculate, in addition to its total NITS revenue requirement, a revenue requirement specific 
 
203  
Information regarding all transmission projects, including IRRs, Supplemental Projects, and RTEP projects, 
will continue to be posted and maintained on the project status and cost allocation page of PJM’s website, located at: 
https://www.pjm.com/planning/m/project-construction. 
204  
Show Cause Order at P 66. 
205  
This information will be provided by each individual Transmission Owner based on the IRRs it is 
constructing, which will assist in facilitating retail regulators within multi-Transmission Owner Zones to allocate costs 
relevant to retail customers within their states.  
206  
Blazunas and Hammer Direct Joint Testimony at 29-30. 
207  
Id. at 30-31.

PDF page 44

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 44 
 
 
 
 
to large load-driven upgrades.  Using that information, a credit would be calculated and provided 
to wholesale transmission customers to the extent they do not have Large Load customers, or 
relatively fewer Large Load customers, driving the upgrades in a specific cluster, based on their 
pro rata share of overall NITS load.  The credit would be funded by the large loads (specifically, 
the Electric Distribution Company/Load Serving Entity representing those Large Loads) with 
relatively greater Large Load customers in a cluster through a surcharge to those entities.  
Regardless, the PJM Transmission Owners commit to include their proposed direct wholesale 
customer protection mechanisms in the compliance filings. 
5. 
Schedule 12, Section (f) Produces Just and Reasonable Rates and is 
not Unduly Discriminatory or Preferential. 
The proposed tariff revisions in Schedule 12, Section (f) satisfy the just and reasonable 
standard of FPA section 205 because they align cost responsibility with cost causation and benefits 
at every step.  The Commission identified the central risk in this proceeding as the shifting of large 
load-driven transmission costs onto “other transmission customers that neither caused the need for 
nor benefit commensurately from those Network Upgrades.”208  The Commission further observed 
that, when Network Upgrade costs are rolled into a Transmission Owner’s revenue requirement, 
transmission customers other than the Eligible Customer may bear a portion of those costs.209  As 
discussed above, the PJM Transmission Owners’ proposal addresses these concerns through a 
combination of the proportional impact methodology, 15-year cost allocation transition 
mechanism, and the assessment and crediting of the Interconnection Reliability Reinforcement and 
Generator Reliability Recovery Fees.  These provisions will work in tandem with the proposed 
CRA or similar agreements to protect against the risk of shifting costs to transmission customers 
for facilities from which they receive no benefit.210 
The resulting rates are also cost-based and verifiable.  Every input to the charge and the 
fee, from the revenue requirement to the cost of capital, comes from Transmission Owner formula 
rates already on file with the Commission, and annual recalculation and public posting keep the 
charges current and transparent.211  The Commission therefore has a clear basis on which to find 
that proposed Schedule 12, Section (f) yields just and reasonable rates. 
Section (f) appropriately distinguishes between generation and Large Load-related 
transmission service requests while providing a consistent basis for measuring their respective 
contributions to the need for IRRs.  Requests included in the same Cycle are evaluated using the 
same distribution factor-based methodology, thresholds, and weighting rules, ensuring that their 
relative electrical impacts are measured on a consistent basis.212  That common measurement does 
not, however, equate generation and Large Load customers for rate design purposes.  Rather, the 
 
208  
Show Cause Order at P 81. 
209  
Id. at P 61. 
210  
Proposed Schedule 12, Sections (f)(1), (f)(2)(C), (f)(3), (f)(5). 
211  
Id. at Sections (f)(2)(D), (f)(3)(A)-(B). 
212  
Id. at Section (f)(2)(A)-(C).

PDF page 45

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 45 
 
 
 
 
proposed tariff provisions assign and recover the resulting costs consistent with longstanding rate 
structures while accounting for the portfolio nature of IRRs that will be identified in PJM’s Fast 
Energization Process: IRRs will be rolled into Zonal transmission rates and recovered from 
transmission customers through the Interconnection Reliability Reinforcement Charge, while 
Generator Interconnection Customers bear a fair share of IRR costs through the Generator 
Reliability Reinforcement Fee.213  The proposal thus distinguishes between generation and load 
where their differing circumstances warrant different rate treatment, while applying a consistent 
cost causation methodology to determine their respective contributions to the IRRs. 
Section (f) also resolves a potential source of discrimination the Commission identified in 
the Co-Located Load Paper Hearing Order.  There, the Commission found that the lack of clear 
tariff provisions led to disparate treatment because Transmission Owners took different approaches 
and created the risk that costs would not be allocated consistent with cost causation principles.214  
Section (f) adopts a uniform rule applied across the PJM region.  At the same time, Section (f) 
confines itself to Commission-jurisdictional transmission rates, which the Commission has found 
are directly affected by the costs of upgrades needed to serve Large Loads,215 and it leaves 
undisturbed state ratepayer protections such as state-jurisdictional Large Load tariffs.216 
For these reasons, the Commission should find that proposed revisions to Section (f) of 
Schedule 12 are just and reasonable and not unduly discriminatory or preferential and they satisfy 
the Show Cause Order’s directives regarding cost transparency, mitigation of cost shifting among 
transmission customers, and the crediting of Large Load payments toward transmission revenue 
requirements. 
IV. 
EFFECTIVE DATE AND IMPLEMENTATION 
The PJM Transmission Owners understand that PJM intends to request an effective date of 
March 16, 2027 for the proposed revisions to Parts I, III, VI, VII, IX, XI, Attachment F-3, 
Attachment F-3A, Attachment F-4, and certain parts of Part VIII to the Tariff.  For the remaining 
Part VIII revisions associated with the Fast Energization Process, PJM intends to request an 
indeterminate effective date of 12/31/9998, rather than the effective date requested in its August 
17 Compliance Filing (for which PJM requested a March 16, 2027 effective date).  The PJM 
Transmission Owners further understand that PJM intends to request a 60-day comment period for 
its companion filing.   
Accordingly, given the interrelated nature of the filings, the PJM Transmission Owners 
request an effective date of March 16, 2027 for their proposed revisions to Tariff, Part XI and 
Schedules 20, 21, and 22, and an effective date of 12/31/9998 for the proposed pro forma CRA 
(Part IX, Subpart P); Tariff, Part VIII, Subpart N, section 441; and Schedule 12 revisions proposed 
 
213  
Id. at Sections (f)(2)(C)(1)-(2), (f)(4), and (f)(6). 
214  
Co-Located Load Paper Hearing Order at P 59. 
215  
Show Cause Order at P 68. 
216  
Id. at n.175.

PDF page 46

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 46 
 
 
 
 
in this filing.  The PJM Transmission Owners also request that the Commission establish the same 
comment date for the instant filing that it establishes for PJM’s filing. 
To the extent that implementation of a particular provision proposed by the PJM 
Transmission Owners depends on a service, process, definition, or study output proposed in PJM’s 
companion filing, the PJM Transmission Owners request coordinated implementation of the 
corresponding provisions.  Such coordination would be limited to provisions that are operational 
dependent on PJM’s proposal and would not affect the independent basis for accepting the 
remaining PJM Transmission Owner provisions under section 205. 
If the Commission modifies or rejects a provision in PJM’s companion filing on which an 
otherwise acceptable PJM Transmission Owner provision depends, the PJM Transmission Owners 
request leave to submit any limited conforming revisions necessary to implement the 
Commission’s determinations. 
V. 
ADDITIONAL FILING INFORMATION 
A. 
Request for Waiver. 
To the extent necessary, the PJM Transmission Owners request waiver of the requirement 
to submit the cost of service data required by 18 C.F.R. § 35.13.  Moreover, the information 
submitted with this filing substantially complies with the requirements of Part 35 of the 
Commission’s regulations applicable to filings of this type.  The PJM Transmission Owners 
request waiver of any applicable requirement of Part 35 for which a waiver is not specifically 
requested, as necessary, in order to permit this filing to become effective as proposed. 
B. 
Documents Submitted With This Filing. 
The PJM Transmission Owners submit the following materials: 
1. Attachment A: Clean Tariff Records 
2. Attachment B: Marked Tariff Records 
3. Exhibit No. PTO-0001: Direct Joint Testimony of Peter Blazunas and Hanhan Hammer 
4. Exhibit No. PTO-0002: Professional Backgrounds and Experience 
5. Exhibit No. PTO-0003: Support for 15-year Allocation Period

PDF page 47

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 47 
 
 
 
 
C. 
Communications. 
Communications regarding this filing should be addressed to the following individuals, 
whose names should be entered on the official service list maintained by the Secretary for this 
proceeding: 
Pulin Shah  
Vice President, Transmission 
Development 
EXELON CORPORATION 
2301 Market Street  
Philadelphia, PA 19103   
Pulin.Shah@exeloncorp.com 
Chair of the Transmission Owners 
Agreement Administrative Committee 
 
 
 
Alejandro Bautista 
Assistant General Counsel 
EXELON CORPORATION 
2301 Market Street 
Philadelphia, PA 19103  
Alejandro.Bautista@exeloncorp.com 
Michael Kunselman  
Richard P. Sparling 
Jonathan A. Namazi 
Margaret Smilowitz 
Davis Wright Tremaine LLP 
1301 K Street NW  
Suite 500 East  
Washington, DC 20005 
michaelkunselman@dwt.com 
ricksparling@dwt.com 
jonathannamazi@dwt.com 
margaretsmilowitz@dwt.com 
 
D. 
Service. 
 
PJM has served a copy of this filing on all PJM Members and on all state utility regulatory 
commissions in the PJM Region by posting this filing electronically.  In accordance with the 
Commission’s regulations,217 PJM will post a copy of this filing to the FERC filings section of its 
internet site, https://www.pjm.com/library/filing-order, and will send an e-mail on the same date 
as this filing to all PJM Members and all state utility regulatory commissions in the PJM Region,218 
alerting them that this filing has been made by PJM and is available by following such link.  If the 
document is not immediately available by using the referenced link, the document will be available 
through the referenced link within 24 hours of the filing.  Also, a copy of this filing will be available 
on the Commission’s eLibrary website located at the following link: http://www.ferc.gov/docs-
filing/elibrary.asp in accordance with the Commission’s regulations and Order No. 714. 
 
 
 
 
217  
See 18 C.F.R §§ 35.2(e) and 385.2010(f)(3). 
218  
PJM already maintains, updates, and regularly uses e-mail lists for all PJM members and affected state 
commissions.

PDF page 48

Honorable Debbie-Anne A. Reese 
November 16, 2026 
Page 48 
 
 
 
 
VI. 
CONCLUSION 
 
 
For the reasons stated herein, the PJM Transmission Owners respectfully request that the 
Commission accept the Tariff revisions without hearing, modification or condition.  
 
 
 
 
 
 
 
Respectfully submitted, 
 
 
 
/s/ Michael Kunselman 
Michael Kunselman 
Richard P. Sparling  
Jonathan A. Namazi 
Margaret Smilowitz 
Davis Wright Tremaine LLP  
1301 K Street NW  
Suite 500 East  
Washington, DC 20005 
 
 
 
 
 
 
 
 
 
 
 
Attorneys for The FirstEnergy  
 
 
 
 
 
 
 
 Transmission Companies 
 
 
 
 
 
 
 
 
On behalf of the PJM Transmission Owners

PDF page 49

Attachment A 
Revisions to the  
PJM Open Access Transmission Tariff  
(Clean Format) 
Page 1

PDF page 50

Definitions – R - S
Ramping Capability:
“Ramping Capability” shall mean the sustained rate of change of generator output, in megawatts 
per minute.
Real-time Congestion Price:
“Real-time Congestion Price” shall mean the Congestion Price resulting from the Office of the 
Interconnection’s dispatch of the PJM Interchange Energy Market in the Operating Day.
Real-time Loss Price:
“Real-time Loss Price” shall mean the Loss Price resulting from the Office of the 
Interconnection’s dispatch of the PJM Interchange Energy Market in the Operating Day.
Real-time Energy Market:
“Real-time Energy Market” shall mean the purchase or sale of energy and payment of 
Transmission Congestion Charges for quantity deviations from the Day-ahead Energy Market in 
the Operating Day.
Real-time Offer:
“Real-time Offer” shall mean a new offer or an update to a Market Seller’s existing cost-based or 
market-based offer for a clock hour, submitted for use after the close of the Day-ahead Energy 
Market.
Real-time Prices:
“Real-time Prices” shall mean the Locational Marginal Prices resulting from the Office of the 
Interconnection’s dispatch of the PJM Interchange Energy Market in the Operating Day.
Real-time Settlement Interval:
“Real-time Settlement Interval” shall mean the interval used by settlements, which shall be every 
five minutes.
Real-time System Energy Price:
“Real-time System Energy Price” shall mean the System Energy Price resulting from the Office 
of the Interconnection’s dispatch of the PJM Interchange Energy Market in the Operating Day.
Reasonable Efforts:
Page 2

PDF page 51

“Reasonable Efforts” shall mean, with respect to any action required to be made, attempted, or 
taken by an Interconnection Party or by a Construction Party under Tariff, Part IV or Part VI, an 
Interconnection Service Agreement, or a Construction Service Agreement, such efforts as are 
timely and consistent with Good Utility Practice and with efforts that such party would undertake 
for the protection of its own interests.
Receiving Party:
“Receiving Party” shall mean the entity receiving the capacity and energy transmitted by the 
Transmission Provider to Point(s) of Delivery.
Referral:
“Referral” shall mean a formal report of the Market Monitoring Unit to the Commission for 
investigation of behavior of a Market Participant, of behavior of PJM, or of a market design 
flaw, pursuant to Tariff, Attachment M, section IV.I.
Reference Resource:
“Reference Resource” shall mean a combustion turbine generating station, configured with a 
single General Electric Frame 7HA turbine with evaporative cooling, Selective Catalytic 
Reduction technology all CONE Areas, dual fuel capability, and a heat rate of 9.134 Mmbtu/ 
MWh. 
Regional Entity:
“Regional Entity” shall have the same meaning specified in the Operating Agreement.
Regional Transmission Expansion Plan:
“Regional Transmission Expansion Plan” shall mean the plan prepared by the Office of the 
Interconnection pursuant to Operating Agreement, Schedule 6 for the enhancement and 
expansion of the Transmission System in order to meet the demands for firm transmission 
service in the PJM Region.
Regional Transmission Group (RTG):
“Regional Transmission Group” or “RTG” shall mean a voluntary organization of transmission 
owners, transmission users and other entities approved by the Commission to efficiently 
coordinate transmission planning (and expansion), operation and use on a regional (and 
interregional) basis.
Regulation:
“Regulation” shall mean the capability of a specific generation resource or Demand Resource 
with appropriate telecommunications, control and response capability to separately increase and 
Page 3

PDF page 52

decrease its output or adjust load in response to a regulating control signal, in accordance with 
the specifications in the PJM Manuals.  Regulation is inclusive of Regulation-Down Service and 
Regulation-Up Service.
Regulation-Down Requirement:
“Regulation-Down Requirement” shall mean the required megawatts of performance-adjusted 
Regulation-Down Service capability to be maintained in a Regulation Zone. The Regulation-
Down Requirement is defined as a set megawatt value by hour in accordance with the PJM 
Manuals, and can increase to account for additional operational uncertainty.
Regulation-Down Service
“Regulation-Down Service” shall mean the capability of a specific generation resource or 
Demand Resource with appropriate telecommunications and response capability to increase and 
decrease its output in the downward range from a set point or adjust load in response to a 
regulating-down control signal, in accordance with the specification in the PJM Manuals.
Regulation-Up Requirement:
“Regulation-Up Requirement” shall mean the required megawatts of performance-adjusted
Regulation-Up Service capability to be maintained in a Regulation Zone. The Regulation-Up
Requirement is defined as a set megawatt value by hour in accordance with the PJM Manuals,
and can increase to account for additional operational uncertainty.
Regulation-Up Service
“Regulation-Up Service” shall mean the capability of a specific generation resource or Demand
Resource with appropriate telecommunications and response capability to increase and decrease
its output in the upward range from a set point or adjust load in response to a regulating-up
control signal, in accordance with the specification in the PJM Manuals.
Regulation Zone:
“Regulation Zone” shall mean any of those one or more geographic areas, each consisting of a 
combination of one or more Control Zone(s) as designated by the Office of the Interconnection 
in the PJM Manuals, relevant to provision of, and requirements for, regulation service.
Relevant Electric Retail Regulatory Authority:
“Relevant Electric Retail Regulatory Authority” shall mean an entity that has jurisdiction over 
and establishes prices and policies for competition for providers of retail electric service to end-
customers, such as the city council for a municipal utility, the governing board of a cooperative 
utility, the state public utility commission or any other such entity.
Reliability Assurance Agreement or PJM Reliability Assurance Agreement:
Page 4

PDF page 53

“Reliability Assurance Agreement” or “PJM Reliability Assurance Agreement” shall mean that 
certain Reliability Assurance Agreement Among Load Serving Entities in the PJM Region, on 
file with FERC as PJM Interconnection L.L.C. Rate Schedule FERC No. 44, and as amended 
from time to time thereafter.
Reliability Pricing Model Auction:
“Reliability Pricing Model Auction” or “RPM Auction” shall mean the Base Residual Auction or 
any Incremental Auction, or, for the 2016/2017 and 2017/2018 Delivery Years, any Capacity 
Performance Transition Incremental Auction.
Required Transmission Enhancements:
“Regional Transmission Enhancements” shall mean enhancements and expansions of the 
Transmission System that (1) a Regional Transmission Expansion Plan developed pursuant to 
Operating Agreement, Schedule 6 or (2) any joint planning or coordination agreement between 
PJM and another region or transmission planning authority set forth in Tariff, Schedule 12-
Appendix B (“Appendix B Agreement”) designates one or more of the Transmission Owner(s) to 
construct and own or finance.  Required Transmission Enhancements shall also include 
enhancements and expansions of facilities in another region or planning authority that meet the 
definition of transmission facilities pursuant to FERC’s Uniform System of Accounts or have 
been classified as transmission facilities in a ruling by FERC addressing such facilities 
constructed pursuant to an Appendix B Agreement cost responsibility for which has been 
assigned at least in part to PJM pursuant to such Appendix B Agreement. 
Reserved Capacity:
“Reserved Capacity” shall mean the maximum amount of capacity and energy that the 
Transmission Provider agrees to transmit for the Transmission Customer over the Transmission 
Provider’s Transmission System between the Point(s) of Receipt and the Point(s) of Delivery 
under Tariff, Part II.  Reserved Capacity shall be expressed in terms of whole megawatts on a 
sixty (60) minute interval (commencing on the clock hour) basis.
Reserve Penalty Factor:
“Reserve Penalty Factor” shall mean the cost, in $/MWh, associated with being unable to meet a 
specific reserve requirement in a Reserve Zone or Reserve Sub-zone.  A Reserve Penalty Factor 
will be defined for each reserve requirement in a Reserve Zone or Reserve Sub-zone.
Reserve Sub-zone:
“Reserve Sub-zone” shall mean any of those geographic areas wholly contained within a Reserve 
Zone, consisting of a combination of a portion of one or more Control Zone(s) as designated by 
the Office of the Interconnection in the PJM Manuals, relevant to provision of, and requirements 
for, reserve service.
Page 5

PDF page 54

Reserve Zone:
“Reserve Zone” shall mean any of those geographic areas consisting of a combination of one or 
more Control Zone(s), as designated by the Office of the Interconnection in the PJM Manuals, 
relevant to provision of, and requirements for, reserve service.
Residual Auction Revenue Rights:
“Residual Auction Revenue Rights” shall mean incremental stage 1 Auction Revenue Rights 
created within a Planning Period by an increase in transmission system capability, including the 
return to service of existing transmission capability, that was not modeled pursuant to Operating 
Agreement, Schedule 1, section 7.5 and the parallel provisions of  Tariff, Attachment K-
Appendix, section 7.5 in compliance with Operating Agreement, Schedule 1, section 7.4.2 (h) 
and the parallel provisions of Tariff, Attachment K-Appendix, section 7.4.2(h), and, if modeled, 
would have increased the amount of stage 1 Auction Revenue Rights allocated pursuant to 
Operating Agreement, Schedule 1, section 7.4.2 and the parallel provisions of Tariff, Attachment 
K-Appendix, section 7.4.2; provided that, the foregoing notwithstanding, Residual Auction 
Revenue Rights shall exclude: 1) Incremental Auction Revenue Rights allocated pursuant to 
Tariff, Part VI;  and 2) Auction Revenue Rights allocated to entities that are assigned cost 
responsibility pursuant to Operating Agreement, Schedule 6 for  transmission upgrades that 
create such rights.
Residual Metered Load:
“Residual Metered Load” shall mean all load remaining in an electric distribution company’s 
fully metered franchise area(s) or service territory(ies) after all nodally priced load of entities 
serving load in such area(s) or territory(ies) has been carved out.
Resource Substitution Charge:
“Resource Substitution Charge” shall mean a charge assessed on Capacity Market Buyers in an 
Incremental Auction to recover the cost of replacement Capacity Resources.
Responsible Customer: 
“Responsible Customer” shall mean customers using Interim Network Integration Transmission 
Service, Firm Contract Demand Transmission Service, Non-Firm Contract Demand 
Transmission Service, Point-to-Point Transmission Service and/or Network Integration 
Transmission Service and Merchant Transmission Facility owners, which are assigned cost 
responsibility for Transmission Enhancement Charges as determined pursuant to Tariff, 
Schedule 12.
Revenue Data for Settlements:
Page 6

PDF page 55

“Revenue Data for Settlements” shall mean energy quantities used in accounting and billing as 
determined pursuant to Tariff, Attachment K-Appendix and the corresponding provisions of 
Operating Agreement, Schedule 1.
RPM Seller Credit:
“RPM Seller Credit” shall mean an additional form of Unsecured Credit defined in Tariff, 
Attachment Q, section IV.
Scheduled Incremental Auctions:
“Scheduled Incremental Auctions” shall refer to the First, Second, or Third Incremental Auction.
Schedule of Work:
“Schedule of Work” shall mean that schedule attached to the Interconnection Construction 
Service Agreement setting forth the timing of work to be performed by the Constructing Entity 
pursuant to the Interconnection Construction Service Agreement, based upon the Facilities Study 
and subject to modification, as required, in accordance with Transmission Provider’s scope 
change process for interconnection projects set forth in the PJM Manuals.
Scope of Work:
“Scope of Work” shall mean that scope of the work attached as a schedule to the Interconnection 
Construction Service Agreement and to be performed by the Constructing Entity(ies) pursuant to 
the Interconnection Construction Service Agreement, provided that such Scope of Work may be 
modified, as required, in accordance with Transmission Provider’s scope change process for 
interconnection projects set forth in the PJM Manuals.
Seasonal Capacity Performance Resource:
“Seasonal Capacity Performance Resource” shall have the same meaning specified in Tariff, 
Attachment DD, section 5.5A.
Seasonal Facility Rating:
“Seasonal Facility Rating” shall mean a Transmission Facility Rating that:  
(a) Applies to a specified season, where seasons are defined by the Office of the Interconnection 
to include not fewer than four seasons in each year, and to reasonably reflect portions of the year 
where expected high temperatures are relatively consistent.
(b) Reflects an up-to-date forecast of ambient air temperature across the relevant season over 
which the rating applies.
Page 7

PDF page 56

(c) Is evaluated annually, if not more frequently, for each season in the future for which 
Transmission Service can be requested
Secondary Reserve: 
“Secondary Reserve” shall mean the reserve capability of generation resources that can be 
converted fully into energy or Economic Load Response Participant resources whose demand 
can be reduced within 30 minutes (less the capability of such resources to provide Primary 
Reserve), from the request of the Office of the Interconnection, regardless of whether the 
equipment providing the reserve is electrically synchronized to the Transmission System or not.
Secondary Systems:
“Secondary Systems” shall mean control or power circuits that operate below 600 volts, AC or 
DC, including, but not limited to, any hardware, control or protective devices, cables, 
conductors, electric raceways, secondary equipment panels, transducers, batteries, chargers, and 
voltage and current transformers.
Second Incremental Auction:
“Second Incremental Auction” shall mean an Incremental Auction conducted ten months before 
the Delivery Year to which it relates.  
Security:
“Security” shall mean the security provided by the New Service Customer pursuant to Tariff, 
section 212.4 or Tariff, Part VI, section 213.4 to secure the New Service Customer’s 
responsibility for Costs under the Interconnection Service Agreement or Upgrade Construction 
Service Agreement and Tariff, Part VI, section 217. 
Segment:
“Segment” shall have the same meaning as described in Operating Agreement, Schedule 1, 
section 3.2.3(e).
Self-Supply:
“Self-Supply” shall mean Capacity Resources secured by a Load-Serving Entity, by ownership 
or contract, outside a Reliability Pricing Model Auction, and used to meet obligations under this 
Attachment or the Reliability Assurance Agreement through submission in a Base Residual 
Auction or an Incremental Auction of a Sell Offer indicating such Market Seller’s intent that 
such Capacity Resource be Self-Supply.  Self-Supply may be either committed regardless of 
clearing price or submitted as a Sell Offer with a price bid. A Load Serving Entity's Sell Offer 
with a price bid for an owned or contracted Capacity Resource shall not be deemed “Self-
Supply,” unless it is designated as Self-Supply and used by the LSE to meet obligations under 
this Attachment or the Reliability Assurance Agreement.
Page 8

PDF page 57

Self-Supply Entity:
“Self-Supply Entity” shall mean the following types of Load Serving Entity that operate under 
long-standing business models: single customer entity, public power entity, or vertically 
integrated utility, where “vertically integrated utility” means a utility that owns generation, 
includes such generation in its regulated rates, and earns a regulated return on its investment in 
such generation or receives any cost recovery for such generation through bilateral contracts; 
“single customer entity”  means a Load Serving Entity that serves at retail only customers that 
are under common control with such Load Serving Entity, where such control means holding 
51% or more of the voting securities or voting interests of the Load Serving Entity and all its 
retail customers; and “public power entity” means cooperative and municipal utilities, including 
public power supply entities comprised of either or both of the same and rural electric 
cooperatives, and joint action agencies.
Self-Supply Seller:
“Self-Supply Seller” shall mean, for purposes of evaluating Buyer-Side Market Power, the 
following types of Load Serving Entities that operate under long-standing business models: 
vertically integrated utility or public power entity, where “vertically integrated utility” means a 
utility that owns generation, includes such generation in its state-regulated rates, and earns a 
state-regulated return on its investment in such generation; and “public power entity” means 
electric cooperatives that are either rate regulated by the state or have their long-term resource 
plan approved or otherwise reviewed and accepted by a Relevant Electric Retail Regulatory 
Authority and municipal utilities or joint action agencies that are subject to direct regulation by a 
Relevant Electric Retail Regulatory Authority.
Sell Offer:
“Sell Offer” shall mean an offer to sell Capacity Resources in a Base Residual Auction, 
Incremental Auction, or Reliability Backstop Auction.
Service Agreement:
“Service Agreement” shall mean the initial agreement and any amendments or supplements 
thereto entered into by the Transmission Customer and the Transmission Provider for service 
under the Tariff.
Service Commencement Date:
“Service Commencement Date” shall mean the date the Transmission Provider begins to provide 
service pursuant to the terms of an executed Service Agreement, or the date the Transmission 
Provider begins to provide service in accordance with Tariff, Part II, section 15.3 or Tariff, Part 
III, section 29.1.
Short-Term Firm Point-To-Point Transmission Service:
Page 9

PDF page 58

“Short-Term Firm Point-To-Point Transmission Service” shall mean Firm Point-To-Point 
Transmission Service under Tariff, Part II with a term of less than one year.
Short-term Project:
“Short-term Project” shall have the same meaning provided in the Operating Agreement.
Short-Term Resource Procurement Target:
“Short-Term Resource Procurement Target” shall mean, for Delivery Years through May 31, 
2018, as to the PJM Region, for purposes of the Base Residual Auction, 2.5% of the PJM Region 
Reliability Requirement determined for such Base Residual Auction,  for purposes of the First 
Incremental Auction, 2% of the of the PJM Region Reliability Requirement as calculated at the 
time of the Base Residual Auction; and, for purposes of the Second Incremental Auction, 1.5% 
of the of the PJM Region Reliability Requirement as calculated at the time of the Base Residual 
Auction; and, as to any Zone, an allocation of the PJM Region Short-Term Resource 
Procurement Target based on the Preliminary Zonal Forecast Peak Load, reduced by the amount 
of load served under the FRR Alternative.  For any LDA, the LDA Short-Term Resource 
Procurement Target shall be the sum of the Short-Term Resource Procurement Targets of all 
Zones in the LDA.
Short-Term Resource Procurement Target Applicable Share:
“Short-Term Resource Procurement Target Applicable Share” shall mean, for Delivery Years 
through May 31, 2018: (i) for the PJM Region, as to the First and Second Incremental Auctions, 
0.2 times the Short-Term Resource Procurement Target used in the Base Residual Auction and, 
as to the Third Incremental Auction for the PJM Region, 0.6 times such target; and (ii) for an 
LDA, as to the First and Second Incremental Auctions, 0.2 times the Short-Term Resource 
Procurement Target used in the Base Residual Auction for such LDA and, as to the Third 
Incremental Auction, 0.6 times such target. 
Site:
“Site” shall mean all of the real property, including but not limited to any leased real property 
and easements, on which the Customer Facility is situated and/or on which the Customer 
Interconnection Facilities are to be located.
Small Commercial Customer:
“Small Commercial Customer,” as used in RAA, Schedule 6 and Tariff, Attachment DD-1, shall 
mean a commercial retail electric end-use customer of an electric distribution company that 
participates in a mass market demand response program under the jurisdiction of a RERRA and 
satisfies the definition of a “small commercial customer” under the terms of the applicable 
RERRA’s program, provided that the customer has an annual peak demand no greater than 
100kW.
Page 10

PDF page 59

Small Generation Resource:
“Small Generation Resource” shall mean an Interconnection Customer’s device of 20 MW or 
less for the production and/or storage for later injection of electricity identified in an 
Interconnection Request, but shall not include the Interconnection Customer’s Interconnection 
Facilities.  This term shall include Energy Storage Resources and/or other devices for storage for 
later injection of energy.
Small Inverter Facility:
“Small Inverter Facility” shall mean an Energy Resource that is a certified small inverter-based 
facility no larger than 10 kW.
Small Inverter ISA:
“Small Inverter ISA” shall mean an agreement among Transmission Provider, Interconnection 
Customer, and Interconnected Transmission Owner regarding interconnection of a Small Inverter 
Facility under Tariff, Part IV, section 112B.
Special Member:
“Special Member” shall mean an entity that satisfies the requirements of Operating Agreement, 
Schedule 1, section 1.5A.02, and the parallel provisions of Tariff, Attachment K-Appendix, 
section 1.5A.02, or the special membership provisions established under the Emergency Load 
Response and Pre-Emergency Load Response Programs.
Spot Market Backup:
“Spot Market Backup” shall mean the purchase of energy from, or the delivery of energy to, the 
PJM Interchange Energy Market in quantities sufficient to complete the delivery or receipt 
obligations of a bilateral contract that has been curtailed or interrupted for any reason.
Spot Market Energy:
“Spot Market Energy” shall mean energy bought or sold by Market Participants through the PJM 
Interchange Energy Market at System Energy Prices determined as specified in Operating 
Agreement, Schedule 1, section 2, and the parallel provisions of Tariff, Attachment K-Appendix, 
section 2.
Start Additional Labor Costs:
“Start Additional Labor Costs” shall mean additional labor costs for startup required above 
normal station manning levels. 
Start Fuel:
Page 11

PDF page 60

For units without a soak process, “Start Fuel” shall consist of fuel consumed from first fire of the 
start process to first breaker closing, plus any fuel expended from last breaker opening to 
shutdown.
For units with a soak process, “Start Fuel” is fuel consumed from first fire of the start process 
(initial reactor criticality for nuclear units) to dispatchable output (including auxiliary boiler 
fuel), plus any fuel expended from last breaker opening to shutdown, excluding normal plant 
heating/auxiliary equipment fuel requirements.  Start Fuel included for each temperature state 
from breaker closure to dispatchable output shall not exceed the unit specific soak time period 
reviewed and approved as part of the unit-specific parameter process detailed in Tariff, 
Attachment K-Appendix, section 6.6(c) or the defaults below:
•
Cold Soak Time = 0.73 * unit specific Minimum Run Time (in hours)
•
Intermediate Soak Time = 0.61 * unit specific Minimum Run Time (in hours)
•
Hot Soak Time = 0.43 * unit specific Minimum Run Time (in hours)  
Start-Up Costs:
“Start-Up Costs” shall consist primarily of the cost of fuel, as determined by the unit’s start heat 
input (adjusted by the performance factor) times the fuel cost.  It also includes operating costs, 
Maintenance Adders, emissions allowances/adders, and station service cost.  Start-Up Costs can 
vary with the unit offline time being categorized in three unit temperature conditions: hot, 
intermediate and cold.
For units with a steam turbine and a soak process (nuclear, steam, and combined cycle), “Start 
Fuel” is fuel consumed from first fire of start process (initial reactor criticality for nuclear units): 
Start-Up Costs shall mean the net unit costs from PJM’s notification to the level at which the unit 
can follow PJM’s dispatch, and from last breaker open to shutdown.
For units without a steam turbine and no soak process (engines, combustion turbines, 
Intermittent Resources, and Energy Storage Resources): Start-Up Costs shall mean the unit costs 
from PJM’s notification to first breaker close and from last breaker open to shutdown.  
State:
“State” shall mean the District of Columbia and any State or Commonwealth of the United 
States.
State Commission:
“State Commission” shall mean any state regulatory agency having jurisdiction over retail 
electricity sales in any State in the PJM Region.
State Estimator:
Page 12

PDF page 61

“State Estimator” shall mean the computer model of power flows specified in Operating 
Agreement, Schedule 1, section 2.3 and the parallel provisions of Tariff, Attachment K-
Appendix, section 2.3.
State Subsidy:
“State Subsidy” shall mean a direct or indirect payment, concession, rebate, subsidy, non-
bypassable consumer charge, or other financial benefit that is as a result of any action, mandated 
process, or sponsored process of a state government, a political subdivision or agency of a state, 
or an electric cooperative formed pursuant to state law, and that 
(1) is derived from or connected to the procurement of (a) electricity or electric 
generation capacity sold at wholesale in interstate commerce, or (b) an attribute of the 
generation process for electricity or electric generation capacity sold at wholesale in 
interstate commerce; or
(2) will support the construction, development, or operation of a new or existing Capacity 
Resource; or 
(3) could have the effect of allowing the unit to clear in any PJM capacity auction. 
Notwithstanding the foregoing, State Subsidy shall not include (a) payments, concessions, 
rebates, subsidies, or incentives designed to incent, or participation in a program, contract or 
other arrangement that utilizes criteria designed to incent or promote, general industrial 
development in an area or designed to incent siting facilities in that county or locality rather than 
another county or locality; (b) state action that imposes a tax or assesses a charge utilizing the 
parameters of a regional program on a given set of resources notwithstanding the tax or cost 
having indirect benefits on resources not subject to the tax or cost (e.g., Regional Greenhouse 
Gas Initiative); (c) any indirect benefits to a Capacity Resource as a result of any transmission 
project approved as part of the Regional Transmission Expansion Plan; (d) any contract, legally 
enforceable obligation, or rate pursuant to the Public Utility Regulatory Policies Act or any other 
state-administered federal regulatory program (e.g., the Cross-State Air Pollution Rule); (e) any 
revenues from the sale or allocation, either direct or indirect, to an Entity Providing Supply 
Services to Default Retail Service Provider where such entity’s obligations was awarded through 
a state default procurement auction that was subject to independent oversight by a consultant or 
manager who certifies that the auction was conducted through a non-discriminatory and 
competitive bidding process, subject to the below condition, and provided further that nothing 
herein would exempt a Capacity Resource that would otherwise be subject to the minimum offer 
price rule pursuant to this Tariff; (f) any revenues for providing capacity as part of an FRR 
Capacity Plan or through bilateral transactions with FRR Entities; or (g) any voluntary and arm’s 
length bilateral transaction (including but not limited to those reported pursuant to Tariff, 
Attachment DD, section 4.6), such as a power purchase agreement or other similar contract 
where the buyer is a Self-Supply Entity and the transaction is (1) a short term transaction (one-
year or less) or (2) a long-term transaction that is the result of a competitive process that was not 
fuel-specific and is not used for the purpose of supporting uneconomic construction, 
development, or operation of the subject Capacity Resource, provided however that if the Self-
Supply Entity is responsible for offering the Capacity Resource into an RPM Auction, the 
specified amount of installed capacity purchased by such Self-Supply Entity shall be considered 
to receive a State Subsidy in the same manner, under the same conditions, and to the same extent 
as any other Capacity Resource of a Self-Supply Entity.  For purposes of subsection (e) of this 
Page 13

PDF page 62

definition, a state default procurement auction that has been certified to be a result of a non-
discriminatory and competitive bidding process shall:
(i)
have no conditions based on the ownership (except supplier diversity 
requirements or limits), location (except to meet PJM deliverability 
requirements), affiliation, fuel type, technology, or emissions of any resources or 
supply (except state-mandated renewable portfolio standards for which Capacity 
Resources are separately subject to the minimum offer price rule or eligible for an 
exemption);
(ii)
result in contracts between an Entity Providing Supply Services to Default Retail 
Service Provider and the electric distribution company for a retail default 
generation supply product and none of those contracts require that the retail 
obligation be sourced from any specific Capacity Resource or resource type as set 
forth in subsection (i) above; and
(iii)
establish market-based compensation for a retail default generation supply 
product that retail customers can avoid paying for by obtaining supply from a 
competitive retail supplier of their choice.
State of Charge:
“State of Charge” shall mean the quantity of physical energy stored in an Energy Storage 
Resource Model Participant or in the storage component of a Hybrid Resource in proportion to 
its maximum State of Charge capability. State of Charge is quantified as defined in the PJM 
Manuals.
State of Charge Management:
“State of Charge Management” shall mean the control of State of Charge of an Energy Storage 
Resource Market Participant or Hybrid Resource using minimum and maximum discharge (and, 
as applicable, charge) limits, changes in operating mode (as applicable), discharging (and, as 
applicable, charging) offer curves, and self-scheduling of non-dispatchable sales (and, as 
applicable, purchases) of energy in the PJM markets.  State of Charge Management shall not 
interfere with the obligation of a Market Seller of an Energy Storage Resource Model Participant
or of a Hybrid Resource to follow PJM dispatch, consistent with all other resources.
Station Power:
“Station Power” shall mean energy used for operating the electric equipment on the site of a 
generation facility located in the PJM Region or for the heating, lighting, air-conditioning and 
office equipment needs of buildings on the site of such a generation facility that are used in the 
operation, maintenance, or repair of the facility.  Station Power does not include any energy (i) 
used to power synchronous condensers; (ii) used for pumping at a pumped storage facility; (iii) 
used in association with restoration or black start service; or (iv) that is Direct Charging Energy.
Sub-Annual Resource Constraint:
Page 14

PDF page 63

“Sub-Annual Resource Constraint” shall mean, for the 2017/2018 Delivery Year and for FRR 
Capacity Plans the 2017/2018 and 2018/2019 Delivery Years, for the PJM Region or for each 
LDA for which the Office of the Interconnection is required under Tariff, Attachment DD, 
section 5.10(a) to establish a separate VRR Curve for a Delivery Year, a limit on the total 
amount of Unforced Capacity that can be committed as Limited Demand Resources and 
Extended Summer Demand Resources for the 2017/2018 Delivery Year in the PJM Region or in 
such LDA, calculated as the Sub-Annual Resource Reliability Target for the PJM Region or for 
such LDA, respectively, minus the Short-Term Resource Procurement Target for the PJM 
Region or for such LDA, respectively. 
Sub-Annual Resource Price Decrement:
“Sub-Annual Resource Price Decrement” shall mean, for the 2017/2018 Delivery Year, a 
difference between the clearing price for Extended Summer Demand Resources and the clearing 
price for Annual Resources, representing the cost to procure additional Annual Resources out of 
merit order when the Sub-Annual Resource Constraint is binding. 
Sub-Annual Resource Reliability Target: 
“Sub-Annual Reliability Target” for the PJM Region or an LDA, shall mean the maximum 
amount of the combination of Extended Summer Demand Resources and Limited Demand 
Resources in Unforced Capacity determined by PJM to be consistent with the maintenance of 
reliability, stated in Unforced Capacity, that shall be used to calculate the Minimum Annual 
Resource Requirement for Delivery Years through May 31, 2017 and the Sub-Annual Resource 
Constraint for the 2017/2018 and 2018/2019 Delivery Years.  As more fully set forth in the PJM 
Manuals, PJM calculates the Sub-Annual Resource Reliability Target, by first determining a 
reference annual loss of load expectation (“LOLE”) assuming no Demand Resources.  The 
calculation for the unconstrained portion of the PJM Region uses a daily distribution of loads 
under a range of weather scenarios (based on the most recent load forecast and iteratively 
shifting the load distributions to result in the Installed Reserve Margin established for the 
Delivery Year in question) and a weekly capacity distribution (based on the cumulative capacity 
availability distributions developed for the Installed Reserve Margin study for the Delivery Year 
in question).  The calculation for each relevant LDA uses a daily distribution of loads under a 
range of weather scenarios (based on the most recent load forecast for the Delivery Year in 
question) and a weekly capacity distribution (based on the cumulative capacity availability 
distributions developed for the Capacity Emergency Transfer Objective study for the Delivery 
Year in question).  For the relevant LDA calculation, the weekly capacity distributions are 
adjusted to reflect the Capacity Emergency Transfer Limit for the Delivery Year in question.
For both the PJM Region and LDA analyses, PJM then models the commitment of varying 
amounts of DR (displacing otherwise committed generation) as interruptible from May 1 through 
October 31 and unavailable from November 1 through April 30 and calculates the LOLE at each 
DR level.  The Extended Summer DR Reliability Target is the DR amount, stated as a percentage 
of the unrestricted peak load, that produces no more than a ten percent increase in the LOLE, 
compared to the reference value.  The Sub-Annual Resource Reliability Target shall be 
expressed as a percentage of the forecasted peak load of the PJM Region or such LDA and is 
Page 15

PDF page 64

converted to Unforced Capacity by multiplying [the reliability target percentage] times [the 
Forecast Pool Requirement] times [the DR Factor] times [the forecasted peak load of the PJM 
Region or such LDA, reduced by the amount of load served under the FRR Alternative].
Sub-meter:
“Sub-meter” shall mean a metering point for electricity consumption that does not include all 
electricity consumption for the end-use customer as defined by the electric distribution company 
account number.  PJM shall only accept sub-meter load data from end-use customers for 
measurement and verification of Regulation service as set forth in the Economic Load Response 
rules and PJM Manuals.
Summer-Period Capacity Performance Resource:
“Summer-Period Capacity Performance Resource” shall have the same meaning specified in 
Tariff, Attachment DD, section 5.5A.
Surplus Interconnection Customer:
“Surplus Interconnection Customer” shall mean either an Interconnection Customer whose 
Generating Facility is already interconnected to the PJM Transmission System or one of its 
affiliates, or an unaffiliated entity that submits a Surplus Interconnection Request to utilize 
Surplus Interconnection Service within the Transmission System in the PJM Region.  A Surplus 
Interconnection Customer is not a New Service Customer.   
Surplus Interconnection Request:
“Surplus Interconnection Request” shall mean a request submitted by a Surplus Interconnection 
Customer, pursuant to Tariff, Attachment RR, to utilize Surplus Interconnection Service within 
the Transmission System in the PJM Region.  A Surplus Interconnection Request is not a New 
Service Request.
Surplus Interconnection Service:
“Surplus Interconnection Service” shall mean any unneeded portion of Interconnection Service 
established in an Interconnection Service Agreement, such that if Surplus Interconnection 
Service is utilized, the total amount of Interconnection Service at the Point of Interconnection 
would remain the same.
Switching and Tagging Rules:
“Switching and Tagging Rules” shall mean the switching and tagging procedures of 
Interconnected Transmission Owners and Interconnection Customer as they may be amended 
from time to time. 
Synchronized Reserve:
Page 16

PDF page 65

“Synchronized Reserve” shall mean the reserve capability of generation resources that can be 
converted fully into energy or Economic Load Response Participant resources whose demand 
can be reduced within ten minutes from the request of the Office of the Interconnection 
dispatcher, and is provided by equipment that is electrically synchronized to the Transmission 
System.
Synchronized Reserve Event:
“Synchronized Reserve Event” shall mean a request from the Office of the Interconnection to 
generation resources and/or Economic Load Response Participant resources able, assigned or 
self-scheduled to provide Synchronized Reserve in one or more specified Reserve Zones or 
Reserve Sub-zones, within ten minutes, to increase the energy output or reduce load by the 
amount of assigned or self-scheduled Synchronized Reserve capability.
Synchronized Reserve Requirement:
“Synchronized Reserve Requirement” shall mean the megawatts required to be maintained in a 
Reserve Zone or Reserve Sub-zone as Synchronized Reserve, absent any increase to account for 
additional reserves scheduled to address operational uncertainty.  The Synchronized Reserve 
Requirement is calculated in accordance with the PJM Manuals.  This requirement can only be 
satisfied by Synchronized Reserve resources.
System Condition:
“System Condition” shall mean a specified condition on the Transmission Provider’s system or 
on a neighboring system, such as a constrained transmission element or flowgate, that may 
trigger Curtailment of Long-Term Firm Point-to-Point Transmission Service using the 
curtailment priority pursuant to Tariff, Part II, section 13.6.  Such conditions must be identified 
in the Transmission Customer’s Service Agreement.
System Energy Price:
“System Energy Price” shall mean the energy component of the Locational Marginal Price, 
which is the price at which the Market Seller has offered to supply an additional increment of 
energy from a resource, calculated as specified in Operating Agreement, Schedule 1, section 2 
and the parallel provisions of Tariff, Attachment K-Appendix, section 2.
System Impact Study:
“System Impact Study” shall mean an assessment by the Transmission Provider of (i) the 
adequacy of the Transmission System to accommodate a Completed Application, an 
Interconnection Request or an Upgrade Request, (ii) whether any additional costs may be 
incurred in order to provide such transmission service or to accommodate an Interconnection 
Request, and (iii) with respect to an Interconnection Request, an estimated date that an 
Interconnection Customer’s Customer Facility can be interconnected with the Transmission 
Page 17

PDF page 66

System and an estimate of the Interconnection Customer’s cost responsibility for the 
interconnection; and (iv) with respect to an Upgrade Request, the estimated cost of the requested 
system upgrades or expansion, or of the cost of the system upgrades or expansion, necessary to 
provide the requested incremental rights.
System Protection Facilities:
“System Protection Facilities” shall refer to the equipment required to protect (i) the 
Transmission System, other delivery systems and/or other generating systems connected to the 
Transmission System from faults or other electrical disturbance occurring at or on the Customer 
Facility, and (ii) the Customer Facility from faults or other electrical system disturbance 
occurring on the Transmission System or on other delivery systems and/or other generating 
systems to which the Transmission System is directly or indirectly connected.  System Protection 
Facilities shall include such protective and regulating devices as are identified in the Applicable 
Technical Requirements and Standards or that are required by Applicable Laws and Regulations 
or other Applicable Standards, or as are otherwise necessary to protect personnel and equipment 
and to minimize deleterious effects to the Transmission System arising from the Customer 
Facility.
Page 18

PDF page 67

Tariff, Part VIII, Subpart A, section 400
Definitions F
Facilities Study:
“Facilities Study” shall be an engineering study conducted by the Transmission Provider (in 
coordination with the affected Transmission Owner(s)) to: (1) determine the required 
modifications to the Transmission Provider’s Transmission System necessary to implement the 
conclusions of the System Impact Studies; and (2) complete any additional studies or analyses 
documented in the System Impact Studies or required by PJM Manuals, and determine the 
required modifications to the Transmission Provider's Transmission System based on the 
conclusions of such additional studies.  
Federal Power Act:
“Federal Power Act” shall mean the Federal Power Act, as amended, 16 U.S.C. §§ 791a, et seq.
FERC or Commission:
“FERC” or “Commission” shall mean the Federal Energy Regulatory Commission or any 
successor federal agency, commission or department exercising jurisdiction over the Tariff, 
Operating Agreement and Reliability Assurance Agreement.
Final Agreement Negotiation Phase:
“Final Agreement Negotiation Phase” shall mean the phase set forth in Tariff, Part VIII, Subpart 
D, section 411 to tender, negotiate, and execute any service agreement in Tariff, Part IX. 
Firm Transmission Service:
“Firm Transmission Service” shall mean any or a combination of Network Integration 
Transmission Service, Firm Point-To-Point Transmission Service, or Firm Contract Demand 
Transmission Service taken by an Eligible Customer.
Page 19

PDF page 68

Tariff, Part VIII, Subpart N
COST RECOVERY PROTECTION AND AGREEMENT
Page 20

PDF page 69

Tariff, Part VIII, Subpart N, section 441
Cost Recovery Protection for Firm Transmission Service
(a) Cost Recovery Assurances: With respect to Eligible Customers that intend to request any 
form of Firm Transmission Service from Transmission Provider on behalf of an Eligible Load or 
Large Load, a Transmission Owner shall either:
(i)
Enter into a Cost Recovery Agreement in the form found in Tariff, Part IX, 
Subpart P with the applicable Eligible Customer and Eligible Load or Large Load.  The 
Transmission Owner counterparty shall be the Transmission Owner that owns the transmission 
facilities with which the Eligible Load or Large Load will interconnect.  In the case of an 
Eligible Load or Large Load that will not directly interconnect with a Transmission Owner, the 
Transmission Owner counterparty shall be the Transmission Owner to which the applicable 
Eligible Customer is connected and from whom the Eligible Customer intends to take Firm 
Transmission Service.  The purpose of the Cost Recovery Agreement is to ensure the Eligible 
Customer takes a minimum level of Firm Transmission Service on behalf of the Eligible Load or 
Large Load based on the committed load level and the applicable rate for the Firm Transmission 
Service, or, if not, the Eligible Load or Large Load shall be required to make a shortfall payment 
representing any difference between the committed minimum level of service and the actual 
level of service taken.
(ii)
Enter into, subject to FERC acceptance, a separate agreement between at least the 
Transmission Owner and an Eligible Load or Large Load to prevent cost shifting among 
transmission customers.  Such separate agreement will be determined to adequately prevent cost 
shifts if such agreement, in conjunction with relevant federal and state regulatory requirements, 
including applicable retail service tariffs, results in minimum Firm Transmission Service and 
credit standards, or other comparable protections.
An Eligible Customer and/or Eligible Load or Large Load will be required to enter into and 
execute a Cost Recovery Agreement or an agreement that meets the standards set forth in 
subsection (a)(ii) in order to proceed past the Soft Close Date associated with the applicable PJM 
Fast Energization Cycle, and obtain any form of Firm Transmission Service from the 
Transmission Provider.
(b) Preservation of Legacy Treatment: No Cost Recovery Agreement or separate agreement 
under subsection (a) above shall be required with respect to Eligible Load or Large Loads 
covered by existing agreements that meet the criteria set forth in subsection (a)(ii) that have 
already been filed and are pending acceptance, or that have been accepted by FERC.  Any 
agreement entered into prior to the effective date of this subsection not filed with FERC will not 
be required to be filed and accepted by FERC; provided, however, in any complaint filed 
pursuant to Section 206 of the Federal Power Act in which it is claimed that such agreement is 
not just and reasonable or is unduly discriminatory within the meaning of the Federal Power Act, 
such agreement shall not be determined to be unjust and unreasonable or unduly discriminatory 
if it meets the standard set forth in subsection (a)(ii).
(c) Tender and Negotiation of Cost Recovery Agreement:  As applicable, consistent with 
subsections (a) and (b) above, Transmission Owner shall tender a draft of the Cost Recovery 
Page 21

PDF page 70

Agreement to Eligible Customer and Eligible Load or Large Load within 30 days of the 
completion of the Transmission Owner’s retail load interconnection study.  
Upon receipt of the draft Cost Recovery Agreement, Eligible Customer, as well as the Eligible 
Load or Large Load, shall provide the Transmission Owner with any written comments on the 
draft Cost Recovery Agreement within seven (7) days. The parties will conduct further 
negotiations as required, with such negotiations to be completed within twenty-five (25) days of 
the Transmission Owner’s tender of the draft Cost Recovery Agreement.  
(d) Execution and Filing of Cost Recovery Agreement: Not later than ten (10) days after the 
end of the negotiation period set forth in subsection (c) above, Eligible Customer and the Eligible 
Load or Large Load shall (i) execute the Cost Recovery Agreement and return it to Transmission 
Owner; and (ii) provide the Credit Support specified in the Cost Recovery Agreement.
If the Eligible Load or Large Load fails to execute the Cost Recovery Agreement or provide the 
required Credit Support in the specified time period, Eligible Customer shall not be permitted to 
proceed through the applicable Fast Energization Cycle.  
The Transmission Owner shall file any executed Cost Recovery Agreement, if required, with 
FERC within twenty-one (21) days of the other parties executing the Cost Recovery Agreement.
(e) Crediting of Termination Amounts: If the effective date of an Early Termination or Partial 
Termination, as defined in a Cost Recovery Agreement, occurs prior to the first Service Date 
specified in such agreement, and the Eligible Load or Large Load that is a party to that 
agreement is required to make a termination payment, as applicable, such termination payment 
or other amounts received pursuant to such obligation, including any security drawn on by 
Transmission Owner, shall be divided amongst the pool of Transmission Owners constructing
facilities needed to provide the related transmission service, but which will no longer be 
constructed, including the Transmission Owner that is a party to the Cost Recovery Agreement, 
as follows:
(i)
Within thirty (30) days of such termination, the Transmission Owner that is party 
to the Cost Recovery Agreement (referred to herein as the “contracting Transmission Owner”) 
shall notify all other Transmission Owners that have been designated to construct and own 
Interconnection Reliability Reinforcements necessary to provide Firm Transmission Service to 
an Eligible Customer on behalf of the terminating Eligible Load or Large Load (referred to 
herein as the “third party Transmission Owners”) of such termination.  For purposes of this 
subsection, third party Transmission Owners shall include all Transmission Owners designated 
to construct and own Interconnection Reliability Reinforcements identified in the PJM Fast 
Energization Cycle in which the terminating Eligible Load or Large Load was studied, and for 
which the contracting Transmission Owner’s Zone received a cost responsibility share.
(ii)
Each third-party Transmission Owner shall, within thirty (30) days of the deadline 
for filings its FERC Form 1 that includes all Eligible Costs, provide an account of such Eligible 
Costs to the contracting Transmission Owner.  For purposes of this subsection “Eligible Costs” 
consist of all expenditures, costs, and cancellation fees incurred or due to commitments made by 
the third-party Transmission Owner to engineer, design, procure, construct, own, operate, 
Page 22

PDF page 71

maintain, and service the Interconnection Reliability Reinforcements needed to serve the Eligible 
Customer taking transmission service on behalf of the Eligible Load or Large Load, but which 
will no longer be constructed, which (a) are incurred through the end of the calendar year in 
which notice of termination was received from the contracting Transmission Owner, and (b) are 
included in amounts reported in the Transmission Owner’s FERC Form 1 covering that calendar 
year.  
Any failure by a third-party Transmission Owner to provide such information within the 
timeframe above shall bar said Transmission Owner from receiving a portion of amounts paid by 
Eligible Load or Large Load as set forth below.
(iii)
Within thirty (30) days of (a) receiving all Transmission Owner accountings in 
accordance with subsection (ii) above, and (b) receipt of termination amounts from the Eligible 
Load or Large Load that is party to the Cost Recovery Agreement,  the contracting Transmission 
Owner shall divide such termination amounts among itself and the pool of third-party 
Transmission Owners based on each Transmission Owner’s pro rata share of the total amount of 
applicable expenditures, costs and cancellation fees, and disburse such amounts to the third-party 
Transmission Owners accordingly.  
For purposes of determining these pro rata shares, the contracting Transmission Owner shall be 
permitted to include Eligible Costs associated not only with its applicable Interconnection 
Reliability Reinforcements but also any other transmission facilities, including Supplemental 
Projects and Direct Connection Facilities, that it was constructing in order to provide 
interconnection or transmission service to the Eligible Load or Large Load, or Eligible Customer 
taking transmission service on behalf of the Eligible Load or Large Load.
To the extent that additional termination funds are received or collected from the Eligible Load 
or Large Load after an initial distribution is made under this subsection, contracting 
Transmission Owner will make additional disbursements using the same methodology within 
fifteen (15) days of receipt of such amounts.
(iv)
Nothing in this subsection (e) is intended or shall be interpreted to prevent any 
Transmission Owner from seeking cost recovery through an abandoned plant recovery filing 
made with FERC or through any other proceeding, except insofar as the Transmission Owner has 
received amounts pursuant to the process set forth in this subsection (e), it shall be prohibited 
from requesting recovery of such amounts in any future proceeding.
(v)
To the extent a Transmission Owner elects to satisfy its obligation under 
subsection (a) above through a separate agreement as described in subsection (a)(ii), it shall 
include in such separate agreement reasonably comparable termination payment crediting 
provisions as set forth in this subsection (e), as determined by FERC.
(vi)
Any disputes under this subsection (e) shall be subject to the dispute resolution 
procedure set forth in Schedule 5 of the Operating Agreement.
Page 23

PDF page 72

Tariff, Part IX, Subpart P
FORM OF
COST RECOVERY AGREEMENT
Page 24

PDF page 73

Service Agreement No. [____]
COST RECOVERY AGREEMENT
Between
[TRANSMISSION OWNER] 
Transmission Owner
and
[LARGE LOAD CUSTOMER]
Large Load Customer
and 
[ELIGIBLE CUSTOMER]
Eligible Customer
Page 25

PDF page 74

Service Agreement No. [____]
COST RECOVERY AGREEMENT
This Cost Recovery Agreement (“Agreement” or “CRA”) is made and entered into as of 
[Insert Date] by and among [Transmission Owner], a [State and Entity Type] (“Transmission 
Owner”) and [Large Load Customer], a [State and Entity Type] (“Large Load Customer”), and
[Eligible Customer], a [State and Entity Type] (“Eligible Customer”). Transmission Owner, 
Eligible Customer, and Large Load Customer are referred to individually as a “Party” and 
collectively as the “Parties.” 
Large Load Customer will be responsible for all payment and Credit Support obligations 
assigned to Large Load Customer under this CRA. Eligible Customer will remain responsible for 
the transmission-service, information-sharing, and administrative obligations expressly assigned 
to Eligible Customer under this CRA.
RECITALS
WHEREAS, Large Load Customer intends to construct, maintain, and operate new or 
modified facilities located at or near [Facility Address] that will constitute a Large Load (the 
“Large Load Facilities”), with an anticipated initial service date of [Date] (the “Commercial 
Operation Date”);
WHEREAS, Large Load Customer has completed retail interconnection studies 
conducted by Transmission Owner and/or one or more of its affiliates;
WHEREAS,
following completion of the applicable Transmission Owner’s 
interconnection study process, the Parties are entering into this CRA based on the Initial Load 
Commitment, proposed load ramp, and anticipated Service Dates identified in Exhibit A;
WHEREAS, Eligible Customer intends to request Network Integration Transmission 
Service (“NITS”), Firm Point-to-Point Transmission Service, or Firm Contract Demand 
Transmission Service (“FCDS”) under the PJM Open Access Transmission Tariff (“PJM Tariff”) 
on behalf of the Large Load Customer to serve the Large Load Facilities , each of which 
constitutes “Firm Transmission Service” under this CRA;
WHEREAS, Exhibit A identifies the initial amount and type of Firm Transmission 
Service to be requested by Eligible Customer on behalf of Large Load Customer, together with 
the load ramp and anticipated Service Dates;
WHEREAS, following completion of the applicable application and study process to 
obtain the Firm Transmission Service, Exhibit A and the related calculations under this CRA will 
be updated to reflect the type, amount, and timing of Firm Transmission Service established in 
the Final PJM Agreement;
WHEREAS, in reliance on the Firm Load Commitment and in accordance with the PJM 
Tariff and other applicable agreements, the Transmission Owner intends to construct, own, 
Page 26

PDF page 75

operate, maintain, service, and recover the costs associated with transmission facilities necessary 
to serve the Large Load Facilities;
WHEREAS, this CRA establishes the payment and Credit Support obligations described 
herein and allocates the financial risk arising if Firm Transmission Service-related revenues 
attributable to service actually taken for the Large Load Facilities are less than the Committed 
Revenue Contribution.
NOW, THEREFORE, in consideration of the premises and the mutual covenants and 
undertakings set forth herein, the receipt and sufficiency of which are acknowledged, the Parties, 
intending to be legally bound, agree as follows:
ARTICLE 1
DEFINITIONS
1.0
Defined Terms 
Capitalized terms used in this CRA have the meanings set forth below. Capitalized terms used 
but not defined in this CRA have the meanings set forth in the PJM Tariff.
(a)
“Actual Revenue Contribution” means, for each Measurement Period, the Firm 
Transmission Service-related revenues attributable to Firm Transmission Service actually 
taken by 
Eligible Customer to serve the Large Load Facilities, as calculated in 
accordance with Section 5.2 and Exhibit B.
(b) 
“Agreement” or “CRA” means this Cost Recovery Agreement, including its Exhibits and 
any amendments that become effective in accordance with this CRA and applicable law.
(c)
“Applicable Credits” means the amounts identified in Article 9 and Exhibit D, Section 4, 
that are deducted in calculating the Early Termination Amount or Partial Termination 
Amount, without duplication.
(d)
“Applicable Firm Transmission Service Rate” means, for each Measurement Period, the 
Transmission Owner’s rate or rates then in effect under the PJM Tariff for the applicable 
Firm Transmission Service in the applicable Transmission Zone, as used to calculate the 
charges corresponding to the Firm Load Commitment.
(e)
“Applicable Termination Percentage” means the percentage set forth in Exhibit D for the 
period in which the termination or Partial Termination becomes effective.
(f)
“Business Day” means any day other than a Saturday, Sunday, or holiday recognized by 
the North American Electric Reliability Corporation.
(g)
“Commercial Operation Date” means the anticipated initial service date for the Large 
Load Facilities identified in Exhibit A.
(h)
“Committed Revenue Contribution”
means, for each Measurement Period, the 
contractually required portion of the Full Firm Transmission Service Benchmark, 
calculated by applying the Minimum Commitment Percentage in accordance with Section 
5.1 and Exhibit B.
(i)
“Credit Support” means the financial security that Large Load Customer is required to 
provide and maintain under Section 6.1 to secure Large Load Customer’s payment and 
other financial obligations under this CRA.
Page 27

PDF page 76

(j)
“Credit Support Requirement” means the amount of Credit Support that Large Load 
Customer is required to cause to be provided and maintained, as calculated in accordance 
with Section 6.5 and Exhibit C based on the aggregate Projected Full Firm Transmission 
Service Benchmarks for all Measurement Periods remaining in the Term, including any 
portion of the applicable Measurement Period that remains incomplete. Before the 
recalculation required under Section 3.2, the Credit Support Requirement shall be the 
Initial Credit Support Requirement.
(k)
“Effective Date” means the date on which this CRA becomes effective as set forth in 
Section 4.1.
(l)
“Early Termination Amount” means the amount payable by Large Load Customer upon 
a termination of this CRA for which an Early Termination Amount is required under 
Article 9, as calculated in accordance with Exhibit D.
(m)
“Early Termination Offset Amount” means the Firm Transmission Service-related 
revenues received by Transmission Owner during the period corresponding to the 
remaining fixed period from incremental replacement load served at the same Point of 
Delivery, to the extent those revenues correspond to the revenue exposure included in the 
Early Termination Amount or Partial Termination Amount, as determined in accordance 
with Section 9.9.
(n)
“Eligible Customer” means the Person identified as  Eligible Customer in the preamble to 
this CRA, which is an Eligible Customer under the PJM Tariff and the entity responsible 
for taking Firm Transmission Service on behalf of Large Load Customer to serve the 
Large Load Facilities. Eligible Customer is responsible only for the obligations expressly 
assigned to Eligible Customer under this CRA and is not responsible for Large Load 
Customer’s payment or Credit Support obligations.
(o)
“FERC” means the Federal Energy Regulatory Commission or any successor agency.
(p)
“Final PJM Agreement” means the final Transmission Service Agreement or other 
agreement executed under the PJM Tariff that identifies the Firm Transmission Service to 
be taken by Eligible Customer on behalf of Large Load Customer.
(q)
“Firm Load Commitment” means the amount of firm load identified in Exhibit A, 
together with the corresponding level of Firm Transmission Service that Eligible 
Customer has committed to take on behalf of  Large Load Customer and any associated 
load-ramp milestones and Service Dates.
(r)
“Firm Transmission Service” means NITS, Firm Point-to-Point Transmission Service, or 
FCDS, as applicable, requested or taken by Eligible Customer under the PJM Tariff on 
behalf of Large Load Customer to serve the Large Load Facilities. 
(s)
“Full Firm Transmission Service Benchmark” means, for each Measurement Period, the 
charges that would apply under the Applicable Firm Transmission Service Rate and 
applicable billing determinants if Eligible Customer took Firm Transmission Service 
corresponding to the Firm Load Commitment scheduled to apply during that 
Measurement Period, as calculated in accordance with Section 5.1 and Exhibit B.
(t)
“Force Majeure” has the meaning set forth in Article 12.
(u)
“FCDS” means Firm Contract Demand Transmission Service under the PJM Tariff.
(v)
“Initial Load Commitment” means the initial amount of Firm Transmission Service to be 
requested by Eligible Customer on behalf of Large Load Customer, together with the 
proposed load ramp and anticipated Service Dates identified in Exhibit A at execution of 
this CRA.
Page 28

PDF page 77

(w)
“Initial Credit Support Requirement” means the amount of Credit Support identified in 
Exhibit C at execution by the Parties of this CRA based on the Initial Load Commitment, 
anticipated Service Dates, and aggregate Projected Full Firm Transmission Service 
Benchmarks for the Term, calculated in accordance with  the methodology specified in 
Exhibit C.
(x)
“Large Load” shall mean end-use customer(s) load that has a cumulative peak load of 50 
megawatts or greater at a single electrical site behind one or more points of 
interconnection, where for configurations involving multiple affiliated load facilities or 
multiple points of interconnection with affiliated load facilities behind them, all affiliated 
load facilities within a one-mile radius will be considered a single electrical site as further 
described in the PJM Manuals.
(y)
“Large Load Customer” means the Person identified in Exhibit A that owns, operates, 
leases, or otherwise controls the Large Load Facilities and on whose behalf Eligible 
Customer takes Firm Transmission Service to serve the Large Load Facilities. Large 
Load Customer is a Party to this CRA and is directly responsible for the payment and 
Credit Support obligations assigned to Large Load Customer under this CRA.
(z)
“Large Load Facilities” means the new or modified facilities identified in Exhibit A that 
constitute the Large Load.
(aa)
“Measurement Period”  means each period, not to exceed one year, corresponding to 
Transmission Owner’s applicable formula rate cycle, or portion thereof, beginning on the 
first Service Date and continuing through the end of the Term, as specified in Exhibit A.
(bb)
“Minimum Commitment Percentage” means the percentage specified in Exhibit A that is 
applied to the Full Firm Transmission Service Benchmark to calculate the Committed 
Revenue Contribution, which percentage shall be no less than 80% and no greater than 
100%, per the schedule set forth in Exhibit A below.
(cc)
“MW” means megawatts.
(dd)
“NITS” means Network Integration Transmission Service provided pursuant to the PJM 
Tariff, Part III.
(ee)
“Partial Termination Amount” means the amount payable by Large Load Customer upon 
a permanent reduction of a specified portion of the Firm Load Commitment under 
Section 9.2, as calculated in accordance with Section 9.8 and Exhibit D.
(ff)
“Person” means an individual, corporation, limited liability company, partnership, 
association, trust, governmental authority, or other legal entity.
(gg)
“PJM” means PJM Interconnection, L.L.C. or its successor.
(hh)
“PJM Tariff” means the PJM Open Access Transmission Tariff, as accepted by FERC 
and effective from time to time.
(ii)
“Projected Committed Revenue Contributions” means the aggregate amounts projected to 
constitute Committed Revenue Contributions during the applicable period, calculated by 
applying the Minimum Commitment Percentage to the Projected Full Firm Transmission 
Service Benchmark for each applicable Measurement Period. 
(jj)
“Project Development Costs” means all expenditures, costs, and cancellation fees 
incurred, or due to commitments made by the Transmission Owner or other transmission 
owners to engineer, design, procure, construct, own, operate, maintain, and service the 
necessary transmission facilities needed to serve the Large Load Customer that are 
intended to be placed into transmission rate base and recovered through transmission 
rates.  
Page 29

PDF page 78

(kk)
“Projected Full Firm Transmission Service Benchmark” means, for each applicable 
Measurement Period, 100% of the Firm Transmission Service-related charges projected 
to apply if Eligible Customer takes Firm Transmission Service corresponding to the 
Initial Load Commitment or Firm Load Commitment, as applicable, calculated in 
accordance with Exhibit C.
(ll)
“Service Date” means (i) before execution of the Final PJM Agreement, each anticipated 
date identified in Exhibit A on which the Initial Load Commitment, or a portion thereof, 
is expected to become effective; and (ii) after execution of the Final PJM Agreement, 
each date identified in Exhibit A as updated pursuant to Section 3.2 on which the Firm 
Load Commitment, or a specified portion thereof under an applicable load ramp, is 
scheduled to become effective..
(mm) “Shortfall Amount” means, for each Measurement Period, the amount, if any, by which 
the Committed Revenue Contribution exceeds the Actual Revenue Contribution, as 
calculated in accordance with Section 5.3 and Exhibit B.
(nn)
“Term” has the meaning set forth in Section 4.2.
(oo)
“Transmission Owner” means the PJM Transmission Owner identified in the preamble to 
this CRA.
(pp)
“Transmission System” shall mean the facilities controlled or operated by PJM that are 
used to provide transmission service under Part II and Part III of the PJM Tariff. 
(qq)
“Transmission Zone” means the transmission zone identified in Exhibit A in which the 
Large Load Facilities are located.
ARTICLE 2
RECITALS
2.1
Recitals
The statements set forth in the recitals above are hereby incorporated herein into the terms and 
conditions of this CRA as if fully set forth herein.
ARTICLE 3
FIRM LOAD COMMITMENT
3.1
Initial Load Commitment and Firm Load Commitment
At execution of this CRA, the Initial Load Commitment shall be established using the amount 
and type of Firm Transmission Service that Eligible Customer intends to request from PJM on 
behalf of Large Load Customer through the applicable application and study process, together 
with the proposed load ramp and anticipated Service Dates identified in Exhibit A.
Following execution of the Final PJM Agreement, the Firm Load Commitment applicable during 
each Measurement Period shall be the amount and type of Firm Transmission Service that the 
Eligible Customer takes on behalf of the Large Load during each Measurement Period, as set 
forth in Exhibit A.  This amount shall be based on the amount of load for the Large Load 
scheduled to be in service during each Measurement Period, or the amount of Firm Transmission 
Service that the Eligible Customer has contracted for on behalf of the Large Load.
Page 30

PDF page 79

If Exhibit A establishes a load ramp, consistent with the amount of Firm Transmission Service 
that the Eligible Customer has contracted for on behalf of the Large Load, each scheduled load 
level becomes part of the Firm Load Commitment on the applicable Service Date.
Except as expressly provided in this CRA, Eligible Customer’s failure to begin taking Firm 
Transmission Service to serve the Large Load Facilities, take Firm Transmission Service
corresponding to a scheduled load level, or maintain that level of Firm Transmission Service
does not reduce or defer the Firm Load Commitment or the Committed Revenue Contribution, or 
excuse Large Load Customer from any payment or Credit Support obligation under this CRA.
3.2
Post-Final PJM Agreement Update and Subsequent Modification
Within thirty (30) days after execution of the Final PJM Agreement, Transmission Owner shall 
update Exhibit A to reflect the Firm Transmission Service, load ramp, and Service Dates 
established through or consistent with the Final PJM Agreement. Transmission Owner shall also 
update the Applicable Firm Transmission Service Rate, Projected Committed Revenue 
Contributions, Projected Full Firm Transmission Service Benchmarks, Credit Support 
Requirement, the applicable schedules in Exhibits A and C, and the calculations under Exhibit B 
using the information then available.
The information reflected in the Final PJM Agreement shall control over the corresponding 
preliminary information included in Exhibit A at execution. If the Final PJM Agreement 
establishes less Firm Transmission Service than the Initial Load Commitment, the Firm Load 
Commitment shall be reduced accordingly. A reduction required by this paragraph shall not 
constitute a Partial Termination and shall not result in a Partial Termination Amount.
An update required by this Section shall become effective without further agreement of the 
Parties and shall not constitute an amendment to this CRA. Transmission Owner shall provide 
the updated Exhibits and reasonable supporting calculations to Eligible Customer and Large 
Load Customer.
After the update required by this Section, a further modification to the Firm Load Commitment 
or a Service Date shall become effective only if the Parties execute any amendment required 
under this CRA and the amendment receives any required PJM or FERC acceptance or approval. 
A customer-requested reduction remains subject to Article 9.
3.3
No Transmission Owner Obligation
Except as otherwise explicitly provided herein, nothing in this Agreement shall constitute an 
obligation on the part of Transmission Owner to provide any service to any Party or place into 
service any transmission facilities by any specific date or dates. 
ARTICLE 4
EFFECTIVE DATE AND TERM
4.1
Effective Date
Page 31

PDF page 80

This CRA will become effective on the later of : (1) the date  executed by all Parties, or (2) the 
date accepted or approved by FERC, if such acceptance or  approval is required, or (3) on such 
other date as FERC may establish in an order accepting or approving the CRA (the “Effective 
Date”).
4.2
Term
Unless terminated earlier in accordance with this CRA, the term of this CRA (the “Term”) shall
commence on the Effective Date and continue until the later of:  (i) the date that is at least ten 
(10) years after the first Service Date as specified in Exhibit A; and (ii) the date on which all 
outstanding obligations under this CRA have been satisfied. 
ARTICLE 5
REVENUE CONTRIBUTIONS AND SHORTFALL AMOUNT
5.1
Committed Revenue Contribution
For each Measurement Period during the Term, Transmission Owner  shall calculate the 
Committed Revenue Contribution in accordance with this Section and Exhibit B, using the 
applicable rates, billing determinants, and other information available in accordance with the 
PJM Tariff.  The Committed Revenue Contribution shall equal the Minimum Commitment 
Percentage multiplied by the Firm Transmission Service-related charges that would apply if 
Eligible Customer took Firm Transmission Service corresponding to the Firm Load Commitment 
applicable during the Measurement Period.
The calculation shall use:
(a) the Firm Load Commitment that applies during each Measurement Period;
(b) the Applicable Firm Transmission Service Rate and the generally applicable billing 
determinants under the PJM Tariff; and
(c) the portion of the Measurement Period during which each scheduled Firm Load 
Commitment amount and Applicable Firm Transmission Service Rate applies.
If more than one Firm Load Commitment amount or Applicable Firm Transmission Service Rate 
applies during a Measurement Period, Transmission Owner 
shall calculate separately the 
amount applicable to each portion of the Measurement Period and aggregate those amounts to 
determine the Committed Revenue Contribution for the applicable Measurement Period.
Eligible Customer shall be responsible for timely payment of charges for Firm Transmission 
Service in a given calendar year on a monthly basis in accordance with the PJM Tariff.
5.2
Actual Revenue Contribution
For each Measurement Period during the Term, Transmission Owner shall calculate the Actual 
Revenue Contribution attributable to Firm Transmission Service actually taken to serve the 
Large Load Facilities in accordance with Exhibit B.  To the extent that the Large Load Customer 
has made separate payments through a retail tariff or other retail mechanism that reflect the 
assignment of Firm Transmission Service or related costs to the Large Load Customer, such 
Page 32

PDF page 81

payments shall be taken into account in determining its Actual Revenue Contribution, insofar as 
doing so does not result in costs being shifted to other Eligible Customers taking service in the 
Transmission Owner’s Zone. To the extent that the applicable Firm Transmission Service 
methodology calculates charges using an assigned Network Service Peak Load contribution or 
another allocated billing determinant, the Actual Revenue Contribution shall be calculated using 
the billing determinant assigned to the Large Load Facilities for the applicable Measurement 
Period and the same categories of rates used to calculate the Committed Revenue Contribution.
5.3
Shortfall Amount
For each Measurement Period, the Shortfall Amount shall equal the amount, if any, by which the 
Committed Revenue Contribution exceeds the Actual Revenue Contribution in accordance with 
Exhibit B.
Large Load Customer shall pay each Shortfall Amount in accordance with Article 7.
5.4
Separate Measurement Periods
Each Measurement Period shall be calculated independently.
5.5
Commencement of Committed Revenue Contribution
The determination of the Committed Revenue Contribution and any corresponding Shortfall 
Amounts shall begin on the corresponding Service Date, as set forth in Exhibit A, regardless of 
whether: (i) Eligible Customer has begun taking the corresponding level of Firm Transmission 
Service; (ii) the amount of Firm Transmission Service taken by Eligible Customer corresponds to 
the load level scheduled to apply on that Service Date; or (iii) the Large Load Facilities are 
operating at a lower load level than the one scheduled to apply on that Service Date.
Notwithstanding the foregoing, if Eligible Customer cannot begin taking the applicable Firm 
Transmission Service on a Service Date solely because the necessary transmission facilities have 
not been  completed, and such delay was not  caused in whole or in part by Large Load 
Customer’s or Eligible Customer’s failure or lack of reasonable diligence in satisfying  its 
obligations under this CRA or under any other binding agreement, tariff, regulatory order, or 
other legal requirement, the Service Date and commencement of the corresponding Committed 
Revenue Contribution shall be extended on a day-for-day basis until the Firm Transmission 
Service becomes available.  Large Load Customer’s obligations include, without limitation (a) 
construction, testing, commissioning and readiness of any facilities being constructed by Large 
Load Customer, and (b) prompt and reasonable responses to Transmission Owner’s or 
Transmission Owners’ affiliate(s)’ requests for information, approvals, or other communications 
necessary for Transmission Owner’s or Transmission Owners’ affiliate(s)’ work.
5.6  
Access to Information
Eligible Customer shall provide, or authorize access to, the service, billing, settlement, and 
allocation information from PJM or any other entity reasonably necessary for Transmission 
Owner to calculate the Actual Revenue Contribution, Shortfall Amount, or any other calculation 
Page 33

PDF page 82

required under this Agreement.
ARTICLE 6
CREDIT SUPPORT
6.1
Obligation to Post and Maintain Credit Support
In accordance with Tariff, Part VIII, Subpart N, section 441(d), Large Load Customer shall, at its 
own expense, cause Credit Support equal to the Initial Credit Support Requirement identified in 
Exhibit C to be provided in favor of Transmission Owner not later than ten (10) days after the 
end of the negotiation period specified in Tariff, Part VIII, Subpart N, section 441(c).
If Large Load Customer fails to provide the required Credit Support within that period, the 
consequences specified in Tariff, Part VIII, Subpart N, section 441(d) shall apply.
Within five (5) Business Days after receipt of the post-PJM recalculation required under Section 
3.2, Large Load Customer shall cause the Credit Support to be increased, reduced, amended, or 
replaced as necessary to equal the recalculated Credit Support Requirement.
The Credit Support shall secure Large Load Customer’s payment and other financial obligations 
under this CRA and shall at all times equal or exceed the Credit Support Requirement set forth in 
Exhibit C, subject to any reduction or treatment of prior draws expressly provided in this CRA.
The Credit Support Requirement shall be based on 100% of the Projected Full Firm 
Transmission Service Benchmarks for the applicable remaining Measurement Periods and shall 
not be reduced by the Minimum Commitment Percentage.
Large Load Customer shall cause the Credit Support to be maintained throughout the Term and 
thereafter until:
(a) all Shortfall Amounts and other amounts due under this CRA have been paid;
(b) the final reconciliation required under this CRA has been completed; and
(c) Transmission Owner has no remaining right to draw on the Credit Support under this 
CRA.
6.2 
Form of Credit Support 
Credit Support shall be a Letter of Credit in the form specified in Exhibit C and related 
attachments to Exhibit C.  
6.3
Replacement of Credit Support
Large Load Customer shall cause compliant replacement Credit Support to be provided within
five (5) Business Days after notice from Transmission Owner if:  (i) the issuer ceases to satisfy 
the requirements of Exhibit C; (ii) the Credit Support ceases to satisfy this Article 6; (iii) the 
Credit Support will expire or terminate before Large Load Customer’s obligation to maintain 
Credit Support ends; or (iv) the issuer gives notice of nonrenewal.
Page 34

PDF page 83

Replacement Credit Support provided under this Section shall be in an amount equal to the then-
applicable Credit Support Requirement, as  determined under Section 6.5 and Exhibit C as of the 
replacement date to reflect any completed Measurement Period that has been excluded from the 
Credit Support Requirement in accordance with Section 6.5, less the amount of any cash security 
then held by Transmission Owner and legally available to secure the same obligations.
6.4
Preservation Draw
If Large Load Customer fails to cause timely replacement Credit Support to be provided under 
Section 6.3, Transmission Owner may draw the lesser of: (i) the full amount then available under 
the existing Credit Support; and (ii) the then-applicable Credit Support Requirement, less any 
cash security then held by Transmission Owner and legally available to secure the same 
obligations. Transmission Owner may hold the proceeds as cash security for Large Load 
Customer’s obligations under this CRA.
A preservation draw does not constitute payment of an obligation unless and until Transmission 
Owner applies the proceeds to an amount due under this CRA.
Transmission Owner shall release cash security held under this Section after Large Load 
Customer causes compliant replacement Credit Support to be provided, except to the extent the 
cash has been applied to an amount due.
6.5
Adjustment of Credit Support Requirement
The Credit Support Requirement for each applicable period shall be calculated in accordance 
with Exhibit C.
Transmission Owner shall also recalculate the Credit Support Requirement following the update 
required under Section 3.2. That recalculation shall replace the Initial Credit Support 
Requirement and shall reflect the Firm Load Commitment, Service Dates, Applicable Firm 
Transmission Service Rate, Projected Full Firm Transmission Service Benchmarks, and other 
information established following the Final PJM Agreement.
Transmission Owner shall recalculate the Credit Support Requirement after completion of each 
Measurement Period and upon any other recalculation event specified in Exhibit C. The 
recalculated Credit Support Requirement shall equal the aggregate Projected Full Firm 
Transmission Service Benchmarks for the Measurement Periods remaining in the Term, 
including any incomplete portion of the applicable Measurement Period. A completed 
Measurement Period shall be excluded from the Credit Support Requirement only after: (i) the 
Committed Revenue Contribution, Actual Revenue Contribution, and any resulting Shortfall 
Amount for that Measurement Period have been finally calculated; and (ii) Large Load Customer 
has paid all amounts due for that Measurement Period.
If the Credit Support Requirement increases, Large Load Customer shall cause the Credit 
Support to be increased to the recalculated Credit Support Requirement within five (5) Business 
Days after receipt of the calculation.
Page 35

PDF page 84

If the Credit Support Requirement decreases, Transmission Owner shall authorize a 
corresponding reduction within five (5) Business Days of a request by the financial institution 
issuing the Credit Support for such authorization, provided that no payment default or other 
Event of Default exists and the remaining Credit Support, together with any cash security held by 
Transmission Owner, will equal or exceed the adjusted Credit Support Requirement.
Actual Revenue Contributions for a completed Measurement Period shall be used to determine 
the Shortfall Amount for that completed Measurement Period but shall not reduce the Projected 
Full Firm Transmission Service Benchmarks used to calculate the Credit Support Requirement 
for future Measurement Periods.
6.6
Draws for Unpaid Amounts
Except for a preservation draw under Section 6.4, Transmission Owner may draw on Credit 
Support only after:  (i) Transmission Owner has issued an invoice identifying an amount due 
under this CRA and the basis for that amount; and  (ii) Large Load Customer has failed to pay 
the invoiced amount within the payment period specified in Article 7.
A draw shall not exceed the amount due and unpaid.
Transmission Owner shall apply the proceeds of a draw to the unpaid amount for which the draw 
was made. Proceeds applied to a Shortfall Amount shall be credited in accordance with Section 
7.6, and proceeds applied to an Early Termination Amount or Partial Termination Amount shall 
be applied and credited in accordance with Section 9.12.  Large Load Customer’s payment 
default shall be cured to the extent Transmission Owner receives and applies proceeds sufficient 
to satisfy the unpaid amount.
6.7
Replenishment
Following a draw applied to satisfy an unpaid amount,  Large Load Customer shall cause the 
Credit Support to be restored to the applicable Credit Support Requirement within five (5) 
Business Days after notice from Transmission Owner.
6.8
Release of Credit Support
Transmission Owner shall release the remaining Credit Support within ninety (90) days after the 
latest of:  (i) expiration or termination of the Term; (ii) completion of all calculations, invoices, 
and reconciliations required under this CRA; (iii) payment of all undisputed amounts determined 
to be due under this CRA; or (iv) resolution of any pending dispute that could result in an 
additional amount payable by Large Load Customer .
Transmission Owner shall provide release or cancellation documentation relating to Credit 
Support to Large Load Customer, with a copy to Eligible Customer.
ARTICLE 7
Page 36

PDF page 85

INVOICING AND PAYMENT
7.1
Determination and Invoice
After the end of each Measurement Period, Transmission Owner shall calculate the Committed 
Revenue Contribution, Actual Revenue Contribution, and resulting Shortfall Amount in 
accordance with Article 5 and Exhibit B.
If a Shortfall Amount exists, Transmission Owner shall inform the other Parties and issue an 
invoice to Large Load Customer for the Shortfall Amount within sixty (60)  days after the end of 
the applicable Measurement Period.  Transmission Owner shall provide Eligible Customer with a 
copy of the invoice.
7.2
Payment
Large Load Customer shall timely pay all amounts invoiced and due under this CRA by no later 
than thirty (30) days after the date of receipt of the applicable invoice.  Any payment made after 
thirty (30) days, including any draw made by a Transmission Owner pursuant to Sections 6.6 and 
7.3 below shall include interest at the FERC rate set forth in 18 CFR Section 35.19.
7.3
Draw on Credit Support
If Large Load Customer fails to timely pay an invoiced amount, Transmission Owner may draw 
on the Credit Support for the unpaid amount in accordance with Section 6.6.
7.4
Review of Supporting Documentation
Upon Large Load Customer’s timely request, Transmission Owner and  if applicable, Eligible 
Customer, shall provide documentation reasonably necessary to enable Large Load Customer to
verify the accuracy of an invoice, subject to applicable confidentiality requirements.  For 
purposes of this section, a request shall be considered timely if made no more than five (5) 
Business Days after the date of receipt of the applicable invoice.  
Eligible Customer shall provide or authorize access to any service, billing, settlement, or 
allocation information reasonably necessary to support that review.
A request under this section shall not act to defer or extend the date on which payment is due 
under Section 7.2.
7.5
Disputed Amounts
Large Load Customer shall timely pay each invoiced amount notwithstanding any dispute, and 
Transmission Owner’s right to draw on Credit Support shall not be suspended by the dispute. If 
the final resolution determines that Large Load Customer paid, or Transmission Owner drew, 
more than the amount properly due, Transmission Owner shall promptly return the excess 
amount.  Any dispute must be made by no later than the date payment is due and conform to the 
Page 37

PDF page 86

requirements set forth in Section 15.1 below.
7.6
Crediting of Shortfall Amounts
All Shortfall Amounts collected by Transmission Owner shall be credited against the 
Transmission Revenue Requirement of the Transmission Owner for the Transmission  Zone in 
which the Eligible Customer is taking Firm Transmission Service.  Transmission Owner shall 
account for and credit all amounts received under this CRA in accordance with this Section 7.6, 
Section 9.12, as applicable, the PJM Tariff, and its applicable FERC-jurisdictional rate.  
Transmission Owner’s calculation, collection, accounting, and crediting of Shortfall Amounts 
shall be reflected in, and remain subject to review under, Transmission Owner’s applicable 
FERC-jurisdictional formula rate and related protocols.
ARTICLE 8
DEFAULT AND REMEDIES
8.1
Events of Default
Each of the following constitutes an “Event of Default” by the applicable Party:
(a) failure by Large Load Customer to cause the initial Credit Support to be timely 
provided in the amount and form required under this CRA;
(b) failure by Large Load Customer to cause to be timely provided replacement or 
additional Credit Support required under Article 6;
(c) failure by Large Load Customer to cause Credit Support to be replenished when 
required under Section 6.7;
(d) a material misrepresentation by a Party concerning the Firm Load Commitment, 
Actual Revenue Contribution, Credit Support, or another material matter under this CRA;
(e) assignment or attempted assignment of this CRA by a Party in violation of Article 10;
(f) repudiation of this CRA by a Party; 
(g) failure by Eligible Customer to take any PJM Tariff action expressly required of 
Eligible Customer under this CRA or a default by Eligible Customer under any PJM 
agreement relating to the provision of Firm Transmission Service; or
(h) failure by Eligible Customer or Large Load Customer to take an action expressly 
required under this CRA to request, pursue, or complete the applicable PJM process; or
(i) a default by Large Load Customer under any agreement with Transmission Owner or 
its Affiliates relating to the Large Load Facilities, including any failure to comply with 
any retail service tariffs, retail agreements, or other retail obligations that would prevent 
the Large Load Customer from meeting its obligations under this CRA;
(j) the bankruptcy or insolvency of Large Load Customer; or
(k) any other material breach by a Party  that remains uncured after the applicable period 
provided in Section 8.2.
8.2
Notice and Cure
Except as otherwise expressly provided in this CRA, Transmission Owner shall provide the 
Defaulting Party with written notice of an Event of Default describing the default in reasonable 
detail.
Page 38

PDF page 87

The Defaulting Party  shall have: (i) five (5) Business Days after receipt of notice to cure a 
Credit Support default; and (ii) fifteen  (15) days after receipt of notice to cure any other curable 
Event of Default.
8.3
Remedies
Following an Event of Default that has not been timely cured, the non-Defaulting Party or Parties  
may, in their sole discretion:
(a) if Transmission Owner is a non-Defaulting Party, draw on Credit Support in 
accordance with this CRA;
(b) recover any amount due and unpaid under this CRA;
(c) require specific performance of Large Load Customer’s obligation to cause Credit 
Support to be provided or maintained;
(d) exercise any right or remedy available under the PJM Tariff to the extent applicable to 
that Party;
(e) terminate this CRA only as expressly permitted under Article 9; and
(f) exercise any other right or remedy available under applicable law.
Transmission Owner shall credit all payments and Credit Support proceeds against the obligation 
for which they were received and shall not obtain duplicative recovery of the same amount.
8.4
Effect of Credit Support Draw
Receipt and application of Credit Support proceeds sufficient to satisfy an unpaid amount shall 
cure the applicable payment default to the extent of the proceeds received and applied.
ARTICLE 9
EARLY AND PARTIAL TERMINATION
9.1
Termination or Reduction by Large Load Customer; Withdrawal from PJM 
Process
Before execution of the Final PJM Agreement, Eligible Customer’s withdrawal or abandonment 
of the request for Firm Transmission Service from the applicable PJM process on behalf of Large 
Load Customer, or refusal to execute the Final PJM Agreement shall constitute an early 
termination of this CRA by Large Load Customer.  Large Load Customer shall pay the Early 
Termination Amount calculated under Section 9.7 and Exhibit D. Termination under this 
paragraph shall become effective upon the applicable withdrawal, abandonment, or refusal and 
shall not be subject to the 120-day notice period below.
After execution of the Final PJM Agreement, Large Load Customer may terminate this CRA 
before expiration of the Term by providing Transmission Owner and Eligible Customer with at 
least 120 days’ prior written notice. Notwithstanding the foregoing, termination shall not become 
effective unless and until (a) the Large Load Customer has paid in full the applicable Early 
Termination Amount or Partial Termination Amount, as determined pursuant to this CRA, or (b) 
Page 39

PDF page 88

if such amount remains unpaid, the Transmission Owner has drawn on the Credit Support and 
recovered the full amount of such unpaid Early Termination Amount or Partial Termination 
Amount.  
Large Load Customer shall pay the Early Termination Amount calculated under Section 9.7 and 
Exhibit D. 
Large Load Customer’s  obligation to pay the Early Termination Amount shall survive 
termination and remain secured by Credit Support until paid in full.
9.2
Partial Termination
Before execution of the Final PJM Agreement, a reduction by Large Load Customer or Eligible 
Customer in the amount of Firm Transmission Service requested through the PJM process shall 
constitute a Partial Termination.
Large Load Customer may permanently reduce a specified portion of the Firm Load 
Commitment by providing Transmission Owner and Eligible Customer with at least 120 days’ 
prior written notice and paying the Partial Termination Amount calculated under Section 9.8 and 
Exhibit D.
A Partial Termination shall become effective only after:  (i) PJM has approved, directed, or 
otherwise recognized the reduction to the extent required under the PJM Tariff; (ii) the Parties 
have executed an amendment to Exhibit A; and (iii) the amendment has become effective under 
applicable FERC requirements.
If the Large Load Facilities have not achieved the state of readiness necessary to take Firm 
Transmission Service corresponding to the applicable Firm Load Commitment by 120 days after 
each Service Date, such occurrence will constitute a Partial Termination.
9.3
Project Abandonment or Cessation
Each Party shall notify the other Parties within five (5) Business Days after becoming aware 
that:
(a) the Large Load Customer has determined that it will not construct or complete the 
Large Load Facilities or proceed with the applicable request for Firm Transmission 
Service;
(b) the Large Load Facilities have not achieved the state of readiness necessary to take 
Firm Transmission Service by 120 days after the initial Service Date;
(c) the Large Load Customer intends to permanently cease operations at the Large Load 
Facilities; or
(d) Eligible Customer intends to permanently cease taking Firm Transmission Service to 
serve the Large Load Facilities.
Upon notice or occurrence of an event described in this Section, Transmission Owner may 
terminate this CRA upon thirty (30) days’ written notice to the other Parties, and  Large Load 
Customer  shall pay the Early Termination Amount. Large Load Customer’s obligation to pay 
Page 40

PDF page 89

the Early Termination Amount shall survive termination and remain secured by Credit Support 
until paid in full.
9.4
Termination for Default
Transmission Owner may terminate this CRA upon written notice to other Parties if a Party:
(a) commits an Event of Default that is not capable of cure; or
(b) fails to cure an Event of Default within the applicable period under Article 8.
Upon termination, Large Load Customer shall pay:
(a) all Shortfall Amounts and other amounts accrued through the termination date;
(b) the Early Termination Amount; and
(c) any other amount due under this CRA, subject to the prohibition against duplicative 
recovery.
Transmission Owner may apply Credit Support or cash security to those amounts in accordance 
with Articles 6, 7 and 9.
9.5
Termination by Mutual Agreement
The Parties may terminate this CRA by mutual written agreement, subject to applicable FERC 
requirements.
Any such agreement shall specify the treatment of the Early Termination Amount, any 
outstanding Shortfall Amounts, and the remaining Credit Support provided by Large Load 
Customer.
9.6
Termination Due to Transmission Facility-Related Delay  
If any extension of a Service Date or Committed Revenue Contribution under the second 
paragraph of Section 5.5 results in a forecasted or actual extension of [Insert number of months] 
months or more to either the first  Service Date or any subsequent Service Date, Large Load 
Customer may, at its option, either (1) terminate this CRA; or (2) accept the timing and resulting 
adjustment to the applicable Service Date(s).
If Large Load Customer elects to terminate this CRA pursuant to this Section 9.6, Large Load 
Customer shall be responsible for paying an Early Termination Amount calculated pursuant to  
Exhibit D.  However, for purposes of determining the Applicable Termination Percentage under 
Exhibit D the number of days in any forecasted or actual extension to the Service Date or 
Committed Revenue Contribution shall not be counted.  
To invoke this termination right, Large Load Customer must provide written notice to 
Transmission Owner and Eligible Customer within 60 days of receipt of notice that any 
forecasted or actual extension will equal or exceed [Insert number of months] months.  
Moreover, Large Load Customer will not be permitted to invoke this termination right if the 
delay is caused in whole or part by Large Load Customer’s failure or lack of reasonable 
Page 41

PDF page 90

diligence in meeting its obligations under this Agreement or any other binding agreement, tariff, 
regulatory order or other legal requirement, as set forth in Section 5.5.
9.7
Early Termination Amount
The “Early Termination Amount” shall be calculated in accordance with Exhibit D. 
9.8
Partial Termination Amount
The “Partial Termination Amount” shall be calculated in accordance with Exhibit D.  After the 
Partial Termination becomes effective, the Committed Revenue Contribution and Credit Support 
Requirement shall be calculated using the remaining Firm Load Commitment, provided that the 
Credit Support Requirement shall continue to be based on 100% of the Projected Full Firm 
Transmission Service Benchmarks corresponding to that remaining Firm Load Commitment.
9.9
Early Termination Offset Amount
If the Early Termination Offset Amount is quantifiable when Transmission Owner issues the 
termination invoice, it shall be included as an Applicable Credit.
If the offset becomes quantifiable afterward, Transmission Owner shall reflect it in a subsequent 
reconciliation and promptly return any resulting excess payment to Large Load Customer.
Nothing in this Section requires Transmission Owner to market the Point of Delivery, solicit 
replacement load, modify its transmission planning or service processes, or enter into a service 
arrangement with another Person.
9.10
Invoice and Payment
Transmission Owner shall promptly invoice  Large Load Customer for the Early Termination 
Amount or Partial Termination Amount and provide reasonable substantiation of the calculation. 
For the avoidance of doubt, in the event that the Large Load Customer fails to timely pay an 
invoice for the Early Termination Amount or Partial Termination Amount, the Transmission 
Owner shall be permitted to draw on the Credit Support for the unpaid amount.  
9.11
Effect of Termination
Any full termination of this CRA for any reason shall result in (i) before execution of the Final 
PJM Agreement, withdrawal or cancellation of the applicable request for Firm Transmission 
Service; and (ii) after execution of the Final PJM Agreement, cancellation of the Firm 
Transmission Service taken by Eligible Customer on behalf of Large Load Customer and the 
related Transmission Service Agreement, except where FERC has accepted a replacement or 
substitute agreement that contains terms reasonably comparable to this CRA pursuant to PJM 
Tariff, Part VIII, Section 438(b).
A Partial Termination shall result in the corresponding reduction of the request for Firm 
Transmission Service or the Firm Transmission Service, as applicable.
Page 42

PDF page 91

For avoidance of doubt, termination of this CRA and related cancellation of Firm Transmission 
Service shall not prohibit Large Load Customer from seeking Firm Transmission Service in the 
future.
9.12
Crediting of Termination Amount
If the effective date of an Early Termination or Partial Termination occurs prior to the first 
Service Date and the Large Load Customer is required to pay an Early Termination Amount or 
Partial Termination Amount, as applicable, such amount shall first be applied to the Project 
Development Costs as of the effective date of such termination in accordance with PJM Tariff, 
Part VIII, Subpart N, section 441(e).  Any remaining amounts from the applicable Termination 
Amount shall be credited to the Transmission Owner's Transmission Revenue Requirement for 
the Transmission Zone in which the Eligible Customer would have taken Transmission Service. 
For the avoidance of doubt, if Transmission Owner allocates any of the applicable Termination 
Amount to the Project Development Costs, such amount shall not be recovered in Transmission 
rates.  
 
If the effective date of an Early Termination or Partial Termination occurs on or after the first 
Service Date and the Large Load Customer is required to pay an Early Termination Amount or 
Partial Termination Amount, as applicable, such amount shall be credited to the Transmission 
Owner's Transmission Revenue Requirement for the Transmission Zone in which the Eligible 
Customer would have taken Firm Transmission Service. 
ARTICLE 10
ASSIGNMENT
10.1
Assignment by Eligible Customer
Eligible Customer may not assign or transfer this CRA, or any right or obligation arising under 
this CRA, in whole or in part, without the prior written consent of Transmission Owner and 
Large Load Customer, which consent shall not be unreasonably withheld, conditioned, or 
delayed.
Notwithstanding the foregoing, Eligible Customer may assign its rights and obligations under 
this CRA to an Affiliate without Transmission Owner’s prior written consent, if:
(a) Eligible Customer provides the other Parties with prior written notice of the proposed 
assignment;
(b) the proposed assignee is an Eligible Customer under the PJM Tariff and is authorized 
to take Firm Transmission Service on behalf of the Large Load Customer;
(c) the proposed assignee assumes in writing all obligations of Eligible Customer under 
this CRA;
(d) the assignment has received any acceptance, approval, or recognition required from 
PJM or FERC; and
(e) all disputes between Transmission Owner and existing Eligible Customer as to 
invoice outstanding have been reconciled.
Page 43

PDF page 92

An assignment by Eligible Customer shall not change Large Load Customer’s status or release, 
reduce, or otherwise modify Large Load Customer’s obligations under this CRA.
An assignment shall not become effective until all applicable requirements of this Section have 
been satisfied.
10.2
Effect of Assignment
Except as expressly provided in a written assignment agreement accepted by Transmission 
Owner and Large Load Customer, an assignment shall not release the assigning Eligible 
Customer from: (i) any breach or Event of Default occurring before the effective date of 
assignment; (ii) any obligation arising from information, service, or conduct occurring before the 
effective date of assignment but calculated or invoiced afterward; or (iii) any obligation that 
expressly survives assignment.
After the effective date of a permitted assignment, the assignee shall be treated as the Eligible 
Customer for purposes of this CRA and shall perform all obligations
assigned to Eligible 
Customer under this CRA on and after the effective date of assignment.
10.3
Assignment by Large Load Customer
Large Load Customer may not assign or transfer this CRA or any right or obligation arising 
under this CRA, in whole or in part, without the prior written consent of Transmission Owner 
and Eligible Customer, which consent shall not be unreasonably withheld, conditioned, or 
delayed.
An assignment by Large Load Customer shall not become effective unless:
(a) the proposed assignee assumes in writing all obligations of Large Load Customer 
under this CRA;
(b) compliant replacement Credit Support is provided that directly secures the proposed 
assignee’s obligations under this CRA;
(c) the assignment is documented through a written amendment or assignment executed 
by the applicable Parties;
(d) the assignment has received any acceptance, approval, or recognition required from 
PJM or FERC; and
(e) All disputes between Transmission Owner and existing Large Load Customer as to 
invoice outstanding have been reconciled.
A transfer of ownership, operation, leasehold rights, or control of the Large Load Facilities does 
not, by itself, assign this CRA or release Large Load Customer from its obligations under this 
CRA.
10.4
Assignment by Transmission Owner
Transmission Owner may assign this CRA, in whole or in part, without the other Parties’ 
consent:  (i) to a successor to all or substantially all of the transmission assets or obligations 
relevant to this CRA; (ii) in connection with a merger, consolidation, reorganization, or other 
corporate transaction; (iii) to an Affiliate that assumes Transmission Owner’s obligations under 
Page 44

PDF page 93

this CRA; or (iv) as required or authorized by the PJM Tariff, FERC, or another governmental 
authority with jurisdiction.
Transmission Owner shall provide the other Parties with written notice of the assignment.
Any other assignment by Transmission Owner requires the prior written consent of the other 
Parties, which consent shall not be unreasonably withheld, conditioned, or delayed.
ARTICLE 11
REGULATORY PROVISIONS
11.1
Regulatory Effectiveness
This CRA shall be submitted, reported, designated, posted, or filed only to the extent required by 
the PJM Tariff, a FERC order, regulation, or applicable law.
Completion of project-specific information, dates, amounts, percentages, schedules, and other 
elections expressly contemplated by the FERC-accepted form of CRA shall not constitute a 
nonconforming term or condition.
Updates to Exhibits A and C and calculations under Exhibit B required under Section 3.2 are 
expressly contemplated by this CRA and shall not constitute nonconforming terms or 
amendments, except to the extent a further filing with or acceptance by FERC is required.
11.2
Required FERC Filing
If this CRA is required to be filed with FERC under the PJM Tariff, a FERC order, or applicable 
law, Transmission Owner shall submit this CRA for acceptance under Section 205 of the Federal 
Power Act in accordance with PJM Tariff, Part VIII, Subpart N.
Transmission Owner shall take the lead in preparing and prosecuting the filing and shall use 
reasonable efforts to obtain FERC’s acceptance of this CRA.
Each Party shall reasonably cooperate in connection with the filing and refrain from taking a 
position inconsistent with the acceptance of this CRA, except as required by applicable law or 
expressly permitted under this CRA.
Each Party shall bear its own costs incurred in connection with the filing unless the Parties 
otherwise agree in writing.
11.3
Relationship to Other Tariffs and Agreements
Nothing in this CRA shall be construed to grant, provide, guarantee, or otherwise convey 
transmission service under the PJM Tariff, distribution or retail service under state-regulated 
tariffs or agreements, or any other service or rate, term or condition of such service, except as 
expressly provided herein. 
Page 45

PDF page 94

Nothing in this CRA limits any obligation under the PJM Tariff or another applicable agreement 
to pay study costs, directly assigned facility costs, Network Upgrade costs, or other costs 
associated with transmission service.
ARTICLE 12
FORCE MAJEURE
12.1
Definition and Scope of Force Majeure
“Force Majeure” means an event or circumstance that:
(a) physically and directly impacts the Large Load Facilities, new transmission facilities, 
or modifications to existing transmission facilities, and/or 
(b) prevents the Affected Party from performing its obligations under this CRA, 
which event or circumstance (i) could not have been  reasonably anticipated as of the Effective 
Date and (ii) which is not within the reasonable control of, or the result of negligence or 
misconduct by, the Affected Party, and (iii) which the Affected Party is unable to overcome or 
avoid or cause to be avoided, by the exercise of reasonable care.  Subject to meeting the 
requirements of the prior sentence, Force Majeure events shall include, but not be limited to, acts 
of God; fire; flood; earthquake; war; explosions; labor disputes; lightning; hurricanes; tornadoes; 
pandemics or epidemics; riots; or acts of terrorism that affect one or more Parties.  With respect 
to a Party’s obligation to make payments hereunder, Force Majeure will be only an event or act 
that on any day disables the banking system through which a Party makes such payments.  
Nothing herein shall be construed so as to require a Party to settle any strike or labor dispute in 
which it may be involved.  Economic hardship of any Party shall not constitute a Force Majeure 
under this CRA, even if that economic hardship is caused by an event or condition that would 
have been a Force Majeure event if it has physically and directly impacted the Large Load 
Facilities, new transmission facilities, or modifications to existing transmission facilities.
No event affecting only the Large Load Customer, the Large Load Facilities, or the amount of 
Firm Transmission Service taken to serve the Large Load Facilities shall constitute Force 
Majeure with respect to Large Load Customer’s payment or Credit Support obligations under 
this CRA.
The Party claiming Force Majeure bears the burden of establishing that the event satisfies every 
requirement of this Section.
If a Party is rendered unable, wholly or in part, by Force Majeure to carry out its obligations with 
respect to this CRA (the “Affected Party”), then the obligations of the Affected Party will, to the 
extent they are affected by such Force Majeure event, be suspended during the period of time 
that the Force Majeure event renders the Affected Party unable, wholly or in part, to carry out its 
obligations.  The Affected Party will not be liable for breach of this CRA due to a Force Majeure 
event nor shall the Affected Party be liable to the other Parties for, or on account of, any loss, 
damage, injury, or expense resulting from, or arising out of such Force Majeure event.  The 
Affected Party must give written notice and full particulars of such Force Majeure event as soon 
Page 46

PDF page 95

as practical after the occurrence of the Force Majeure event.  If a Force Majeure event continues 
for over 180 days in the aggregate during any 12 month period, the Parties will meet and in good 
faith attempt to renegotiate the terms and conditions of this CRA to address and account for the 
Force Majeure event.  If the Parties are thereafter unable to mutually agree in writing on an 
amendment to this CRA to address issues arising out of the Force Majeure event, Transmission 
Owner or Large Load Customer may terminate this CRA upon ten (10) days’ written notice to 
the other Parties, subject to Section 12.2, Article 9, and any obligations that accrued or survive 
under this CRA.
12.2
Termination Due to Force Majeure   
In the event that Large Load Customer terminates this Agreement pursuant to Section 12, the 
Large Load Customer shall remain obligated to pay the Early Termination Amount.  However, if 
the Transmission Owner terminates this Agreement pursuant to Section 12, Large Load 
Customer shall not be required to pay the Early Termination Amount.
12.3
Effect of Force Majeure
If a Party is prevented by Force Majeure from performing an obligation under this CRA, that 
obligation shall be suspended only:  (i) to the extent performance is physically impossible 
because of the Force Majeure; (ii) for the period during which performance remains physically 
impossible; and (iii) while the affected Party complies with Section 12.4.
The affected Party shall not be in breach of this CRA solely because it fails to perform an 
obligation properly suspended under this Section.
Force Majeure does not:
(a) excuse or delay an obligation to pay an amount due under this CRA, except solely to 
the extent expressly provided in Section 12.1;
(b) excuse or delay Large Load Customer’s obligation to cause Credit Support to be 
provided, maintained, increased, renewed, replaced, or replenished;
(c) except for an extension of a Service Date expressly permitted under Section 5.5, 
reduce, defer, or otherwise modify the Firm Load Commitment, any Service Date, or the 
Minimum Commitment Percentage;
(d) reduce or defer the calculation of the Committed Revenue Contribution, Actual 
Revenue Contribution, Shortfall Amount, Early Termination Amount, or Partial 
Termination Amount;
(e) excuse Eligible Customer’s failure to take Firm Transmission Service corresponding 
to the Firm Load Commitment;
(f) require Transmission Owner to release or reduce Credit Support;
(g) prevent Transmission Owner from issuing an invoice, completing a calculation or 
reconciliation, or drawing on Credit Support in accordance with this CRA; 
(h) excuse any obligation that arose before the Force Majeure began; or
(i) affect the application of Article 9 to any abandonment, permanent cessation, 
permanent reduction, or termination associated with the Force Majeure.
For the avoidance of doubt, a Force Majeure affecting the Large Load Customer, the Large Load 
Page 47

PDF page 96

Facilities, or the amount of Firm Transmission Service taken to serve the Large Load Facilities 
shall not reduce, defer, or otherwise modify Large Load Customer’s payment or Credit Support 
obligations under this CRA. If circumstances associated with a Force Majeure result in 
abandonment, permanent cessation, permanent reduction, or termination, Article 9 shall govern 
the availability, effectiveness, and financial consequences of that abandonment, cessation, 
reduction, or termination.
12.4
Notice
A Party claiming Force Majeure shall provide the other Parties with written notice as soon as 
reasonably practicable after becoming aware of the event.
Failure to provide timely notice shall not prevent an event from qualifying as Force Majeure, but 
the affected Party shall not be excused from performance to the extent the delay in notice 
materially prejudices  another Party.
ARTICLE 13
REPRESENTATIONS AND WARRANTIES
13.1
Mutual Representations and Warranties
Each Party represents and warrants to the other Parties, as of the date it executes this CRA and as 
of the Effective Date, that:
(a) it is duly organized, validly existing, and in good standing under the laws of its 
jurisdiction of organization, to the extent such concepts apply;
(b) it has the power and authority to execute, deliver, and perform this CRA;
(c) its execution by the Parties, delivery, and performance of this CRA have been duly 
authorized by all necessary organizational action;
(d) the individual executing this CRA on its behalf has authority to bind it;
(e) this CRA constitutes its legal, valid, and binding obligation, enforceable against it in 
accordance with its terms, subject to applicable bankruptcy, insolvency, reorganization, 
moratorium, and similar laws affecting creditors’ rights generally and to general 
principles of equity;
(f) its execution by the Parties, delivery, and performance of this CRA do not violate its 
organizational documents, applicable law, or any agreement binding on it in a manner 
that would materially impair its performance under this CRA; and
(g) except for any acceptance, approval, filing, or other action expressly contemplated by 
this CRA, the PJM Tariff, or applicable law, no consent or approval is required for its 
execution by the Parties, delivery, or performance of this CRA that has not been obtained 
or will not be obtained when required.
13.2
Eligible Customer Representations and Warranties
Eligible Customer represents and warrants to the other Parties, as of the date it executes this 
CRA and as of the Effective Date, that:
(a) it is an Eligible Customer under the PJM Tariff;
(b) it is authorized under the PJM Tariff and applicable law to take Firm Transmission 
Page 48

PDF page 97

Service on behalf of the Large Load Customer to serve the Large Load Facilities;
(c) it has obtained, or will obtain when required, all authority, consent, and information 
necessary to perform its obligations under this CRA;
(d) all information provided by or on behalf of Eligible Customer for purposes of 
calculating the Actual Revenue Contribution, Shortfall Amount, Credit Support 
Requirement, Early Termination Amount, or Partial Termination Amount is and shall be 
materially accurate and complete;
(e) it has not relied on any representation or warranty by Transmission Owner concerning 
whether the Large Load Facilities shall be constructed, completed, achieve commercial 
operation, operate at any load level, or remain economically viable;
(f) it will provide or authorize access to the service, billing, settlement, and allocation 
information reasonably necessary to administer this CRA;
(g) Eligible Customer’s obligations under this CRA are limited to the transmission-
service, information-sharing, cooperation, and administrative obligations expressly 
assigned to Eligible Customer and do not include Large Load Customer’s payment or 
Credit Support obligations; 
(h) Eligible Customer shall timely perform its expressly assigned obligations 
notwithstanding any dispute with Large Load Customer; 
(i) it has agreed to request and pursue the Firm Transmission Service initially identified 
in Exhibit A on behalf of Large Load Customer through the applicable PJM process; and
(j) neither the failure of the Large Load Customer to perform nor a dispute between 
Eligible Customer and the Large Load Customer will excuse Eligible Customer’s 
performance under this CRA.
13.3
Large Load Customer Representations and Warranties
Large Load Customer represents and warrants to the other Parties, as of the date it executes this 
CRA and as of the Effective Date, that:
(a) it owns, operates, leases, or otherwise controls the Large Load Facilities;
(b) the information it provides concerning the Large Load Facilities, Firm Load
Commitment, Service Dates, load ramp, construction status, anticipated operations, and 
cessation or reduction of operations, and any other information required by or necessary 
to administer this CRA is and shall be materially accurate and complete;
(c) it has not relied on any representation or warranty by Transmission Owner concerning 
whether the Large Load Facilities will be constructed, completed, achieve commercial 
operation, operate at any load level, or remain economically viable; 
(d) its payment and Credit Support obligations under this CRA are direct obligations to 
Transmission Owner and do not depend on the performance of Eligible Customer or any 
other Person; 
(e) Credit Support provided under Article 6 directly secures Large Load Customer’s 
obligations under this CRA and, to Large Load Customer’s knowledge, is valid and 
enforceable in accordance with its terms; 
(f) it has designated Eligible Customer to request and take Firm Transmission Service on 
its behalf and has obtained Eligible Customer’s agreement to participate in the applicable 
PJM process; and
Page 49

PDF page 98

(g) Large Load Customer has not created or permitted any undisclosed lien, competing 
claim, restriction, or other interest that would materially impair Transmission Owner’s 
rights in the Credit Support.
13.4
Transmission Owner Representations and Warranties
Transmission Owner represents and warrants to the other Parties, as of the date it executes this 
CRA and as of the Effective Date, that:  (i) it is a PJM Transmission Owner; (ii) it is authorized 
to enter into this CRA and receive amounts and Credit Support payable or provided under this 
CRA, subject to the PJM Tariff and applicable FERC requirements.
ARTICLE 14
CONFIDENTIALITY
14.1
Confidential Information
For purposes of this Article, “Confidential Information” means nonpublic commercial, financial, 
operational, technical, customer-specific, or proprietary information disclosed by or on behalf of 
one Party to  another Party in connection with this CRA, whether disclosed orally, electronically, 
or in writing, including nonpublic information concerning:
(a) the Large Load Customer or the Large Load Facilities;
(b) the Firm Load Commitment, Service Dates, anticipated or actual load, or operating 
status of the Large Load Facilities;
(c) Firm Transmission Service taken to serve the Large Load Facilities;
(d) the calculation of the Actual Revenue Contribution, Shortfall Amount, Credit Support 
Requirement, Early Termination Amount, or Partial Termination Amount;
(e) Credit Support, the financial condition of Large Load Customer , and communications 
with an issuer; and
(f) any invoice, supporting documentation, or other information exchanged in 
administering this CRA.
Information shall constitute Confidential Information only if:  (i) it is identified as confidential 
when disclosed; or (ii) its nature or the circumstances of disclosure would reasonably indicate 
that it is confidential.
14.2
Exclusions
Confidential Information does not include information that the receiving Party can demonstrate:  
(i) is or becomes publicly available other than through a breach of this CRA; (ii) was lawfully 
known to the receiving Party without a confidentiality restriction before disclosure by the 
disclosing Party; (iii) is lawfully received from another Person without a confidentiality 
restriction and without breach of an obligation owed to the disclosing Party; (iv) is independently 
developed by or for the receiving Party without use of or reliance on the Confidential 
Information; or (v) is approved for disclosure by the disclosing Party in writing.
14.3
Use and Protection of Confidential Information
Page 50

PDF page 99

A Party receiving Confidential Information shall:  (i) use the Confidential Information only as 
reasonably necessary to perform, administer, enforce, or exercise its rights under this CRA; (ii) 
protect the Confidential Information using at least the same degree of care that it uses to protect 
its own confidential information of a similar nature, but in no event less than reasonable care;
(iii) disclose the Confidential Information only as permitted under this Article; and (iv) promptly 
notify the disclosing Party upon becoming aware of an unauthorized use or disclosure of the 
Confidential Information.
The receiving Party may disclose Confidential Information to its Affiliates, employees, officers, 
directors, attorneys, accountants, auditors, consultants, insurers, lenders, issuers of Credit 
Support, and other representatives that have a need to know the Confidential Information and are 
subject to confidentiality obligations or professional duties of confidentiality.
14.4
Tariff and Regulatory Requirements
Confidential Information shall be protected and disclosed in accordance with:  (i) applicable 
FERC regulations and orders; (ii) applicable state law and any applicable retail-service tariff;
(iii) any protective order or confidentiality agreement binding on the Parties; and (iv) this 
Article.
14.5
Permitted Regulatory and Administrative Disclosures
A Party may disclose Confidential Information to the extent reasonably necessary:  (i) to comply 
with the PJM Tariff, a FERC order, applicable law, legal process, or a request or requirement of 
a governmental authority with jurisdiction; (ii) to prepare, submit, support, or prosecute a filing, 
report, audit, formula-rate update, rate proceeding, tariff proceeding, or other regulatory 
submission; (iii) to administer a service request, study, billing determination, settlement, 
calculation, reconciliation, or Credit Support requirement relating to this CRA; (iv) to enforce 
this CRA or resolve a dispute arising under it; (v) to provide information to PJM reasonably 
necessary for Tariff administration, study, billing, settlement, or other administrative purposes 
relating to the Firm Transmission Service or this CRA; (vi) to provide information to an 
applicable state regulatory authority to the extent reasonably necessary in connection with retail 
service, retail Credit Support, or another state-jurisdictional arrangement relating to the Large 
Load Facilities; or (vii) with the written consent of the disclosing Party.
With respect to disclosures identified in clauses (i)-(vi), the Party making the disclosure shall 
notify the other Party so that such Party may seek a protective order or such other relief as such 
Party may deem appropriate under the circumstances. The Party making the disclosure may 
disclose only that portion of the Confidential Information which such Party is required to 
disclose.
14.6
No Limitation on Required Information Sharing
Eligible Customer may not withhold information reasonably required to calculate, verify, 
invoice, reconcile, or dispute an amount under this CRA solely because the information is 
Page 51

PDF page 100

confidential.
Large Load Customer may not withhold facility, project, load-ramp, operational, Credit Support, 
or other information within its possession or control that is reasonably required to administer this 
CRA solely because the information is confidential.
Transmission Owner’s receipt or use of such information shall remain subject to this Article and 
any other applicable confidentiality requirement.
14.7
Survival
The obligations under this Article shall survive expiration or termination of this CRA for five (5)
years; provided that (i) information constituting a trade secret shall remain protected for so long
as it qualifies as a trade secret under applicable law; and (ii) information protected for a longer 
period under applicable law, the PJM Tariff, a regulatory order, or a binding confidentiality 
agreement shall remain protected for that longer period.
ARTICLE 15
DISPUTE RESOLUTION
15.1
Notice of Dispute
A Party disputing an invoice, calculation, Credit Support Requirement, or other matter arising 
under this CRA shall provide the other Parties with written notice.  The disputing Party shall 
provide available supporting information reasonably necessary for the other Parties to evaluate 
the dispute.  A notice under this Section shall not excuse or delay performance except as 
expressly provided in this CRA. Notwithstanding the foregoing and for the avoidance of doubt, 
the Large Load Customer is not entitled to dispute resolution for its breach of Section 6.1.
15.2
Good-Faith Negotiation
Within ten (10) Business Days after receipt of a notice under Section 15.1, representatives of the 
Parties with responsibility for administering this CRA shall meet or confer and attempt in good 
faith to resolve the dispute.
If a Party does not request or participate in the Dispute resolution set forth in this Article 15 
within 10 Business Days following the delivered date of the written request initiating the 
process, such Party waives any further right to this Dispute resolution process.  The Dispute 
resolution process set forth in this Article 15 shall, in any event, be concluded within 30 days 
following the delivered date of the written request initiating the process or such longer period as 
the Parties may mutually agree.  Thereafter, any Party may exercise all remedies available at law 
or in equity under this CRA, including the initiation of court proceedings.
15.3
Continuation of Performance
While a dispute remains pending:
Page 52

PDF page 101

(a) each Party shall continue performing its obligations under this CRA to the maximum 
extent practicable;
(b) Large Load Customer shall timely pay each invoiced amount in accordance with 
Section 7.2, notwithstanding the dispute;
(c) Large Load Customer shall continue to cause Credit Support to be provided, 
maintained, increased, renewed, replaced, and replenished as required under Article 6;
(d) Transmission Owner may exercise its rights with respect to Credit Support in 
accordance with Articles 6 and 7; and
(e) no Party shall take action inconsistent with a final and binding determination 
resolving the dispute.
Payment or performance during a dispute shall not waive the paying or performing Party’s 
position or right to seek return of an overpayment or other appropriate relief.
15.4
No Suspension of Credit Support Rights
The initiation or pendency of a dispute shall not:  (i) prevent Transmission Owner from making a 
preservation draw under Section 6.4; (ii) suspend Transmission Owner’s right to draw on Credit 
Support for an invoiced amount not timely paid; (iii) relieve Large Load Customer of its
obligation to cause compliant Credit Support to be maintained; or (iv) extend the expiration, 
nonrenewal, replacement, or replenishment deadline applicable to Credit Support.
If the final resolution of a dispute determines that Large Load Customer paid, or Transmission 
Owner drew, more than the amount properly due, Transmission Owner shall return the excess to 
Large Load Customer or, if applicable, restore the excess Credit Support in accordance with 
Section 6.5.
If a Party receiving a written request to initiate the dispute-resolution process does not participate 
in that process within 10 Business Days after delivery of the written request, that Party waives its 
right to require completion of the informal dispute-resolution process before another Party 
pursues available remedies.  The dispute resolution process set forth in this Article 15 shall, in 
any event, be concluded within 30 days following the delivered date of the written request 
initiating the process or such longer period as the Parties may mutually agree.  
Thereafter, any Party may exercise all remedies available at law or in equity under this CRA, 
including the initiation of court proceedings.
ARTICLE 16
NOTICES
16.1
General Notices
All notices, demands, and other formal communications required or permitted under this CRA 
shall be in writing, and delivered to the applicable contacts identified in Section 16.2.
16.2
Notice Contacts
Page 53

PDF page 102

Eligible Customer
[Eligible Customer Name]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
With a copy to:
[Legal Department or Counsel]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
Large Load Customer,
[Large Load Customer Name]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
With a copy to:
[Legal Department or Counsel]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
Transmission Owner
[Transmission Owner Name]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
With a copy to:
[Legal Department or Counsel]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
Delivery of a copy shall not be required for a notice to become effective unless expressly stated 
Page 54

PDF page 103

otherwise in this CRA.
16.3
Credit Support Notices
All notices, demands, and communications concerning the issuance, amendment, increase, 
reduction, renewal, replacement, nonrenewal, expiration, disqualification, transfer, draw, or 
release of Credit Support shall also be delivered to the following designated Credit Support 
contacts:
Transmission Owner Credit Contact
[Name or Department]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
Large Load Customer Credit Contact
[Name or Department]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
Such notices may be sent by overnight courier, personal delivery, or electronic mail. A notice 
from an issuer shall be effective only if delivered as required by the letter of credit.
ARTICLE 17
GENERAL PROVISIONS
17.1
Amendment
This CRA may be amended only by a written instrument executed by authorized representatives 
of all Parties.
An amendment shall become effective only upon:  (i) acceptance or approval by FERC, if 
required; (ii) any approval or recognition required under the PJM Tariff; and (iii) satisfaction of 
any other requirement of applicable law.
An update to an Exhibit required under Section 3.2 shall not constitute an amendment for 
purposes of this Section.
17.2
Entire Agreement; Relationship to Other Agreements
This CRA and its Exhibits constitute the entire agreement between the Parties concerning the 
Firm Load Commitment and the payment, Credit Support, early-termination, and related 
administrative obligations established under this CRA.  
Page 55

PDF page 104

This CRA supersedes prior oral or written communications, negotiations, and understandings 
between the Parties concerning the subject matter of this agreement.  This CRA does not 
supersede or otherwise impact other agreements (which may include security or cost recovery 
provisions) that relate to the Large Load Facilities and that do not address matters set forth in this 
CRA related to Firm Load Commitments.
17.3
Severability
If a provision of this CRA is held invalid, unlawful, or unenforceable by FERC or another 
governmental authority or tribunal having jurisdiction, the remaining provisions shall remain in 
effect to the maximum extent permitted by law.
The Parties shall cooperate in good faith to replace the affected provision with a lawful and 
enforceable provision that preserves, to the greatest extent permitted by law, the original 
provision’s purpose and the economic protections established by this CRA.
If the affected provision cannot be replaced and its invalidity defeats the essential purpose of this 
CRA, the Parties’ rights shall be governed by the remaining enforceable provisions of this CRA 
and applicable law.
17.4
Governing Law
This CRA shall be governed by:  (i) federal law, including the Federal Power Act, and the PJM 
Tariff with respect to matters within federal jurisdiction; and (ii) the laws of the State of [State], 
without regard to its conflict-of-laws principles, with respect to matters not governed by federal 
law.
Nothing in this Section limits FERC’s jurisdiction or alters the allocation of jurisdiction between 
FERC, any state commission, and any court or other tribunal.
17.5
No Third-Party Beneficiaries
This CRA is entered into solely for the benefit of the Parties and their permitted successors and 
assigns.
Except as expressly provided in this CRA, no other Person, including PJM, another transmission 
customer, a Load Serving Entity, an issuer of Credit Support, or a governmental authority, shall 
have a right to enforce this CRA or be deemed a third-party beneficiary.
17.6
Relationship of the Parties
Nothing in this CRA creates or shall be construed to create:  (i) a partnership; (ii) a joint venture;
(iii) an agency relationship; (iv) a fiduciary relationship; or (v) an employment relationship
among any of the Parties..
Page 56

PDF page 105

17.7
Counterparts; Electronic Signatures
This CRA may be executed in any number of counterparts, each of which shall be deemed an 
original and all of which together shall constitute one instrument.
17.8
Indemnification
Eligible Customer and Large Load Customer shall, jointly and severally, to the fullest extent 
permitted by law, indemnify, defend upon request, and hold harmless Transmission Owner and 
its Representatives from and against all claims, damages, expenses, liabilities, and losses 
(including, without limitation, reasonable attorneys’ fees and expenses) asserted against, 
sustained, or incurred by Transmission Owner or its Representatives for any damage, harm, 
injury, or loss, of any kind, direct or indirect, to any property or person (including death), 
including, without limitation:
(a) claims for injuries or loss to employees of Transmission Owner, Eligible Customer,
Large Load Customer, or their respective Representatives, arising out of or relating to 
any act, omission, conduct, negligence or breach by Large Load Customer, or Eligible 
Customer, or their respective Representatives; 
(b) arising out of or relating to the work performed under or in connection with this CRA 
by Large Load Customer, Eligible Customer, or their respective Representatives;  and/or
(c) claims arising out of or relating to Large Load Customer’s, Eligible Customer’s, or 
their respective Representatives, contact or encounter with, compromise or disruption of, 
or loss or damage to any property of Transmission Owner or its Representatives’ 
property.  
Large Load Customer and Eligible Customer each specifically agree, to the fullest extent 
permitted by law, to assume liability for all personal injury claims brought by their respective 
employees or the employees of their respective Representatives in connection with this CRA and 
waive any limitation of liability defense based upon the applicable worker’s compensation law
and cases decided thereunder. Eligible Customer and Large Load Customer agree to indemnify 
and defend Transmission Owner and its Representatives from and against all such loss, expense 
damage or injury, including, without limitation, reasonable attorneys’ fees, which Transmission 
Owner’s Representatives may sustain as a result of personal injury claims by Eligible 
Customer’s or Large Load Customer’s employees or their respective Representatives’ employees 
or representatives.  
17.9
Enforcement Costs
Each of Eligible Customer and Large Load Customer shall reimburse Transmission Owner for 
all reasonable attorneys’ fees and expenses incurred in enforcing that Party’s obligations under 
this CRA, to the extent Transmission Owner prevails in the applicable action or proceeding. 
Notwithstanding the foregoing, Large Load Customer shall be solely responsible for all 
reasonable attorneys’ fees and expenses incurred by Transmission Owner in enforcing Large 
Load Customer’s payment or Credit Support obligations or collecting any amount due from 
Large Load Customer under this CRA.
Page 57

PDF page 106

17.10 Rules of Interpretation
The Parties intend that any grouping of words or phrases in a series of three or more shall be 
interpreted to include the use of the Oxford (or serial) comma regardless of whether such Oxford 
(or serial) comma is actually present in the series.
17.11 Survival
Expiration or termination of this CRA shall not affect:  (i) any payment obligation accrued or 
arising from a period before expiration or termination; (ii) any obligation to complete a 
calculation, invoice, reconciliation, refund, or return of an excess draw; (iii) any continuing right 
concerning Credit Support;  (iv) Large Load Customer’s obligation to pay any Shortfall Amount, 
Early Termination Amount, Partial Termination Amount, or other amount that survives 
expiration or termination; (v) Transmission Owner’s right to draw upon or apply Credit Support 
and its obligation to provide any required credit, refund, release, or reconciliation; (vi) the 
confidentiality and dispute-resolution provisions of Articles 14 and 15; or (vii) any other 
provision that expressly survives or that by its nature must survive to give effect to the Parties’ 
rights and obligations.
[Signature page follows]
Page 58

PDF page 107

IN WITNESS WHEREOF, the Parties, intending to be legally bound, have caused this CRA to 
be executed by their duly authorized representatives as of the date first written above.
TRANSMISSION OWNER:
[Name of Transmission Owner]
By: ______________________________
Name: ____________________________
Title: _____________________________
Date: _____________________________
ELIGIBLE CUSTOMER:
[Name of Eligible Customer]
By: ______________________________
Name: ____________________________
Title: _____________________________
Date: ____________________________
LARGE LOAD CUSTOMER:
[Name of Large Load Customer]
By: ______________________________
Name: ____________________________
Title: _____________________________
Date: _____________________________
Page 59

PDF page 108

EXHIBIT A
LARGE LOAD FACILITIES AND FIRM LOAD COMMITMENT
1.
Parties and Large Load Information
Transmission Owner:
[Name of Transmission Owner]
Eligible Customer:
[Name of Eligible Customer]
Large Load Customer:
[Name of Large Load Customer]
Large Load Facilities:
[Name and general description of the Large Load Facilities]
Facility Location:
[Street Address]
[City, State, ZIP Code]
Transmission Zone:
[Applicable PJM Transmission Zone]
Point of Delivery:
[Point of Delivery or other applicable delivery-point identifier]
2.
Term of Agreement: [__] Years
3.
Minimum Commitment Percentage:  [___] [add reduction schedule as 
applicable]%
4.
Initial Load and Firm Load Commitments
Eligible Customer’s Initial Load Commitment and Firm Load Commitment will be set forth in 
the following schedule:
Load-Ramp 
Stage
Service 
Date
Load Commitment / Associated Firm Transmission Service
Benchmark
1
[Date]
[___] MW
2
[Date]
[___] MW
Page 60

PDF page 109

3
[Date]
[___] MW
[Additional 
Stage]
[Date]
[___] MW
Final
[Date]
[___] MW
Following the update required under Section 3.2, the information in this Section 4 shall replace 
the Initial Load Commitment and shall establish the Firm Load Commitment for purposes of this
CRA.
The Firm Load Commitment applicable during any Measurement Period is the amount of total 
load from the Large Load Facilities that is anticipated to be in service under the foregoing 
schedule if the Eligible Customer is taking NITS on behalf of the Large Load.  If the Eligible 
Customer is taking FCDS or Firm Point-to-Point Transmission Service on behalf of the Large 
Load, the Firm Load Commitment applicable during any Measurement Period is the amount of 
such Firm Transmission Service for which the Eligible Customer has contracted or reserved, as 
applicable, during such period.
If a subsequent Service Date occurs during a Measurement Period, the Firm Load Commitment 
applicable before and after that Service Date shall be determined separately for the applicable 
portions of the Measurement Period in accordance with Exhibit B.
5.
Service Dates
The first Service Date under this Exhibit A is [Date].
The final Service Date under this Exhibit A is [Date].
6.
Commercial Operation Date
The anticipated Commercial Operation Date for the Large Load Facilities is [Date]. The 
anticipated Commercial Operation Date is not a guarantee of service on such date.
Except as expressly provided in the CRA, a change in the anticipated or actual Commercial 
Operation Date does not modify:
a Service Date;
the Firm Load Commitment;
the Committed Revenue Contribution;
the Credit Support Requirement; or
any other obligation under the CRA.
7.
Relationship to Actual Load and Firm Transmission Service
The Firm Load Commitment is a contractual benchmark reflecting the anticipated load 
associated with the Large Load Facilities and the corresponding Firm Transmission Service
Page 61

PDF page 110

commitment on which the CRA is based. It is not a statement of the Large Load Facilities' actual 
demand during any Measurement Period.
8.
Update and Amendment History
The following table will identify each update or amendment of this Exhibit A that becomes 
effective under Section 3.2 or Article 17 of the CRA:
Update or 
Amendment No.
Effective 
Date
Description of Update 
or Amendment
Final PJM Agreement Identifier or 
FERC Docket No./Order Date, as 
Applicable
[___]
[Date]
[Description]
[Final PJM Agreement Identifier or 
Docket No./Order Date]
[___]
[Date]
[Description]
[Final PJM Agreement Identifier or 
Docket No./Order Date]
[___]
[Date]
[Description]
[Final PJM Agreement Identifier or 
Docket No./Order Date]
An update required under Section 3.2 shall become effective without further agreement or 
signature of the Parties and shall not constitute an amendment to the CRA, except to the extent a 
filing with or acceptance by FERC is required. Any other change to this Exhibit A shall be made 
in accordance with Article 17.
Unless and until an update or amendment becomes effective in accordance with the CRA, the 
then-effective Firm Load Commitment and Service Dates will continue to control.
Page 62

PDF page 111

EXHIBIT B
REVENUE CONTRIBUTION AND SHORTFALL CALCULATION
1. Applicable Firm Load Commitment
For each Measurement Period, the “Applicable Firm Load Commitment” shall mean each 
amount of the Firm Load Commitment scheduled to apply during that Measurement Period 
under Exhibit A.
If more than one load level is scheduled to apply during a Measurement Period, each load level 
shall apply for the portion of the Measurement Period during which it is scheduled to be 
effective.
The Applicable Firm Load Commitment shall not be reduced or deferred based on:
the amount of load that actually materializes;
the amount of Firm Transmission Service actually taken to serve the Large Load 
Facilities; or
the actual operating level of the Large Load Facilities.
2. Full Firm Transmission Service Benchmark
For each Measurement Period, the “Full Firm Transmission Service Benchmark” shall equal 
100% of the Firm Transmission Service-related charges that would apply if Eligible Customer 
took Firm Transmission Service corresponding to the Applicable Firm Load Commitment during 
that Measurement Period.
The Full Firm Transmission Service Benchmark shall be calculated using:
the Applicable Firm Load Commitment;
the Applicable Firm Transmission Service Rate;
the generally applicable rate components and billing determinants used under the PJM 
Tariff and Transmission Owner’s applicable FERC-jurisdictional rate to calculate charges 
for  Firm Transmission Service; and
the portion of the Measurement Period during which each applicable load level and 
Applicable Firm Transmission Service Rate applies.
If the Applicable Firm Load Commitment or Applicable Firm Transmission Service Rate 
changes during a Measurement Period, the Full Firm Transmission Service Benchmark shall 
equal the sum of the amounts separately calculated for each applicable portion of the 
Measurement Period.
3. Committed Revenue Contribution
For each Measurement Period, the Committed Revenue Contribution = Minimum Commitment 
Percentage × Full Firm Transmission Service Benchmark
The Minimum Commitment Percentage shall be the percentage specified in Exhibit A.
Page 63

PDF page 112

The Minimum Commitment Percentage shall be applied only to the Full Firm Transmission 
Service Benchmark and shall not be applied to the Actual Revenue Contribution.
4. Actual Revenue Contribution
For each Measurement Period, the Actual Revenue Contribution shall equal the Firm 
Transmission Service-related revenues paid or payable to PJM for remittance or allocation to 
Transmission Owner, or otherwise paid or payable to Transmission Owner, that are attributable 
to transmission service actually taken to serve the Large Load Facilities.
The Actual Revenue Contribution shall include amounts to the extent those amounts:
are attributable to Firm Transmission Service taken by Eligible Customer to serve the 
Large Load Facilities;
correspond to the same categories of rate components included in the Full Firm 
Transmission Service Benchmark; and
have not been refunded, reversed, or otherwise credited to the payer.
To the extent the applicable Firm Transmission Service methodology uses an assigned 
Network Service Peak Load contribution or another allocated billing determinant, the 
Actual Revenue Contribution shall be calculated using:
the billing determinant assigned to the Large Load Facilities for the applicable 
Measurement Period; and
the same categories of rates and rate components used to calculate the Full Firm 
Transmission Service Benchmark.
5. Actual Billing Determinant and Allocation
If Firm Transmission Service-related charges or billing determinants attributable to the Large 
Load Facilities are aggregated with charges or billing determinants attributable to other load, 
Transmission Owner shall determine the portion attributable to the Large Load Facilities using, 
in the following order of priority:
PJM billing and settlement data that separately identifies the Large Load Facilities;
metering or other load data for the Large Load Facilities, applied in accordance with the 
generally applicable billing and allocation methodology under the PJM Tariff; and
if the foregoing information is insufficient, other information supplied by Eligible 
Customer or the applicable billing or service entity that Transmission Owner reasonably 
determines is sufficient to identify and verify the portion attributable to the Large Load 
Facilities.
Eligible Customer shall provide, or cause the applicable billing or service entity to provide, 
information reasonably necessary to identify and verify the portion attributable to the Large Load 
Facilities.
6. Included Rate Components
Page 64

PDF page 113

The same categories of Firm Transmission Service rate components shall be used to calculate the 
Full Firm Transmission Service Benchmark and the Actual Revenue Contribution.  The included 
rate components shall be derived from the applicable zonal Firm Transmission Service rate.
The following amounts shall be excluded:
charges for electric energy;
charges for generation capacity;
retail electric service or distribution-service charges;
penalties or charges for unreserved transmission use;
administrative-service or ancillary-service charges, unless expressly included above;
interest, late-payment charges, taxes, and fees unrelated to the included Firm 
Transmission Service rate components; and
amounts attributable to load other than the Large Load Facilities.
7. Applicable Firm Transmission Service Rate
The Applicable Firm Transmission Service Rate for each Measurement Period shall be the 
applicable zonal rate then in effect under the PJM Tariff and Transmission Owner’s FERC-
jurisdictional rate for Firm Transmission Service in the applicable Transmission Zone.
If an applicable zonal Firm Transmission Service Rate changes during a Measurement Period, 
each rate shall apply to the portion of the Measurement Period during which it was in effect.
8. Shortfall Amount
For each Measurement Period, the Shortfall Amount = Committed Revenue Contribution • 
Actual Revenue Contribution
If the Actual Revenue Contribution equals or exceeds the Committed Revenue Contribution, the 
Shortfall Amount shall be zero.
9. Separate Measurement Periods
Each Measurement Period shall be calculated independently. Any amount by which the Actual 
Revenue Contribution exceeds the Committed Revenue Contribution for one Measurement 
Period shall not reduce a Shortfall Amount for another Measurement Period, be carried forward 
or backward, or entitle Large Load Customer to any payment, refund, or credit.
10. Partial Measurement Periods
For any partial Measurement Period, the Full Firm Transmission Service Benchmark, Committed 
Revenue Contribution, Actual Revenue Contribution, and Shortfall Amount shall be calculated 
for the portion of the Measurement Period falling within the Term.
The Full Firm Transmission Service Benchmark shall be prorated in accordance with the billing 
interval applicable to the Applicable Firm Transmission Service Rate, based on the portion of the 
Page 65

PDF page 114

Measurement Period during which each applicable load level and Applicable Firm Transmission 
Service
Rate 
was 
effective.
Page 66

PDF page 115

EXHIBIT C
CREDIT SUPPORT REQUIREMENT AND SCHEDULE
1. Credit Support Requirement
The Credit Support Requirement is intended to secure Large Load Customer’s projected 
financial exposure under the CRA for the remaining Term and does not determine or limit any 
amount otherwise payable by Large Load Customer under the CRA.
At execution by the Parties, the Initial Credit Support Requirement shall be calculated using the 
Initial Load Commitment, anticipated Service Dates, estimated Applicable Firm Transmission 
Service Rate, and other information then available, and the methodology specified below. 
The Initial Credit Support Requirement shall equal the aggregate Projected Full Firm 
Transmission Service Benchmarks for the full Term of this CRA beginning on the first Service 
Date through the end of the Term.
Following the update required under Section 3.2 after execution of the Final PJM Agreement, 
Transmission Owner shall recalculate the Credit Support Requirement using the updated Firm 
Load Commitment, Service Dates, Applicable Firm Transmission Service Rate, and Projected 
Full Firm Transmission Service Benchmarks for the remainder of the Term. The recalculated 
Credit Support Requirement shall replace the Initial Credit Support Requirement.
At the end of each Measurement Period, Transmission Owner shall recalculate Large Load 
Customer’s Credit Support Requirement. The recalculation shall equal the aggregate Projected 
Full Firm Transmission Service Benchmarks for the remaining Term. Transmission Owner shall 
exclude a completed Measurement Period from the Credit Support Requirement only after:
(i) Transmission Owner has finally calculated the Committed Revenue Contribution, Actual 
Revenue Contribution, and any resulting Shortfall Amount for that Measurement Period; and
(ii) Large Load Customer has paid all amounts due for that Measurement Period.
Transmission Owner shall provide Large Load Customer with notice after each recalculation, 
and the revised Credit Support Requirement shall become effective in accordance with Section 
6.5 of the CRA. These recalculations shall not constitute an amendment to this Exhibit or the 
CRA.
2. Calculation of Projected Full Firm Transmission Service Benchmarks
For each Measurement Period included in the Credit Support Requirement, the Projected Full 
Firm Transmission Service Benchmark shall equal 100% of the Firm Transmission Service-
related charges that would apply if Eligible Customer took Firm Transmission Service 
corresponding to the Initial Load Commitment or Firm Load Commitment, as applicable, 
scheduled to apply during that Measurement Period.
The Credit Support Requirement shall equal the aggregate Projected Full Firm Transmission 
Service Benchmarks for all Measurement Periods included in the applicable calculation.
Page 67

PDF page 116

The Projected Full Firm Transmission Service Benchmark shall be calculated using:
the Initial Load Commitment or Firm Load Commitment, as applicable, and set forth in 
Exhibit A;
the Applicable Firm Transmission Service Rate in effect or estimated to apply, as 
applicable, at the time of calculation;
any rate change accepted by FERC and scheduled to become effective during the 
applicable Measurement Period;
the rate components and billing determinants identified in Exhibit B; and
the portion of each Measurement Period during which each applicable load level and 
Applicable Firm Transmission Service Rate is scheduled to apply.
3. No Reduction for Minimum Commitment Percentage or Projected Actual Revenues
The Credit Support Requirement shall be calculated using 100% of the Projected Full Firm 
Transmission Service Benchmarks and shall not be reduced by:
the Minimum Commitment Percentage; or
any projected or estimated Actual Revenue Contribution.
Actual Revenue Contributions shall be credited in determining the Shortfall Amount for a 
completed Measurement Period in accordance with Article 5 and Exhibit B.
After the calculation for a completed Measurement Period has been finalized and Large Load 
Customer has paid all amounts due for that Measurement Period, that Measurement Period shall 
be excluded from the Credit Support Requirement in accordance with Sections 1 and 4 of this 
Exhibit.
For avoidance of doubt, Actual Revenue Contributions attributable to a completed Measurement 
Period shall not reduce the Projected Full Firm Transmission Service Benchmark for any future 
Measurement Period.
4. Recalculation
Transmission Owner shall recalculate the Credit Support Requirement:
following the update required under Section 3.2 after execution of the Final PJM 
Agreement;
after the Committed Revenue Contribution, Actual Revenue Contribution, and any 
resulting Shortfall Amount for a completed Measurement Period have been finally 
calculated and Large Load Customer has paid all amounts due for that Measurement 
Period in accordance with Section 1 of this Exhibit;;
following an effective modification to the Firm Load Commitment or a Service Date;
following an effective Partial Termination;
following a change in the Applicable Firm Transmission Service Rate that has become 
effective, or a rate change that has been accepted by FERC and is scheduled to become 
effective during a Measurement Period included in the Credit Support Requirement; 
Page 68

PDF page 117

upon replacement of Credit Support following an issuer downgrade, disqualification, 
expiration, termination, or notice of nonrenewal; and
as otherwise expressly required under the CRA.
Transmission Owner shall provide notice of each such recalculation, and the revised Credit 
Support Requirement shall become effective in accordance with Section 6.5 of the CRA.  These 
updates shall not constitute an amendment to this Exhibit or the CRA generally.
5. Letter of Credit Issuer Requirements
A financial institution issuing a letter of credit under the CRA shall:
maintain a long-term unsecured credit rating of [at least “A-” from S&P Global Ratings 
or Fitch Ratings or “A3” from Moody’s Investors Service] [insert alternative credit rating 
requirement if applicable];
satisfy the requirements of Article 6 and any attachments to this Exhibit; and
otherwise satisfy Transmission Owner’s generally applicable credit requirements.
6. Treatment of Prior Draws
A draw applied to an unpaid amount shall not reduce the Credit Support Requirement. Large 
Load Customer shall cause the Credit Support to be restored to the then-applicable Credit 
Support Requirement in accordance with Section 6.7 of the CRA.
A preservation draw under Section 6.4 shall not reduce the Credit Support Requirement because 
the proceeds continue to be held as cash security securing Large Load Customer’s obligations 
under the CRA.
In determining the amount of replacement or additional Credit Support required, cash security 
held by Transmission Owner and legally available to secure the same obligations shall be 
credited against the otherwise applicable Credit Support Requirement.
7. Relationship to Amounts Payable
The Credit Support Requirement is a measure of secured exposure and does not determine or 
limit:
the actual Committed Revenue Contribution;
the Actual Revenue Contribution;
the Shortfall Amount for a completed Measurement Period; or
any amount otherwise payable under the CRA.
Page 69

PDF page 118

EXHIBIT C, ATTACHMENT [__]
Page 70

PDF page 119

EXHIBIT D
EARLY AND PARTIAL TERMINATION AMOUNT SCHEDULE
1. Applicable Termination Percentage
The Applicable Termination Percentage for an Early Termination or Partial Termination shall be 
determined based on the date on which the termination or Partial Termination becomes effective, 
as follows:
Effective Date of Termination or Partial Termination Applicable Termination Percentage
On or after the Effective Date and before execution of the 
Final PJM Agreement
25%
On or after execution of the Final PJM Agreement through 
the 180th day after execution of the Final PJM Agreement 50%
After the 180th day after execution of the Final PJM 
Agreement but before the first Service Date
75%
On or after the first Service Date
100%
2. Early Termination Amount
The Early Termination Amount shall be calculated in accordance with Article 9 and this Exhibit 
of the CRA as follows:
Early Termination Amount = (Applicable Termination Percentage × Present Value of Remaining 
Projected Committed Revenue Contributions) • Applicable Credits 
The Applicable Termination Percentage used in the calculation shall be the percentage specified 
in Section 1 of this Exhibit for the date on which the termination becomes effective.
Before execution of the Final PJM Agreement, the Early Termination Amount shall be calculated 
using the Initial Load Commitment, anticipated Service Dates, estimated Applicable Firm 
Transmission Service Rate, and other information then reflected in Exhibits A and C. After 
execution of the Final PJM Agreement, the calculation shall use the updated information 
provided pursuant to Section 3.2.
The Early Termination Amount shall not be less than zero.
3. Present Value of Remaining Projected Committed Revenue Contributions
The Present Value of Remaining Projected Committed Revenue Contributions shall be 
calculated as of the effective date of termination for the period beginning on the effective date of 
termination and ending on the date the fixed period specified in Section 4.2(i) of the CRA would 
have expired absent the termination.
Page 71

PDF page 120

The calculation shall be based on:
the Initial Load Commitment or Firm Load Commitment, as applicable, and Service 
Dates in effect immediately before termination;
the Minimum Commitment Percentage;
the Projected Full Firm Transmission Service Benchmark determined in accordance with 
Exhibit C;
the Applicable Firm Transmission Service Rate in effect or estimated to apply, as 
applicable, on the effective date of termination; 
any rate change accepted by FERC and scheduled to become effective during the 
remaining fixed period;
the rate components and billing determinants identified in Exhibit B; and
Transmission Owner’s then-effective FERC-approved weighted average cost of capital as 
the discount rate.
No rate escalation or other projected rate change shall be included unless the rate change has 
been accepted by FERC and is scheduled to become effective during the remaining fixed period.
4. Applicable Credits
Applicable Credits shall include, without duplication:
any Actual Revenue Contribution attributable to the portion of the Measurement Period 
occurring before the effective date of termination that has been paid or is payable and has 
not otherwise been credited;
any Shortfall Amount, Credit Support proceeds, or other amount previously collected and 
applied to the same revenue exposure; and
any Early Termination Offset Amount determined under Section 9.9 of the CRA.
No amount shall be treated as an Applicable Credit unless it has been paid, received, or applied 
to the revenue exposure included in the Early Termination Amount.
5. Partial Termination Amount
Unless the permanently reduced portion of the Firm Load Commitment consists of a separately 
identifiable load tranche, the Partial Termination Amount shall equal:
Partial Termination Amount = Early Termination Amount × (Permanently Reduced MW ÷ 
applicable Initial Load Commitment or Firm Load Commitment immediately before reduction) 
The Applicable Termination Percentage shall be the percentage specified in Section 1 of this 
Exhibit for the effective date of the Partial Termination.
If the permanently reduced portion consists of one or more separately identifiable load tranches, 
the Partial Termination Amount shall be calculated using the Projected Committed Revenue 
Contributions attributable to the terminated tranche or tranches, including the applicable MW 
amount and Service Date for each terminated tranche.
Page 72

PDF page 121

The Partial Termination Amount shall not be less than zero.
6. Treatment After the First Service Date
On and after the first Service Date, the Applicable Termination Percentage shall remain 100%.
The Present Value of Remaining Projected Committed Revenue Contributions will decline as the 
remaining portion of the fixed period decreases. Accordingly, the Applicable Termination 
Percentage will not be separately reduced based solely on the passage of time after the first 
Service Date.
7. Early Termination Offset Amount
If an Early Termination Offset Amount is quantifiable when Transmission Owner issues the 
applicable termination invoice, Transmission Owner shall include that amount as an Applicable 
Credit.
If all or part of the Early Termination Offset Amount becomes quantifiable after the termination 
invoice is issued, Transmission Owner shall reflect the amount in a subsequent reconciliation and 
promptly return any resulting excess payment to Large Load Customer in accordance with 
Articles 7 and 9 of the CRA.
Nothing in this Exhibit requires Transmission Owner to market the Point of Delivery, solicit 
replacement load, modify its transmission planning or service processes, or enter into a 
transmission-service arrangement with another Person.
8. No Duplicate Recovery
The Early Termination Amount and Partial Termination Amount are forward-looking amounts 
intended to address projected revenue exposure arising after the effective date of termination or 
Partial Termination.
Transmission Owner shall not recover the same revenue exposure through both:
a Shortfall Amount; and
an Early Termination Amount or Partial Termination Amount.
Amounts collected before termination or Partial Termination shall be credited only to the extent 
required under Article 9 and this Exhibit to prevent duplicate recovery.
Page 73

PDF page 122

706
Rates and Charges
Eligible Customers taking Interim Network Integration Transmission Service shall pay the 
charges set forth in this Section 706.
706.1 Monthly Demand Charge
Eligible Customer shall pay a Monthly Demand Charge for Zone Network Load and Non-Zone 
Network Load, which shall be determined as follows: Eligible Customer’s measured demand 
amount (in MWs) multiplied by the applicable zonal Network Integration Transmission Service 
rate established pursuant to Section 34.1.
Revenue Crediting.  Each month, revenue credits will be applied to the gross monthly Demand 
Charge to determine the actual charge to the Transmission Customer.  Revenue credits shall be 
calculated based on the sum of the applicable Zone’s share of revenues collected during the 
month from the Non-Firm Contract Demand Charge under Schedule 19.  The sum of these 
revenues will appear as a reduction to the gross monthly rate stated above on a Transmission 
Customer’s bill in that month for service under this schedule.  
706.2 Redispatch Charge
The Eligible Customer shall pay any redispatch costs as set forth in Tariff, Attachment K.
706.3 Stranded Cost Recovery
Any Transmission Owner may seek to recover stranded costs from the Eligible Customer 
pursuant to this Tariff in accordance with the terms, conditions and procedures set forth in FERC 
Order No. 888.  However, the Transmission Owner must separately file any proposal to recover 
stranded costs under section 205 of the Federal Power Act.
706.4 Other Charges
Eligible Customer shall pay administrative services charges under Tariff, Schedule 1A; Tariff, 
Schedule 9; and Tariff, Schedule 10, consistent with the charges assessed to loads taking 
Network Integration Transmission Service.
Eligible Customer shall pay Ancillary Services charges in accordance with Tariff, Part I, 
section 3. 
Eligible Customer shall pay Black Start Service charges in accordance with Tariff, Schedule 6A.
Page 74

PDF page 123

714 
Rates and Charges for Firm Contract Demand Transmission Service
Eligible Customers taking Firm Contract Demand Transmission Service on behalf of Eligible 
Load or Large Load shall pay the charges set forth in this Section 714.
714.1 Monthly Demand Charge
Eligible Customer taking service on behalf of Eligible Load or Large Load shall pay a Monthly 
Demand Charge based on the Firm Contract Demand Transmission Service amount (MW), as 
specified in Eligible Customer’s Service Agreement, in accordance with Tariff, Schedule 18.
Page 75

PDF page 124

715 
Rates and Charges for Non-Firm Contract Demand Transmission Service
Eligible Customers taking Non-Firm Contract Demand Transmission Service shall pay the 
charges set forth in this Section 715.
715.1 Monthly Demand Charge
Eligible Customer shall pay a discounted reservation rate set as a function of the Zonal Firm 
Contract Demand Transmission Service rate and the transmission system load factor for a Zone, 
as specified in Eligible Customer’s Service Agreement, in accordance with Tariff, Schedule 19.
Page 76

PDF page 125

SCHEDULE 7
Long-Term Firm and Short-Term Firm Point-To-Point
Transmission Service
1) The Transmission Customer shall pay each month for Reserved Capacity at the sum of the applicable charges set forth below for the Point of Delivery:
Summary of Charges
(in $/kW)
Point of Delivery
Yearly Charge
Monthly Charge
Weekly Charge
Daily On-Peak1/
Charge
Daily Off-Peak2/
Charge
Border of PJM3/
Border Yearly Charge 
established pursuant to 
section 11 below
Yearly Charge /12
Yearly Charge /52
Weekly Charge /5
Weekly Charge /7
AE Zone
23.809
1.984
0.4580
0.0920
0.0650
BGE Zone
15.675
1.306
0.3010
0.0600
0.0430
Delmarva Zone
19.378
1.615
0.3730
0.0750
0.0530
JCPL Zone
15.112
1.259
0.2906
0.0581
0.0414
MetEd Zone
15.112
1.259
0.2906
0.0581
0.0414
Penelec Zone
15.112
1.259
0.2906
0.0581
0.0414
PECO Zone
26.264
2.189
0.5051
0.1010
0.0722
PPL Zone: Total charge is the sum of 
the components
PPL: *
AEC: 0.463
UGI: *
PPL: *
AEC: 0.039
UGI: *
PPL: *
AEC: 0.0089
UGI: *
PPL: *
AEC: 0.0018
UGI: *
PPL: *
AEC: 0.0013
UGI: *
Page 77

PDF page 126

Point of Delivery
Yearly Charge
Monthly Charge
Weekly Charge
Daily On-Peak1/
Charge
Daily Off-Peak2/
Charge
Pepco Zone
20.999
1.750
0.4040
0.0810
0.0580
PSE&G Zone
23.696
1.975
0.4557
0.0911
0.0651
AP Zone
Rate Pursuant to Attachment H-
11 and Attachment H-34
Rate Pursuant to 
Attachment H-11 and 
Attachment H-34
Rate Pursuant to Attachment 
H-11 and Attachment H-34
Rate Pursuant to Attachment 
H-11 and Attachment H-34
Rate Pursuant to 
Attachment H-11 and 
Attachment H-34
Rockland Zone
53.766
4.481
1.0340
0.2068
0.1477
ComEd Zone4/
5/
AEP East Zone6/
Rate Pursuant to 
Attachment H-14 and 
Attachment H-20
Rate Pursuant to 
Attachment H-14 and 
Attachment H-20
Rate Pursuant to Attachment 
H-14 and Attachment H-20
Rate Pursuant to Attachment 
H-14 and Attachment H-20
Rate Pursuant to 
Attachment H-14 and 
Attachment H-20
Dayton Zone
Rate Pursuant to 
Attachment H-15
Rate Pursuant to 
Attachment H-15
Rate Pursuant to Attachment 
H-15
Rate Pursuant to Attachment 
H-15
Rate Pursuant to 
Attachment H-15
Duquesne Zone
14.17
1.18
0.27
0.0540
0.0386
Dominion Zone7/
ATSI Zone
Rate Pursuant to 
Attachment H-21
Rate Pursuant to 
Attachment H-21
Rate Pursuant to 
Attachment H-21
Rate Pursuant to 
Attachment H-21
Rate Pursuant to 
Attachment H-21
DEOK Zone
Rate Pursuant to 
Attachment H-22
Rate Pursuant to 
Attachment H-22
Rate Pursuant to 
Attachment H-22
Rate Pursuant to 
Attachment H-22
Rate Pursuant to 
Attachment H-22
EKPC Zone
Rate Pursuant to 
Attachment H-24
Rate Pursuant to 
Attachment H-24
Rate Pursuant to 
Attachment H-24
Rate Pursuant to 
Attachment H-24
Rate Pursuant to 
Attachment H-24
Page 78

PDF page 127

OVEC Zone
5.16
0.43
0.10
0.02
0.014
* PPL Electric Utilities Corporation’s and UGI Utilities’ respective component of the total charge is posted on the PJM Internet website.
1/
Monday – Friday except the following holidays:  New Years Day, Memorial Day, Independence Day, Labor Day, Thanksgiving Day, and Christmas Day.
2/
Saturday and Sunday and the following holidays:  New Years Day, Memorial Day, Independence Day, Labor Day, Thanksgiving Day, and Christmas Day.
3/
The charge for Points of Delivery at the Border of PJM shall not apply to any Reserved Capacity with a Point of Delivery of the Midcontinent Independent 
Transmission System Operator, Inc.
4/
Each month, revenue credits will be applied to the gross charge in accordance with section 8 below to determine the actual charge to the Transmission Customer. 
5/
The charges for the ComEd zone are posted on PJM’s website.  In addition to other rates set forth in this schedule, customers within the ComEd zone shall be 
charged for recovery of RTO start-up costs at the following rates, each computed to four decimal places:
Annual Rate - $/kW/year = $1,523,039, divided by the 1 CP demand for the ComEd zone for the prior calendar year;
Monthly Rate - $/kW/month. = Annual Rate divided by 12;
Weekly Rate - $/kW/week = Annual Rate divided by 52;
Daily Rate - $/kW/day = Weekly Rate divided by 5.
In order to ensure that the charge does not result in either an over-recovery or under-recovery of ComEd’s start-up costs, PJM will institute an annual true-up 
mechanism in the month of May of each of the years 2008-2014.  In May of each of those years, PJM will compare the amount collected under this charge for the 
previous 12 months with the target annual amount of $1,523,039 and calculate any credits or surcharges that would be needed to ensure that $1,523,039 is collected 
for each year.  Any credit or surcharge will be assessed in the June bills for years 2008-2014, consistent with the above methodology.
6/
The rates for firm point-to-point transmission service in the AEP Zone will be charged at the yearly, monthly, weekly or daily rate equivalent to the rate effective in 
such period under Attachments H-14 and H-20. In addition to other rates set forth in this schedule, customers within the AEP East Zone shall be charged for 
recovery of RTO start-up costs at the following rates, each computed to four decimal places:
Annual Rate - $/kW/year = $2,362,185, plus any applicable true-up adjustment, divided by the 1 CP demand for the AEP East Zone for the prior calendar year;
Monthly Rate - $/kW/month. = Annual Rate divided by 12;
Weekly Rate - $/kW/week = Annual Rate divided by 52;
Daily Rate - $/kW/day = Weekly Rate divided by 5.
Page 79

PDF page 128

For the period November 1, 2005 through March 31, 2006, the rate shall be $8.94/MW-month; for the period April 1 through December 31, 2006, the rate shall be 
$8.60/MW-month, thereafter, the rate will be subject to the following true-up:
In order to ensure that the charge does not result in either over-recovery or under-recovery of AEP’s start-up costs, PJM will institute an annual true-up mechanism 
and implement revised charges as of January 1st of each of the years 2007-2019.  In January of each of those years, PJM will compare the amount collected under 
this charge for the previous year or part thereof with the target annual amount of $2,362,185 and calculate the rates that would be needed, given the expected billing 
demands, to collect $2,362,185, adjusted for any prior year over-collection or under-collection.  In the final year that the rate is collected, PJM will calculate the rate 
to collect five-twelfths of the annual amount ($984,244), plus or minus any prior year true up amount, by May 31 of that year, and shall charge such rate until that 
amount is collected, whether that date be before or after May 31, 2020.   
7/
The service period charges rounded to four decimal places for the Dominion Zone are as follows:
Yearly Charge - $/kW/year = the formula rate for Network Integration Transmission Service as described in Attachment H-16 and Attachment H-16A 
divided by 1000 kW/MW
Monthly Charge - $/kW/month. = Yearly Charge divided by 12;
Weekly Charge - $/kW/week = Yearly Charge divided by 52;
Daily On-Peak Charge - $/kW/day = Weekly Charge divided by 5;
Daily Off-Peak Charge - $/kW/day = Weekly Charge divided by 7.
On a monthly basis, revenue credits shall be calculated based on the sum of VEPCO’s share of revenues collected during the month from Schedule 7 and Network 
Integration Transmission Service to Non-Zone Network Load under Attachment H-A.  The sum of these revenue credits will appear as an adjustment to the to the 
gross monthly service period charges produced by the above formula.
2)
The total demand charge in any week, pursuant to a reservation for Daily On-Peak Delivery, or Daily Off-Peak Delivery shall not exceed the Weekly Delivery rate 
specified in section (1) above for weekly service times the highest amount in kilowatts of Reserved Capacity and any additional transmission service, if any, in any day during such 
week.
Page 80

PDF page 129

3)
Discounts:  Three principal requirements apply to discounts for transmission service as follows:  (1) any offer of a discount made by the Transmission Provider must be 
announced to all Eligible Customers solely by posting on the OASIS, (2) any customer-initiated requests for discounts (including requests for use by one’s wholesale merchant or 
an Affiliate’s use) must occur solely by posting on the OASIS, and (3) once a discount is negotiated, details must be immediately posted on the OASIS.  For any discount agreed 
upon for service on a path, from point(s) of receipt to point(s) of delivery, the Transmission Provider must offer the same discounted transmission service rate for the same time 
period to all Eligible Customers on all unconstrained transmission paths that go to the same point(s) of delivery on the Transmission System.
4)
Congestion, Losses and Capacity Export:  In addition to any payment under this Schedule, the Transmission Customer shall pay Redispatch Costs as specified in Section 
27 of the Tariff.  The Transmission Customer shall be responsible for losses as specified in the Tariff.  Any Transmission Customer that is a Capacity Export Transmission 
Customer, shall pay any applicable charges, and receive any applicable credits, for such a customer pursuant to Attachment DD.
5)
Other Supporting Facilities and Taxes:  In addition to the rates set forth in section (1) of this schedule, the Transmission Customer shall pay charges determined on a 
case-by-case basis for facilities necessary to provide Transmission Service at voltages lower than those shown in Attachment H for the applicable Zone(s) and any amounts 
necessary to reimburse PJMSettlement for any amounts payable as sales, excise, “Btu,” carbon, value-added or similar taxes (other than taxes based upon or measured by net 
income) with respect to the amounts payable pursuant to the Tariff.
6)
[Reserved]
7)
Transmission Enhancement Charges. Except for Points of Delivery at the Border of PJM, which are subject to the Border Yearly Charge determined under section 11, in 
addition to the rates set forth in section (1) of this Schedule and any other applicable charges, the Transmission Customer shall also pay any Transmission Enhancement Charges 
for which it is designated as a Responsible Customer under Schedule 12 appended to the Tariff.
8)
Determination of monthly charges for ComEd Zone: On a monthly basis, revenue credits shall be calculated based on the sum of ComEd’s share of revenues collected 
during the month from: (i) the PJM Border Rate under Schedule 7; (ii) Network Integration Transmission Service to Non-Zone Network Load under Attachment H-A; (iii) Seams 
Elimination Charge/Cost Adjustment/Assignment (“SECA”) revenues allocable to ComEd under the Tariff; and (iv) any Point-To-Point Transmission Service where the Point of 
Receipt and the Point of Delivery are both internal to the ComEd Zone. On this basis, the sum of these revenues will appear as a reduction to the gross monthly rate stated above 
on a Transmission Customer’s bill in that month for service under this schedule.
9)
Determination of monthly charges for AEP Zone: On a monthly basis, revenue credits shall be calculated based on the sum of AEP’s share of revenues collected during 
the month from: (i) the PJM Border Rate under Schedule 7; (ii) Network Integration Transmission Service to Non-Zone Network Load under Attachment H-A; and (iii) Firm 
Point-To-Point Transmission Service where the Point of Delivery is internal to the AEP Zone. The sum of these revenue credits will appear as an adjustment (reduction) to the 
gross monthly rate stated above on a Transmission Customer’s bill in that month for service under this schedule.
Page 81

PDF page 130

10)
Resales:  The rates and rules governing charges and discounts stated above shall not   apply to resales of transmission service, compensation for which shall be governed by 
section 23.1 of the Tariff.
11)
Determining the Border Yearly Charge
(A) Formula for Determining the Border Yearly Charge
(i)  Beginning with the calendar year 2020, the Border Yearly Charge shall be based on the following formula:
BYC = SHRR/SZPL
Where:
BYC is the Border Yearly Charge stated in dollars per kW of Reserved Capacity; 
SHRR is the sum of the Revenue Requirements for each Transmission Owner used to determine charges for Network Integration Transmission Service either (a) 
stated in Attachment H for a Transmission Owner or (b) determined pursuant to a formula rate set forth in Attachment H, both as adjusted in accordance with this 
section (11)(A). 
SZPL is the sum of each Zone’s annual peak load (in kW) plus the peak day firm reservations for Point-to-Point service at the Border of PJM (in kW) subject to the 
charges set forth in section (1) herein (prior to any applicable discount) from the most recently completed 12-month period ending October 31.
(ii) Where the Revenue Requirement of a Transmission Owner is determined pursuant to a formula rate: 
(a) the Revenue Requirement shall be increased by the amount of any revenue included in the Transmission Owner’s formula rate as credits in 
determining the Revenue Requirement for Network Integration Transmission Service from: (i) Transmission Enhancement Charges; (ii) Firm Point-to-Point 
Transmission Service charges under Schedule 7; (iii) Network Integration Transmission Service to Non-Zone Network Load under Attachment H-A; (iv) 
Interconnection Reliability Reinforcement Charges;  or (v) Generator Reliability Reinforcement Recovery Fees that are included in the Transmission Owner’s 
formula rate as revenue credits in determining the Revenue Requirement for Network Integration Transmission Service, if such credits are identified in the 
Transmission Owner’s formula rate annual update; and
Page 82

PDF page 131

(b)  (I) the Revenue Requirement shall be reduced by the amount of any credit applied directly to Network Customers to offset the cost of Network 
Integration Transmission Service, including credits to Network Customers resulting from: (i) a Network Upgrade Funding Agreement, Tariff, Attachment O-2; (ii) a 
State Agreement Public Policy Project subject to Tariff, Schedule 12, section (b)(xii)(B);  (iii) agreements for transmission service entered into prior to a 
Transmission Owner signing the Consolidated Transmission Owners Agreement or any of its predecessor agreements or (iv) an entity executing an agreement by 
which such entity is obligated to pay for some, or all, of the Revenue Requirement of Transmission Facilities for which Network Customers would otherwise be 
responsible. (II) The Revenue Requirement for inclusion in the SHRR shall not be reduced by the amount of any credits for (i) Transmission Enhancement Charges; 
(ii) Firm Point-to-Point Transmission Service charges under this Schedule 7; (iii) Network Integration Transmission Service to Non-Zone Network Load under 
Tariff, Attachment H-A; (iv) Interconnection Reliability Reinforcement Charges;  or (v) Generator Reliability Reinforcement Recovery Fees.
(B) The Transmission Provider shall update the Border Yearly Charge annually based on the Revenue Requirements for each Transmission Owner used to 
determine charges for Network Integration Transmission Service in effect on January 1, provided that such Revenue Requirements were approved by FERC, stated in a 
formula rate update informational filing with FERC, or posted on the Transmission Provider’s website no later than the preceding October 31.  The Border Yearly Charge 
so updated shall become effective as of January 1 and remain in effect for the remainder of the calendar year.  Except as provided in subsection (D) of this section (11), any 
change to the data used to determine the Border Yearly Charge following October 31, including any change in the number or identity of Transmission Owners filing 
Revenue Requirements for Network Integration Transmission Service under Attachment H, shall not be reflected in Border Yearly Charge until the next annual update.
(C) Not later than the first Business Day of December each year, the Transmission Provider shall post on the Transmission Provider’s website a “BYC Workbook” 
that shall include (1) all of the inputs and calculations used to determine the Border Yearly Charge, (2) references to the sources of the inputs used to determine the Border 
Yearly Charge from each Transmission Owner’s stated or formula rate filing or posting, (3) a variance report detailing all changes to the calculations, inputs, or procedures 
used to determine the proposed Border Yearly Charge as compared to the calculations, inputs or procedures used to determine the Border Yearly Charge then in effect, and 
(4) contact information for the submission of inquiries or comments regarding the posted BYC Workbook.  All inputs used to determine the SHRR must be taken either 
from a stated Revenue Requirement for Network Integration Transmission Service specified in Attachment H or from an identified entry in a Transmission Owner’s 
formula rate update either filed with the FERC or posted on the Transmission Provider’s website for the rate for Network Integration Transmission Service that will be in 
effect on January 1.  
(D)  Procedure for Review of and Challenge to the Border Yearly Charge Determination.
(i)  Review of the Border Yearly Charge Determination.
Page 83

PDF page 132

(a)  Within sixty (60) days of the posting of the BYC Workbook, Interested Parties, including entities with existing, requested or planned 
transmission service reservations for service at the Border of PJM (“Border Rate Transmission Customers”), state utility regulatory commissions, consumer advocacy 
agencies, state attorneys general, and any entity having standing under Section 206 of the Federal Power Act (“Interested Party”), may submit reasonable information 
requests to the Transmission Provider regarding its selection and use of inputs and the calculations performed in calculating the Border Yearly Charge, including the 
creation of the BYC Workbook, with respect to any adjustments made by the Transmission Provider, including adjustments made based on information provided by a 
Transmission Owner to the Transmission Provider:  (1) to a Transmission Owner’s Revenue Requirement for Network Integration Transmission Service prior to its 
inclusion as an input into the calculation of the SHRR for the Border Yearly Charge; (2) to the data used in determining SZPL; (3) to the Revenue Requirement of a 
Transmission Owner in determining the Border Yearly Charge made in accordance with Section (11)(A)(ii); and (4) in response to any FERC orders approving or requiring 
changes to, or refunds associated with, a Transmission Owner’s formula rate or resulting annual Revenue Requirement.
(b)  The Transmission Provider shall respond to such reasonable information requests as soon as practicable, but no later than within forty-five (45) 
days of the receipt of the information request, unless it determines that additional time is required to respond.  The Transmission Provider shall post any information 
requests received and its responses thereto on the Transmission Provider’s website, provided that any responsive information that has been designated by a Transmission 
Owner as confidential pursuant to the provisions of the Operating Agreement or Consolidated Transmission Owners Agreement shall not be posted and shall be handled 
solely in accordance with such provisions.  An Interested Party may request a meeting with the Transmission Provider and any interested Transmission Owner to discuss 
any response to an information request or any dispute regarding the calculation of the Border Yearly Charge annual update. The Transmission Provider and any interested 
Transmission Owner shall exercise good faith in responding to an Interested Party’s meeting request and shall not unreasonably deny or delay such meeting in a manner 
that prejudices an Interested Party’s opportunity to timely review the Border Yearly Charge annual update.
(c)  At any time after posting of the BYC Workbook, but before a challenge pursuant to section (11)(D)(ii) (“Challenge”) is filed, at the request of an 
Interested Party, the Transmission Provider will be required to meet with the Interested Party within ten (10) Business Days of such request in an attempt to resolve any 
dispute regarding the calculation of the Border Yearly Charge raised by the Interested Party in its meeting request. If the dispute relates to information from one or more 
Transmission Owners’ Tariff, Attachment H stated or formula rate or Zonal peak load determination, the relevant Transmission Owner(s) will be notified by the 
Transmission Provider of the dispute and will be permitted to attend the meeting.
(d)  If it is determined that the Border Yearly Charge is based on an incorrect input or calculation or FERC directs that a Transmission Owner’s
Revenue Requirement, upon which the Border Yearly Charge is based, be changed and implemented as a change to the Transmission Owner’s rate for Network Integration 
Transmission Service at a time other than provided for in the Transmission Owner’s formula rate protocols (“Changed Revenue Requirement”), the Transmission Provider 
shall change the   Border Yearly Charge as necessary to account for such Changed Revenue Requirement and post on the Transmission Provider’s website a revised BYC 
Workbook documenting the changes to the Border Yearly Charge to incorporate the correction or change. The correction to the Border Yearly Charge shall take effect no 
Page 84

PDF page 133

later than the first day of the month that begins 30 days after a correction is posted by the Transmission Provider or, if the correction or Changed Revenue Requirement 
results from a FERC order, on a schedule consistent with that order. Subject to the notice of correction described above, to the extent permitted by Tariff, Part I, section 
10.4, PJM Settlement, on behalf of itself or as agent for the Transmission Provider, shall adjust the charges to Border Rate Transmission Customers with respect to any 
month prior to the effective date of the Changed Revenue Requirement being reflected in the Border Yearly Charge that is affected by the correction or Changed Revenue 
Requirement and refund or credit any amount paid in excess of the corrected Border Yearly Charge. Any correction under this subsection (D) shall be limited to any 
Changed Revenue Requirement and the Transmission Provider’s selection and use of Border Yearly Charge inputs and the calculations necessary to determine the Border 
Yearly Charge. This section does not apply to a FERC order that changes a Transmission Owner’s Revenue Requirement that is implemented through a true-up mechanism.
(e) If FERC issues an order directing or approving refunds associated with a Transmission Owner’s Revenue Requirement that previously was, or 
currently is, incorporated into the SHRR to be paid to Network Integration Transmission Service customers, Border Rate Transmission Customers shall also receive a 
refund, to the extent that the changes in a Transmission Owner’s Revenue Requirement upon which such refund is based affects the calculation of the Border Yearly 
Charge.
(f)  Nothing in section (11) shall authorize an inquiry into the data or information filed or posted by a Transmission Owner as part of its transmission 
rate protocols pursuant to Tariff, Attachment H, or shall affect the rights that any Border Rate Transmission Customer may have under said protocols.
(ii)  Challenge to the Border Yearly Charge Determination.
(a)  An Interested Party may file with FERC a Challenge to the annual update of the Border Yearly Charge within  ninety (90) days of the posting of 
the BYC Workbook or thirty (30) days of receiving a response to any information request it submitted under subsection (11)(D)(i)(a), whichever is later.  Any such 
Challenge shall be served on Transmission Provider and each Transmission Owner with Revenue Requirements included in the BYC Workbook.
(b)  A Challenge must specify and include adequate supporting documentation, detailing how the Transmission Provider’s selection of inputs to or 
calculation of the Border Yearly Charge fails to comply with the provisions of this Schedule 7, section (11), identifying any input data or other BYC Workbook entry that is 
alleged to be missing or inaccurate or the Border Yearly Charge calculations alleged to be performed incorrectly.
(c)  A Challenge must be limited to the Transmission Provider’s selection and use of Border Yearly Charge inputs and the calculations necessary to 
determine the Border Yearly Charge and may not seek to modify Tariff, Schedules 7 and 8 or Attachment H-A or question the data or information filed or posted by a 
Transmission Owner pursuant to Tariff, Attachment H. 
Page 85

PDF page 134

(d)  The Transmission Provider and each Transmission Owner with Revenue Requirements included in the BYC Workbook shall have thirty (30) 
days to answer a Challenge.
(e)  In any proceeding before the FERC in response to a Challenge, the Transmission Provider shall bear the burden, consistent with Section 205 of 
the FPA, of demonstrating that it has correctly applied the terms of this Schedule 7, section (11).
(E) When the Transmission Provider posts on its website a Border Yearly Charge annual update under subsection (C) or correction under subsection (D) of this 
section (11), it shall also make an informational filing with the FERC that includes such posting.
(F) A Transmission Customer taking Point-to-Point Transmission Service at the Border of PJM under this Schedule 7, including any discounted service pursuant to 
Section (3), is relieved from, and shall not be separately allocated or assigned Transmission Enhancement Charges under Schedule 12 §(c)(5) on the basis of its reservation 
of Firm Point-to-Point Transmission Service at the Border of PJM.  Payment of the charges set forth in this Schedule does not relieve the responsibility of a Transmission 
Customer or Merchant Transmission Facility to pay Transmission Enhancement Charges assigned to such Merchant Transmission Facility, other than pursuant to Tariff, 
Schedule 12, §(c)(5), nor does it determine other cost obligations of Transmission Customers or Merchant Transmission Facilities that may be imposed under other 
provisions of the Tariff.  
(G)  Point-to-Point Transmission Service at the Border of PJM includes service to a Point of Delivery at a Merchant Transmission Facility that provides service to a 
neighboring transmission system.
(H)  Customers taking Point-to-Point Transmission Service at the Border of PJM with a Point of Delivery at a Merchant Transmission Facility and not receiving a 
discount from the Border Yearly Charge pursuant to this Schedule 7, section (3) under the settlement entered into in FERC Docket No. ER19-2105, shall receive a credit 
determined in accordance with the following formula:
MTFC = BYC*MTFTEC/SHRR
Where:
MTFC is the credit to the Border Yearly Charge per kW of reserved capacity; 
BYC is the Border Yearly Charge;
Page 86

PDF page 135

MTFTEC is the total annual Transmission Enhancement Charges under Tariff, Schedule 12 applicable to the Merchant Transmission Facility to which the customer 
is taking Point-to-Point Transmission Service during the current calendar year; and 
SHRR is the amount determined pursuant to subsection (A) of this section (11).
The MTFC shall be credited on a monthly basis only for those months during which the customer takes Firm Point-to-Point Transmission Service to the Merchant 
Transmission Facility.
Page 87

PDF page 136

SCHEDULE 12
Transmission Enhancement Charges and 
Interconnection Reliability Reinforcement Cost Recovery
(a)
Establishment of Transmission Enhancement Charges.  
(i)
Establishment of Transmission Enhancement Charges by Transmission 
Owners and Entities That Will Become Transmission Owners.  One or more of the 
Transmission Owners may be designated to construct and own and/or finance Required 
Transmission Enhancements by (1) the Regional Transmission Expansion Plan periodically 
developed pursuant to Operating Agreement, Schedule 6 or (2) any joint planning or 
coordination agreement between PJM and another region or transmission planning authority set 
forth in Tariff, Schedule 12-Appendix B (“Appendix B Agreement”) (collectively, for purposes 
of this Schedule 12 only, “Regional Transmission Expansion Plan”).  Operating Agreement, 
Schedule 6, section 1.7 recognizes that Transmission Owners, subject to obtaining any necessary 
regulatory approvals, may seek to recover the costs of Required Transmission Enhancements and 
obligates PJMSettlement to collect on behalf of Transmission Owner(s) any charges established 
by Transmission Owners to recover the costs of Required Transmission Enhancements.  If a 
Transmission Owner is designated by the Regional Transmission Expansion Plan to construct 
and own and/or finance a Required Transmission Enhancement, such Transmission Owner may 
choose any of the following cost recovery mechanisms, subject to the crediting procedures set 
forth in section (e) below: 
(1)
Decline to seek to recover the costs of Required Transmission Enhancements 
from customers until such time as it makes a filing pursuant to Section 205 of the Federal 
Power Act to revise its Network Integration Transmission Service rates;
(2) 
Make a filing pursuant Section 205 of the Federal Power Act and the FERC’s 
rules and regulations to establish the revenue requirement with respect to a Required 
Transmission Enhancement, without filing to revise its rates for Network Integration 
Transmission Service generally; or
(3) 
Establish the revenue requirement with respect to a Required Transmission 
Enhancement through the operation of a formula rate in effect applicable to its rates for 
Network Integration Transmission Service.
A charge established to recover the revenue requirement with respect to a Required Transmission 
Enhancement is hereafter referred to as a “Transmission Enhancement Charge.”  Transmission 
Enhancement Charges of one or more Transmission Owners for Required Transmission 
Enhancements shall be established in accordance with this Schedule 12.   
(ii)
Establishment of Transmission Enhancement Charges With Respect to 
Required Transmission Enhancements Constructed by Entities in Another Region. The 
revenue requirement with respect to a Required Transmission Enhancement constructed pursuant 
to an Appendix B Agreement in another region by an entity designated by such other region shall 
be governed by the tariffs or agreements in effect in such region. Transmission Enhancement 
Page 88

PDF page 137

Charges to recover the costs of such Required Transmission Enhancement for which PJM is 
responsible shall be determined in accordance with this Schedule 12.  Other than with respect to 
a Required Transmission Enhancement constructed pursuant to an Appendix B Agreement, no 
PJM Network or Transmission Customer will bear cost responsibility for any required 
transmission upgrades in another region as a consequence of a Required Transmission 
Enhancement included in the Regional Transmission Expansion Plan.  
(iii)
Transmission Facilities Not Eligible for Cost Responsibility Assignment.  Any 
alternating current (“A.C.”) facilities or direct current (“D.C.”) facilities that are Attachment 
Facilities, Local Upgrades, Merchant Network Upgrades, Merchant Transmission Facilities, 
Network Upgrades, Supplemental Projects, or any other Transmission Facilities that operate or 
are planned to be operated in a manner that requires customers to subscribe to transmission 
service over such facilities or to a portion of the electric capability of such facilities shall not be 
eligible for cost responsibility assignment pursuant to this Schedule 12.  
(iv)
Entities Not Yet Eligible to Become Transmission Owners.  For purposes of 
this Schedule 12 only, the term, “Transmission Owner,” shall include any entity that undertakes 
to construct and own and/or finance a Required Transmission Enhancement pursuant to a 
designation in the Regional Transmission Expansion Plan to construct and own and/or finance 
such Required Transmission Enhancement, even if such entity is not yet eligible to become a 
party to the Consolidated Transmission Owners Agreement.  Nothing in the PJM Tariff nor the 
Consolidated Transmission Owners Agreement shall prevent an entity that undertakes to 
construct and own and/or finance a Required Transmission Enhancement pursuant to a 
designation in the Regional Transmission Expansion Plan to construct and own and/or finance 
such Required Transmission Enhancement from recovering the costs of such Required 
Transmission Enhancement through this Schedule 12.
(v)
Effective Date.  The assignment of cost responsibility or classification of 
Required Transmission Enhancements either (1) made by the Transmission Provider prior to 
February 1, 2013, or (2) applicable to Required Transmission Enhancements approved by the 
PJM Board pursuant to Operating Agreement, section 1.6 prior to February 1, 2013 are set forth 
in Tariff, Schedule 12-Appendix.  Except as specifically set forth herein, nothing in this 
Schedule 12 shall change the assignment of cost responsibility or classification of Required 
Transmission Enhancements included in Tariff, Schedule 12-Appendix.  The assignment of cost 
responsibility or classification of all other Required Transmission Enhancements shall be set 
forth in Tariff, Schedule 12-Appendix A. 
(b)
Designation of Customers Subject to Transmission Enhancement Charges.  
(i)
Regional Facilities and Necessary Lower Voltage Facilities.  Transmission 
Provider shall assign cost responsibility on a region-wide basis for Required Transmission 
Enhancements included in the Regional Transmission Expansion Plan that (1) (a) are A.C. 
facilities that operate at or above 500 kV; (b) constitute a single Required Transmission 
Enhancement comprising two A.C. circuits operating at or above 345 kV and below 500 kV, 
where both circuits originate from a single substation or switching station at one end and 
Page 89

PDF page 138

terminate at a single substation or switching station at the other end, regardless of whether or not 
the two circuits are routed in the same right-of-way (“Double-circuit 345 kV Required 
Transmission Enhancement”); (c) are A.C. or D.C. shunt reactive resources (such as capacitors, 
static var compensators, static synchronous condenser (STATCON), synchronous condensers, 
inductors, other shunt devices, or their equivalent) connected to a Transmission Facility 
described in clause (a) or (b) of this subsection, or (d) are D.C. facilities meeting the criteria set 
forth in subsection (b)(i)(D) (collectively, “Regional Facilities”), or (2) new A.C. Transmission 
Facilities or expansions or enhancements to existing Transmission Facilities that operate below 
500 kV (or 345 kV in the case of a Regional Facility described in clause (1)(b) of this 
subsection) or new D.C. Transmission Facilities that do not meet the criteria of subsection 
(b)(i)(D) that must be constructed or strengthened to support new Regional Facilities, based on 
the planning criteria used by the Transmission Provider in developing the applicable Regional 
Transmission Expansion Plan (“Necessary Lower Voltage Facilities”) as follows: 
(A)
Cost responsibility for Regional Facilities and Necessary Lower Voltage 
Facilities shall be allocated among Responsible Customers as defined in this Schedule 12 as 
follows:
(1)
Fifty percent (50%) shall be assigned annually on a load-ratio 
share basis as follows:
(a)
With respect to each Zone, using, consistent with Tariff, 
Part III, section 34.1, the applicable zonal loads at the time of such Zone’s annual peak load from 
the 12-month period ending October 31 preceding the calendar year for which the annual cost 
responsibility allocation is determined; and
(b)
With respect to Merchant Transmission Facilities, (1) for 
the calendar year following the year in which it initiates operation, the actually awarded Firm 
Transmission Withdrawal Rights associated with its existing Merchant Transmission Facility; 
and (2) for all subsequent calendar years, the annual peak load of the Merchant Transmission 
Facility (not to exceed its actual Firm Transmission Withdrawal Rights) from the 12-month 
period ending October 31 of the calendar year preceding the calendar year for which the annual 
cost responsibility allocation is determined.
(2)
Fifty percent (50%) shall be assigned as follows:
(a)
In the case of a Required Transmission Enhancement 
included in the Regional Transmission Expansion Plan to address one or more reliability 
violations or to address operational adequacy and performance issues (collectively, “Reliability 
Project”), in accordance with the distribution factor (“DFAX”) analysis described in subsection 
(b)(iii) or the analysis applicable to Regional Facilities that address stability issues described in 
subsection (b)(xviii) of this Schedule 12 as applicable; and
(b)
In the case of a Required Transmission Enhancement 
included in the Regional Transmission Expansion Plan to relieve one or more economic 
constraints as described in Operating Agreement, Schedule 6, section 1.5.7(b)(iii) (“Economic 
Page 90

PDF page 139

Project”), in accordance with the methodology described in subsection (b)(v) of this Schedule 
12.
(B)
(1) Except for transformers that are an integral component of a Regional 
Facility, transformers connected to Lower Voltage Facilities, as defined in section (b)(ii) of this 
Schedule 12, shall not be considered Regional Facilities or Necessary Lower Voltage Facilities; 
and (2) Transmission Facilities that are not Regional Facilities and deliver energy from a 
Regional Facility to load shall not be considered Necessary Lower Voltage Facilities.
(C)
With respect Required Transmission Enhancements that qualify as 
Regional Facilities under subsection (b)(i)(1)(b) or subsection (b)(i)(D)(2) of this Schedule 12:
(1)
where the Required Transmission Enhancement includes both new 
Transmission Facilities and pre-existing Transmission Facilities, cost responsibility under this 
section (b)(i) shall apply only to the cost of the new Transmission Facilities plus the original cost 
less accumulated depreciation of pre-existing Transmission Facilities that are included in Tariff, 
Schedule 12-Appendix or Tariff, Schedule 12-Appendix A;
(2)
cost responsibility shall be assigned under this section (b)(i) only 
after the Required Transmission Enhancement goes into service as a Double-circuit 345 kV 
Required Transmission Enhancement or a Double-circuit D.C. Required Transmission 
Enhancement; and 
(3)
cost responsibility shall be assigned under this section (b)(i) for 
any CWIP permitted to be recovered before the Required Transmission Enhancement goes into 
service only after such Transmission Facilities are approved in a Regional Transmission 
Expansion Plan as a Double-circuit 345 kV Required Transmission Enhancement or a Double-
circuit D.C. Required Transmission Enhancement.
(D)
A Required Transmission Enhancement included in the Regional 
Transmission Expansion Plan that is a D.C. facility, consisting of D.C. lines (i.e., wires or 
cables) and A.C./D.C. converters, shall be a Regional Facility only if: 
(1) 
such D.C. facility comprises two poles and operates at a voltage of 
±433 kV D.C. or above; or
(2)
such D.C. Facility constitutes a single Required Transmission 
Enhancement comprising two D.C. circuits where (i) both circuits originate from a single 
substation or switching station at one end and terminate at a single substation or switching 
station at the other end, regardless of whether or not both circuits are routed in the same right-of-
way, and (ii) each such circuit consists of two poles and operates at a voltage of ±298 kV D.C or 
above (“Double-circuit D.C. Required Transmission Enhancement”).
(ii)
Lower Voltage Facilities.  Transmission Provider shall assign cost responsibility 
for Required Transmission Enhancements that (a) are not Regional Facilities; and (b) are not 
“Necessary Lower Voltage Facilities” as defined in section(b)(i) of this Schedule 12 (collectively 
“Lower Voltage Facilities”), as follows:
Page 91

PDF page 140

(A)
If the Lower Voltage Facility is a Reliability Project,  Transmission 
Provider shall use the DFAX analysis described in subsection (b)(iii) or the analysis applicable to 
Regional Facilities that address stability issues described in subsection (b)(xviii) of this Schedule 
12 as applicable; and
(B)
If the Lower Voltage Facility is an Economic Project, Transmission 
Provider shall use the methodology described in subsection (b)(v) of this Schedule 12.
(iii)
DFAX Analysis for Reliability Projects.  
(A)  For purposes of the assignment of cost responsibility for Reliability Projects 
under subsection (b)(i)(A)(2)(a) and subsection (b)(ii)(A) of this Schedule 12, the Transmission 
Provider, based on a computer model of the electric network and using power flow modeling 
software, shall calculate distribution factors, represented as decimal values or percentages, which 
express the portions of a transfer of energy from a defined source to a defined sink that will flow 
across a particular transmission facility or group of transmission facilities.  These distribution 
factors represent a measure of the use by the load of each Zone or Merchant Transmission 
Facility (collectively, “Responsible Zone”) of the Required Transmission Enhancement, as 
determined by a power flow analysis.  In general, a distribution factor can be represented as:
Distribution Factor = (After-shift power flow – pre-shift power flow) / Total amount of power 
shifted
Total amount of power shifted = Modeled incremental megawatt transfer to a given Load 
Deliverability Area or Merchant Transmission Facility
Pre-shift power flow = Megawatt flow over the Required Transmission Enhancement  
before the incremental megawatt transfer
After-shift power flow = Megawatt flow over the Required Transmission Enhancement 
after the incremental megawatt transfer
When calculating such distribution factors:
(1)
All distribution factors are calculated with respect to the Required 
Transmission Enhancement subject to cost allocation under subsection (b)(i)(A)(2)(a) and 
subsection (b)(ii)(A) of this Schedule 12.
(2)
The calculation of distribution factors shall be determined using 
linear matrix algebra, such that distribution factors represent the ratio of (i) a change in megawatt 
flow on a Required Transmission Enhancement to (ii) a change in megawatts transferred to 
aggregate load within a Zone or, in the case of a Merchant Transmission Facility, the point of 
withdrawal associated with Firm Transmission Withdrawal Rights over such Merchant 
Transmission Facility.
Page 92

PDF page 141

(3)
With respect to a Merchant Transmission Facility, zonal peak load 
shall mean (i) the existing Firm Transmission Withdrawal Rights of the Merchant Transmission 
Facility being evaluated, if the Merchant Transmission Facility is in service, or (ii) for a 
Merchant Transmission Facility that is not yet in service, the planned Firm Transmission 
Withdrawal Rights of the Merchant Transmission Facility being evaluated as identified in the 
Interconnection Service Agreement in effect for such Merchant Transmission Facility. 
(4)
In the DFAX analysis, when Transmission Provider models a 
transfer from generation to all load within an individual Zone, Transmission Provider shall 
model the transfer to the Zone as a whole (not on a bus-by-bus basis).  
(5)
In the DFAX analysis, Transmission Provider shall model 
generation both external and internal to individual Responsible Zones to reflect (a) the 
boundaries of Locational Deliverability Areas (“LDAs”), and (b) limitations with respect to the 
reliability objective for moving generation capacity across the transmission system.  
Transmission Provider shall adopt the Capacity Emergency Transfer Objective (“CETO”), 
associated with that LDA and calculated for the applicable planning year to be the transfer 
limitation into the LDA.  In modeling the system generation and load, Transmission Provider 
shall assume that the percentage of the zonal load in the LDA served by external (or internal) 
generation to the LDA shall equal the ratio of (i) the CETO associated within that LDA (or 
generation internal with the LDA) to (ii) the sum of (a) the internal generation within the LDA 
and (b) the CETO associated with that LDA.  For the generation dispatch used in calculating the 
distribution factor, Transmission Provider shall distribute these amounts of external/internal 
generation among all generation in the PJM Region external to/internal within the LDA, 
respectively, in proportion to their capacity.  For Responsible Zones that are located within 
LDAs that are also entirely contained in other larger LDAs, the modeling approach and 
distribution factor calculations shall be repeated for such Responsible Zones for each LDA.  The 
lowest distribution factor derived from these calculations shall be applied to the Responsible 
Zone in the calculation of the use of the Required Transmission Enhancement.  
(B) 
The DFAX analysis will be performed in accordance with the following 
steps:
(1)
Transmission Provider shall calculate a distribution factor and a 
direction of use for each Responsible Zone by modeling a transfer from all generation in the PJM 
Region to each Responsible Zone.  To establish the use by a Responsible Zone, in megawatts, of 
a Required Transmission Enhancement, the distribution factor of a Required Transmission 
Enhancement associated with the resulting transfer modeled by the Transmission Provider to 
each Responsible Zone shall be multiplied by the Responsible Zone’s peak load.
(2)
The Transmission Provider shall separately determine the relative 
use of the Required Transmission Enhancement by each Responsible Zone in each direction by 
dividing the megawatts of use by each Responsible Zone determined in section (iii)(B)(1) above 
Page 93

PDF page 142

by the total use of all Responsible Zones using the Required Transmission Enhancement in the 
same direction of use.
(3) 
Transmission Provider shall determine the direction of use 
percentage of the Required Transmission Enhancement in each direction using a production cost 
analysis to determine the total use, in megawatt-hours, of the Required Transmission 
Enhancement by all Zones and Merchant Transmission Facilities in each direction over the 
course of a year.  The Transmission Provider shall calculate the percentage use in each direction 
by dividing the megawatt-hours of use in each direction by total use in megawatt-hours in both 
directions of use.
(4)
The Transmission Provider shall multiply the relative use by each 
Responsible Zone of the Required Transmission Enhancement in each direction of use 
determined in section (iii)(B)(2) above, by the applicable direction of use percentage determined 
in section (iii)(B)(3) above. 
(5)
The products of the calculation performed in section (iii)(B)(4) 
above, shall determine the relative allocation to each Responsible Zone of cost responsibility for 
the Required Transmission Enhancement.
(C)
In the DFAX analysis, the Zones of Public Service Electric and Gas 
Company and Rockland Electric Company will be treated as one Zone unless and until Rockland 
Electric Company elects to be treated as a separate Zone in accordance with the terms of the 
Settlement Agreement And Offer Of Partial Settlement approved by FERC in Docket Nos. 
ER06-456-000, et al.
(D)
Transmission Provider shall round cost responsibility assignments 
determined using the DFAX analysis described in subsection (b)(iii) of this Schedule 12 to the 
nearest one-hundredth of one percent.
(E)
Transmission Provider shall not account for the ability to adjust use of 
phase angle regulators (“PARs”) in the DFAX analysis described in subsection (b)(iii) of this 
Schedule 12.  In the DFAX analysis, all PAR angles shall be fixed at their base case settings. 
(F)
In the DFAX analysis, if the Required Transmission Enhancement is a 
D.C. facility, the Transmission Provider shall determine cost responsibility assignment as 
follows:
(1)
The Required Transmission Enhancement shall be replaced in the 
model with a comparable proxy A.C. facility, the impedance of which shall be calculated based 
on the length of the D.C. facility that was removed from the model multiplied by an approximate 
per unit/mile impedance value for the proxy A.C. facility.
(2)
Where a D.C. facility is an integral part of a Required 
Transmission Enhancement that also includes A.C. facilities, the methodology described in 
Page 94

PDF page 143

subsection (b)(iii)(F)(1) above shall be used only for the D.C. facility segment of such Required 
Transmission Enhancement.
(3)
A D.C. facility used to control flow over portions of the 
Transmission System shall be modeled with a zero impedance and no control shall be applied.
(G)
If Transmission Provider determines in its reasonable engineering judgment 
that, as a result of applying the provisions in section (b)(iii) of this Schedule 12, the DFAX 
analysis cannot be performed or that the results of such DFAX analysis are objectively 
unreasonable, the Transmission Provider may use an appropriate substitute proxy for the 
Required Transmission Enhancement in conducting the DFAX analysis.  If a proxy is used that is 
not specified in this Schedule 12, Transmission Provider shall state in a written report (a) the 
reasons why it determined the DFAX analysis could not be performed or that the results of the 
DFAX analysis were objectively unreasonable; (b) why the substitute proxy produced 
objectively reasonable results; and (3) a recommendation as to what changes, if any, should be 
considered in conducting the DFAX analysis.
(H)
The Transmission Provider shall make a preliminary cost responsibility 
determination for each Required Transmission Enhancement subject to section (b)(iii) of this 
Schedule 12 at the time such Required Transmission Enhancement is included in the Regional 
Transmission Expansion Plan.  
(1) 
When CWIP in connection with a Required Transmission 
Enhancement subject to this section (b)(iii) of this Schedule 12 is entitled to be recovered, the 
preliminary determination of cost responsibility made at the time that the Required Transmission 
Enhancement was included in the Regional Transmission Expansion Plan shall be used to assign 
cost responsibility for such CWIP and such cost responsibility shall remain unchanged until the 
date the Required Transmission Enhancement goes into service.  Once a Required Transmission 
Enhancement has gone into service, the updated cost responsibility determination provided for in 
subsection (b)(iii)(H)(2) below shall apply.
(2)
Beginning with the calendar year in which a Required 
Transmission Enhancement is scheduled to enter service, and thereafter annually at the 
beginning of each calendar year, the Transmission Provider shall update the preliminary cost 
responsibility determination for each Required Transmission Enhancement using the values and 
inputs used in the base case of the most recent Regional Transmission Expansion Plan approved 
by the PJM Board prior to the date of the update.  All values and inputs used in the calculation of 
the distribution factor in a determination of cost responsibility shall be the same values and 
inputs as used in the base case of the most recent Regional Transmission Expansion Plan 
approved by the PJM Board prior to the determination of cost responsibility.  
(iv)
Spare Parts, Replacement Equipment And Circuit Breakers.  Transmission 
Provider shall assign cost responsibility for spare parts, replacement equipment, and circuit 
breakers and associated equipment, included in the Regional Transmission Expansion Plan as 
follows:
Page 95

PDF page 144

(A)
Spare parts that are part of the design specifications of a Required 
Transmission Enhancement at the time such Required Transmission Enhancement is first 
included in the Regional Transmission Expansion Plan shall be considered part of the Required 
Transmission Enhancement for the purpose of applying the cost threshold described in 
subsection (b)(vi) of this Schedule 12 and cost responsibility for such spare parts shall be 
assigned in the same manner as the Required Transmission Enhancement.  Cost responsibility for 
spare parts independently included the Regional Transmission Expansion Plan and not a part of 
the design specifications of a Required Transmission Enhancement as described above in this 
subsection shall be assigned to the Zone of the owner of the spare part, if the owner of the spare 
part is a Transmission Owner listed in Tariff, Attachment J.  If the owner of the spare part is not 
a Transmission Owner listed in Tariff, Attachment J, cost responsibility shall be assigned on a 
pro rata basis to the zones that bear cost responsibility for the owner’s Required Transmission 
Enhancements.
(B)
Replacement equipment that is part of the design specifications of a 
Required Transmission Enhancement at the time the Required Transmission Enhancement is first 
included in the Regional Transmission Expansion Plan shall be considered part of the Required 
Transmission Enhancement for the purpose of applying the cost threshold described in section 
(b)(vi) of this Schedule 12 and cost responsibility for such replacement equipment shall be 
assigned in the same manner as the Required Transmission Enhancement. Cost responsibility for 
Required Transmission Enhancement replacement equipment independently included in the 
Regional Transmission Expansion Plan and not a part of the design specifications of a Required 
Transmission Enhancement as described above in this subsection, shall be assigned to the same 
Zones and/or Merchant Transmission Facilities and in the same proportions as the then-existing 
assignments of cost responsibility for the facilities that the replacement equipment is replacing.
(C)
Circuit breakers and associated equipment that are part of the design 
specifications of a Required Transmission Enhancement at the time the Required Transmission 
Enhancement is first included in the Regional Transmission Expansion Plan shall be considered 
part of the Required Transmission Enhancement for the purpose of applying the cost threshold 
described in subsection (b)(vi) of this Schedule 12 and cost responsibility for such circuit 
breakers and associated equipment shall be assigned in the same manner as the Required 
Transmission Enhancement.  Cost responsibility for circuit breakers and associated equipment 
independently included in the Regional Transmission Expansion Plan and not a part of the design 
specifications of a transmission element of a  Required Transmission Enhancement as described 
above in this subsection, shall be assigned to the Zone of the owner of the circuit breaker and 
associated equipment if the owner of the circuit breaker is a Transmission Owner listed in Tariff, 
Attachment J.  If the owner of the circuit breaker is not a Transmission Owner listed in Tariff, 
Attachment J, cost responsibility shall be assigned on a pro rata basis to the zones that bear cost 
responsibility for the owner’s Required Transmission Enhancements. 
(v)
Economic Projects.  Transmission Provider shall assign (i) fifty percent (50%) of 
cost responsibility for Economic Projects that are Regional Facilities; and (ii) full cost 
responsibility for Economic Projects that are Lower Voltage Facilities; as follows:
Page 96

PDF page 145

(A)
Transmission Provider shall assign cost responsibility for Economic 
Projects that are accelerations of Reliability Projects as described in Operating Agreement, 
Schedule 6, section 1.5.7(b)(i) (“Acceleration Projects”) by performing and comparing (1) a 
DFAX analysis consistent with the methodology described in subsection (b)(iii) of this Schedule 
12, and (2) a methodology that is intended to act as a proxy for expected economic benefits from 
reduced Locational Marginal Prices (“LMP Benefit”) over the period that the reliability-based 
enhancement or expansion is to be accelerated (“LMP Benefits Methodology”).  The LMP 
Benefits Methodology shall determine cost responsibility assignment percentages to Zones and 
Merchant Transmission Facilities in the following manner.  The LMP Benefit to a Zone shall be 
deemed to be equal to the reduction in Locational Marginal Price payments made by Load 
Serving Entities as a result of the Acceleration Project assuming the customers purchase all 
energy needs from the PJM Interchange Energy Market, and LMP Benefits so calculated shall be 
converted into percentage cost responsibility assignments for the affected Zones.  The LMP 
Benefits Methodology shall not incorporate the financial effects of allocations of Auction 
Revenue Rights or Financial Transmission Rights.  The LMP Benefit to a Merchant 
Transmission Facility shall be deemed to be equal to the proportionate share of assigned cost 
responsibility using the DFAX analysis and the assignments of cost responsibility to other Zones 
in the LMP Benefits Methodology shall be proportionately adjusted, as necessary, to reflect this 
treatment of Merchant Transmission Facilities to ensure that the total allocation for any 
economic-based Required Transmission Enhancement equals one hundred percent.  If, after 
performing both analyses and comparing the percentage cost responsibility assignments for the 
affected Zones calculated pursuant to the DFAX analysis and the LMP Benefits Methodology, 
the results do not indicate at least a ten percentage point cost responsibility assignment 
differential between the two methods for any Zone, cost responsibility for the Acceleration 
Project shall be assigned using the DFAX analysis.  If, after performing both analyses and 
comparing the percentage cost responsibility assignments for the affected Zones calculated 
pursuant to the DFAX analysis and LMP Benefits Methodology, the results indicate at least a ten 
percentage point cost responsibility assignment differential between the DFAX analysis and the 
LMP Benefits Methodology for any Zone, cost responsibility for the Acceleration Project for the 
period of time the Reliability Project is accelerated (i.e. the period between the date the 
Reliability Project actually goes into service and the date the Reliability Project originally was 
scheduled to go in service in the PJM Board approved Regional Transmission Expansion Plan) 
shall be assigned using the LMP Benefits Methodology.  For all periods other than the period of 
time the Reliability Project is accelerated, cost responsibility for such an Acceleration Project 
shall be assigned in accordance with the provisions of this Schedule 12 governing the assignment 
of cost responsibility of Regional Facility Reliability Projects or Lower Voltage Facility 
Reliability Projects, as applicable.  
(B)
Transmission Provider shall assign cost responsibility for Economic 
Projects that are modifications to Reliability Projects as described in Operating Agreement, 
Schedule 6, section 1.5.7(b)(ii) in accordance with the provisions of this Schedule 12 governing 
the assignment of cost responsibility of Regional Facility Reliability Projects or Lower Voltage 
Facility Reliability Projects, as applicable.
(C)
Transmission Provider shall assign cost responsibility for Economic 
Projects that are new enhancements or expansions that could relieve one or more economic 
Page 97

PDF page 146

constraints as described in Operating Agreement, Schedule 6, section 1.5.7(b)(iii) to the Zones 
that show a decrease in the net present value of the Changes in Load Energy Payment.  The 
Change in Load Energy Payment for each year shall be determined using the methodology set 
forth in Operating Agreement, Schedule 6, section 1.5.7(d) for the period specified in that 
section.  Cost responsibility shall be assigned based on each Zone’s pro rata share of the sum of 
the net present values of the Changes in Load Energy Payment only of the Zones in which the 
net present value of the Changes in Load Energy Payment shows a decrease.
(vi)
Required Transmission Enhancements Costing Less Than $5 Million.  
Notwithstanding sections (b)(i), (b)(ii), (b)(iv) and (b)(v) of this Schedule 12, cost responsibility 
for a Required Transmission Enhancement for which the good faith estimate of the cost of the 
Required Transmission Enhancement (a) prepared in connection with the development of the 
Regional Transmission Expansion Plan and (b) provided to the PJM Board at the time the 
Required Transmission Enhancement is included for the first time in the Regional Transmission 
Expansion Plan, does not equal or exceed $5 million shall be assigned to the Zone where the 
Required Transmission Enhancement is to be located.  The determination of whether the 
estimated cost of a Required Transmission Enhancement does not equal or exceed $5 million 
shall be based solely on such good faith estimate of the cost of the Required Transmission 
Enhancement regardless of the actual costs incurred.  The estimated cost of a Required 
Transmission Enhancement shall include the aggregate estimated costs of all of the transmission 
elements approved by the PJM Board at the time such elements are included in the Regional 
Transmission Expansion Plan that collectively are intended (i) in the case of a Reliability Project, 
to resolve a specific reliability criteria violation, or (ii) in the case of an Economic Project, 
provide a specific LMP Benefit.  Where a Required Transmission Enhancement subject to this 
section (b)(vi) consists of a single transmission element or multiple transmission elements that 
will be located in more than one Zone, each Zone shall be assigned cost responsibility for the 
transmission elements or portions of the transmission elements located in such Zone.  Merchant 
Transmission Facilities shall not be assigned cost responsibility for a Required Transmission 
Enhancement subject to this section (b)(vi).
(vii)
Modifications of Required Transmission Enhancements.  Once a Required 
Transmission Enhancement is included in the Regional Transmission Expansion Plan, any 
modification to such Required Transmission Enhancement that subsequently is included in the 
Regional Transmission Expansion Plan as a separate Reliability or Economic Project shall be 
considered a separate and distinct Required Transmission Enhancement for purposes of cost 
responsibility assignment under this Schedule 12.  Except as provided in sections (b)(iv) and 
(b)(xiv) of this Schedule 12, any cost responsibility assignment that has been made for a 
previously approved Required Transmission Enhancement shall have no impact on the cost 
responsibility assignment of such modification.
(viii)
FERC Filing.  Within 30 days of the approval of each Regional Transmission 
Expansion Plan or an addition to such plan by the PJM Board pursuant to Operating Agreement, 
Schedule 6, section 1.6, the Transmission Provider shall designate in the Tariff, Schedule 12-
Appendix A and in a report filed with the FERC the Responsible Customers based on the cost 
responsibility assignments determined pursuant to this Schedule 12.  Those customers designated 
by the Transmission Provider as Responsible Customers shall have 30 days from the date the 
Page 98

PDF page 147

filing is made with the FERC to seek review of such designation. Such cost responsibility 
designations shall be the same as those made for the relevant Regional Facility, Necessary Lower 
Voltage Facility, or Lower Voltage Facility in the Regional Transmission Expansion Plan.
(ix)
Regions With Which PJM Has Entered Into an Agreement Listed in 
Schedule 12-Appendix B .  For purposes of this Schedule 12, where costs of a Required 
Transmission Enhancement are allocated to a region other than PJM pursuant to an agreement set 
forth in Tariff, Schedule 12-Appendix B, Responsible Customers for such costs shall be 
customers in such region. Cost responsibility with respect to the costs of a Required 
Transmission Enhancements  allocated to a region other than PJM shall be allocated within such 
region in accordance with the applicable tariff or agreement governing the allocation of such 
costs in such region.
(x)
Merchant Transmission Facilities.
(A)
For purposes of this Schedule 12, where the Transmission Provider has 
allocated all or a portion of a Required Transmission Enhancement to a Merchant Transmission 
Facility, the owner of the Merchant Transmission Facility shall be the Responsible Customer 
with respect to such Required Transmission Enhancement, and shall pay the Transmission 
Enhancement Charges associated with the Required Transmission Enhancement.
(B)
(1)
Transmission Provider shall defer collection of Transmission 
Enhancement Charges from a Merchant Transmission Facility until the Merchant Transmission 
Facility goes into commercial operation; provided, however, in the event the commercial 
operation of a Merchant Transmission Facility is delayed beyond the commercial operation 
milestone date(s) specified in the Interconnection Service Agreement associated with the 
Merchant Transmission Facility and the Transmission Provider or Transmission Owner 
constructing the Required Transmission Enhancement demonstrates that the Merchant 
Transmission Facility is responsible for such delay, Transmission Provider may begin collecting 
Transmission Enhancement Charges from the Merchant Transmission Facility prior to the 
Merchant Transmission Facility going into commercial operation.  Transmission Enhancement 
Charges allocated to a Merchant Transmission Facility for which collection is deferred in 
accordance with this section (b)(x)(B)(1) shall be recorded in appropriate Transmission Provider 
accounts for deferred charges and collected in accordance with section (b)(x)(B)(3) below.  
(2)
Transmission Provider shall base the collection of Transmission 
Enhancement Charges associated with Required Transmission Enhancements from a Merchant 
Transmission Facility on the actual Firm Transmission Withdrawal Rights that have been 
awarded to the Merchant Transmission Facility; provided, however, to the extent that a Merchant 
Transmission Facility has been awarded less than the amount of Firm Transmission Withdrawal 
Rights specified in the Interconnection Service Agreement associated with the Merchant
Transmission Facility, then Transmission Provider shall record the difference between the 
amount of Transmission Enhancement Charges collected based on the lesser amount of Firm 
Transmission Withdrawal Rights and the amount of Transmission Enhancement Charges based 
on the full amount of Firm Transmission Withdrawal Rights specified in the applicable 
Interconnection Service Agreement in appropriate accounts for deferred charges and, after the 
Page 99

PDF page 148

Merchant Transmission Facility has been awarded the full amount of Firm Transmission 
Withdrawal Rights specified in the Interconnection Service Agreement, collect such deferred 
amounts in accordance with section (b)(x)(B)(3) below.  Notwithstanding the foregoing, 
Transmission Provider may collect Transmission Enhancement Charges based on more than a 
Merchant Transmission Facility’s actually awarded Firm Transmission Withdrawal Rights (not 
to exceed the Firm Transmission Withdrawal Rights specified in the applicable Interconnection 
Service Agreement) if the Transmission Provider or Transmission Owner demonstrates that the 
Merchant Transmission Facility is responsible for receiving fewer Firm Transmission 
Withdrawal Rights than are specified in the applicable Interconnection Service Agreement.
(3)
Transmission Provider shall record: (i) in an appropriate deferred 
asset account, the Transmission Enhancement Charges associated with Required Transmission 
Enhancements for which collection is deferred in accordance with sections (b)(x)(B)(1) and 
(b)(x)(B)(2) above; and (ii) in an appropriate deferred liability account, the revenues associated 
with the Transmission Enhancement Charges that, absent the deferred charges, would have been 
due to Transmission Owners or to Transmission Owners’ customers as directed by the applicable 
Transmission Owner. At such time as collection of such deferred Transmission Enhancement 
Charges are permitted in accordance with sections (b)(x)(B)(1) and (b)(x)(B)(2) above, the 
deferred charges (along with appropriate interest) shall be collected from the Merchant 
Transmission Facility in equal installments over the twelve months following the 
commencement of the collection of the deferred charges. Such amounts shall be distributed to 
Transmission Owners or to Transmission Owners’ customers as directed by the applicable 
Transmission Owner, and the Transmission Provider shall make appropriate adjustments to the 
deferred asset and liability accounts.  Transmission Provider shall not be responsible for 
distributing revenues associated with deferred Transmission Enhancement Charges unless and 
until such charges are collected in accordance with this section (b)(x)(B), and uncollected 
deferred Transmission Enhancement Charges shall not be subject to Default Allocation 
Assessments to the Members pursuant to Operating Agreement, section 15.2.
(xi)
Consolidated Edison Company of New York.
(A) Cost responsibility 
assignments to Consolidated Edison Company of New York for Required Transmission 
Enhancements pursuant to this Schedule 12 with respect to the Firm Point-To-Point Service 
Agreements designated as Original Service Agreement No. 1873 and Original Service 
Agreement No. 1874 accepted by the Commission in Docket No. ER08-858 (“ConEd Service 
Agreements”) shall be in accordance with the terms and conditions of the settlement approved by 
the FERC in Docket No. ER08-858-000.  (B) All cost responsibility assignments for Required 
Transmission Enhancements pursuant to this Schedule 12 shall be adjusted at the commencement 
and termination of service under the ConEd Service Agreements to take account of the 
assignments under subsection (xi)(A) of this section.  
(xii)
Public Policy Projects.  
(A)
Transmission Facilities as defined in  Consolidated Transmission Owners 
Agreement, section 1.27 constructed by a Transmission Owner pursuant to a Public Policy 
Requirement but not included in a Regional Transmission Expansion Plan as a Required 
Transmission Enhancement, shall be as considered a Supplemental Project. 
Page 100

PDF page 149

(B)
If a transmission enhancement or expansion is proposed pursuant to 
Operating Agreement, Schedule 6, section 1.5.9(a) which is not a Supplemental Project (“State 
Agreement Public Policy Project”),  the Transmission Provider shall submit the assignment of 
costs to Responsible Customers proposed in connection with such State Agreement Public Policy 
Project to the Transmission Owners Agreement Administrative Committee for consideration and 
filing pursuant to Consolidated Transmission Owners Agreement, section 7.3 and Tariff, Part I, 
section 9.1(a).  Nothing in this section (b)(xii) shall prevent the Transmission Provider or the 
state governmental entities proposing such State Agreement Public Policy Project from filing a 
proposed assignment of costs to Responsible Customers for such project pursuant to Section 206 
of the Federal Power Act.
(xiii)
Replacement of Transmission Facilities.  Unless determined by PJM to be a 
Required Transmission Enhancement included in a Regional Transmission Expansion Plan, cost 
responsibility for the replacement of Transmission Facilities, as defined in Consolidated 
Transmission Owners Agreement, section 1.27, shall be assigned to the Zonal loads and Merchant 
Transmission Facilities responsible for the costs of the Transmission Facilities being replaced.
(xiv)    Multi-Driver Projects.  
(A)
Assignment of Proportional Multi-Driver Project Costs.  The Transmission 
Provider shall assign cost responsibility for Proportional Multi-Driver Projects in proportion 
to the relative percentage benefit that each driver of a Proportional Multi-Driver Project 
addresses, respectively, reliability violations or operational performance (“reliability”), 
economic constraints (“economic”) and/or Public Policy Requirements (“public policy”) as 
follows: 
(1)
As part of the open planning process provided for in Operating 
Agreement, Schedule 6, section 1.5.10(h), the Transmission Provider employs the 
Proportional Method to develop a Proportional Multi-Driver Project, by determining 
which of the following drivers a Proportional Multi-Driver Project addresses: 
reliability, economic, or public policy, and the extent to which each such driver 
contributes to the size, scope, and estimated costs of such Proportional Multi-Driver 
Project (irrespective of the reliability cost allocation treatment that is otherwise 
accorded an incremental market efficiency modification thereto pursuant to section 
(b)(v)(B) of this Schedule 12).  The Transmission Provider shall identify the 
contribution of each driver in terms of a percentage totaling 100 percent for all such 
drivers at the time that each Proportional Multi-Driver Project is submitted to the PJM 
Board for approval and included in the Regional Transmission Expansion Plan. The 
percentage contribution of each driver shall be based on the ratio of the estimated cost 
of each project that the Multi-Driver Project replaces to the total of the estimated costs 
of all projects combined into the Multi-Driver Project. 
(2)
Once a Proportional Multi-Driver Project is approved by the PJM Board, 
the percentage contributions of each driver shall not be changed unless the PJM Board 
Page 101

PDF page 150

subsequently approves an upgrade or modification to the Proportional Multi-Driver 
Project.  In that event, the cost responsibility for the Proportional Multi-Driver Project, 
including any costs incurred prior to the upgrade or modification, will be determined as 
if it were a new Proportional Multi-Driver Project, such that the percentage 
contribution for each driver shall be established anew.  
(B)
Assignment of Incremental Multi-Driver Project Costs.  The Transmission 
Provider shall assign cost responsibility for  Incremental Multi-Driver Projects as defined in 
Operating Agreement, Schedule 6, section 1.15B using the same methodology described in 
section (b)(xiv)(A)(1) above treating the estimated cost of modifying the original project as if 
it were the estimated cost of a separate project included in a Proportional Multi-Driver 
Project.  Any costs that had been expended on the original project prior its designation by 
Transmission Provider as an Incremental Multi-Driver Project shall be included in the 
calculation of the Incremental Multi-Driver Project pursuant to this section (b)(xiv)(B).  
(C)
The Transmission Provider shall separately assign cost responsibility for the 
costs assigned to each driver pursuant to this section (b)(xiv) in accordance with the provisions 
of this Schedule 12 governing the assignment of cost responsibility for a single driver project 
of each driver’s respective type (reliability, economic or public policy).  Except as provided in 
section (b)(xiv)(D) below, cost responsibility will be assigned based on the final voltage and 
configuration of the Multi-Driver Project determined in accordance with sections (b)(i), (b)(ii), 
or (b)(vi) of this Schedule 12. 
(D)     Notwithstanding the cost assignments that would otherwise be provided for in 
section (b)(xiv)(C) above, if a Multi-Driver Project includes a public policy driver that is the 
result of the State Agreement Approach provided for in Operating Agreement, Schedule 6, 
section 1.5.9 and is a Regional Facility as defined in section (b)(i) of this Schedule 12 and such 
Multi-Driver Project would not be a Regional Facility but for the inclusion of the public policy 
driver, then the percentage of costs of such Multi-Driver Project assigned to the non-public 
policy drivers in accordance with the procedures set forth in in section (b)(i)(A)(1) above shall 
be twenty percent (20%) and the percentage of costs assigned to the non-public policy drivers 
of such Multi-Driver Project in accordance section (b)(i)(A)(2) above shall be eighty percent 
(80%), and not the fifty percent (50%) cost responsibility percentages provided for in section 
(b)(i)(A)(i) and section (b)(i)(A)(2), respectively, of this Schedule 12. 
(xv) Reserved.
(xvi)
Required Transmission Enhancements Designed to Address Reliability 
Violations on Transmission Facilities Operating Below 200 kV. Notwithstanding section 
(b)(ii), above, cost responsibility for any Required Transmission Enhancements that are included 
in the Regional Transmission Expansion Plan to address reliability violations on Transmission 
Facilities that are designed to operate at below 200 kV and, pursuant to Operating Agreement, 
Schedule 6, section 1.5.8(n), were not included in an Operating Agreement, Schedule 6, section 
1.5.8(c) proposal window, shall be assigned to the Responsible Customers in the Zone where the 
Required Transmission Enhancement is to be located.
Page 102

PDF page 151

(xvii) Required Transmission Enhancements Constructed As Targeted Market 
Efficiency Projects Under The Midcontinent Independent Transmission System Operator, 
Inc. and PJM Interconnection, L.L.C. Coordinated System Plan.   Notwithstanding sections 
(b)(i), (b)(ii), (b)(iv), (b)(v), (b)(vi) and (b)(x)(B)(2) of this Schedule 12, cost responsibility for 
the costs of a Required Transmission Enhancement that is included in the Regional Transmission 
Expansion Plan because it is a Targeted Market Efficiency Project (“TMEP”) identified in the 
Coordinated System Plan periodically developed pursuant to the Joint Operating Agreement 
Between the Midcontinent Independent Transmission System Operator, Inc. and PJM 
Interconnection, L.L.C. (“PJM-MISO JOA”) and assigned to PJM pursuant to PJM-MISO JOA, 
section 9.4.4.2.5, shall be assigned among Zones and Merchant Transmission Facilities in 
accordance with this section (b)(xvii).  Using the Targeted Market Efficiency Project study 
conducted pursuant to PJM-MISO JOA, section 9.3.7.2(c) of in which the TMEP was identified, 
the Transmission Provider shall determine, in accordance with Tariff, Attachment K-Appendix, 
section 5.1, the average annual Transmission Congestion Charges experienced by Market Buyers 
in Zones and at Merchant Transmission Facilities attributable to the targeted Reciprocal 
Coordinated Flowgate during the two historical calendar years prior to the study year of the 
Targeted Market Efficiency Project study.  In making this determination, the Transmission 
Provider shall net any increases in Day-ahead and Real-time Prices paid by Market Buyers in a 
Zone or at a Merchant Transmission Facility against any decreases in Day-ahead and Real-time 
Prices paid by Market Buyers in such Zone or at such Merchant Transmission Facility 
attributable to the targeted Reciprocal Coordinated Flowgate.  Where a single TMEP is 
constructed to reduce Transmission Congestion Charges attributable to more than one targeted 
Reciprocal Coordinated Flowgate, the Transmission Provider shall net any increases in Day-
ahead and Real-time Prices paid by Market Buyers in a Zone or at a Merchant Transmission 
Facility against any decreases in Day-ahead and Real-time Prices paid by Market Buyers in such 
Zone or at such Merchant Transmission Facility attributable to all targeted Reciprocal 
Coordinated Flowgates.  Cost responsibility shall be assigned based on each Zone’s and 
Merchant Transmission Facility’s pro rata share of the sum of the net Transmission Congestion 
Charges paid by Market Buyers only of the Zones and Merchant Transmission Facilities in 
which Market Buyers experienced net Transmission Congestion Charges.
(xviii) Required Transmission Enhancements Designed to Address Stability Issues.
For purposes of the assignment of cost responsibility for Reliability Projects designed to address 
stability issues under subsection (b)(i)(A)(2)(a) and subsection (b)(ii)(A) of this Schedule 12, the 
Transmission Provider shall, using the same inputs and assumptions from the simulation that 
originally drove the need for the stability upgrade, perform a stability simulation that includes 
the stability upgrade under the worst fault condition. The worst fault condition shall be the fault 
condition in the simulation that produces the maximum rotor angle swing with the stability 
upgrade included.  For each load bus on the system, the difference between the highest and 
lowest voltage angle that occurs during the simulation of the worst fault condition will be 
recorded. Load buses having a voltage angle deviation less than 25 percent of the load bus with 
the largest voltage angle deviation will not be included in the cost allocation calculation. For the 
remaining load buses, the voltage angle deviation will be multiplied by the megawatt load at the 
bus obtained from the stability simulation model, or, in the case of a Merchant Transmission 
Facility, the Firm Transmission Withdrawal Rights at the bus. The products of the voltage angle 
deviation and megawatt load at each bus will be summed for each Responsible Zone. The 
Page 103

PDF page 152

Stability Deviation cost allocation for a Responsible Zone or Merchant Transmission Facility 
will be determined by dividing the sum of the load-weighted angle deviations for the 
Responsible Zone or Merchant Transmission Facility by the sum of the load-weighted angle 
deviations for each Responsible Zone and Merchant Transmission Facility. Transmission 
Provider shall round cost responsibility assignments to the nearest one-hundredth of one percent.
(c)
Determination of Transmission Enhancement Charges. In the event that any 
Transmission Owner recovers the cost of a Required Transmission Enhancement through a 
Transmission Enhancement Charge, such charge shall be determined as follows:
(1)
Transmission Provider shall identify in writing and post on the PJM Internet site 
the Required Transmission Enhancement(s) to which each Transmission Enhancement 
Charge corresponds. The Transmission Enhancement Charge with respect to a Required 
Transmission Enhancement shall recover the applicable Transmission Owner’s annual 
transmission revenue requirement associated with the Required Transmission 
Enhancement.
(2)  
Each Transmission Enhancement Charge shall be a monthly charge based on all 
costs and applicable incentives associated with a particular Required Transmission 
Enhancement for which the Transmission Owner is responsible. 
(3) 
A Transmission Owner’s annual transmission revenue requirement associated 
with a Required Transmission Enhancement shall be determined pursuant to either (i) a 
unilateral filing by the Transmission Owner under Section 205 of the Federal Power Act 
and the FERC’s rules and regulations thereunder; or (ii) a formula rate in effect 
applicable to the Transmission Owner’s rates for Network Integration Transmission 
Service, including the costs associated with Required Transmission Enhancements. 
(4) 
Each Transmission Enhancement Charge applicable to Network Customers and 
Non-Zone Network Customers shall be recalculated annually to reflect the annual 
revisions to the billing determinants used by the Transmission Provider to calculate 
charges to Network Customers for Network Integration Transmission Service under 
Tariff, Part III, section 34.1.  The Transmission Provider shall post on its Internet site by 
October 31 of each calendar year each recalculated Transmission Enhancement Charge 
that shall be effective during the subsequent calendar year.
(5) 
Each Transmission Enhancement Charge applicable to customers using Point-To-
Point Transmission Service shall be calculated monthly to reflect the billing determinants 
used by the Transmission Provider to determine charges for customers of Point-To-Point 
Transmission Service in accordance with Tariff, Part II, section 25. 
(6)
Each Transmission Enhancement Charge payable by an owner of a Merchant 
Transmission Facility pursuant to section (b) of this Schedule 12 shall be calculated as a 
fixed monthly charge. 
Page 104

PDF page 153

(7)
If a Transmission Owner chooses to recover the cost of Required Transmission 
Enhancements through the operation of a formula rate as described in section (a) of this 
Schedule 12, the Transmission Owner must make an informational filing with the 
Commission one year from the date the selecting Transmission Owner’s formula rates go 
into effect, and each year thereafter, providing a detailed list of the costs the 
Transmission Owner has incurred, and the revenues the Transmission Owner has 
received to provide service.
(d)
Recovery of Transmission Enhancement Charges.  
(1)
Responsible Customers shall pay Transmission Provider all applicable 
Transmission Enhancement Charges as required by this Schedule 12 in addition to 
all other charges for transmission service for which such Responsible Customers 
are responsible under the Tariff.
(2)
Transmission Provider shall collect all applicable Transmission Enhancement 
Charges from each Responsible Customer on a monthly basis.  Transmission 
Provider shall remit or credit all revenues received from Responsible Customers 
under this Schedule 12 to the Transmission Owner(s) that established such charge 
or to the appropriate authority in a region other than PJM in the case of 
Transmission Enhancement Charges established in such region in connection with 
a Required Transmission Enhancement constructed pursuant to an Appendix B 
Agreement, to be distributed in accordance with the applicable tariff or agreement 
governing the distribution of such charges in such region.
(e)
Crediting of Revenue from Transmission Enhancement Charges.  In recognition that 
a Transmission Owner’s charges for Network Integration Transmission Service set forth in 
Tariff, Attachment H are established based upon the Transmission Owner’s total cost of 
providing FERC-jurisdictional transmission service, including the costs associated with Required 
Transmission Enhancements, revenue from a Transmission Owner’s Transmission Enhancement 
Charges for a billing month shall be credited pursuant to this Schedule 12 to the Network 
Customers in the Transmission Owner’s Zone (including, where applicable, the Transmission 
Owner) and Transmission Customers purchasing Firm Point-to-Point Transmission Service for 
delivery in the Transmission Owner’s Zone in proportion to their Demand Charges (including 
any imputed Demand Charges for bundled service to Native Load Customers) for Network 
Integration Transmission Service and Reserved Capacity for Firm Point-to-Point Transmission 
Service; provided that such credits shall be reduced by the amount of any applicable incentives 
included in such Transmission Enhancement Charges.  
(f)
Recovery of Interconnection Reliability Reinforcement Costs.  
(1)
Customers Subject to Cost Responsibility for Interconnection Reliability 
Reinforcements. For each Fast Energization Process Cycle, the Transmission 
Provider shall determine cost responsibility for Interconnection Reliability 
Reinforcements identified and designated for construction pursuant to this section 
(f) of this Schedule 12.  Cost responsibility for Interconnection Reliability 
Page 105

PDF page 154

Reinforcements in a Fast Energization Cycle shall be assigned to Responsible 
Customers in Zones containing Transmission Customers taking Firm 
Transmission Service on behalf of Eligible Loads and Large Loads (“Large Load 
Zones”).  Generator Interconnection Customers in a given Cycle that are parties to 
a Generator Interconnection Agreement will pay a Generator Reliability 
Reinforcement Fee established in section (f)(vi) below.    
(2)
Determination of Cost Responsibility and Generator Allocation for 
Interconnection Reliability Reinforcements.  The Transmission Provider shall 
determine cost responsibility for Interconnection Reliability Reinforcements and 
the Generator Reliability Reinforcement Fee based on a proportional impact 
approach that considers all of the constraints identified in the Fast Energization 
Process Cycle.  
This proportional impact methodology will apply to thermal and non-thermal 
constraints, and will determine the pro rata share of impacts of Project 
Developers, Eligible Loads and Large Loads on the aggregate of constraints being 
alleviated by the portfolio of Interconnection Reliability Reinforcements as 
further described below and in the PJM Manuals.
The Transmission Provider shall determine each Project Developer, Eligible Load 
and Large Load’s proportional impact as follows:
(A)
With respect to the portfolio of Interconnection Reliability Reinforcements 
addressing thermal, stability and voltage constraints:
(1)
The Transmission Provider shall apply aggregation and thresholds 
as set forth in the PJM Manuals to identify the set of constrained 
facilities identified as having violations requiring mitigation 
through Interconnection Reliability Reinforcements in the Fast 
Energization Process Cycle studies, resulting in distribution 
factors, represented as decimal values or percentages, which 
express the portions of impact on constrained facilities from each 
Project Developer, Eligible Customer seeking Long-Term Firm 
Point-to-Point Transmission Service, Eligible Load, or Large Load.  
(2)
For purposes of determining MW impacts, each calculated 
distribution factor, if it exceeds the threshold set forth in the PJM 
Manuals, shall first be multiplied, for each Project Developer, 
Eligible Customer seeking Long-Term Firm Point-to-Point 
Transmission Service, Eligible Load or Large Load, by its 
requested MW value as studied in the Fast Energization Process.  
(3)
No allocation relating to a constrained facility shall result unless 
the calculated MW impact exceeds the thresholds set forth in the 
PJM Manuals.
Page 106

PDF page 155

(4)
All calculated MW impacts on constrained facilities above the 
relevant thresholds for each Project Developer, Eligible Customer 
seeking Long-Term Firm Point-to-Point Transmission Service, 
Eligible Load or Large Load are converted to proportional MW 
impacts representing the pro rata share of all MW impacts on the 
same constrained facility.
(5)
The proportional MW impacts are weighted using values as further 
described in the PJM Manuals resulting in a weighted proportional 
MW impact.
(6)
The percentage proportional impact values allocated for each Project 
Developer, Eligible Load or Large Load is based on its pro rata share 
of the weighted proportional MW impact relative to the total of 
weighted proportional MW impact for the Cycle.  For Project 
Developers, this value is the Generation Interconnection Customer’s 
Allocated Percentage (GCAP) as outlined in (f)(vi)(B).
(B)
With respect to the portfolio of Interconnection Reliability Reinforcements 
addressing short-circuit constraints, allocation will be based on contributing fault 
current impact on the circuit breaker’s applicable interrupting rating, as set forth 
in the PJM Manuals.
(C)
The aggregate impact values calculated pursuant to subsection (f)(ii)(A) 
and (f)(ii)(B) above shall determine the relative assignment of cost responsibility 
for Interconnection Reliability Reinforcements and the Generator Reliability 
Reinforcement Fee subject to the following rules:
 
(1)
The percentage proportional impacts of Eligible Load and Large 
Load Transmission Service Requests will be summed on a Zonal 
basis assigned to the relevant Transmission Owner Zones.
(2)
For purposes of this proportional allocation, the entire cost 
responsibility calculated pursuant to this subsection (f)(ii) will be 
assigned to Transmission Owner Zones based on their summed 
percentage proportional impacts.  Interconnection Reliability 
Reinforcement costs representing the relative contribution 
attributable to Generator Interconnection Customers shall be 
recovered from Generator Interconnection Customers through 
Generator Reliability Reinforcement Fees as set forth in subsection 
(f)(vi) below.
(D)
The Transmission Provider shall complete the analysis described in this 
subsection (f)(ii) within 30 days before Transmission Service Agreements and 
Generator Interconnection Agreements have been executed.  Within 30 days of 
Page 107

PDF page 156

the completion of this analysis, the Transmission Provider shall post on the PJM 
Internet Site the cost responsibility assignments determined pursuant to this 
section (f).  
(3)
Interconnection Reliability Reinforcements Charge.  The charge established to 
recover the revenue requirement with respect to an Interconnection Reliability 
Reinforcement is hereafter referred to as an “Interconnection Reliability 
Reinforcement Charge.”  Interconnection Reliability Reinforcement Charges of 
one or more Transmission Owners for Interconnection Reliability Reinforcements 
shall be established in accordance with this section (f) of Schedule 12.  
Transmission Provider shall assess an Interconnection Reliability Reinforcement 
Charge to Firm Transmission Customers in Zones based on the cost responsibility 
assignments determined pursuant to subsection (f)(ii) above.  The Interconnection 
Reliability Reinforcement Charge shall recover the applicable Transmission 
Owner's annual transmission revenue requirement associated with the 
Interconnection Reliability Reinforcements constructed and owned and/or 
financed by that Transmission Owner for a period of 15 years after an 
Interconnection Reliability Reinforcement enters service.  After this period, 
beginning with the next full calendar year, Transmission Provider will assign 
responsibility for and recover the remaining costs of the Interconnection 
Reliability Reinforcement in accordance with sections (a) through (e) of this 
Schedule 12. 
(A)
A Transmission Owner’s annual transmission revenue requirement 
associated with an Interconnection Reliability Reinforcement shall be determined 
pursuant to the formula rate in effect applicable to the Transmission Owner’s rates 
for Network Integration Transmission Service and Firm Contract Demand 
Transmission Service (“Firm Transmission Service”), including the costs 
associated with Interconnection Reliability Reinforcements.
(B)
Each Interconnection Reliability Reinforcement Charge applicable to Firm 
Transmission Customers shall be recalculated annually to reflect the annual 
revisions to the billing determinants used by the Transmission Provider to 
calculate charges for Firm Transmission Service.  The Transmission Provider 
shall post on its Internet site by October 31 of each calendar year each 
recalculated Interconnection Reliability Reinforcement Charge that shall be 
effective during the subsequent calendar year.
(C)
Each Interconnection Reliability Reinforcement Charge applicable to 
customers using Point-To-Point Transmission Service shall be calculated monthly 
to reflect the billing determinants used by the Transmission Provider to determine 
charges for customers of Point-To-Point Transmission Service in accordance with 
Tariff, Part II, section 25.
(4)
Recovery of Interconnection Reliability Reinforcement Charges.
Page 108

PDF page 157

(A)
Transmission Customers shall pay the Transmission Provider all 
applicable Interconnection Reliability Reinforcement Charge as required by this 
Schedule 12 in addition to all other charges for transmission service for which 
such Transmission Customers are responsible under the Tariff.
(B)
The Transmission Provider shall collect all applicable Interconnection 
Reliability Reinforcement Charges from each applicable Transmission Customer 
on a monthly basis. The Transmission Provider shall remit or credit all revenues 
received from Transmission Customers under this Schedule 12 to the 
Transmission Owner(s) owning the relevant Interconnection Reliability 
Reinforcements.
(5)
Crediting of Revenue from Interconnection Reliability Reinforcement 
Charges.  In recognition that a Transmission Owner’s charges for Firm 
Transmission Service set forth in Tariff, Attachment H are established based upon 
the Transmission Owner's total cost of providing FERC-jurisdictional 
transmission service, including the costs associated with Interconnection 
Reliability Reinforcements, revenue Interconnection Reliability Reinforcement 
Charges for a billing month shall be credited pursuant to this Schedule 12 to the 
Firm Transmission Customers in the Transmission Owner’s Zone (including, 
where applicable, the Transmission Owner) and Transmission Customers 
purchasing Firm Point-To-Point Transmission Service for delivery in the 
Transmission Owner's Zone in proportion to their Demand Charges (including 
any imputed Demand Charges for bundled service to Native Load Customers) for 
Network Integration Transmission Service and Reserved Capacity for Firm 
Contract Demand Transmission Service and Firm Point-To-Point Transmission 
Service; provided that such credits shall be reduced by the amount of any 
applicable incentives included in such Interconnection Reliability Reinforcement 
Charges.
(6)
Generator Reliability Reinforcement Fee.  The Transmission Provider shall 
recover the portion of the costs of Interconnection Reliability Reinforcements 
allocated to Generator Interconnection Customers in a Fast Energization Process 
Cycle, as determined pursuant to subsection (f)(ii) of this Schedule 12, through 
Generator Interconnection Reliability Reinforcement Fees as follows:
(A)
The Transmission Provider shall assess and each Generator 
Interconnection Customer will pay the Generator Reliability Reinforcement Fee 
beginning on the earlier of: (1) in the calendar year when the Generator 
Interconnection Customer’s facility achieves Commercial Operation, or (2) three 
years after the Commercial Operation date in the Customer’s original Generator 
Interconnection Agreement, and continuing for a period of 15 years from the 
Commercial Operation Date.
Page 109

PDF page 158

(B)
The Transmission Provider shall calculate the Generator Reliability 
Reinforcement Fee after each System Impact Study Phase as part of the Fast 
Energization Process as follows:
AGRRRF = GCAP X TRRGP x {[ACCC X (1 + ACCC)15]/[(1 + ACCC)15 – 1]}
Where:
GRRRF is the Generator Reliability Reinforcement Fee
GCAP is the Generator Interconnection Customer’s Allocated Percentage, which 
is the Generator Interconnection Customer’s allocated percentage for the portfolio 
of Interconnection Reliability Reinforcements from its New Service Request 
Cycle, determined pursuant to subsection (f)(ii) above.
 
TRRGP is the Total Reliability Reinforcement Gross Plant, which is based on the 
gross plant of all Interconnection Reliability Reinforcements included in the 
RTEP approved by the PJM Board with respect to the Generator Interconnection 
Customer’s New Service Request Cycle, and for which it has been allocated a 
percentage pursuant to subsection (f)(ii) above.  The gross plant amounts used in 
this calculation shall be based on the final estimated costs of the Interconnection 
Reliability Reinforcements as determined by the Transmission Provider through 
the Fast Energization Process.  
ACCC is the Annual Carrying Charge Component, which shall be calculated as 
the weighted average of the Weighted Average Cost of Capital for all 
Transmission Owners with Interconnection Reliability Reinforcements included 
in the RTEP approved by the PJM Board with respect to the Generator 
Interconnection Customer’s New Service Request Cycle.  The Weighted Average 
Cost of Capital values shall be derived from the applicable Transmission Owner’s 
formula rates, as set forth in Attachment H and in effect at the time the Annual 
Generator Reliability Reinforcement Fee is calculated.  For purposes of 
calculating such weighted average, each applicable Transmission Owner’s 
Weighted Average Cost of Capital shall be weighted based on the ratio of the 
final estimated costs of the Interconnection Reliability Reinforcements that it has 
been designated to construct and own and/or finance identified in the New Service 
Request Cycle that contains the Generator Interconnection Customer, to the final 
estimated costs for all Interconnection Reliability Reinforcements identified in the 
New Service Request Cycle that contains the Generator Interconnection 
Customer.  
Page 110

PDF page 159

SCHEDULE 20
Firm Contract Demand Transmission Service
For Eligible Load and Large Load
1)
Eligible Customer taking Firm Contract Demand Transmission Service in a Zone in 
which Network Integration Transmission Service rates are determined based on formula rates set 
forth in Attachment H shall pay a Monthly Demand Charge based on the Firm Contract Demand 
Transmission Service Amount (MW), as specified in Eligible Customer’s Service Agreement, 
which shall be determined as follows:
MDC = FCDTSA X RTZ/12
Where:
MDC is the monthly demand charge
FCDTSA is the Firm Contract Demand Transmission Service Amount (MW), as 
specified in Eligible Customer’s Service Agreement 
RTZ is the rate for Network Integration Transmission Service from Attachment H for the 
Zone in which the Eligible Customer’s Eligible Load or Large Load is located, stated in 
dollars per megawatt per year.  For purposes of establishing the RTZ component in the 
relevant Attachment H, the annual peak of the Zone shall be based on the sum of 
Network Customer Loads in the Zone and Firm Contract Demand Transmission Service 
Amounts for all Eligible Customers taking Firm Contract Demand Transmission Service 
in the Zone for the applicable peak period.
2)
Eligible Customers taking Firm Contract Demand Transmission Service in a Zone in 
which Network Integration Transmission Service rates are not established based on formula rates 
shall pay a Monthly Demand Charge based on the Firm Contract Demand Transmission Service 
Amount (MW), as specified in Eligible Customer’s Service Agreement, multiplied by a Zonal-
specific Firm Contract Demand Transmission Service rate filed with FERC pursuant to Section 
205 of the Federal Power Act.  Those rates will be posted on Transmission Provider’s website.
3)
Revenue Crediting.  Each month, credits will be applied to the Eligible Customer’s 
gross Monthly Demand Charge stated above associated with revenue collected from Non-Firm 
Contract Demand Transmission Service Charges in accordance with Schedule 19, based on each  
Eligible Customer’s pro rata share of the Zone’s annual peak load, from the most recent 12-
month period ending October 31.  The Eligible Customer’s pro rata share shall be based on the 
ratio of its Firm Contract Demand Transmission Service Amount during the peak period to the 
sum of Network Customer Loads in the Zone and Firm Contract Demand Transmission Service 
Amounts for all Eligible Customers taking Firm Contract Demand Transmission Service in the 
Zone for the applicable peak period.  The sum of these revenue credits will appear as a reduction 
to the gross monthly rate stated above on a Eligible Customer’s bill in that month for service 
under this schedule.  
Page 111

PDF page 160

4)
Transmission Enhancement Charges. In addition to the rates set forth in section (1) of 
this Schedule and any other applicable charges, the Eligible Customer shall also pay any 
Transmission Enhancement Charges for which it is designated as a Responsible Customer 
under Schedule 12 appended to the Tariff.
5)
Determination of Monthly Charges for ComEd Zone. On a monthly basis, revenue
credits shall be calculated based on the sum of ComEd’s share of revenues collected during the 
month from: (i) the PJM Border Rate under Schedule 7; (ii) Network Integration Transmission 
Service to Non-Zone Network Load under Attachment H-A; and (iii) any Point-To-Point 
Transmission Service where the Point of Receipt and the Point of Delivery are both internal to 
the ComEd Zone.  On this basis, the sum of these revenues will appear as a reduction to the gross 
monthly rate stated above on a Transmission Customer’s1 bill in that month for service under this 
schedule.
6)
Determination of Monthly Charges for AEP Zone. On a monthly basis, revenue 
credits shall be calculated based on the sum of AEP’s share of revenues collected during the 
month from: (i) the PJM Border Rate under Schedule 7; (ii) Network Integration Transmission 
Service to Non-Zone Network Load under Attachment H-A; and (iii) Firm Point-To-Point 
Transmission Service where the Point of Delivery is internal to the AEP Zone.  The sum of these 
revenue credits will appear as an adjustment (reduction) to the gross monthly rate stated above 
on a Eligible Customer’s bill in that month for service under this schedule.
7)
Other Supporting Facilities and Taxes.  In addition to the charges set forth in section 
(1) of this schedule, the Eligible Customer shall pay charges determined on a case-by-case basis 
for facilities necessary to provide Transmission Service at voltages lower than those shown 
in Attachment H for the applicable Zone(s) and any amounts necessary to reimburse 
the Transmission Provider for any amounts payable as sales, excise, “Btu,” carbon, value-added 
or similar taxes (other than taxes based upon or measured by net income) with respect to the 
amounts payable pursuant to the Tariff. 
1/ Transmission Customer is defined as an Eligible Customer that executes a Service Agreement, 
or requests PJM file an unexecuted Service Agreement, to receive transmission service under the 
Tariff.
Page 112

PDF page 161

SCHEDULE 21
Non-Firm Contract Demand Service
For Eligible Load and Large Load
1)
Eligible Customer taking Non-Firm Contract Demand Transmission Service in a Zone in 
which Network Integration Transmission Service rates are determined based on formula rates set 
forth in Attachment H shall pay for such service at a discounted reservation rate calculated by 
applying the Zone’s Annual Load Factor to the applicable Zonal Firm Contract Demand 
Transmission Service rate as follows:
Monthly Rate ($/MW): Zonal Firm Contract Demand Transmission Rate (RTZ) multiplied by 
the Zone’s Annual Load Factor, and divided by 12, where the Annual Load Factor is calculated 
as follows: Annual Load Factor = Zonal Annual Energy divided by (Zonal Peak Demand 
multiplied by 8,760 hours).  For purposes of this Schedule, Zonal Annual Energy shall be the 
total net energy for load measured as net generation plus energy receipts minus energy deliveries 
for the Zone from the 12-month period ending October 31 preceding the calendar year during 
which Non-Firm Contract Demand Transmission Service is taken.  For purposes of this 
Schedule, Zonal Peak Demand shall be the Zone’s annual peak load from the 12-month period 
ending October 31 preceding the calendar year during which Non-Firm Contract Demand 
Transmission Service is taken.
Weekly Rate ($/MW): Zonal Firm Contract Demand Transmission Rate (RTZ) multiplied by the 
Zone’s Annual Load Factor, and divided by 52, where the Annual Load Factor is calculated as 
follows: Annual Load Factor = Zonal Annual Energy divided by (Zonal Peak Demand multiplied 
by 8,760 hours).
Daily On-Peak Rate1 ($/MW): Weekly Rate divided by 5.
Daily Off-Peak Rate2 ($/MW): Weekly Rate divided by 7.
Hourly On-Peak Rate3 ($/MWh): Zonal Firm Contract Demand Transmission Rate (RTZ), 
multiplied by the Zone’s Annual Load Factor, and divided by 4,160.
Hourly Off-Peak Rate4 ($/MWh): Zonal Firm Contract Demand Transmission Rate (RTZ), 
multiplied by the Zone’s Annual Load Factor, divided by 8,760.
1/ Monday–Friday except the following holidays: New Years Day, Memorial Day, Independence 
Day, Labor Day, Thanksgiving Day, and Christmas Day.
2/ Saturday and Sunday and the following holidays: New Years Day, Memorial Day, 
Independence Day, Labor Day, Thanksgiving Day, and Christmas Day.
3/ 7:00 a.m. up to the hour ending 11:00 p.m.
4/ 11:00 p.m. up to the hour ending 7:00 a.m.
Page 113

PDF page 162

2)
Eligible Customers taking Non-Firm Contract Demand Transmission Service in a Zone in 
which Network Integration Transmission Service rates are not established based on formula rates 
shall pay for Non-Firm Contract Demand Transmission Service based on the amount of Non-
Firm Contract Demand Transmission Service reserved by the Eligible Customer in MW, 
multiplied by Zonal-specific Non-Firm Contract Demand Transmission Service rates filed with 
FERC pursuant to Section 205 of the Federal Power Act.  Those rates will be posted on 
Transmission Provider’s website.
3)
Discounts.  Three principal requirements apply to discounts for Non-Firm Contract 
Demand Transmission Service as follows: (1) any offer of a discount made by the Transmission 
Provider must be announced to all Eligible Customers solely by posting on the OASIS, (2) any 
customer-initiated requests for discounts (including requests for use by one’s wholesale 
merchant or an Affiliate’s use) must occur solely by posting on OASIS, and (3) once a discount 
is negotiated, details must be immediately posted on the OASIS.  For any discount agreed to by  
Transmission Provider, Transmission Provider must offer the same discounted transmission 
service rate for the same time period to all Eligible Customers taking Non-Firm Contract 
Demand Transmission Service.
4)
Revenue Crediting.  Revenues collected from Non-Firm Contract Demand Transmission 
Service Charges shall be credited to Eligible Customers taking Network Integration Transmission 
Service, Firm Contract Demand Transmission Service, and Firm Point-to-Point Transmission 
Service based on each Eligible Customer’s pro rata share of the Zone’s annual peak load based 
on the most recent 12-month period ending October 31.  The Eligible Customer’s pro rata share 
shall be based on the ratio of its Zone Network Load, Firm Point-To-Point Transmission Service 
and Firm Contract Demand Transmission Service Amount to the sum of Network Customer 
Loads in the Zone and Firm Contract Demand Transmission Service Amounts for all Eligible 
Customers taking Firm Contract Demand Transmission Service in the Zone, for the applicable 
peak period.  The sum of these revenue credits will appear as a reduction to the gross monthly 
rate for Firm Contract Demand Transmission Service on a Eligible Customer’s bill in that month. 
5)
Other Supporting Facilities and Taxes.  In addition to the charges set forth in section 
(1) of this schedule, the Eligible Customer shall pay charges determined on a case-by-case basis 
for facilities necessary to provide Transmission Service at voltages lower than those shown 
in Attachment H for the applicable Zone(s) and any amounts necessary to reimburse 
the Transmission Provider for any amounts payable as sales, excise, “Btu,” carbon, value-added 
or similar taxes (other than taxes based upon or measured by net income) with respect to the 
amounts payable pursuant to the Tariff.
Page 114

PDF page 163

SCHEDULE 22
Financial Penalty Charge for 
Unreserved Use by Eligible Load and Large Load
An Eligible Customer taking Firm Contract Demand Transmission Service, Non-Firm Contract 
Demand Transmission Service, or Interim Network Integration Transmission Service on behalf 
of Eligible Load or Large Load shall be subject to financial penalties for its unreserved use of the 
transmission system.
The financial penalty charge for unreserved use shall include two components: (1) a base penalty 
charge, which applies to each individual hour in which the reserved transmission service limit is 
exceeded, and (2) a penalty ratchet, which applies when such exceedances occur repeatedly.
Base Penalty Charge
When an Eligible Customer taking service on behalf of Eligible Load or Large Load exceeds its 
reserved transmission service limit, a base penalty charge shall be assessed for any hour in which 
at least one five-minute interval occurs during which the Eligible Customer’s telemetered load at 
the Point of Delivery exceeds its reserved transmission service limit.  This five-minute interval is 
defined as an Exceedance Interval, and such an hour is defined as an Exceedance Hour.  The 
base penalty charge shall apply to each Exceedance Hour.  
For an Eligible Customer taking only Firm Contract Demand Transmission Service, the 
reserved transmission service limit shall equal the Firm Contract Demand Transmission 
Service minus any curtailed MW.  
For an Eligible Customer taking only Non-Firm Contract Demand Transmission Service, 
the reserved transmission service limit shall equal the approved Non-Firm Contract 
Demand Transmission Service minus any curtailed MW.  
For an Eligible Customer taking Firm Contract Demand and Non-Firm Contract Demand 
Transmission Services, the reserved transmission service limit shall equal the Firm 
Contract Demand Transmission Service plus the approved Non-Firm Contract Demand 
Transmission Service minus any curtailed MW.  
For an Eligible Customer taking Interim Network Integration Transmission Service, the 
reserved transmission service limit shall equal the Interim Network Integration 
Transmission Service demand minus any curtailed MW.
Each five-minute interval beginning with the first minute of each hour shall constitute a 
separate interval and each hour from 0100 through 2400 shall constitute a separate hour 
for purposes of determining whether one or more exceedances have occurred.
Page 115

PDF page 164

The base penalty charge shall be applied to each Exceedance Hour and shall be calculated as:
Hourly Exceedance MW × Equivalent Hourly Firm Contract Demand (“FCD”) rate × 
number of Exceedance Intervals within the hour
Where:
Hourly Exceedance MW = Maximum telemetered load during the hour – Reserved 
Transmission Service Limit for the hour
Equivalent Hourly FCD rate = FCD rate / 8,760 hours
Penalty Ratchet
A penalty rachet shall apply when multiple Exceedance Hours occur during a particular time 
period in order to escalate the penalty charges as the frequency of unreserved transmission use 
increases.  
If more than one Exceedance Hour occurs on the same calendar day, an additional daily 
penalty shall apply.  
If exceedances occur on multiple calendar days within the same calendar week, an 
additional weekly penalty shall apply. 
If exceedances occur in multiple calendar weeks within the same calendar month, an 
additional monthly penalty shall apply.
If exceedances occur in multiple calendar months within the same calendar year, an 
additional yearly penalty shall apply.  
The penalty ratchet shall be based on an Eligible Customer’s exceedance pattern and applies 
escalating FCD-equivalent rates as the frequency of unreserved transmission use increases.  
Depending on whether exceedances occur within the same calendar day, calendar week, calendar 
month, or calendar year, the penalty ratchet shall apply daily, weekly, monthly, or annual penalty 
charges, respectively, as follows: 
Exceedance Pattern
Penalty Rate Applied
Multiple Exceedance Hours in a single calendar day
Daily FCD-Equivalent Rate
Multiple Exceedance Days within a calendar week
Weekly FCD-Equivalent Rate
Multiple Exceedance Weeks within a calendar month
Monthly FCD-Equivalent Rate
Multiple Exceedance Months within a calendar year
FCD Annual Rate
Daily Penalty Charge
The Daily Penalty Charge is calculated as:
Maximum Hourly Exceedance MW during the calendar day
× Daily FCD Equivalent Rate
Page 116

PDF page 165

× Number of Exceedance Hours in the calendar day
Weekly Penalty Charge
The Weekly Penalty Charge is calculated as:
Maximum Hourly Exceedance MW during the calendar week
× Weekly FCD Equivalent Rate
× Number of Exceedance Days in the calendar week
Monthly Penalty Charge
The Monthly Penalty Charge is calculated as:
Maximum Hourly Exceedance MW during the calendar month
× Monthly FCD Equivalent Rate
× Number of Exceedance Weeks in the calendar months
Annual Penalty Charge
The Annual Penalty Charge is calculated as:
Maximum Hourly Exceedance MW during the calendar year
× Annual FCD Rate
× Number of Exceedance Months in the calendar year
Revenues collected from Financial Penalty Charges shall be credited to Eligible Customers 
taking Firm Contract Demand Transmission Service, Non-Firm Contract Demand Transmission 
Service, Network Integration Transmission Service, and Interim Network Integration 
Transmission Service.  The Transmission Provider shall return revenues collected from Financial 
Penalty Charges on a monthly and annual basis as bill credits to Eligible Customers taking Firm 
Contact Demand Service, Non-Firm Contract Demand Transmission Service, Network 
Integration Transmission Service, and Interim Network Integration Transmission Service, who 
were not assessed Financial Penalty Charges during the year based on each Eligible Customer’s 
pro rata share of the Zone’s annual peak load based on the most recent 12-month period ending 
October 31.  The Eligible Customer’s pro rata share shall be based on the ratio of its Zone 
Network Load, Firm Contract Demand Transmission Service Amount, and Non-Firm Contract 
Transmission Service Amount to the sum of Network Customer Loads in the Zone and Firm and 
Non-Firm Contract Demand Transmission Service Amounts for all Eligible Customers taking 
Firm and Non-Firm Contract Demand Transmission Service in the Zone, for the applicable peak 
period.
Page 117

PDF page 166

Attachment B 
Revisions to the  
PJM Open Access Transmission Tariff  
(Marked Format) 
Page 1

PDF page 167

Definitions – R - S
Ramping Capability:
“Ramping Capability” shall mean the sustained rate of change of generator output, in megawatts 
per minute.
Real-time Congestion Price:
“Real-time Congestion Price” shall mean the Congestion Price resulting from the Office of the 
Interconnection’s dispatch of the PJM Interchange Energy Market in the Operating Day.
Real-time Loss Price:
“Real-time Loss Price” shall mean the Loss Price resulting from the Office of the 
Interconnection’s dispatch of the PJM Interchange Energy Market in the Operating Day.
Real-time Energy Market:
“Real-time Energy Market” shall mean the purchase or sale of energy and payment of 
Transmission Congestion Charges for quantity deviations from the Day-ahead Energy Market in 
the Operating Day.
Real-time Offer:
“Real-time Offer” shall mean a new offer or an update to a Market Seller’s existing cost-based or 
market-based offer for a clock hour, submitted for use after the close of the Day-ahead Energy 
Market.
Real-time Prices:
“Real-time Prices” shall mean the Locational Marginal Prices resulting from the Office of the 
Interconnection’s dispatch of the PJM Interchange Energy Market in the Operating Day.
Real-time Settlement Interval:
“Real-time Settlement Interval” shall mean the interval used by settlements, which shall be every 
five minutes.
Real-time System Energy Price:
“Real-time System Energy Price” shall mean the System Energy Price resulting from the Office 
of the Interconnection’s dispatch of the PJM Interchange Energy Market in the Operating Day.
Reasonable Efforts:
Page 2

PDF page 168

“Reasonable Efforts” shall mean, with respect to any action required to be made, attempted, or 
taken by an Interconnection Party or by a Construction Party under Tariff, Part IV or Part VI, an 
Interconnection Service Agreement, or a Construction Service Agreement, such efforts as are 
timely and consistent with Good Utility Practice and with efforts that such party would undertake 
for the protection of its own interests.
Receiving Party:
“Receiving Party” shall mean the entity receiving the capacity and energy transmitted by the 
Transmission Provider to Point(s) of Delivery.
Referral:
“Referral” shall mean a formal report of the Market Monitoring Unit to the Commission for 
investigation of behavior of a Market Participant, of behavior of PJM, or of a market design 
flaw, pursuant to Tariff, Attachment M, section IV.I.
Reference Resource:
“Reference Resource” shall mean a combustion turbine generating station, configured with a 
single General Electric Frame 7HA turbine with evaporative cooling, Selective Catalytic 
Reduction technology all CONE Areas, dual fuel capability, and a heat rate of 9.134 Mmbtu/ 
MWh. 
Regional Entity:
“Regional Entity” shall have the same meaning specified in the Operating Agreement.
Regional Transmission Expansion Plan:
“Regional Transmission Expansion Plan” shall mean the plan prepared by the Office of the 
Interconnection pursuant to Operating Agreement, Schedule 6 for the enhancement and 
expansion of the Transmission System in order to meet the demands for firm transmission 
service in the PJM Region.
Regional Transmission Group (RTG):
“Regional Transmission Group” or “RTG” shall mean a voluntary organization of transmission 
owners, transmission users and other entities approved by the Commission to efficiently 
coordinate transmission planning (and expansion), operation and use on a regional (and 
interregional) basis.
Regulation:
“Regulation” shall mean the capability of a specific generation resource or Demand Resource 
with appropriate telecommunications, control and response capability to separately increase and 
Page 3

PDF page 169

decrease its output or adjust load in response to a regulating control signal, in accordance with 
the specifications in the PJM Manuals.  Regulation is inclusive of Regulation-Down Service and 
Regulation-Up Service.
Regulation-Down Requirement:
“Regulation-Down Requirement” shall mean the required megawatts of performance-adjusted 
Regulation-Down Service capability to be maintained in a Regulation Zone. The Regulation-
Down Requirement is defined as a set megawatt value by hour in accordance with the PJM 
Manuals, and can increase to account for additional operational uncertainty.
Regulation-Down Service
“Regulation-Down Service” shall mean the capability of a specific generation resource or 
Demand Resource with appropriate telecommunications and response capability to increase and 
decrease its output in the downward range from a set point or adjust load in response to a 
regulating-down control signal, in accordance with the specification in the PJM Manuals.
Regulation-Up Requirement:
“Regulation-Up Requirement” shall mean the required megawatts of performance-adjusted
Regulation-Up Service capability to be maintained in a Regulation Zone. The Regulation-Up
Requirement is defined as a set megawatt value by hour in accordance with the PJM Manuals,
and can increase to account for additional operational uncertainty.
Regulation-Up Service
“Regulation-Up Service” shall mean the capability of a specific generation resource or Demand
Resource with appropriate telecommunications and response capability to increase and decrease
its output in the upward range from a set point or adjust load in response to a regulating-up
control signal, in accordance with the specification in the PJM Manuals.
Regulation Zone:
“Regulation Zone” shall mean any of those one or more geographic areas, each consisting of a 
combination of one or more Control Zone(s) as designated by the Office of the Interconnection 
in the PJM Manuals, relevant to provision of, and requirements for, regulation service.
Relevant Electric Retail Regulatory Authority:
“Relevant Electric Retail Regulatory Authority” shall mean an entity that has jurisdiction over 
and establishes prices and policies for competition for providers of retail electric service to end-
customers, such as the city council for a municipal utility, the governing board of a cooperative 
utility, the state public utility commission or any other such entity.
Reliability Assurance Agreement or PJM Reliability Assurance Agreement:
Page 4

PDF page 170

“Reliability Assurance Agreement” or “PJM Reliability Assurance Agreement” shall mean that 
certain Reliability Assurance Agreement Among Load Serving Entities in the PJM Region, on 
file with FERC as PJM Interconnection L.L.C. Rate Schedule FERC No. 44, and as amended 
from time to time thereafter.
Reliability Pricing Model Auction:
“Reliability Pricing Model Auction” or “RPM Auction” shall mean the Base Residual Auction or 
any Incremental Auction, or, for the 2016/2017 and 2017/2018 Delivery Years, any Capacity 
Performance Transition Incremental Auction.
Required Transmission Enhancements:
“Regional Transmission Enhancements” shall mean enhancements and expansions of the 
Transmission System that (1) a Regional Transmission Expansion Plan developed pursuant to 
Operating Agreement, Schedule 6 or (2) any joint planning or coordination agreement between 
PJM and another region or transmission planning authority set forth in Tariff, Schedule 12-
Appendix B (“Appendix B Agreement”) designates one or more of the Transmission Owner(s) to 
construct and own or finance.  Required Transmission Enhancements shall also include 
enhancements and expansions of facilities in another region or planning authority that meet the 
definition of transmission facilities pursuant to FERC’s Uniform System of Accounts or have 
been classified as transmission facilities in a ruling by FERC addressing such facilities 
constructed pursuant to an Appendix B Agreement cost responsibility for which has been 
assigned at least in part to PJM pursuant to such Appendix B Agreement. 
Reserved Capacity:
“Reserved Capacity” shall mean the maximum amount of capacity and energy that the 
Transmission Provider agrees to transmit for the Transmission Customer over the Transmission 
Provider’s Transmission System between the Point(s) of Receipt and the Point(s) of Delivery 
under Tariff, Part II.  Reserved Capacity shall be expressed in terms of whole megawatts on a 
sixty (60) minute interval (commencing on the clock hour) basis.
Reserve Penalty Factor:
“Reserve Penalty Factor” shall mean the cost, in $/MWh, associated with being unable to meet a 
specific reserve requirement in a Reserve Zone or Reserve Sub-zone.  A Reserve Penalty Factor 
will be defined for each reserve requirement in a Reserve Zone or Reserve Sub-zone.
Reserve Sub-zone:
“Reserve Sub-zone” shall mean any of those geographic areas wholly contained within a Reserve 
Zone, consisting of a combination of a portion of one or more Control Zone(s) as designated by 
the Office of the Interconnection in the PJM Manuals, relevant to provision of, and requirements 
for, reserve service.
Page 5

PDF page 171

Reserve Zone:
“Reserve Zone” shall mean any of those geographic areas consisting of a combination of one or 
more Control Zone(s), as designated by the Office of the Interconnection in the PJM Manuals, 
relevant to provision of, and requirements for, reserve service.
Residual Auction Revenue Rights:
“Residual Auction Revenue Rights” shall mean incremental stage 1 Auction Revenue Rights 
created within a Planning Period by an increase in transmission system capability, including the 
return to service of existing transmission capability, that was not modeled pursuant to Operating 
Agreement, Schedule 1, section 7.5 and the parallel provisions of  Tariff, Attachment K-
Appendix, section 7.5 in compliance with Operating Agreement, Schedule 1, section 7.4.2 (h) 
and the parallel provisions of Tariff, Attachment K-Appendix, section 7.4.2(h), and, if modeled, 
would have increased the amount of stage 1 Auction Revenue Rights allocated pursuant to 
Operating Agreement, Schedule 1, section 7.4.2 and the parallel provisions of Tariff, Attachment 
K-Appendix, section 7.4.2; provided that, the foregoing notwithstanding, Residual Auction 
Revenue Rights shall exclude: 1) Incremental Auction Revenue Rights allocated pursuant to 
Tariff, Part VI;  and 2) Auction Revenue Rights allocated to entities that are assigned cost 
responsibility pursuant to Operating Agreement, Schedule 6 for  transmission upgrades that 
create such rights.
Residual Metered Load:
“Residual Metered Load” shall mean all load remaining in an electric distribution company’s 
fully metered franchise area(s) or service territory(ies) after all nodally priced load of entities 
serving load in such area(s) or territory(ies) has been carved out.
Resource Substitution Charge:
“Resource Substitution Charge” shall mean a charge assessed on Capacity Market Buyers in an 
Incremental Auction to recover the cost of replacement Capacity Resources.
Responsible Customer: 
“Responsible Customer” shall mean customers using Interim Network Integration Transmission 
Service, Firm Contract Demand Transmission Service, Non-Firm Contract Demand 
Transmission Service, Point-to-Point Transmission Service and/or Network Integration 
Transmission Service and Merchant Transmission Facility owners, which are assigned cost 
responsibility for Transmission Enhancement Charges as determined pursuant to Tariff, 
Schedule 12.
Revenue Data for Settlements:
Page 6

PDF page 172

“Revenue Data for Settlements” shall mean energy quantities used in accounting and billing as 
determined pursuant to Tariff, Attachment K-Appendix and the corresponding provisions of 
Operating Agreement, Schedule 1.
RPM Seller Credit:
“RPM Seller Credit” shall mean an additional form of Unsecured Credit defined in Tariff, 
Attachment Q, section IV.
Scheduled Incremental Auctions:
“Scheduled Incremental Auctions” shall refer to the First, Second, or Third Incremental Auction.
Schedule of Work:
“Schedule of Work” shall mean that schedule attached to the Interconnection Construction 
Service Agreement setting forth the timing of work to be performed by the Constructing Entity 
pursuant to the Interconnection Construction Service Agreement, based upon the Facilities Study 
and subject to modification, as required, in accordance with Transmission Provider’s scope 
change process for interconnection projects set forth in the PJM Manuals.
Scope of Work:
“Scope of Work” shall mean that scope of the work attached as a schedule to the Interconnection 
Construction Service Agreement and to be performed by the Constructing Entity(ies) pursuant to 
the Interconnection Construction Service Agreement, provided that such Scope of Work may be 
modified, as required, in accordance with Transmission Provider’s scope change process for 
interconnection projects set forth in the PJM Manuals.
Seasonal Capacity Performance Resource:
“Seasonal Capacity Performance Resource” shall have the same meaning specified in Tariff, 
Attachment DD, section 5.5A.
Seasonal Facility Rating:
“Seasonal Facility Rating” shall mean a Transmission Facility Rating that:  
(a) Applies to a specified season, where seasons are defined by the Office of the Interconnection 
to include not fewer than four seasons in each year, and to reasonably reflect portions of the year 
where expected high temperatures are relatively consistent.
(b) Reflects an up-to-date forecast of ambient air temperature across the relevant season over 
which the rating applies.
Page 7

PDF page 173

(c) Is evaluated annually, if not more frequently, for each season in the future for which 
Transmission Service can be requested
Secondary Reserve: 
“Secondary Reserve” shall mean the reserve capability of generation resources that can be 
converted fully into energy or Economic Load Response Participant resources whose demand 
can be reduced within 30 minutes (less the capability of such resources to provide Primary 
Reserve), from the request of the Office of the Interconnection, regardless of whether the 
equipment providing the reserve is electrically synchronized to the Transmission System or not.
Secondary Systems:
“Secondary Systems” shall mean control or power circuits that operate below 600 volts, AC or 
DC, including, but not limited to, any hardware, control or protective devices, cables, 
conductors, electric raceways, secondary equipment panels, transducers, batteries, chargers, and 
voltage and current transformers.
Second Incremental Auction:
“Second Incremental Auction” shall mean an Incremental Auction conducted ten months before 
the Delivery Year to which it relates.  
Security:
“Security” shall mean the security provided by the New Service Customer pursuant to Tariff, 
section 212.4 or Tariff, Part VI, section 213.4 to secure the New Service Customer’s 
responsibility for Costs under the Interconnection Service Agreement or Upgrade Construction 
Service Agreement and Tariff, Part VI, section 217. 
Segment:
“Segment” shall have the same meaning as described in Operating Agreement, Schedule 1, 
section 3.2.3(e).
Self-Supply:
“Self-Supply” shall mean Capacity Resources secured by a Load-Serving Entity, by ownership 
or contract, outside a Reliability Pricing Model Auction, and used to meet obligations under this 
Attachment or the Reliability Assurance Agreement through submission in a Base Residual 
Auction or an Incremental Auction of a Sell Offer indicating such Market Seller’s intent that 
such Capacity Resource be Self-Supply.  Self-Supply may be either committed regardless of 
clearing price or submitted as a Sell Offer with a price bid. A Load Serving Entity's Sell Offer 
with a price bid for an owned or contracted Capacity Resource shall not be deemed “Self-
Supply,” unless it is designated as Self-Supply and used by the LSE to meet obligations under 
this Attachment or the Reliability Assurance Agreement.
Page 8

PDF page 174

Self-Supply Entity:
“Self-Supply Entity” shall mean the following types of Load Serving Entity that operate under 
long-standing business models: single customer entity, public power entity, or vertically 
integrated utility, where “vertically integrated utility” means a utility that owns generation, 
includes such generation in its regulated rates, and earns a regulated return on its investment in 
such generation or receives any cost recovery for such generation through bilateral contracts; 
“single customer entity”  means a Load Serving Entity that serves at retail only customers that 
are under common control with such Load Serving Entity, where such control means holding 
51% or more of the voting securities or voting interests of the Load Serving Entity and all its 
retail customers; and “public power entity” means cooperative and municipal utilities, including 
public power supply entities comprised of either or both of the same and rural electric 
cooperatives, and joint action agencies.
Self-Supply Seller:
“Self-Supply Seller” shall mean, for purposes of evaluating Buyer-Side Market Power, the 
following types of Load Serving Entities that operate under long-standing business models: 
vertically integrated utility or public power entity, where “vertically integrated utility” means a 
utility that owns generation, includes such generation in its state-regulated rates, and earns a 
state-regulated return on its investment in such generation; and “public power entity” means 
electric cooperatives that are either rate regulated by the state or have their long-term resource 
plan approved or otherwise reviewed and accepted by a Relevant Electric Retail Regulatory 
Authority and municipal utilities or joint action agencies that are subject to direct regulation by a 
Relevant Electric Retail Regulatory Authority.
Sell Offer:
“Sell Offer” shall mean an offer to sell Capacity Resources in a Base Residual Auction, 
Incremental Auction, or Reliability Backstop Auction.
Service Agreement:
“Service Agreement” shall mean the initial agreement and any amendments or supplements 
thereto entered into by the Transmission Customer and the Transmission Provider for service 
under the Tariff.
Service Commencement Date:
“Service Commencement Date” shall mean the date the Transmission Provider begins to provide 
service pursuant to the terms of an executed Service Agreement, or the date the Transmission 
Provider begins to provide service in accordance with Tariff, Part II, section 15.3 or Tariff, Part 
III, section 29.1.
Short-Term Firm Point-To-Point Transmission Service:
Page 9

PDF page 175

“Short-Term Firm Point-To-Point Transmission Service” shall mean Firm Point-To-Point 
Transmission Service under Tariff, Part II with a term of less than one year.
Short-term Project:
“Short-term Project” shall have the same meaning provided in the Operating Agreement.
Short-Term Resource Procurement Target:
“Short-Term Resource Procurement Target” shall mean, for Delivery Years through May 31, 
2018, as to the PJM Region, for purposes of the Base Residual Auction, 2.5% of the PJM Region 
Reliability Requirement determined for such Base Residual Auction,  for purposes of the First 
Incremental Auction, 2% of the of the PJM Region Reliability Requirement as calculated at the 
time of the Base Residual Auction; and, for purposes of the Second Incremental Auction, 1.5% 
of the of the PJM Region Reliability Requirement as calculated at the time of the Base Residual 
Auction; and, as to any Zone, an allocation of the PJM Region Short-Term Resource 
Procurement Target based on the Preliminary Zonal Forecast Peak Load, reduced by the amount 
of load served under the FRR Alternative.  For any LDA, the LDA Short-Term Resource 
Procurement Target shall be the sum of the Short-Term Resource Procurement Targets of all 
Zones in the LDA.
Short-Term Resource Procurement Target Applicable Share:
“Short-Term Resource Procurement Target Applicable Share” shall mean, for Delivery Years 
through May 31, 2018: (i) for the PJM Region, as to the First and Second Incremental Auctions, 
0.2 times the Short-Term Resource Procurement Target used in the Base Residual Auction and, 
as to the Third Incremental Auction for the PJM Region, 0.6 times such target; and (ii) for an 
LDA, as to the First and Second Incremental Auctions, 0.2 times the Short-Term Resource 
Procurement Target used in the Base Residual Auction for such LDA and, as to the Third 
Incremental Auction, 0.6 times such target. 
Site:
“Site” shall mean all of the real property, including but not limited to any leased real property 
and easements, on which the Customer Facility is situated and/or on which the Customer 
Interconnection Facilities are to be located.
Small Commercial Customer:
“Small Commercial Customer,” as used in RAA, Schedule 6 and Tariff, Attachment DD-1, shall 
mean a commercial retail electric end-use customer of an electric distribution company that 
participates in a mass market demand response program under the jurisdiction of a RERRA and 
satisfies the definition of a “small commercial customer” under the terms of the applicable 
RERRA’s program, provided that the customer has an annual peak demand no greater than 
100kW.
Page 10

PDF page 176

Small Generation Resource:
“Small Generation Resource” shall mean an Interconnection Customer’s device of 20 MW or 
less for the production and/or storage for later injection of electricity identified in an 
Interconnection Request, but shall not include the Interconnection Customer’s Interconnection 
Facilities.  This term shall include Energy Storage Resources and/or other devices for storage for 
later injection of energy.
Small Inverter Facility:
“Small Inverter Facility” shall mean an Energy Resource that is a certified small inverter-based 
facility no larger than 10 kW.
Small Inverter ISA:
“Small Inverter ISA” shall mean an agreement among Transmission Provider, Interconnection 
Customer, and Interconnected Transmission Owner regarding interconnection of a Small Inverter 
Facility under Tariff, Part IV, section 112B.
Special Member:
“Special Member” shall mean an entity that satisfies the requirements of Operating Agreement, 
Schedule 1, section 1.5A.02, and the parallel provisions of Tariff, Attachment K-Appendix, 
section 1.5A.02, or the special membership provisions established under the Emergency Load 
Response and Pre-Emergency Load Response Programs.
Spot Market Backup:
“Spot Market Backup” shall mean the purchase of energy from, or the delivery of energy to, the 
PJM Interchange Energy Market in quantities sufficient to complete the delivery or receipt 
obligations of a bilateral contract that has been curtailed or interrupted for any reason.
Spot Market Energy:
“Spot Market Energy” shall mean energy bought or sold by Market Participants through the PJM 
Interchange Energy Market at System Energy Prices determined as specified in Operating 
Agreement, Schedule 1, section 2, and the parallel provisions of Tariff, Attachment K-Appendix, 
section 2.
Start Additional Labor Costs:
“Start Additional Labor Costs” shall mean additional labor costs for startup required above 
normal station manning levels. 
Start Fuel:
Page 11

PDF page 177

For units without a soak process, “Start Fuel” shall consist of fuel consumed from first fire of the 
start process to first breaker closing, plus any fuel expended from last breaker opening to 
shutdown.
For units with a soak process, “Start Fuel” is fuel consumed from first fire of the start process 
(initial reactor criticality for nuclear units) to dispatchable output (including auxiliary boiler 
fuel), plus any fuel expended from last breaker opening to shutdown, excluding normal plant 
heating/auxiliary equipment fuel requirements.  Start Fuel included for each temperature state 
from breaker closure to dispatchable output shall not exceed the unit specific soak time period 
reviewed and approved as part of the unit-specific parameter process detailed in Tariff, 
Attachment K-Appendix, section 6.6(c) or the defaults below:
•
Cold Soak Time = 0.73 * unit specific Minimum Run Time (in hours)
•
Intermediate Soak Time = 0.61 * unit specific Minimum Run Time (in hours)
•
Hot Soak Time = 0.43 * unit specific Minimum Run Time (in hours)  
Start-Up Costs:
“Start-Up Costs” shall consist primarily of the cost of fuel, as determined by the unit’s start heat 
input (adjusted by the performance factor) times the fuel cost.  It also includes operating costs, 
Maintenance Adders, emissions allowances/adders, and station service cost.  Start-Up Costs can 
vary with the unit offline time being categorized in three unit temperature conditions: hot, 
intermediate and cold.
For units with a steam turbine and a soak process (nuclear, steam, and combined cycle), “Start 
Fuel” is fuel consumed from first fire of start process (initial reactor criticality for nuclear units): 
Start-Up Costs shall mean the net unit costs from PJM’s notification to the level at which the unit 
can follow PJM’s dispatch, and from last breaker open to shutdown.
For units without a steam turbine and no soak process (engines, combustion turbines, 
Intermittent Resources, and Energy Storage Resources): Start-Up Costs shall mean the unit costs 
from PJM’s notification to first breaker close and from last breaker open to shutdown.  
State:
“State” shall mean the District of Columbia and any State or Commonwealth of the United 
States.
State Commission:
“State Commission” shall mean any state regulatory agency having jurisdiction over retail 
electricity sales in any State in the PJM Region.
State Estimator:
Page 12

PDF page 178

“State Estimator” shall mean the computer model of power flows specified in Operating 
Agreement, Schedule 1, section 2.3 and the parallel provisions of Tariff, Attachment K-
Appendix, section 2.3.
State Subsidy:
“State Subsidy” shall mean a direct or indirect payment, concession, rebate, subsidy, non-
bypassable consumer charge, or other financial benefit that is as a result of any action, mandated 
process, or sponsored process of a state government, a political subdivision or agency of a state, 
or an electric cooperative formed pursuant to state law, and that 
(1) is derived from or connected to the procurement of (a) electricity or electric 
generation capacity sold at wholesale in interstate commerce, or (b) an attribute of the 
generation process for electricity or electric generation capacity sold at wholesale in 
interstate commerce; or
(2) will support the construction, development, or operation of a new or existing Capacity 
Resource; or 
(3) could have the effect of allowing the unit to clear in any PJM capacity auction. 
Notwithstanding the foregoing, State Subsidy shall not include (a) payments, concessions, 
rebates, subsidies, or incentives designed to incent, or participation in a program, contract or 
other arrangement that utilizes criteria designed to incent or promote, general industrial 
development in an area or designed to incent siting facilities in that county or locality rather than 
another county or locality; (b) state action that imposes a tax or assesses a charge utilizing the 
parameters of a regional program on a given set of resources notwithstanding the tax or cost 
having indirect benefits on resources not subject to the tax or cost (e.g., Regional Greenhouse 
Gas Initiative); (c) any indirect benefits to a Capacity Resource as a result of any transmission 
project approved as part of the Regional Transmission Expansion Plan; (d) any contract, legally 
enforceable obligation, or rate pursuant to the Public Utility Regulatory Policies Act or any other 
state-administered federal regulatory program (e.g., the Cross-State Air Pollution Rule); (e) any 
revenues from the sale or allocation, either direct or indirect, to an Entity Providing Supply 
Services to Default Retail Service Provider where such entity’s obligations was awarded through 
a state default procurement auction that was subject to independent oversight by a consultant or 
manager who certifies that the auction was conducted through a non-discriminatory and 
competitive bidding process, subject to the below condition, and provided further that nothing 
herein would exempt a Capacity Resource that would otherwise be subject to the minimum offer 
price rule pursuant to this Tariff; (f) any revenues for providing capacity as part of an FRR 
Capacity Plan or through bilateral transactions with FRR Entities; or (g) any voluntary and arm’s 
length bilateral transaction (including but not limited to those reported pursuant to Tariff, 
Attachment DD, section 4.6), such as a power purchase agreement or other similar contract 
where the buyer is a Self-Supply Entity and the transaction is (1) a short term transaction (one-
year or less) or (2) a long-term transaction that is the result of a competitive process that was not 
fuel-specific and is not used for the purpose of supporting uneconomic construction, 
development, or operation of the subject Capacity Resource, provided however that if the Self-
Supply Entity is responsible for offering the Capacity Resource into an RPM Auction, the 
specified amount of installed capacity purchased by such Self-Supply Entity shall be considered 
to receive a State Subsidy in the same manner, under the same conditions, and to the same extent 
as any other Capacity Resource of a Self-Supply Entity.  For purposes of subsection (e) of this 
Page 13

PDF page 179

definition, a state default procurement auction that has been certified to be a result of a non-
discriminatory and competitive bidding process shall:
(i)
have no conditions based on the ownership (except supplier diversity 
requirements or limits), location (except to meet PJM deliverability 
requirements), affiliation, fuel type, technology, or emissions of any resources or 
supply (except state-mandated renewable portfolio standards for which Capacity 
Resources are separately subject to the minimum offer price rule or eligible for an 
exemption);
(ii)
result in contracts between an Entity Providing Supply Services to Default Retail 
Service Provider and the electric distribution company for a retail default 
generation supply product and none of those contracts require that the retail 
obligation be sourced from any specific Capacity Resource or resource type as set 
forth in subsection (i) above; and
(iii)
establish market-based compensation for a retail default generation supply 
product that retail customers can avoid paying for by obtaining supply from a 
competitive retail supplier of their choice.
State of Charge:
“State of Charge” shall mean the quantity of physical energy stored in an Energy Storage 
Resource Model Participant or in the storage component of a Hybrid Resource in proportion to 
its maximum State of Charge capability. State of Charge is quantified as defined in the PJM 
Manuals.
State of Charge Management:
“State of Charge Management” shall mean the control of State of Charge of an Energy Storage 
Resource Market Participant or Hybrid Resource using minimum and maximum discharge (and, 
as applicable, charge) limits, changes in operating mode (as applicable), discharging (and, as 
applicable, charging) offer curves, and self-scheduling of non-dispatchable sales (and, as 
applicable, purchases) of energy in the PJM markets.  State of Charge Management shall not 
interfere with the obligation of a Market Seller of an Energy Storage Resource Model Participant
or of a Hybrid Resource to follow PJM dispatch, consistent with all other resources.
Station Power:
“Station Power” shall mean energy used for operating the electric equipment on the site of a 
generation facility located in the PJM Region or for the heating, lighting, air-conditioning and 
office equipment needs of buildings on the site of such a generation facility that are used in the 
operation, maintenance, or repair of the facility.  Station Power does not include any energy (i) 
used to power synchronous condensers; (ii) used for pumping at a pumped storage facility; (iii) 
used in association with restoration or black start service; or (iv) that is Direct Charging Energy.
Sub-Annual Resource Constraint:
Page 14

PDF page 180

“Sub-Annual Resource Constraint” shall mean, for the 2017/2018 Delivery Year and for FRR 
Capacity Plans the 2017/2018 and 2018/2019 Delivery Years, for the PJM Region or for each 
LDA for which the Office of the Interconnection is required under Tariff, Attachment DD, 
section 5.10(a) to establish a separate VRR Curve for a Delivery Year, a limit on the total 
amount of Unforced Capacity that can be committed as Limited Demand Resources and 
Extended Summer Demand Resources for the 2017/2018 Delivery Year in the PJM Region or in 
such LDA, calculated as the Sub-Annual Resource Reliability Target for the PJM Region or for 
such LDA, respectively, minus the Short-Term Resource Procurement Target for the PJM 
Region or for such LDA, respectively. 
Sub-Annual Resource Price Decrement:
“Sub-Annual Resource Price Decrement” shall mean, for the 2017/2018 Delivery Year, a 
difference between the clearing price for Extended Summer Demand Resources and the clearing 
price for Annual Resources, representing the cost to procure additional Annual Resources out of 
merit order when the Sub-Annual Resource Constraint is binding. 
Sub-Annual Resource Reliability Target: 
“Sub-Annual Reliability Target” for the PJM Region or an LDA, shall mean the maximum 
amount of the combination of Extended Summer Demand Resources and Limited Demand 
Resources in Unforced Capacity determined by PJM to be consistent with the maintenance of 
reliability, stated in Unforced Capacity, that shall be used to calculate the Minimum Annual 
Resource Requirement for Delivery Years through May 31, 2017 and the Sub-Annual Resource 
Constraint for the 2017/2018 and 2018/2019 Delivery Years.  As more fully set forth in the PJM 
Manuals, PJM calculates the Sub-Annual Resource Reliability Target, by first determining a 
reference annual loss of load expectation (“LOLE”) assuming no Demand Resources.  The 
calculation for the unconstrained portion of the PJM Region uses a daily distribution of loads 
under a range of weather scenarios (based on the most recent load forecast and iteratively 
shifting the load distributions to result in the Installed Reserve Margin established for the 
Delivery Year in question) and a weekly capacity distribution (based on the cumulative capacity 
availability distributions developed for the Installed Reserve Margin study for the Delivery Year 
in question).  The calculation for each relevant LDA uses a daily distribution of loads under a 
range of weather scenarios (based on the most recent load forecast for the Delivery Year in 
question) and a weekly capacity distribution (based on the cumulative capacity availability 
distributions developed for the Capacity Emergency Transfer Objective study for the Delivery 
Year in question).  For the relevant LDA calculation, the weekly capacity distributions are 
adjusted to reflect the Capacity Emergency Transfer Limit for the Delivery Year in question.
For both the PJM Region and LDA analyses, PJM then models the commitment of varying 
amounts of DR (displacing otherwise committed generation) as interruptible from May 1 through 
October 31 and unavailable from November 1 through April 30 and calculates the LOLE at each 
DR level.  The Extended Summer DR Reliability Target is the DR amount, stated as a percentage 
of the unrestricted peak load, that produces no more than a ten percent increase in the LOLE, 
compared to the reference value.  The Sub-Annual Resource Reliability Target shall be 
expressed as a percentage of the forecasted peak load of the PJM Region or such LDA and is 
Page 15

PDF page 181

converted to Unforced Capacity by multiplying [the reliability target percentage] times [the 
Forecast Pool Requirement] times [the DR Factor] times [the forecasted peak load of the PJM 
Region or such LDA, reduced by the amount of load served under the FRR Alternative].
Sub-meter:
“Sub-meter” shall mean a metering point for electricity consumption that does not include all 
electricity consumption for the end-use customer as defined by the electric distribution company 
account number.  PJM shall only accept sub-meter load data from end-use customers for 
measurement and verification of Regulation service as set forth in the Economic Load Response 
rules and PJM Manuals.
Summer-Period Capacity Performance Resource:
“Summer-Period Capacity Performance Resource” shall have the same meaning specified in 
Tariff, Attachment DD, section 5.5A.
Surplus Interconnection Customer:
“Surplus Interconnection Customer” shall mean either an Interconnection Customer whose 
Generating Facility is already interconnected to the PJM Transmission System or one of its 
affiliates, or an unaffiliated entity that submits a Surplus Interconnection Request to utilize 
Surplus Interconnection Service within the Transmission System in the PJM Region.  A Surplus 
Interconnection Customer is not a New Service Customer.   
Surplus Interconnection Request:
“Surplus Interconnection Request” shall mean a request submitted by a Surplus Interconnection 
Customer, pursuant to Tariff, Attachment RR, to utilize Surplus Interconnection Service within 
the Transmission System in the PJM Region.  A Surplus Interconnection Request is not a New 
Service Request.
Surplus Interconnection Service:
“Surplus Interconnection Service” shall mean any unneeded portion of Interconnection Service 
established in an Interconnection Service Agreement, such that if Surplus Interconnection 
Service is utilized, the total amount of Interconnection Service at the Point of Interconnection 
would remain the same.
Switching and Tagging Rules:
“Switching and Tagging Rules” shall mean the switching and tagging procedures of 
Interconnected Transmission Owners and Interconnection Customer as they may be amended 
from time to time. 
Synchronized Reserve:
Page 16

PDF page 182

“Synchronized Reserve” shall mean the reserve capability of generation resources that can be 
converted fully into energy or Economic Load Response Participant resources whose demand 
can be reduced within ten minutes from the request of the Office of the Interconnection 
dispatcher, and is provided by equipment that is electrically synchronized to the Transmission 
System.
Synchronized Reserve Event:
“Synchronized Reserve Event” shall mean a request from the Office of the Interconnection to 
generation resources and/or Economic Load Response Participant resources able, assigned or 
self-scheduled to provide Synchronized Reserve in one or more specified Reserve Zones or 
Reserve Sub-zones, within ten minutes, to increase the energy output or reduce load by the 
amount of assigned or self-scheduled Synchronized Reserve capability.
Synchronized Reserve Requirement:
“Synchronized Reserve Requirement” shall mean the megawatts required to be maintained in a 
Reserve Zone or Reserve Sub-zone as Synchronized Reserve, absent any increase to account for 
additional reserves scheduled to address operational uncertainty.  The Synchronized Reserve 
Requirement is calculated in accordance with the PJM Manuals.  This requirement can only be 
satisfied by Synchronized Reserve resources.
System Condition:
“System Condition” shall mean a specified condition on the Transmission Provider’s system or 
on a neighboring system, such as a constrained transmission element or flowgate, that may 
trigger Curtailment of Long-Term Firm Point-to-Point Transmission Service using the 
curtailment priority pursuant to Tariff, Part II, section 13.6.  Such conditions must be identified 
in the Transmission Customer’s Service Agreement.
System Energy Price:
“System Energy Price” shall mean the energy component of the Locational Marginal Price, 
which is the price at which the Market Seller has offered to supply an additional increment of 
energy from a resource, calculated as specified in Operating Agreement, Schedule 1, section 2 
and the parallel provisions of Tariff, Attachment K-Appendix, section 2.
System Impact Study:
“System Impact Study” shall mean an assessment by the Transmission Provider of (i) the 
adequacy of the Transmission System to accommodate a Completed Application, an 
Interconnection Request or an Upgrade Request, (ii) whether any additional costs may be 
incurred in order to provide such transmission service or to accommodate an Interconnection 
Request, and (iii) with respect to an Interconnection Request, an estimated date that an 
Interconnection Customer’s Customer Facility can be interconnected with the Transmission 
Page 17

PDF page 183

System and an estimate of the Interconnection Customer’s cost responsibility for the 
interconnection; and (iv) with respect to an Upgrade Request, the estimated cost of the requested 
system upgrades or expansion, or of the cost of the system upgrades or expansion, necessary to 
provide the requested incremental rights.
System Protection Facilities:
“System Protection Facilities” shall refer to the equipment required to protect (i) the 
Transmission System, other delivery systems and/or other generating systems connected to the 
Transmission System from faults or other electrical disturbance occurring at or on the Customer 
Facility, and (ii) the Customer Facility from faults or other electrical system disturbance 
occurring on the Transmission System or on other delivery systems and/or other generating 
systems to which the Transmission System is directly or indirectly connected.  System Protection 
Facilities shall include such protective and regulating devices as are identified in the Applicable 
Technical Requirements and Standards or that are required by Applicable Laws and Regulations 
or other Applicable Standards, or as are otherwise necessary to protect personnel and equipment 
and to minimize deleterious effects to the Transmission System arising from the Customer 
Facility.
Page 18

PDF page 184

Tariff, Part VIII, Subpart A, section 400
Definitions F
Facilities Study:
“Facilities Study” shall be an engineering study conducted by the Transmission Provider (in 
coordination with the affected Transmission Owner(s)) to: (1) determine the required 
modifications to the Transmission Provider’s Transmission System necessary to implement the 
conclusions of the System Impact Studies; and (2) complete any additional studies or analyses 
documented in the System Impact Studies or required by PJM Manuals, and determine the 
required modifications to the Transmission Provider's Transmission System based on the 
conclusions of such additional studies.  
Federal Power Act:
“Federal Power Act” shall mean the Federal Power Act, as amended, 16 U.S.C. §§ 791a, et seq.
FERC or Commission:
“FERC” or “Commission” shall mean the Federal Energy Regulatory Commission or any 
successor federal agency, commission or department exercising jurisdiction over the Tariff, 
Operating Agreement and Reliability Assurance Agreement.
Final Agreement Negotiation Phase:
“Final Agreement Negotiation Phase” shall mean the phase set forth in Tariff, Part VIII, Subpart 
D, section 411 to tender, negotiate, and execute any service agreement in Tariff, Part IX. 
Firm Transmission Service:
“Firm Transmission Service” shall mean any or a combination of Network Integration 
Transmission Service, Firm Point-To-Point Transmission Service, or Firm Contract Demand 
Transmission Service taken by an Eligible Customer.
Page 19

PDF page 185

Tariff, Part VIII, Subpart N
COST RECOVERY PROTECTION AND AGREEMENT
Page 20

PDF page 186

Tariff, Part VIII, Subpart N, section 441
Cost Recovery Protection for Firm Transmission Service
(a) Cost Recovery Assurances: With respect to Eligible Customers that intend to request any 
form of Firm Transmission Service from Transmission Provider on behalf of an Eligible Load or 
Large Load, a Transmission Owner shall either:
(i)
Enter into a Cost Recovery Agreement in the form found in Tariff, Part IX, 
Subpart P with the applicable Eligible Customer and Eligible Load or Large Load.  The 
Transmission Owner counterparty shall be the Transmission Owner that owns the transmission 
facilities with which the Eligible Load or Large Load will interconnect.  In the case of an 
Eligible Load or Large Load that will not directly interconnect with a Transmission Owner, the 
Transmission Owner counterparty shall be the Transmission Owner to which the applicable 
Eligible Customer is connected and from whom the Eligible Customer intends to take Firm 
Transmission Service.  The purpose of the Cost Recovery Agreement is to ensure the Eligible 
Customer takes a minimum level of Firm Transmission Service on behalf of the Eligible Load or 
Large Load based on the committed load level and the applicable rate for the Firm Transmission 
Service, or, if not, the Eligible Load or Large Load shall be required to make a shortfall payment 
representing any difference between the committed minimum level of service and the actual 
level of service taken.
(ii)
Enter into, subject to FERC acceptance, a separate agreement between at least the 
Transmission Owner and an Eligible Load or Large Load to prevent cost shifting among 
transmission customers.  Such separate agreement will be determined to adequately prevent cost 
shifts if such agreement, in conjunction with relevant federal and state regulatory requirements, 
including applicable retail service tariffs, results in minimum Firm Transmission Service and 
credit standards, or other comparable protections.
An Eligible Customer and/or Eligible Load or Large Load will be required to enter into and 
execute a Cost Recovery Agreement or an agreement that meets the standards set forth in 
subsection (a)(ii) in order to proceed past the Soft Close Date associated with the applicable PJM 
Fast Energization Cycle, and obtain any form of Firm Transmission Service from the 
Transmission Provider.
(b) Preservation of Legacy Treatment: No Cost Recovery Agreement or separate agreement 
under subsection (a) above shall be required with respect to Eligible Load or Large Loads 
covered by existing agreements that meet the criteria set forth in subsection (a)(ii) that have 
already been filed and are pending acceptance, or that have been accepted by FERC.  Any 
agreement entered into prior to the effective date of this subsection not filed with FERC will not 
be required to be filed and accepted by FERC; provided, however, in any complaint filed 
pursuant to Section 206 of the Federal Power Act in which it is claimed that such agreement is 
not just and reasonable or is unduly discriminatory within the meaning of the Federal Power Act, 
such agreement shall not be determined to be unjust and unreasonable or unduly discriminatory 
if it meets the standard set forth in subsection (a)(ii).
(c) Tender and Negotiation of Cost Recovery Agreement:  As applicable, consistent with 
subsections (a) and (b) above, Transmission Owner shall tender a draft of the Cost Recovery 
Page 21

PDF page 187

Agreement to Eligible Customer and Eligible Load or Large Load within 30 days of the 
completion of the Transmission Owner’s retail load interconnection study.  
Upon receipt of the draft Cost Recovery Agreement, Eligible Customer, as well as the Eligible 
Load or Large Load, shall provide the Transmission Owner with any written comments on the 
draft Cost Recovery Agreement within seven (7) days. The parties will conduct further 
negotiations as required, with such negotiations to be completed within twenty-five (25) days of 
the Transmission Owner’s tender of the draft Cost Recovery Agreement.  
(d) Execution and Filing of Cost Recovery Agreement: Not later than ten (10) days after the 
end of the negotiation period set forth in subsection (c) above, Eligible Customer and the Eligible 
Load or Large Load shall (i) execute the Cost Recovery Agreement and return it to Transmission 
Owner; and (ii) provide the Credit Support specified in the Cost Recovery Agreement.
If the Eligible Load or Large Load fails to execute the Cost Recovery Agreement or provide the 
required Credit Support in the specified time period, Eligible Customer shall not be permitted to 
proceed through the applicable Fast Energization Cycle.  
The Transmission Owner shall file any executed Cost Recovery Agreement, if required, with 
FERC within twenty-one (21) days of the other parties executing the Cost Recovery Agreement.
(e) Crediting of Termination Amounts: If the effective date of an Early Termination or Partial 
Termination, as defined in a Cost Recovery Agreement, occurs prior to the first Service Date 
specified in such agreement, and the Eligible Load or Large Load that is a party to that 
agreement is required to make a termination payment, as applicable, such termination payment 
or other amounts received pursuant to such obligation, including any security drawn on by 
Transmission Owner, shall be divided amongst the pool of Transmission Owners constructing
facilities needed to provide the related transmission service, but which will no longer be 
constructed, including the Transmission Owner that is a party to the Cost Recovery Agreement, 
as follows:
(i)
Within thirty (30) days of such termination, the Transmission Owner that is party 
to the Cost Recovery Agreement (referred to herein as the “contracting Transmission Owner”) 
shall notify all other Transmission Owners that have been designated to construct and own 
Interconnection Reliability Reinforcements necessary to provide Firm Transmission Service to 
an Eligible Customer on behalf of the terminating Eligible Load or Large Load (referred to 
herein as the “third party Transmission Owners”) of such termination.  For purposes of this 
subsection, third party Transmission Owners shall include all Transmission Owners designated 
to construct and own Interconnection Reliability Reinforcements identified in the PJM Fast 
Energization Cycle in which the terminating Eligible Load or Large Load was studied, and for 
which the contracting Transmission Owner’s Zone received a cost responsibility share.
(ii)
Each third-party Transmission Owner shall, within thirty (30) days of the deadline 
for filings its FERC Form 1 that includes all Eligible Costs, provide an account of such Eligible 
Costs to the contracting Transmission Owner.  For purposes of this subsection “Eligible Costs” 
consist of all expenditures, costs, and cancellation fees incurred or due to commitments made by 
the third-party Transmission Owner to engineer, design, procure, construct, own, operate, 
Page 22

PDF page 188

maintain, and service the Interconnection Reliability Reinforcements needed to serve the Eligible 
Customer taking transmission service on behalf of the Eligible Load or Large Load, but which 
will no longer be constructed, which (a) are incurred through the end of the calendar year in 
which notice of termination was received from the contracting Transmission Owner, and (b) are 
included in amounts reported in the Transmission Owner’s FERC Form 1 covering that calendar 
year.  
Any failure by a third-party Transmission Owner to provide such information within the 
timeframe above shall bar said Transmission Owner from receiving a portion of amounts paid by 
Eligible Load or Large Load as set forth below.
(iii)
Within thirty (30) days of (a) receiving all Transmission Owner accountings in 
accordance with subsection (ii) above, and (b) receipt of termination amounts from the Eligible 
Load or Large Load that is party to the Cost Recovery Agreement,  the contracting Transmission 
Owner shall divide such termination amounts among itself and the pool of third-party 
Transmission Owners based on each Transmission Owner’s pro rata share of the total amount of 
applicable expenditures, costs and cancellation fees, and disburse such amounts to the third-party 
Transmission Owners accordingly.  
For purposes of determining these pro rata shares, the contracting Transmission Owner shall be 
permitted to include Eligible Costs associated not only with its applicable Interconnection 
Reliability Reinforcements but also any other transmission facilities, including Supplemental 
Projects and Direct Connection Facilities, that it was constructing in order to provide 
interconnection or transmission service to the Eligible Load or Large Load, or Eligible Customer 
taking transmission service on behalf of the Eligible Load or Large Load.
To the extent that additional termination funds are received or collected from the Eligible Load 
or Large Load after an initial distribution is made under this subsection, contracting 
Transmission Owner will make additional disbursements using the same methodology within 
fifteen (15) days of receipt of such amounts.
(iv)
Nothing in this subsection (e) is intended or shall be interpreted to prevent any 
Transmission Owner from seeking cost recovery through an abandoned plant recovery filing 
made with FERC or through any other proceeding, except insofar as the Transmission Owner has 
received amounts pursuant to the process set forth in this subsection (e), it shall be prohibited 
from requesting recovery of such amounts in any future proceeding.
(v)
To the extent a Transmission Owner elects to satisfy its obligation under 
subsection (a) above through a separate agreement as described in subsection (a)(ii), it shall 
include in such separate agreement reasonably comparable termination payment crediting 
provisions as set forth in this subsection (e), as determined by FERC.
(vi)
Any disputes under this subsection (e) shall be subject to the dispute resolution 
procedure set forth in Schedule 5 of the Operating Agreement.
Page 23

PDF page 189

Tariff, Part IX, Subpart P
FORM OF
COST RECOVERY AGREEMENT
Page 24

PDF page 190

Service Agreement No. [____]
COST RECOVERY AGREEMENT
Between
[TRANSMISSION OWNER] 
Transmission Owner
and
[LARGE LOAD CUSTOMER]
Large Load Customer
and 
[ELIGIBLE CUSTOMER]
Eligible Customer
Page 25

PDF page 191

Service Agreement No. [____]
COST RECOVERY AGREEMENT
This Cost Recovery Agreement (“Agreement” or “CRA”) is made and entered into as of 
[Insert Date] by and among [Transmission Owner], a [State and Entity Type] (“Transmission 
Owner”) and [Large Load Customer], a [State and Entity Type] (“Large Load Customer”), and
[Eligible Customer], a [State and Entity Type] (“Eligible Customer”). Transmission Owner, 
Eligible Customer, and Large Load Customer are referred to individually as a “Party” and 
collectively as the “Parties.” 
Large Load Customer will be responsible for all payment and Credit Support obligations 
assigned to Large Load Customer under this CRA. Eligible Customer will remain responsible for 
the transmission-service, information-sharing, and administrative obligations expressly assigned 
to Eligible Customer under this CRA.
RECITALS
WHEREAS, Large Load Customer intends to construct, maintain, and operate new or 
modified facilities located at or near [Facility Address] that will constitute a Large Load (the 
“Large Load Facilities”), with an anticipated initial service date of [Date] (the “Commercial 
Operation Date”);
WHEREAS, Large Load Customer has completed retail interconnection studies 
conducted by Transmission Owner and/or one or more of its affiliates;
WHEREAS,
following completion of the applicable Transmission Owner’s 
interconnection study process, the Parties are entering into this CRA based on the Initial Load 
Commitment, proposed load ramp, and anticipated Service Dates identified in Exhibit A;
WHEREAS, Eligible Customer intends to request Network Integration Transmission 
Service (“NITS”), Firm Point-to-Point Transmission Service, or Firm Contract Demand 
Transmission Service (“FCDS”) under the PJM Open Access Transmission Tariff (“PJM Tariff”) 
on behalf of the Large Load Customer to serve the Large Load Facilities , each of which 
constitutes “Firm Transmission Service” under this CRA;
WHEREAS, Exhibit A identifies the initial amount and type of Firm Transmission 
Service to be requested by Eligible Customer on behalf of Large Load Customer, together with 
the load ramp and anticipated Service Dates;
WHEREAS, following completion of the applicable application and study process to 
obtain the Firm Transmission Service, Exhibit A and the related calculations under this CRA will 
be updated to reflect the type, amount, and timing of Firm Transmission Service established in 
the Final PJM Agreement;
WHEREAS, in reliance on the Firm Load Commitment and in accordance with the PJM 
Tariff and other applicable agreements, the Transmission Owner intends to construct, own, 
Page 26

PDF page 192

operate, maintain, service, and recover the costs associated with transmission facilities necessary 
to serve the Large Load Facilities;
WHEREAS, this CRA establishes the payment and Credit Support obligations described 
herein and allocates the financial risk arising if Firm Transmission Service-related revenues 
attributable to service actually taken for the Large Load Facilities are less than the Committed 
Revenue Contribution.
NOW, THEREFORE, in consideration of the premises and the mutual covenants and 
undertakings set forth herein, the receipt and sufficiency of which are acknowledged, the Parties, 
intending to be legally bound, agree as follows:
ARTICLE 1
DEFINITIONS
1.0
Defined Terms 
Capitalized terms used in this CRA have the meanings set forth below. Capitalized terms used 
but not defined in this CRA have the meanings set forth in the PJM Tariff.
(a)
“Actual Revenue Contribution” means, for each Measurement Period, the Firm 
Transmission Service-related revenues attributable to Firm Transmission Service actually 
taken by 
Eligible Customer to serve the Large Load Facilities, as calculated in 
accordance with Section 5.2 and Exhibit B.
(b) 
“Agreement” or “CRA” means this Cost Recovery Agreement, including its Exhibits and 
any amendments that become effective in accordance with this CRA and applicable law.
(c)
“Applicable Credits” means the amounts identified in Article 9 and Exhibit D, Section 4, 
that are deducted in calculating the Early Termination Amount or Partial Termination 
Amount, without duplication.
(d)
“Applicable Firm Transmission Service Rate” means, for each Measurement Period, the 
Transmission Owner’s rate or rates then in effect under the PJM Tariff for the applicable 
Firm Transmission Service in the applicable Transmission Zone, as used to calculate the 
charges corresponding to the Firm Load Commitment.
(e)
“Applicable Termination Percentage” means the percentage set forth in Exhibit D for the 
period in which the termination or Partial Termination becomes effective.
(f)
“Business Day” means any day other than a Saturday, Sunday, or holiday recognized by 
the North American Electric Reliability Corporation.
(g)
“Commercial Operation Date” means the anticipated initial service date for the Large 
Load Facilities identified in Exhibit A.
(h)
“Committed Revenue Contribution”
means, for each Measurement Period, the 
contractually required portion of the Full Firm Transmission Service Benchmark, 
calculated by applying the Minimum Commitment Percentage in accordance with Section 
5.1 and Exhibit B.
(i)
“Credit Support” means the financial security that Large Load Customer is required to 
provide and maintain under Section 6.1 to secure Large Load Customer’s payment and 
other financial obligations under this CRA.
Page 27

PDF page 193

(j)
“Credit Support Requirement” means the amount of Credit Support that Large Load 
Customer is required to cause to be provided and maintained, as calculated in accordance 
with Section 6.5 and Exhibit C based on the aggregate Projected Full Firm Transmission 
Service Benchmarks for all Measurement Periods remaining in the Term, including any 
portion of the applicable Measurement Period that remains incomplete. Before the 
recalculation required under Section 3.2, the Credit Support Requirement shall be the 
Initial Credit Support Requirement.
(k)
“Effective Date” means the date on which this CRA becomes effective as set forth in 
Section 4.1.
(l)
“Early Termination Amount” means the amount payable by Large Load Customer upon 
a termination of this CRA for which an Early Termination Amount is required under 
Article 9, as calculated in accordance with Exhibit D.
(m)
“Early Termination Offset Amount” means the Firm Transmission Service-related 
revenues received by Transmission Owner during the period corresponding to the 
remaining fixed period from incremental replacement load served at the same Point of 
Delivery, to the extent those revenues correspond to the revenue exposure included in the 
Early Termination Amount or Partial Termination Amount, as determined in accordance 
with Section 9.9.
(n)
“Eligible Customer” means the Person identified as  Eligible Customer in the preamble to 
this CRA, which is an Eligible Customer under the PJM Tariff and the entity responsible 
for taking Firm Transmission Service on behalf of Large Load Customer to serve the 
Large Load Facilities. Eligible Customer is responsible only for the obligations expressly 
assigned to Eligible Customer under this CRA and is not responsible for Large Load 
Customer’s payment or Credit Support obligations.
(o)
“FERC” means the Federal Energy Regulatory Commission or any successor agency.
(p)
“Final PJM Agreement” means the final Transmission Service Agreement or other 
agreement executed under the PJM Tariff that identifies the Firm Transmission Service to 
be taken by Eligible Customer on behalf of Large Load Customer.
(q)
“Firm Load Commitment” means the amount of firm load identified in Exhibit A, 
together with the corresponding level of Firm Transmission Service that Eligible 
Customer has committed to take on behalf of  Large Load Customer and any associated 
load-ramp milestones and Service Dates.
(r)
“Firm Transmission Service” means NITS, Firm Point-to-Point Transmission Service, or 
FCDS, as applicable, requested or taken by Eligible Customer under the PJM Tariff on 
behalf of Large Load Customer to serve the Large Load Facilities. 
(s)
“Full Firm Transmission Service Benchmark” means, for each Measurement Period, the 
charges that would apply under the Applicable Firm Transmission Service Rate and 
applicable billing determinants if Eligible Customer took Firm Transmission Service 
corresponding to the Firm Load Commitment scheduled to apply during that 
Measurement Period, as calculated in accordance with Section 5.1 and Exhibit B.
(t)
“Force Majeure” has the meaning set forth in Article 12.
(u)
“FCDS” means Firm Contract Demand Transmission Service under the PJM Tariff.
(v)
“Initial Load Commitment” means the initial amount of Firm Transmission Service to be 
requested by Eligible Customer on behalf of Large Load Customer, together with the 
proposed load ramp and anticipated Service Dates identified in Exhibit A at execution of 
this CRA.
Page 28

PDF page 194

(w)
“Initial Credit Support Requirement” means the amount of Credit Support identified in 
Exhibit C at execution by the Parties of this CRA based on the Initial Load Commitment, 
anticipated Service Dates, and aggregate Projected Full Firm Transmission Service 
Benchmarks for the Term, calculated in accordance with  the methodology specified in 
Exhibit C.
(x)
“Large Load” shall mean end-use customer(s) load that has a cumulative peak load of 50 
megawatts or greater at a single electrical site behind one or more points of 
interconnection, where for configurations involving multiple affiliated load facilities or 
multiple points of interconnection with affiliated load facilities behind them, all affiliated 
load facilities within a one-mile radius will be considered a single electrical site as further 
described in the PJM Manuals.
(y)
“Large Load Customer” means the Person identified in Exhibit A that owns, operates, 
leases, or otherwise controls the Large Load Facilities and on whose behalf Eligible 
Customer takes Firm Transmission Service to serve the Large Load Facilities. Large 
Load Customer is a Party to this CRA and is directly responsible for the payment and 
Credit Support obligations assigned to Large Load Customer under this CRA.
(z)
“Large Load Facilities” means the new or modified facilities identified in Exhibit A that 
constitute the Large Load.
(aa)
“Measurement Period”  means each period, not to exceed one year, corresponding to 
Transmission Owner’s applicable formula rate cycle, or portion thereof, beginning on the 
first Service Date and continuing through the end of the Term, as specified in Exhibit A.
(bb)
“Minimum Commitment Percentage” means the percentage specified in Exhibit A that is 
applied to the Full Firm Transmission Service Benchmark to calculate the Committed 
Revenue Contribution, which percentage shall be no less than 80% and no greater than 
100%, per the schedule set forth in Exhibit A below.
(cc)
“MW” means megawatts.
(dd)
“NITS” means Network Integration Transmission Service provided pursuant to the PJM 
Tariff, Part III.
(ee)
“Partial Termination Amount” means the amount payable by Large Load Customer upon 
a permanent reduction of a specified portion of the Firm Load Commitment under 
Section 9.2, as calculated in accordance with Section 9.8 and Exhibit D.
(ff)
“Person” means an individual, corporation, limited liability company, partnership, 
association, trust, governmental authority, or other legal entity.
(gg)
“PJM” means PJM Interconnection, L.L.C. or its successor.
(hh)
“PJM Tariff” means the PJM Open Access Transmission Tariff, as accepted by FERC 
and effective from time to time.
(ii)
“Projected Committed Revenue Contributions” means the aggregate amounts projected to 
constitute Committed Revenue Contributions during the applicable period, calculated by 
applying the Minimum Commitment Percentage to the Projected Full Firm Transmission 
Service Benchmark for each applicable Measurement Period. 
(jj)
“Project Development Costs” means all expenditures, costs, and cancellation fees 
incurred, or due to commitments made by the Transmission Owner or other transmission 
owners to engineer, design, procure, construct, own, operate, maintain, and service the 
necessary transmission facilities needed to serve the Large Load Customer that are 
intended to be placed into transmission rate base and recovered through transmission 
rates.  
Page 29

PDF page 195

(kk)
“Projected Full Firm Transmission Service Benchmark” means, for each applicable 
Measurement Period, 100% of the Firm Transmission Service-related charges projected 
to apply if Eligible Customer takes Firm Transmission Service corresponding to the 
Initial Load Commitment or Firm Load Commitment, as applicable, calculated in 
accordance with Exhibit C.
(ll)
“Service Date” means (i) before execution of the Final PJM Agreement, each anticipated 
date identified in Exhibit A on which the Initial Load Commitment, or a portion thereof, 
is expected to become effective; and (ii) after execution of the Final PJM Agreement, 
each date identified in Exhibit A as updated pursuant to Section 3.2 on which the Firm 
Load Commitment, or a specified portion thereof under an applicable load ramp, is 
scheduled to become effective..
(mm) “Shortfall Amount” means, for each Measurement Period, the amount, if any, by which 
the Committed Revenue Contribution exceeds the Actual Revenue Contribution, as 
calculated in accordance with Section 5.3 and Exhibit B.
(nn)
“Term” has the meaning set forth in Section 4.2.
(oo)
“Transmission Owner” means the PJM Transmission Owner identified in the preamble to 
this CRA.
(pp)
“Transmission System” shall mean the facilities controlled or operated by PJM that are 
used to provide transmission service under Part II and Part III of the PJM Tariff. 
(qq)
“Transmission Zone” means the transmission zone identified in Exhibit A in which the 
Large Load Facilities are located.
ARTICLE 2
RECITALS
2.1
Recitals
The statements set forth in the recitals above are hereby incorporated herein into the terms and 
conditions of this CRA as if fully set forth herein.
ARTICLE 3
FIRM LOAD COMMITMENT
3.1
Initial Load Commitment and Firm Load Commitment
At execution of this CRA, the Initial Load Commitment shall be established using the amount 
and type of Firm Transmission Service that Eligible Customer intends to request from PJM on 
behalf of Large Load Customer through the applicable application and study process, together 
with the proposed load ramp and anticipated Service Dates identified in Exhibit A.
Following execution of the Final PJM Agreement, the Firm Load Commitment applicable during 
each Measurement Period shall be the amount and type of Firm Transmission Service that the 
Eligible Customer takes on behalf of the Large Load during each Measurement Period, as set 
forth in Exhibit A.  This amount shall be based on the amount of load for the Large Load 
scheduled to be in service during each Measurement Period, or the amount of Firm Transmission 
Service that the Eligible Customer has contracted for on behalf of the Large Load.
Page 30

PDF page 196

If Exhibit A establishes a load ramp, consistent with the amount of Firm Transmission Service 
that the Eligible Customer has contracted for on behalf of the Large Load, each scheduled load 
level becomes part of the Firm Load Commitment on the applicable Service Date.
Except as expressly provided in this CRA, Eligible Customer’s failure to begin taking Firm 
Transmission Service to serve the Large Load Facilities, take Firm Transmission Service
corresponding to a scheduled load level, or maintain that level of Firm Transmission Service
does not reduce or defer the Firm Load Commitment or the Committed Revenue Contribution, or 
excuse Large Load Customer from any payment or Credit Support obligation under this CRA.
3.2
Post-Final PJM Agreement Update and Subsequent Modification
Within thirty (30) days after execution of the Final PJM Agreement, Transmission Owner shall 
update Exhibit A to reflect the Firm Transmission Service, load ramp, and Service Dates 
established through or consistent with the Final PJM Agreement. Transmission Owner shall also 
update the Applicable Firm Transmission Service Rate, Projected Committed Revenue 
Contributions, Projected Full Firm Transmission Service Benchmarks, Credit Support 
Requirement, the applicable schedules in Exhibits A and C, and the calculations under Exhibit B 
using the information then available.
The information reflected in the Final PJM Agreement shall control over the corresponding 
preliminary information included in Exhibit A at execution. If the Final PJM Agreement 
establishes less Firm Transmission Service than the Initial Load Commitment, the Firm Load 
Commitment shall be reduced accordingly. A reduction required by this paragraph shall not 
constitute a Partial Termination and shall not result in a Partial Termination Amount.
An update required by this Section shall become effective without further agreement of the 
Parties and shall not constitute an amendment to this CRA. Transmission Owner shall provide 
the updated Exhibits and reasonable supporting calculations to Eligible Customer and Large 
Load Customer.
After the update required by this Section, a further modification to the Firm Load Commitment 
or a Service Date shall become effective only if the Parties execute any amendment required 
under this CRA and the amendment receives any required PJM or FERC acceptance or approval. 
A customer-requested reduction remains subject to Article 9.
3.3
No Transmission Owner Obligation
Except as otherwise explicitly provided herein, nothing in this Agreement shall constitute an 
obligation on the part of Transmission Owner to provide any service to any Party or place into 
service any transmission facilities by any specific date or dates. 
ARTICLE 4
EFFECTIVE DATE AND TERM
4.1
Effective Date
Page 31

PDF page 197

This CRA will become effective on the later of : (1) the date  executed by all Parties, or (2) the 
date accepted or approved by FERC, if such acceptance or  approval is required, or (3) on such 
other date as FERC may establish in an order accepting or approving the CRA (the “Effective 
Date”).
4.2
Term
Unless terminated earlier in accordance with this CRA, the term of this CRA (the “Term”) shall
commence on the Effective Date and continue until the later of:  (i) the date that is at least ten 
(10) years after the first Service Date as specified in Exhibit A; and (ii) the date on which all 
outstanding obligations under this CRA have been satisfied. 
ARTICLE 5
REVENUE CONTRIBUTIONS AND SHORTFALL AMOUNT
5.1
Committed Revenue Contribution
For each Measurement Period during the Term, Transmission Owner  shall calculate the 
Committed Revenue Contribution in accordance with this Section and Exhibit B, using the 
applicable rates, billing determinants, and other information available in accordance with the 
PJM Tariff.  The Committed Revenue Contribution shall equal the Minimum Commitment 
Percentage multiplied by the Firm Transmission Service-related charges that would apply if 
Eligible Customer took Firm Transmission Service corresponding to the Firm Load Commitment 
applicable during the Measurement Period.
The calculation shall use:
(a) the Firm Load Commitment that applies during each Measurement Period;
(b) the Applicable Firm Transmission Service Rate and the generally applicable billing 
determinants under the PJM Tariff; and
(c) the portion of the Measurement Period during which each scheduled Firm Load 
Commitment amount and Applicable Firm Transmission Service Rate applies.
If more than one Firm Load Commitment amount or Applicable Firm Transmission Service Rate 
applies during a Measurement Period, Transmission Owner 
shall calculate separately the 
amount applicable to each portion of the Measurement Period and aggregate those amounts to 
determine the Committed Revenue Contribution for the applicable Measurement Period.
Eligible Customer shall be responsible for timely payment of charges for Firm Transmission 
Service in a given calendar year on a monthly basis in accordance with the PJM Tariff.
5.2
Actual Revenue Contribution
For each Measurement Period during the Term, Transmission Owner shall calculate the Actual 
Revenue Contribution attributable to Firm Transmission Service actually taken to serve the 
Large Load Facilities in accordance with Exhibit B.  To the extent that the Large Load Customer 
has made separate payments through a retail tariff or other retail mechanism that reflect the 
assignment of Firm Transmission Service or related costs to the Large Load Customer, such 
Page 32

PDF page 198

payments shall be taken into account in determining its Actual Revenue Contribution, insofar as 
doing so does not result in costs being shifted to other Eligible Customers taking service in the 
Transmission Owner’s Zone. To the extent that the applicable Firm Transmission Service 
methodology calculates charges using an assigned Network Service Peak Load contribution or 
another allocated billing determinant, the Actual Revenue Contribution shall be calculated using 
the billing determinant assigned to the Large Load Facilities for the applicable Measurement 
Period and the same categories of rates used to calculate the Committed Revenue Contribution.
5.3
Shortfall Amount
For each Measurement Period, the Shortfall Amount shall equal the amount, if any, by which the 
Committed Revenue Contribution exceeds the Actual Revenue Contribution in accordance with 
Exhibit B.
Large Load Customer shall pay each Shortfall Amount in accordance with Article 7.
5.4
Separate Measurement Periods
Each Measurement Period shall be calculated independently.
5.5
Commencement of Committed Revenue Contribution
The determination of the Committed Revenue Contribution and any corresponding Shortfall 
Amounts shall begin on the corresponding Service Date, as set forth in Exhibit A, regardless of 
whether: (i) Eligible Customer has begun taking the corresponding level of Firm Transmission 
Service; (ii) the amount of Firm Transmission Service taken by Eligible Customer corresponds to 
the load level scheduled to apply on that Service Date; or (iii) the Large Load Facilities are 
operating at a lower load level than the one scheduled to apply on that Service Date.
Notwithstanding the foregoing, if Eligible Customer cannot begin taking the applicable Firm 
Transmission Service on a Service Date solely because the necessary transmission facilities have 
not been  completed, and such delay was not  caused in whole or in part by Large Load 
Customer’s or Eligible Customer’s failure or lack of reasonable diligence in satisfying  its 
obligations under this CRA or under any other binding agreement, tariff, regulatory order, or 
other legal requirement, the Service Date and commencement of the corresponding Committed 
Revenue Contribution shall be extended on a day-for-day basis until the Firm Transmission 
Service becomes available.  Large Load Customer’s obligations include, without limitation (a) 
construction, testing, commissioning and readiness of any facilities being constructed by Large 
Load Customer, and (b) prompt and reasonable responses to Transmission Owner’s or 
Transmission Owners’ affiliate(s)’ requests for information, approvals, or other communications 
necessary for Transmission Owner’s or Transmission Owners’ affiliate(s)’ work.
5.6  
Access to Information
Eligible Customer shall provide, or authorize access to, the service, billing, settlement, and 
allocation information from PJM or any other entity reasonably necessary for Transmission 
Owner to calculate the Actual Revenue Contribution, Shortfall Amount, or any other calculation 
Page 33

PDF page 199

required under this Agreement.
ARTICLE 6
CREDIT SUPPORT
6.1
Obligation to Post and Maintain Credit Support
In accordance with Tariff, Part VIII, Subpart N, section 441(d), Large Load Customer shall, at its 
own expense, cause Credit Support equal to the Initial Credit Support Requirement identified in 
Exhibit C to be provided in favor of Transmission Owner not later than ten (10) days after the 
end of the negotiation period specified in Tariff, Part VIII, Subpart N, section 441(c).
If Large Load Customer fails to provide the required Credit Support within that period, the 
consequences specified in Tariff, Part VIII, Subpart N, section 441(d) shall apply.
Within five (5) Business Days after receipt of the post-PJM recalculation required under Section 
3.2, Large Load Customer shall cause the Credit Support to be increased, reduced, amended, or 
replaced as necessary to equal the recalculated Credit Support Requirement.
The Credit Support shall secure Large Load Customer’s payment and other financial obligations 
under this CRA and shall at all times equal or exceed the Credit Support Requirement set forth in 
Exhibit C, subject to any reduction or treatment of prior draws expressly provided in this CRA.
The Credit Support Requirement shall be based on 100% of the Projected Full Firm 
Transmission Service Benchmarks for the applicable remaining Measurement Periods and shall 
not be reduced by the Minimum Commitment Percentage.
Large Load Customer shall cause the Credit Support to be maintained throughout the Term and 
thereafter until:
(a) all Shortfall Amounts and other amounts due under this CRA have been paid;
(b) the final reconciliation required under this CRA has been completed; and
(c) Transmission Owner has no remaining right to draw on the Credit Support under this 
CRA.
6.2 
Form of Credit Support 
Credit Support shall be a Letter of Credit in the form specified in Exhibit C and related 
attachments to Exhibit C.  
6.3
Replacement of Credit Support
Large Load Customer shall cause compliant replacement Credit Support to be provided within
five (5) Business Days after notice from Transmission Owner if:  (i) the issuer ceases to satisfy 
the requirements of Exhibit C; (ii) the Credit Support ceases to satisfy this Article 6; (iii) the 
Credit Support will expire or terminate before Large Load Customer’s obligation to maintain 
Credit Support ends; or (iv) the issuer gives notice of nonrenewal.
Page 34

PDF page 200

Replacement Credit Support provided under this Section shall be in an amount equal to the then-
applicable Credit Support Requirement, as  determined under Section 6.5 and Exhibit C as of the 
replacement date to reflect any completed Measurement Period that has been excluded from the 
Credit Support Requirement in accordance with Section 6.5, less the amount of any cash security 
then held by Transmission Owner and legally available to secure the same obligations.
6.4
Preservation Draw
If Large Load Customer fails to cause timely replacement Credit Support to be provided under 
Section 6.3, Transmission Owner may draw the lesser of: (i) the full amount then available under 
the existing Credit Support; and (ii) the then-applicable Credit Support Requirement, less any 
cash security then held by Transmission Owner and legally available to secure the same 
obligations. Transmission Owner may hold the proceeds as cash security for Large Load 
Customer’s obligations under this CRA.
A preservation draw does not constitute payment of an obligation unless and until Transmission 
Owner applies the proceeds to an amount due under this CRA.
Transmission Owner shall release cash security held under this Section after Large Load 
Customer causes compliant replacement Credit Support to be provided, except to the extent the 
cash has been applied to an amount due.
6.5
Adjustment of Credit Support Requirement
The Credit Support Requirement for each applicable period shall be calculated in accordance 
with Exhibit C.
Transmission Owner shall also recalculate the Credit Support Requirement following the update 
required under Section 3.2. That recalculation shall replace the Initial Credit Support 
Requirement and shall reflect the Firm Load Commitment, Service Dates, Applicable Firm 
Transmission Service Rate, Projected Full Firm Transmission Service Benchmarks, and other 
information established following the Final PJM Agreement.
Transmission Owner shall recalculate the Credit Support Requirement after completion of each 
Measurement Period and upon any other recalculation event specified in Exhibit C. The 
recalculated Credit Support Requirement shall equal the aggregate Projected Full Firm 
Transmission Service Benchmarks for the Measurement Periods remaining in the Term, 
including any incomplete portion of the applicable Measurement Period. A completed 
Measurement Period shall be excluded from the Credit Support Requirement only after: (i) the 
Committed Revenue Contribution, Actual Revenue Contribution, and any resulting Shortfall 
Amount for that Measurement Period have been finally calculated; and (ii) Large Load Customer 
has paid all amounts due for that Measurement Period.
If the Credit Support Requirement increases, Large Load Customer shall cause the Credit 
Support to be increased to the recalculated Credit Support Requirement within five (5) Business 
Days after receipt of the calculation.
Page 35

PDF page 201

If the Credit Support Requirement decreases, Transmission Owner shall authorize a 
corresponding reduction within five (5) Business Days of a request by the financial institution 
issuing the Credit Support for such authorization, provided that no payment default or other 
Event of Default exists and the remaining Credit Support, together with any cash security held by 
Transmission Owner, will equal or exceed the adjusted Credit Support Requirement.
Actual Revenue Contributions for a completed Measurement Period shall be used to determine 
the Shortfall Amount for that completed Measurement Period but shall not reduce the Projected 
Full Firm Transmission Service Benchmarks used to calculate the Credit Support Requirement 
for future Measurement Periods.
6.6
Draws for Unpaid Amounts
Except for a preservation draw under Section 6.4, Transmission Owner may draw on Credit 
Support only after:  (i) Transmission Owner has issued an invoice identifying an amount due 
under this CRA and the basis for that amount; and  (ii) Large Load Customer has failed to pay 
the invoiced amount within the payment period specified in Article 7.
A draw shall not exceed the amount due and unpaid.
Transmission Owner shall apply the proceeds of a draw to the unpaid amount for which the draw 
was made. Proceeds applied to a Shortfall Amount shall be credited in accordance with Section 
7.6, and proceeds applied to an Early Termination Amount or Partial Termination Amount shall 
be applied and credited in accordance with Section 9.12.  Large Load Customer’s payment 
default shall be cured to the extent Transmission Owner receives and applies proceeds sufficient 
to satisfy the unpaid amount.
6.7
Replenishment
Following a draw applied to satisfy an unpaid amount,  Large Load Customer shall cause the 
Credit Support to be restored to the applicable Credit Support Requirement within five (5) 
Business Days after notice from Transmission Owner.
6.8
Release of Credit Support
Transmission Owner shall release the remaining Credit Support within ninety (90) days after the 
latest of:  (i) expiration or termination of the Term; (ii) completion of all calculations, invoices, 
and reconciliations required under this CRA; (iii) payment of all undisputed amounts determined 
to be due under this CRA; or (iv) resolution of any pending dispute that could result in an 
additional amount payable by Large Load Customer .
Transmission Owner shall provide release or cancellation documentation relating to Credit 
Support to Large Load Customer, with a copy to Eligible Customer.
ARTICLE 7
Page 36

PDF page 202

INVOICING AND PAYMENT
7.1
Determination and Invoice
After the end of each Measurement Period, Transmission Owner shall calculate the Committed 
Revenue Contribution, Actual Revenue Contribution, and resulting Shortfall Amount in 
accordance with Article 5 and Exhibit B.
If a Shortfall Amount exists, Transmission Owner shall inform the other Parties and issue an 
invoice to Large Load Customer for the Shortfall Amount within sixty (60)  days after the end of 
the applicable Measurement Period.  Transmission Owner shall provide Eligible Customer with a 
copy of the invoice.
7.2
Payment
Large Load Customer shall timely pay all amounts invoiced and due under this CRA by no later 
than thirty (30) days after the date of receipt of the applicable invoice.  Any payment made after 
thirty (30) days, including any draw made by a Transmission Owner pursuant to Sections 6.6 and 
7.3 below shall include interest at the FERC rate set forth in 18 CFR Section 35.19.
7.3
Draw on Credit Support
If Large Load Customer fails to timely pay an invoiced amount, Transmission Owner may draw 
on the Credit Support for the unpaid amount in accordance with Section 6.6.
7.4
Review of Supporting Documentation
Upon Large Load Customer’s timely request, Transmission Owner and  if applicable, Eligible 
Customer, shall provide documentation reasonably necessary to enable Large Load Customer to
verify the accuracy of an invoice, subject to applicable confidentiality requirements.  For 
purposes of this section, a request shall be considered timely if made no more than five (5) 
Business Days after the date of receipt of the applicable invoice.  
Eligible Customer shall provide or authorize access to any service, billing, settlement, or 
allocation information reasonably necessary to support that review.
A request under this section shall not act to defer or extend the date on which payment is due 
under Section 7.2.
7.5
Disputed Amounts
Large Load Customer shall timely pay each invoiced amount notwithstanding any dispute, and 
Transmission Owner’s right to draw on Credit Support shall not be suspended by the dispute. If 
the final resolution determines that Large Load Customer paid, or Transmission Owner drew, 
more than the amount properly due, Transmission Owner shall promptly return the excess 
amount.  Any dispute must be made by no later than the date payment is due and conform to the 
Page 37

PDF page 203

requirements set forth in Section 15.1 below.
7.6
Crediting of Shortfall Amounts
All Shortfall Amounts collected by Transmission Owner shall be credited against the 
Transmission Revenue Requirement of the Transmission Owner for the Transmission  Zone in 
which the Eligible Customer is taking Firm Transmission Service.  Transmission Owner shall 
account for and credit all amounts received under this CRA in accordance with this Section 7.6, 
Section 9.12, as applicable, the PJM Tariff, and its applicable FERC-jurisdictional rate.  
Transmission Owner’s calculation, collection, accounting, and crediting of Shortfall Amounts 
shall be reflected in, and remain subject to review under, Transmission Owner’s applicable 
FERC-jurisdictional formula rate and related protocols.
ARTICLE 8
DEFAULT AND REMEDIES
8.1
Events of Default
Each of the following constitutes an “Event of Default” by the applicable Party:
(a) failure by Large Load Customer to cause the initial Credit Support to be timely 
provided in the amount and form required under this CRA;
(b) failure by Large Load Customer to cause to be timely provided replacement or 
additional Credit Support required under Article 6;
(c) failure by Large Load Customer to cause Credit Support to be replenished when 
required under Section 6.7;
(d) a material misrepresentation by a Party concerning the Firm Load Commitment, 
Actual Revenue Contribution, Credit Support, or another material matter under this CRA;
(e) assignment or attempted assignment of this CRA by a Party in violation of Article 10;
(f) repudiation of this CRA by a Party; 
(g) failure by Eligible Customer to take any PJM Tariff action expressly required of 
Eligible Customer under this CRA or a default by Eligible Customer under any PJM 
agreement relating to the provision of Firm Transmission Service; or
(h) failure by Eligible Customer or Large Load Customer to take an action expressly 
required under this CRA to request, pursue, or complete the applicable PJM process; or
(i) a default by Large Load Customer under any agreement with Transmission Owner or 
its Affiliates relating to the Large Load Facilities, including any failure to comply with 
any retail service tariffs, retail agreements, or other retail obligations that would prevent 
the Large Load Customer from meeting its obligations under this CRA;
(j) the bankruptcy or insolvency of Large Load Customer; or
(k) any other material breach by a Party  that remains uncured after the applicable period 
provided in Section 8.2.
8.2
Notice and Cure
Except as otherwise expressly provided in this CRA, Transmission Owner shall provide the 
Defaulting Party with written notice of an Event of Default describing the default in reasonable 
detail.
Page 38

PDF page 204

The Defaulting Party  shall have: (i) five (5) Business Days after receipt of notice to cure a 
Credit Support default; and (ii) fifteen  (15) days after receipt of notice to cure any other curable 
Event of Default.
8.3
Remedies
Following an Event of Default that has not been timely cured, the non-Defaulting Party or Parties  
may, in their sole discretion:
(a) if Transmission Owner is a non-Defaulting Party, draw on Credit Support in 
accordance with this CRA;
(b) recover any amount due and unpaid under this CRA;
(c) require specific performance of Large Load Customer’s obligation to cause Credit 
Support to be provided or maintained;
(d) exercise any right or remedy available under the PJM Tariff to the extent applicable to 
that Party;
(e) terminate this CRA only as expressly permitted under Article 9; and
(f) exercise any other right or remedy available under applicable law.
Transmission Owner shall credit all payments and Credit Support proceeds against the obligation 
for which they were received and shall not obtain duplicative recovery of the same amount.
8.4
Effect of Credit Support Draw
Receipt and application of Credit Support proceeds sufficient to satisfy an unpaid amount shall 
cure the applicable payment default to the extent of the proceeds received and applied.
ARTICLE 9
EARLY AND PARTIAL TERMINATION
9.1
Termination or Reduction by Large Load Customer; Withdrawal from PJM 
Process
Before execution of the Final PJM Agreement, Eligible Customer’s withdrawal or abandonment 
of the request for Firm Transmission Service from the applicable PJM process on behalf of Large 
Load Customer, or refusal to execute the Final PJM Agreement shall constitute an early 
termination of this CRA by Large Load Customer.  Large Load Customer shall pay the Early 
Termination Amount calculated under Section 9.7 and Exhibit D. Termination under this 
paragraph shall become effective upon the applicable withdrawal, abandonment, or refusal and 
shall not be subject to the 120-day notice period below.
After execution of the Final PJM Agreement, Large Load Customer may terminate this CRA 
before expiration of the Term by providing Transmission Owner and Eligible Customer with at 
least 120 days’ prior written notice. Notwithstanding the foregoing, termination shall not become 
effective unless and until (a) the Large Load Customer has paid in full the applicable Early 
Termination Amount or Partial Termination Amount, as determined pursuant to this CRA, or (b) 
Page 39

PDF page 205

if such amount remains unpaid, the Transmission Owner has drawn on the Credit Support and 
recovered the full amount of such unpaid Early Termination Amount or Partial Termination 
Amount.  
Large Load Customer shall pay the Early Termination Amount calculated under Section 9.7 and 
Exhibit D. 
Large Load Customer’s  obligation to pay the Early Termination Amount shall survive 
termination and remain secured by Credit Support until paid in full.
9.2
Partial Termination
Before execution of the Final PJM Agreement, a reduction by Large Load Customer or Eligible 
Customer in the amount of Firm Transmission Service requested through the PJM process shall 
constitute a Partial Termination.
Large Load Customer may permanently reduce a specified portion of the Firm Load 
Commitment by providing Transmission Owner and Eligible Customer with at least 120 days’ 
prior written notice and paying the Partial Termination Amount calculated under Section 9.8 and 
Exhibit D.
A Partial Termination shall become effective only after:  (i) PJM has approved, directed, or 
otherwise recognized the reduction to the extent required under the PJM Tariff; (ii) the Parties 
have executed an amendment to Exhibit A; and (iii) the amendment has become effective under 
applicable FERC requirements.
If the Large Load Facilities have not achieved the state of readiness necessary to take Firm 
Transmission Service corresponding to the applicable Firm Load Commitment by 120 days after 
each Service Date, such occurrence will constitute a Partial Termination.
9.3
Project Abandonment or Cessation
Each Party shall notify the other Parties within five (5) Business Days after becoming aware 
that:
(a) the Large Load Customer has determined that it will not construct or complete the 
Large Load Facilities or proceed with the applicable request for Firm Transmission 
Service;
(b) the Large Load Facilities have not achieved the state of readiness necessary to take 
Firm Transmission Service by 120 days after the initial Service Date;
(c) the Large Load Customer intends to permanently cease operations at the Large Load 
Facilities; or
(d) Eligible Customer intends to permanently cease taking Firm Transmission Service to 
serve the Large Load Facilities.
Upon notice or occurrence of an event described in this Section, Transmission Owner may 
terminate this CRA upon thirty (30) days’ written notice to the other Parties, and  Large Load 
Customer  shall pay the Early Termination Amount. Large Load Customer’s obligation to pay 
Page 40

PDF page 206

the Early Termination Amount shall survive termination and remain secured by Credit Support 
until paid in full.
9.4
Termination for Default
Transmission Owner may terminate this CRA upon written notice to other Parties if a Party:
(a) commits an Event of Default that is not capable of cure; or
(b) fails to cure an Event of Default within the applicable period under Article 8.
Upon termination, Large Load Customer shall pay:
(a) all Shortfall Amounts and other amounts accrued through the termination date;
(b) the Early Termination Amount; and
(c) any other amount due under this CRA, subject to the prohibition against duplicative 
recovery.
Transmission Owner may apply Credit Support or cash security to those amounts in accordance 
with Articles 6, 7 and 9.
9.5
Termination by Mutual Agreement
The Parties may terminate this CRA by mutual written agreement, subject to applicable FERC 
requirements.
Any such agreement shall specify the treatment of the Early Termination Amount, any 
outstanding Shortfall Amounts, and the remaining Credit Support provided by Large Load 
Customer.
9.6
Termination Due to Transmission Facility-Related Delay  
If any extension of a Service Date or Committed Revenue Contribution under the second 
paragraph of Section 5.5 results in a forecasted or actual extension of [Insert number of months] 
months or more to either the first  Service Date or any subsequent Service Date, Large Load 
Customer may, at its option, either (1) terminate this CRA; or (2) accept the timing and resulting 
adjustment to the applicable Service Date(s).
If Large Load Customer elects to terminate this CRA pursuant to this Section 9.6, Large Load 
Customer shall be responsible for paying an Early Termination Amount calculated pursuant to  
Exhibit D.  However, for purposes of determining the Applicable Termination Percentage under 
Exhibit D the number of days in any forecasted or actual extension to the Service Date or 
Committed Revenue Contribution shall not be counted.  
To invoke this termination right, Large Load Customer must provide written notice to 
Transmission Owner and Eligible Customer within 60 days of receipt of notice that any 
forecasted or actual extension will equal or exceed [Insert number of months] months.  
Moreover, Large Load Customer will not be permitted to invoke this termination right if the 
delay is caused in whole or part by Large Load Customer’s failure or lack of reasonable 
Page 41

PDF page 207

diligence in meeting its obligations under this Agreement or any other binding agreement, tariff, 
regulatory order or other legal requirement, as set forth in Section 5.5.
9.7
Early Termination Amount
The “Early Termination Amount” shall be calculated in accordance with Exhibit D. 
9.8
Partial Termination Amount
The “Partial Termination Amount” shall be calculated in accordance with Exhibit D.  After the 
Partial Termination becomes effective, the Committed Revenue Contribution and Credit Support 
Requirement shall be calculated using the remaining Firm Load Commitment, provided that the 
Credit Support Requirement shall continue to be based on 100% of the Projected Full Firm 
Transmission Service Benchmarks corresponding to that remaining Firm Load Commitment.
9.9
Early Termination Offset Amount
If the Early Termination Offset Amount is quantifiable when Transmission Owner issues the 
termination invoice, it shall be included as an Applicable Credit.
If the offset becomes quantifiable afterward, Transmission Owner shall reflect it in a subsequent 
reconciliation and promptly return any resulting excess payment to Large Load Customer.
Nothing in this Section requires Transmission Owner to market the Point of Delivery, solicit 
replacement load, modify its transmission planning or service processes, or enter into a service 
arrangement with another Person.
9.10
Invoice and Payment
Transmission Owner shall promptly invoice  Large Load Customer for the Early Termination 
Amount or Partial Termination Amount and provide reasonable substantiation of the calculation. 
For the avoidance of doubt, in the event that the Large Load Customer fails to timely pay an 
invoice for the Early Termination Amount or Partial Termination Amount, the Transmission 
Owner shall be permitted to draw on the Credit Support for the unpaid amount.  
9.11
Effect of Termination
Any full termination of this CRA for any reason shall result in (i) before execution of the Final 
PJM Agreement, withdrawal or cancellation of the applicable request for Firm Transmission 
Service; and (ii) after execution of the Final PJM Agreement, cancellation of the Firm 
Transmission Service taken by Eligible Customer on behalf of Large Load Customer and the 
related Transmission Service Agreement, except where FERC has accepted a replacement or 
substitute agreement that contains terms reasonably comparable to this CRA pursuant to PJM 
Tariff, Part VIII, Section 438(b).
A Partial Termination shall result in the corresponding reduction of the request for Firm 
Transmission Service or the Firm Transmission Service, as applicable.
Page 42

PDF page 208

For avoidance of doubt, termination of this CRA and related cancellation of Firm Transmission 
Service shall not prohibit Large Load Customer from seeking Firm Transmission Service in the 
future.
9.12
Crediting of Termination Amount
If the effective date of an Early Termination or Partial Termination occurs prior to the first 
Service Date and the Large Load Customer is required to pay an Early Termination Amount or 
Partial Termination Amount, as applicable, such amount shall first be applied to the Project 
Development Costs as of the effective date of such termination in accordance with PJM Tariff, 
Part VIII, Subpart N, section 441(e).  Any remaining amounts from the applicable Termination 
Amount shall be credited to the Transmission Owner's Transmission Revenue Requirement for 
the Transmission Zone in which the Eligible Customer would have taken Transmission Service. 
For the avoidance of doubt, if Transmission Owner allocates any of the applicable Termination 
Amount to the Project Development Costs, such amount shall not be recovered in Transmission 
rates.  
 
If the effective date of an Early Termination or Partial Termination occurs on or after the first 
Service Date and the Large Load Customer is required to pay an Early Termination Amount or 
Partial Termination Amount, as applicable, such amount shall be credited to the Transmission 
Owner's Transmission Revenue Requirement for the Transmission Zone in which the Eligible 
Customer would have taken Firm Transmission Service. 
ARTICLE 10
ASSIGNMENT
10.1
Assignment by Eligible Customer
Eligible Customer may not assign or transfer this CRA, or any right or obligation arising under 
this CRA, in whole or in part, without the prior written consent of Transmission Owner and 
Large Load Customer, which consent shall not be unreasonably withheld, conditioned, or 
delayed.
Notwithstanding the foregoing, Eligible Customer may assign its rights and obligations under 
this CRA to an Affiliate without Transmission Owner’s prior written consent, if:
(a) Eligible Customer provides the other Parties with prior written notice of the proposed 
assignment;
(b) the proposed assignee is an Eligible Customer under the PJM Tariff and is authorized 
to take Firm Transmission Service on behalf of the Large Load Customer;
(c) the proposed assignee assumes in writing all obligations of Eligible Customer under 
this CRA;
(d) the assignment has received any acceptance, approval, or recognition required from 
PJM or FERC; and
(e) all disputes between Transmission Owner and existing Eligible Customer as to 
invoice outstanding have been reconciled.
Page 43

PDF page 209

An assignment by Eligible Customer shall not change Large Load Customer’s status or release, 
reduce, or otherwise modify Large Load Customer’s obligations under this CRA.
An assignment shall not become effective until all applicable requirements of this Section have 
been satisfied.
10.2
Effect of Assignment
Except as expressly provided in a written assignment agreement accepted by Transmission 
Owner and Large Load Customer, an assignment shall not release the assigning Eligible 
Customer from: (i) any breach or Event of Default occurring before the effective date of 
assignment; (ii) any obligation arising from information, service, or conduct occurring before the 
effective date of assignment but calculated or invoiced afterward; or (iii) any obligation that 
expressly survives assignment.
After the effective date of a permitted assignment, the assignee shall be treated as the Eligible 
Customer for purposes of this CRA and shall perform all obligations
assigned to Eligible 
Customer under this CRA on and after the effective date of assignment.
10.3
Assignment by Large Load Customer
Large Load Customer may not assign or transfer this CRA or any right or obligation arising 
under this CRA, in whole or in part, without the prior written consent of Transmission Owner 
and Eligible Customer, which consent shall not be unreasonably withheld, conditioned, or 
delayed.
An assignment by Large Load Customer shall not become effective unless:
(a) the proposed assignee assumes in writing all obligations of Large Load Customer 
under this CRA;
(b) compliant replacement Credit Support is provided that directly secures the proposed 
assignee’s obligations under this CRA;
(c) the assignment is documented through a written amendment or assignment executed 
by the applicable Parties;
(d) the assignment has received any acceptance, approval, or recognition required from 
PJM or FERC; and
(e) All disputes between Transmission Owner and existing Large Load Customer as to 
invoice outstanding have been reconciled.
A transfer of ownership, operation, leasehold rights, or control of the Large Load Facilities does 
not, by itself, assign this CRA or release Large Load Customer from its obligations under this 
CRA.
10.4
Assignment by Transmission Owner
Transmission Owner may assign this CRA, in whole or in part, without the other Parties’ 
consent:  (i) to a successor to all or substantially all of the transmission assets or obligations 
relevant to this CRA; (ii) in connection with a merger, consolidation, reorganization, or other 
corporate transaction; (iii) to an Affiliate that assumes Transmission Owner’s obligations under 
Page 44

PDF page 210

this CRA; or (iv) as required or authorized by the PJM Tariff, FERC, or another governmental 
authority with jurisdiction.
Transmission Owner shall provide the other Parties with written notice of the assignment.
Any other assignment by Transmission Owner requires the prior written consent of the other 
Parties, which consent shall not be unreasonably withheld, conditioned, or delayed.
ARTICLE 11
REGULATORY PROVISIONS
11.1
Regulatory Effectiveness
This CRA shall be submitted, reported, designated, posted, or filed only to the extent required by 
the PJM Tariff, a FERC order, regulation, or applicable law.
Completion of project-specific information, dates, amounts, percentages, schedules, and other 
elections expressly contemplated by the FERC-accepted form of CRA shall not constitute a 
nonconforming term or condition.
Updates to Exhibits A and C and calculations under Exhibit B required under Section 3.2 are 
expressly contemplated by this CRA and shall not constitute nonconforming terms or 
amendments, except to the extent a further filing with or acceptance by FERC is required.
11.2
Required FERC Filing
If this CRA is required to be filed with FERC under the PJM Tariff, a FERC order, or applicable 
law, Transmission Owner shall submit this CRA for acceptance under Section 205 of the Federal 
Power Act in accordance with PJM Tariff, Part VIII, Subpart N.
Transmission Owner shall take the lead in preparing and prosecuting the filing and shall use 
reasonable efforts to obtain FERC’s acceptance of this CRA.
Each Party shall reasonably cooperate in connection with the filing and refrain from taking a 
position inconsistent with the acceptance of this CRA, except as required by applicable law or 
expressly permitted under this CRA.
Each Party shall bear its own costs incurred in connection with the filing unless the Parties 
otherwise agree in writing.
11.3
Relationship to Other Tariffs and Agreements
Nothing in this CRA shall be construed to grant, provide, guarantee, or otherwise convey 
transmission service under the PJM Tariff, distribution or retail service under state-regulated 
tariffs or agreements, or any other service or rate, term or condition of such service, except as 
expressly provided herein. 
Page 45

PDF page 211

Nothing in this CRA limits any obligation under the PJM Tariff or another applicable agreement 
to pay study costs, directly assigned facility costs, Network Upgrade costs, or other costs 
associated with transmission service.
ARTICLE 12
FORCE MAJEURE
12.1
Definition and Scope of Force Majeure
“Force Majeure” means an event or circumstance that:
(a) physically and directly impacts the Large Load Facilities, new transmission facilities, 
or modifications to existing transmission facilities, and/or 
(b) prevents the Affected Party from performing its obligations under this CRA, 
which event or circumstance (i) could not have been  reasonably anticipated as of the Effective 
Date and (ii) which is not within the reasonable control of, or the result of negligence or 
misconduct by, the Affected Party, and (iii) which the Affected Party is unable to overcome or 
avoid or cause to be avoided, by the exercise of reasonable care.  Subject to meeting the 
requirements of the prior sentence, Force Majeure events shall include, but not be limited to, acts 
of God; fire; flood; earthquake; war; explosions; labor disputes; lightning; hurricanes; tornadoes; 
pandemics or epidemics; riots; or acts of terrorism that affect one or more Parties.  With respect 
to a Party’s obligation to make payments hereunder, Force Majeure will be only an event or act 
that on any day disables the banking system through which a Party makes such payments.  
Nothing herein shall be construed so as to require a Party to settle any strike or labor dispute in 
which it may be involved.  Economic hardship of any Party shall not constitute a Force Majeure 
under this CRA, even if that economic hardship is caused by an event or condition that would 
have been a Force Majeure event if it has physically and directly impacted the Large Load 
Facilities, new transmission facilities, or modifications to existing transmission facilities.
No event affecting only the Large Load Customer, the Large Load Facilities, or the amount of 
Firm Transmission Service taken to serve the Large Load Facilities shall constitute Force 
Majeure with respect to Large Load Customer’s payment or Credit Support obligations under 
this CRA.
The Party claiming Force Majeure bears the burden of establishing that the event satisfies every 
requirement of this Section.
If a Party is rendered unable, wholly or in part, by Force Majeure to carry out its obligations with 
respect to this CRA (the “Affected Party”), then the obligations of the Affected Party will, to the 
extent they are affected by such Force Majeure event, be suspended during the period of time 
that the Force Majeure event renders the Affected Party unable, wholly or in part, to carry out its 
obligations.  The Affected Party will not be liable for breach of this CRA due to a Force Majeure 
event nor shall the Affected Party be liable to the other Parties for, or on account of, any loss, 
damage, injury, or expense resulting from, or arising out of such Force Majeure event.  The 
Affected Party must give written notice and full particulars of such Force Majeure event as soon 
Page 46

PDF page 212

as practical after the occurrence of the Force Majeure event.  If a Force Majeure event continues 
for over 180 days in the aggregate during any 12 month period, the Parties will meet and in good 
faith attempt to renegotiate the terms and conditions of this CRA to address and account for the 
Force Majeure event.  If the Parties are thereafter unable to mutually agree in writing on an 
amendment to this CRA to address issues arising out of the Force Majeure event, Transmission 
Owner or Large Load Customer may terminate this CRA upon ten (10) days’ written notice to 
the other Parties, subject to Section 12.2, Article 9, and any obligations that accrued or survive 
under this CRA.
12.2
Termination Due to Force Majeure   
In the event that Large Load Customer terminates this Agreement pursuant to Section 12, the 
Large Load Customer shall remain obligated to pay the Early Termination Amount.  However, if 
the Transmission Owner terminates this Agreement pursuant to Section 12, Large Load 
Customer shall not be required to pay the Early Termination Amount.
12.3
Effect of Force Majeure
If a Party is prevented by Force Majeure from performing an obligation under this CRA, that 
obligation shall be suspended only:  (i) to the extent performance is physically impossible 
because of the Force Majeure; (ii) for the period during which performance remains physically 
impossible; and (iii) while the affected Party complies with Section 12.4.
The affected Party shall not be in breach of this CRA solely because it fails to perform an 
obligation properly suspended under this Section.
Force Majeure does not:
(a) excuse or delay an obligation to pay an amount due under this CRA, except solely to 
the extent expressly provided in Section 12.1;
(b) excuse or delay Large Load Customer’s obligation to cause Credit Support to be 
provided, maintained, increased, renewed, replaced, or replenished;
(c) except for an extension of a Service Date expressly permitted under Section 5.5, 
reduce, defer, or otherwise modify the Firm Load Commitment, any Service Date, or the 
Minimum Commitment Percentage;
(d) reduce or defer the calculation of the Committed Revenue Contribution, Actual 
Revenue Contribution, Shortfall Amount, Early Termination Amount, or Partial 
Termination Amount;
(e) excuse Eligible Customer’s failure to take Firm Transmission Service corresponding 
to the Firm Load Commitment;
(f) require Transmission Owner to release or reduce Credit Support;
(g) prevent Transmission Owner from issuing an invoice, completing a calculation or 
reconciliation, or drawing on Credit Support in accordance with this CRA; 
(h) excuse any obligation that arose before the Force Majeure began; or
(i) affect the application of Article 9 to any abandonment, permanent cessation, 
permanent reduction, or termination associated with the Force Majeure.
For the avoidance of doubt, a Force Majeure affecting the Large Load Customer, the Large Load 
Page 47

PDF page 213

Facilities, or the amount of Firm Transmission Service taken to serve the Large Load Facilities 
shall not reduce, defer, or otherwise modify Large Load Customer’s payment or Credit Support 
obligations under this CRA. If circumstances associated with a Force Majeure result in 
abandonment, permanent cessation, permanent reduction, or termination, Article 9 shall govern 
the availability, effectiveness, and financial consequences of that abandonment, cessation, 
reduction, or termination.
12.4
Notice
A Party claiming Force Majeure shall provide the other Parties with written notice as soon as 
reasonably practicable after becoming aware of the event.
Failure to provide timely notice shall not prevent an event from qualifying as Force Majeure, but 
the affected Party shall not be excused from performance to the extent the delay in notice 
materially prejudices  another Party.
ARTICLE 13
REPRESENTATIONS AND WARRANTIES
13.1
Mutual Representations and Warranties
Each Party represents and warrants to the other Parties, as of the date it executes this CRA and as 
of the Effective Date, that:
(a) it is duly organized, validly existing, and in good standing under the laws of its 
jurisdiction of organization, to the extent such concepts apply;
(b) it has the power and authority to execute, deliver, and perform this CRA;
(c) its execution by the Parties, delivery, and performance of this CRA have been duly 
authorized by all necessary organizational action;
(d) the individual executing this CRA on its behalf has authority to bind it;
(e) this CRA constitutes its legal, valid, and binding obligation, enforceable against it in 
accordance with its terms, subject to applicable bankruptcy, insolvency, reorganization, 
moratorium, and similar laws affecting creditors’ rights generally and to general 
principles of equity;
(f) its execution by the Parties, delivery, and performance of this CRA do not violate its 
organizational documents, applicable law, or any agreement binding on it in a manner 
that would materially impair its performance under this CRA; and
(g) except for any acceptance, approval, filing, or other action expressly contemplated by 
this CRA, the PJM Tariff, or applicable law, no consent or approval is required for its 
execution by the Parties, delivery, or performance of this CRA that has not been obtained 
or will not be obtained when required.
13.2
Eligible Customer Representations and Warranties
Eligible Customer represents and warrants to the other Parties, as of the date it executes this 
CRA and as of the Effective Date, that:
(a) it is an Eligible Customer under the PJM Tariff;
(b) it is authorized under the PJM Tariff and applicable law to take Firm Transmission 
Page 48

PDF page 214

Service on behalf of the Large Load Customer to serve the Large Load Facilities;
(c) it has obtained, or will obtain when required, all authority, consent, and information 
necessary to perform its obligations under this CRA;
(d) all information provided by or on behalf of Eligible Customer for purposes of 
calculating the Actual Revenue Contribution, Shortfall Amount, Credit Support 
Requirement, Early Termination Amount, or Partial Termination Amount is and shall be 
materially accurate and complete;
(e) it has not relied on any representation or warranty by Transmission Owner concerning 
whether the Large Load Facilities shall be constructed, completed, achieve commercial 
operation, operate at any load level, or remain economically viable;
(f) it will provide or authorize access to the service, billing, settlement, and allocation 
information reasonably necessary to administer this CRA;
(g) Eligible Customer’s obligations under this CRA are limited to the transmission-
service, information-sharing, cooperation, and administrative obligations expressly 
assigned to Eligible Customer and do not include Large Load Customer’s payment or 
Credit Support obligations; 
(h) Eligible Customer shall timely perform its expressly assigned obligations 
notwithstanding any dispute with Large Load Customer; 
(i) it has agreed to request and pursue the Firm Transmission Service initially identified 
in Exhibit A on behalf of Large Load Customer through the applicable PJM process; and
(j) neither the failure of the Large Load Customer to perform nor a dispute between 
Eligible Customer and the Large Load Customer will excuse Eligible Customer’s 
performance under this CRA.
13.3
Large Load Customer Representations and Warranties
Large Load Customer represents and warrants to the other Parties, as of the date it executes this 
CRA and as of the Effective Date, that:
(a) it owns, operates, leases, or otherwise controls the Large Load Facilities;
(b) the information it provides concerning the Large Load Facilities, Firm Load
Commitment, Service Dates, load ramp, construction status, anticipated operations, and 
cessation or reduction of operations, and any other information required by or necessary 
to administer this CRA is and shall be materially accurate and complete;
(c) it has not relied on any representation or warranty by Transmission Owner concerning 
whether the Large Load Facilities will be constructed, completed, achieve commercial 
operation, operate at any load level, or remain economically viable; 
(d) its payment and Credit Support obligations under this CRA are direct obligations to 
Transmission Owner and do not depend on the performance of Eligible Customer or any 
other Person; 
(e) Credit Support provided under Article 6 directly secures Large Load Customer’s 
obligations under this CRA and, to Large Load Customer’s knowledge, is valid and 
enforceable in accordance with its terms; 
(f) it has designated Eligible Customer to request and take Firm Transmission Service on 
its behalf and has obtained Eligible Customer’s agreement to participate in the applicable 
PJM process; and
Page 49

PDF page 215

(g) Large Load Customer has not created or permitted any undisclosed lien, competing 
claim, restriction, or other interest that would materially impair Transmission Owner’s 
rights in the Credit Support.
13.4
Transmission Owner Representations and Warranties
Transmission Owner represents and warrants to the other Parties, as of the date it executes this 
CRA and as of the Effective Date, that:  (i) it is a PJM Transmission Owner; (ii) it is authorized 
to enter into this CRA and receive amounts and Credit Support payable or provided under this 
CRA, subject to the PJM Tariff and applicable FERC requirements.
ARTICLE 14
CONFIDENTIALITY
14.1
Confidential Information
For purposes of this Article, “Confidential Information” means nonpublic commercial, financial, 
operational, technical, customer-specific, or proprietary information disclosed by or on behalf of 
one Party to  another Party in connection with this CRA, whether disclosed orally, electronically, 
or in writing, including nonpublic information concerning:
(a) the Large Load Customer or the Large Load Facilities;
(b) the Firm Load Commitment, Service Dates, anticipated or actual load, or operating 
status of the Large Load Facilities;
(c) Firm Transmission Service taken to serve the Large Load Facilities;
(d) the calculation of the Actual Revenue Contribution, Shortfall Amount, Credit Support 
Requirement, Early Termination Amount, or Partial Termination Amount;
(e) Credit Support, the financial condition of Large Load Customer , and communications 
with an issuer; and
(f) any invoice, supporting documentation, or other information exchanged in 
administering this CRA.
Information shall constitute Confidential Information only if:  (i) it is identified as confidential 
when disclosed; or (ii) its nature or the circumstances of disclosure would reasonably indicate 
that it is confidential.
14.2
Exclusions
Confidential Information does not include information that the receiving Party can demonstrate:  
(i) is or becomes publicly available other than through a breach of this CRA; (ii) was lawfully 
known to the receiving Party without a confidentiality restriction before disclosure by the 
disclosing Party; (iii) is lawfully received from another Person without a confidentiality 
restriction and without breach of an obligation owed to the disclosing Party; (iv) is independently 
developed by or for the receiving Party without use of or reliance on the Confidential 
Information; or (v) is approved for disclosure by the disclosing Party in writing.
14.3
Use and Protection of Confidential Information
Page 50

PDF page 216

A Party receiving Confidential Information shall:  (i) use the Confidential Information only as 
reasonably necessary to perform, administer, enforce, or exercise its rights under this CRA; (ii) 
protect the Confidential Information using at least the same degree of care that it uses to protect 
its own confidential information of a similar nature, but in no event less than reasonable care;
(iii) disclose the Confidential Information only as permitted under this Article; and (iv) promptly 
notify the disclosing Party upon becoming aware of an unauthorized use or disclosure of the 
Confidential Information.
The receiving Party may disclose Confidential Information to its Affiliates, employees, officers, 
directors, attorneys, accountants, auditors, consultants, insurers, lenders, issuers of Credit 
Support, and other representatives that have a need to know the Confidential Information and are 
subject to confidentiality obligations or professional duties of confidentiality.
14.4
Tariff and Regulatory Requirements
Confidential Information shall be protected and disclosed in accordance with:  (i) applicable 
FERC regulations and orders; (ii) applicable state law and any applicable retail-service tariff;
(iii) any protective order or confidentiality agreement binding on the Parties; and (iv) this 
Article.
14.5
Permitted Regulatory and Administrative Disclosures
A Party may disclose Confidential Information to the extent reasonably necessary:  (i) to comply 
with the PJM Tariff, a FERC order, applicable law, legal process, or a request or requirement of 
a governmental authority with jurisdiction; (ii) to prepare, submit, support, or prosecute a filing, 
report, audit, formula-rate update, rate proceeding, tariff proceeding, or other regulatory 
submission; (iii) to administer a service request, study, billing determination, settlement, 
calculation, reconciliation, or Credit Support requirement relating to this CRA; (iv) to enforce 
this CRA or resolve a dispute arising under it; (v) to provide information to PJM reasonably 
necessary for Tariff administration, study, billing, settlement, or other administrative purposes 
relating to the Firm Transmission Service or this CRA; (vi) to provide information to an 
applicable state regulatory authority to the extent reasonably necessary in connection with retail 
service, retail Credit Support, or another state-jurisdictional arrangement relating to the Large 
Load Facilities; or (vii) with the written consent of the disclosing Party.
With respect to disclosures identified in clauses (i)-(vi), the Party making the disclosure shall 
notify the other Party so that such Party may seek a protective order or such other relief as such 
Party may deem appropriate under the circumstances. The Party making the disclosure may 
disclose only that portion of the Confidential Information which such Party is required to 
disclose.
14.6
No Limitation on Required Information Sharing
Eligible Customer may not withhold information reasonably required to calculate, verify, 
invoice, reconcile, or dispute an amount under this CRA solely because the information is 
Page 51

PDF page 217

confidential.
Large Load Customer may not withhold facility, project, load-ramp, operational, Credit Support, 
or other information within its possession or control that is reasonably required to administer this 
CRA solely because the information is confidential.
Transmission Owner’s receipt or use of such information shall remain subject to this Article and 
any other applicable confidentiality requirement.
14.7
Survival
The obligations under this Article shall survive expiration or termination of this CRA for five (5)
years; provided that (i) information constituting a trade secret shall remain protected for so long
as it qualifies as a trade secret under applicable law; and (ii) information protected for a longer 
period under applicable law, the PJM Tariff, a regulatory order, or a binding confidentiality 
agreement shall remain protected for that longer period.
ARTICLE 15
DISPUTE RESOLUTION
15.1
Notice of Dispute
A Party disputing an invoice, calculation, Credit Support Requirement, or other matter arising 
under this CRA shall provide the other Parties with written notice.  The disputing Party shall 
provide available supporting information reasonably necessary for the other Parties to evaluate 
the dispute.  A notice under this Section shall not excuse or delay performance except as 
expressly provided in this CRA. Notwithstanding the foregoing and for the avoidance of doubt, 
the Large Load Customer is not entitled to dispute resolution for its breach of Section 6.1.
15.2
Good-Faith Negotiation
Within ten (10) Business Days after receipt of a notice under Section 15.1, representatives of the 
Parties with responsibility for administering this CRA shall meet or confer and attempt in good 
faith to resolve the dispute.
If a Party does not request or participate in the Dispute resolution set forth in this Article 15 
within 10 Business Days following the delivered date of the written request initiating the 
process, such Party waives any further right to this Dispute resolution process.  The Dispute 
resolution process set forth in this Article 15 shall, in any event, be concluded within 30 days 
following the delivered date of the written request initiating the process or such longer period as 
the Parties may mutually agree.  Thereafter, any Party may exercise all remedies available at law 
or in equity under this CRA, including the initiation of court proceedings.
15.3
Continuation of Performance
While a dispute remains pending:
Page 52

PDF page 218

(a) each Party shall continue performing its obligations under this CRA to the maximum 
extent practicable;
(b) Large Load Customer shall timely pay each invoiced amount in accordance with 
Section 7.2, notwithstanding the dispute;
(c) Large Load Customer shall continue to cause Credit Support to be provided, 
maintained, increased, renewed, replaced, and replenished as required under Article 6;
(d) Transmission Owner may exercise its rights with respect to Credit Support in 
accordance with Articles 6 and 7; and
(e) no Party shall take action inconsistent with a final and binding determination 
resolving the dispute.
Payment or performance during a dispute shall not waive the paying or performing Party’s 
position or right to seek return of an overpayment or other appropriate relief.
15.4
No Suspension of Credit Support Rights
The initiation or pendency of a dispute shall not:  (i) prevent Transmission Owner from making a 
preservation draw under Section 6.4; (ii) suspend Transmission Owner’s right to draw on Credit 
Support for an invoiced amount not timely paid; (iii) relieve Large Load Customer of its
obligation to cause compliant Credit Support to be maintained; or (iv) extend the expiration, 
nonrenewal, replacement, or replenishment deadline applicable to Credit Support.
If the final resolution of a dispute determines that Large Load Customer paid, or Transmission 
Owner drew, more than the amount properly due, Transmission Owner shall return the excess to 
Large Load Customer or, if applicable, restore the excess Credit Support in accordance with 
Section 6.5.
If a Party receiving a written request to initiate the dispute-resolution process does not participate 
in that process within 10 Business Days after delivery of the written request, that Party waives its 
right to require completion of the informal dispute-resolution process before another Party 
pursues available remedies.  The dispute resolution process set forth in this Article 15 shall, in 
any event, be concluded within 30 days following the delivered date of the written request 
initiating the process or such longer period as the Parties may mutually agree.  
Thereafter, any Party may exercise all remedies available at law or in equity under this CRA, 
including the initiation of court proceedings.
ARTICLE 16
NOTICES
16.1
General Notices
All notices, demands, and other formal communications required or permitted under this CRA 
shall be in writing, and delivered to the applicable contacts identified in Section 16.2.
16.2
Notice Contacts
Page 53

PDF page 219

Eligible Customer
[Eligible Customer Name]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
With a copy to:
[Legal Department or Counsel]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
Large Load Customer,
[Large Load Customer Name]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
With a copy to:
[Legal Department or Counsel]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
Transmission Owner
[Transmission Owner Name]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
With a copy to:
[Legal Department or Counsel]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
Delivery of a copy shall not be required for a notice to become effective unless expressly stated 
Page 54

PDF page 220

otherwise in this CRA.
16.3
Credit Support Notices
All notices, demands, and communications concerning the issuance, amendment, increase, 
reduction, renewal, replacement, nonrenewal, expiration, disqualification, transfer, draw, or 
release of Credit Support shall also be delivered to the following designated Credit Support 
contacts:
Transmission Owner Credit Contact
[Name or Department]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
Large Load Customer Credit Contact
[Name or Department]
[Address]
[City, State ZIP Code]
Attention: [Name or Title]
Email: [Email Address]
Such notices may be sent by overnight courier, personal delivery, or electronic mail. A notice 
from an issuer shall be effective only if delivered as required by the letter of credit.
ARTICLE 17
GENERAL PROVISIONS
17.1
Amendment
This CRA may be amended only by a written instrument executed by authorized representatives 
of all Parties.
An amendment shall become effective only upon:  (i) acceptance or approval by FERC, if 
required; (ii) any approval or recognition required under the PJM Tariff; and (iii) satisfaction of 
any other requirement of applicable law.
An update to an Exhibit required under Section 3.2 shall not constitute an amendment for 
purposes of this Section.
17.2
Entire Agreement; Relationship to Other Agreements
This CRA and its Exhibits constitute the entire agreement between the Parties concerning the 
Firm Load Commitment and the payment, Credit Support, early-termination, and related 
administrative obligations established under this CRA.  
Page 55

PDF page 221

This CRA supersedes prior oral or written communications, negotiations, and understandings 
between the Parties concerning the subject matter of this agreement.  This CRA does not 
supersede or otherwise impact other agreements (which may include security or cost recovery 
provisions) that relate to the Large Load Facilities and that do not address matters set forth in this 
CRA related to Firm Load Commitments.
17.3
Severability
If a provision of this CRA is held invalid, unlawful, or unenforceable by FERC or another 
governmental authority or tribunal having jurisdiction, the remaining provisions shall remain in 
effect to the maximum extent permitted by law.
The Parties shall cooperate in good faith to replace the affected provision with a lawful and 
enforceable provision that preserves, to the greatest extent permitted by law, the original 
provision’s purpose and the economic protections established by this CRA.
If the affected provision cannot be replaced and its invalidity defeats the essential purpose of this 
CRA, the Parties’ rights shall be governed by the remaining enforceable provisions of this CRA 
and applicable law.
17.4
Governing Law
This CRA shall be governed by:  (i) federal law, including the Federal Power Act, and the PJM 
Tariff with respect to matters within federal jurisdiction; and (ii) the laws of the State of [State], 
without regard to its conflict-of-laws principles, with respect to matters not governed by federal 
law.
Nothing in this Section limits FERC’s jurisdiction or alters the allocation of jurisdiction between 
FERC, any state commission, and any court or other tribunal.
17.5
No Third-Party Beneficiaries
This CRA is entered into solely for the benefit of the Parties and their permitted successors and 
assigns.
Except as expressly provided in this CRA, no other Person, including PJM, another transmission 
customer, a Load Serving Entity, an issuer of Credit Support, or a governmental authority, shall 
have a right to enforce this CRA or be deemed a third-party beneficiary.
17.6
Relationship of the Parties
Nothing in this CRA creates or shall be construed to create:  (i) a partnership; (ii) a joint venture;
(iii) an agency relationship; (iv) a fiduciary relationship; or (v) an employment relationship
among any of the Parties..
Page 56

PDF page 222

17.7
Counterparts; Electronic Signatures
This CRA may be executed in any number of counterparts, each of which shall be deemed an 
original and all of which together shall constitute one instrument.
17.8
Indemnification
Eligible Customer and Large Load Customer shall, jointly and severally, to the fullest extent 
permitted by law, indemnify, defend upon request, and hold harmless Transmission Owner and 
its Representatives from and against all claims, damages, expenses, liabilities, and losses 
(including, without limitation, reasonable attorneys’ fees and expenses) asserted against, 
sustained, or incurred by Transmission Owner or its Representatives for any damage, harm, 
injury, or loss, of any kind, direct or indirect, to any property or person (including death), 
including, without limitation:
(a) claims for injuries or loss to employees of Transmission Owner, Eligible Customer,
Large Load Customer, or their respective Representatives, arising out of or relating to 
any act, omission, conduct, negligence or breach by Large Load Customer, or Eligible 
Customer, or their respective Representatives; 
(b) arising out of or relating to the work performed under or in connection with this CRA 
by Large Load Customer, Eligible Customer, or their respective Representatives;  and/or
(c) claims arising out of or relating to Large Load Customer’s, Eligible Customer’s, or 
their respective Representatives, contact or encounter with, compromise or disruption of, 
or loss or damage to any property of Transmission Owner or its Representatives’ 
property.  
Large Load Customer and Eligible Customer each specifically agree, to the fullest extent 
permitted by law, to assume liability for all personal injury claims brought by their respective 
employees or the employees of their respective Representatives in connection with this CRA and 
waive any limitation of liability defense based upon the applicable worker’s compensation law
and cases decided thereunder. Eligible Customer and Large Load Customer agree to indemnify 
and defend Transmission Owner and its Representatives from and against all such loss, expense 
damage or injury, including, without limitation, reasonable attorneys’ fees, which Transmission 
Owner’s Representatives may sustain as a result of personal injury claims by Eligible 
Customer’s or Large Load Customer’s employees or their respective Representatives’ employees 
or representatives.  
17.9
Enforcement Costs
Each of Eligible Customer and Large Load Customer shall reimburse Transmission Owner for 
all reasonable attorneys’ fees and expenses incurred in enforcing that Party’s obligations under 
this CRA, to the extent Transmission Owner prevails in the applicable action or proceeding. 
Notwithstanding the foregoing, Large Load Customer shall be solely responsible for all 
reasonable attorneys’ fees and expenses incurred by Transmission Owner in enforcing Large 
Load Customer’s payment or Credit Support obligations or collecting any amount due from 
Large Load Customer under this CRA.
Page 57

PDF page 223

17.10 Rules of Interpretation
The Parties intend that any grouping of words or phrases in a series of three or more shall be 
interpreted to include the use of the Oxford (or serial) comma regardless of whether such Oxford 
(or serial) comma is actually present in the series.
17.11 Survival
Expiration or termination of this CRA shall not affect:  (i) any payment obligation accrued or 
arising from a period before expiration or termination; (ii) any obligation to complete a 
calculation, invoice, reconciliation, refund, or return of an excess draw; (iii) any continuing right 
concerning Credit Support;  (iv) Large Load Customer’s obligation to pay any Shortfall Amount, 
Early Termination Amount, Partial Termination Amount, or other amount that survives 
expiration or termination; (v) Transmission Owner’s right to draw upon or apply Credit Support 
and its obligation to provide any required credit, refund, release, or reconciliation; (vi) the 
confidentiality and dispute-resolution provisions of Articles 14 and 15; or (vii) any other 
provision that expressly survives or that by its nature must survive to give effect to the Parties’ 
rights and obligations.
[Signature page follows]
Page 58

PDF page 224

IN WITNESS WHEREOF, the Parties, intending to be legally bound, have caused this CRA to 
be executed by their duly authorized representatives as of the date first written above.
TRANSMISSION OWNER:
[Name of Transmission Owner]
By: ______________________________
Name: ____________________________
Title: _____________________________
Date: _____________________________
ELIGIBLE CUSTOMER:
[Name of Eligible Customer]
By: ______________________________
Name: ____________________________
Title: _____________________________
Date: ____________________________
LARGE LOAD CUSTOMER:
[Name of Large Load Customer]
By: ______________________________
Name: ____________________________
Title: _____________________________
Date: _____________________________
Page 59

PDF page 225

EXHIBIT A
LARGE LOAD FACILITIES AND FIRM LOAD COMMITMENT
1.
Parties and Large Load Information
Transmission Owner:
[Name of Transmission Owner]
Eligible Customer:
[Name of Eligible Customer]
Large Load Customer:
[Name of Large Load Customer]
Large Load Facilities:
[Name and general description of the Large Load Facilities]
Facility Location:
[Street Address]
[City, State, ZIP Code]
Transmission Zone:
[Applicable PJM Transmission Zone]
Point of Delivery:
[Point of Delivery or other applicable delivery-point identifier]
2.
Term of Agreement: [__] Years
3.
Minimum Commitment Percentage:  [___] [add reduction schedule as 
applicable]%
4.
Initial Load and Firm Load Commitments
Eligible Customer’s Initial Load Commitment and Firm Load Commitment will be set forth in 
the following schedule:
Load-Ramp 
Stage
Service 
Date
Load Commitment / Associated Firm Transmission Service
Benchmark
1
[Date]
[___] MW
2
[Date]
[___] MW
Page 60

PDF page 226

3
[Date]
[___] MW
[Additional 
Stage]
[Date]
[___] MW
Final
[Date]
[___] MW
Following the update required under Section 3.2, the information in this Section 4 shall replace 
the Initial Load Commitment and shall establish the Firm Load Commitment for purposes of this
CRA.
The Firm Load Commitment applicable during any Measurement Period is the amount of total 
load from the Large Load Facilities that is anticipated to be in service under the foregoing 
schedule if the Eligible Customer is taking NITS on behalf of the Large Load.  If the Eligible 
Customer is taking FCDS or Firm Point-to-Point Transmission Service on behalf of the Large 
Load, the Firm Load Commitment applicable during any Measurement Period is the amount of 
such Firm Transmission Service for which the Eligible Customer has contracted or reserved, as 
applicable, during such period.
If a subsequent Service Date occurs during a Measurement Period, the Firm Load Commitment 
applicable before and after that Service Date shall be determined separately for the applicable 
portions of the Measurement Period in accordance with Exhibit B.
5.
Service Dates
The first Service Date under this Exhibit A is [Date].
The final Service Date under this Exhibit A is [Date].
6.
Commercial Operation Date
The anticipated Commercial Operation Date for the Large Load Facilities is [Date]. The 
anticipated Commercial Operation Date is not a guarantee of service on such date.
Except as expressly provided in the CRA, a change in the anticipated or actual Commercial 
Operation Date does not modify:
a Service Date;
the Firm Load Commitment;
the Committed Revenue Contribution;
the Credit Support Requirement; or
any other obligation under the CRA.
7.
Relationship to Actual Load and Firm Transmission Service
The Firm Load Commitment is a contractual benchmark reflecting the anticipated load 
associated with the Large Load Facilities and the corresponding Firm Transmission Service
Page 61

PDF page 227

commitment on which the CRA is based. It is not a statement of the Large Load Facilities' actual 
demand during any Measurement Period.
8.
Update and Amendment History
The following table will identify each update or amendment of this Exhibit A that becomes 
effective under Section 3.2 or Article 17 of the CRA:
Update or 
Amendment No.
Effective 
Date
Description of Update 
or Amendment
Final PJM Agreement Identifier or 
FERC Docket No./Order Date, as 
Applicable
[___]
[Date]
[Description]
[Final PJM Agreement Identifier or 
Docket No./Order Date]
[___]
[Date]
[Description]
[Final PJM Agreement Identifier or 
Docket No./Order Date]
[___]
[Date]
[Description]
[Final PJM Agreement Identifier or 
Docket No./Order Date]
An update required under Section 3.2 shall become effective without further agreement or 
signature of the Parties and shall not constitute an amendment to the CRA, except to the extent a 
filing with or acceptance by FERC is required. Any other change to this Exhibit A shall be made 
in accordance with Article 17.
Unless and until an update or amendment becomes effective in accordance with the CRA, the 
then-effective Firm Load Commitment and Service Dates will continue to control.
Page 62

PDF page 228

EXHIBIT B
REVENUE CONTRIBUTION AND SHORTFALL CALCULATION
1. Applicable Firm Load Commitment
For each Measurement Period, the “Applicable Firm Load Commitment” shall mean each 
amount of the Firm Load Commitment scheduled to apply during that Measurement Period 
under Exhibit A.
If more than one load level is scheduled to apply during a Measurement Period, each load level 
shall apply for the portion of the Measurement Period during which it is scheduled to be 
effective.
The Applicable Firm Load Commitment shall not be reduced or deferred based on:
the amount of load that actually materializes;
the amount of Firm Transmission Service actually taken to serve the Large Load 
Facilities; or
the actual operating level of the Large Load Facilities.
2. Full Firm Transmission Service Benchmark
For each Measurement Period, the “Full Firm Transmission Service Benchmark” shall equal 
100% of the Firm Transmission Service-related charges that would apply if Eligible Customer 
took Firm Transmission Service corresponding to the Applicable Firm Load Commitment during 
that Measurement Period.
The Full Firm Transmission Service Benchmark shall be calculated using:
the Applicable Firm Load Commitment;
the Applicable Firm Transmission Service Rate;
the generally applicable rate components and billing determinants used under the PJM 
Tariff and Transmission Owner’s applicable FERC-jurisdictional rate to calculate charges 
for  Firm Transmission Service; and
the portion of the Measurement Period during which each applicable load level and 
Applicable Firm Transmission Service Rate applies.
If the Applicable Firm Load Commitment or Applicable Firm Transmission Service Rate 
changes during a Measurement Period, the Full Firm Transmission Service Benchmark shall 
equal the sum of the amounts separately calculated for each applicable portion of the 
Measurement Period.
3. Committed Revenue Contribution
For each Measurement Period, the Committed Revenue Contribution = Minimum Commitment 
Percentage × Full Firm Transmission Service Benchmark
The Minimum Commitment Percentage shall be the percentage specified in Exhibit A.
Page 63

PDF page 229

The Minimum Commitment Percentage shall be applied only to the Full Firm Transmission 
Service Benchmark and shall not be applied to the Actual Revenue Contribution.
4. Actual Revenue Contribution
For each Measurement Period, the Actual Revenue Contribution shall equal the Firm 
Transmission Service-related revenues paid or payable to PJM for remittance or allocation to 
Transmission Owner, or otherwise paid or payable to Transmission Owner, that are attributable 
to transmission service actually taken to serve the Large Load Facilities.
The Actual Revenue Contribution shall include amounts to the extent those amounts:
are attributable to Firm Transmission Service taken by Eligible Customer to serve the 
Large Load Facilities;
correspond to the same categories of rate components included in the Full Firm 
Transmission Service Benchmark; and
have not been refunded, reversed, or otherwise credited to the payer.
To the extent the applicable Firm Transmission Service methodology uses an assigned 
Network Service Peak Load contribution or another allocated billing determinant, the 
Actual Revenue Contribution shall be calculated using:
the billing determinant assigned to the Large Load Facilities for the applicable 
Measurement Period; and
the same categories of rates and rate components used to calculate the Full Firm 
Transmission Service Benchmark.
5. Actual Billing Determinant and Allocation
If Firm Transmission Service-related charges or billing determinants attributable to the Large 
Load Facilities are aggregated with charges or billing determinants attributable to other load, 
Transmission Owner shall determine the portion attributable to the Large Load Facilities using, 
in the following order of priority:
PJM billing and settlement data that separately identifies the Large Load Facilities;
metering or other load data for the Large Load Facilities, applied in accordance with the 
generally applicable billing and allocation methodology under the PJM Tariff; and
if the foregoing information is insufficient, other information supplied by Eligible 
Customer or the applicable billing or service entity that Transmission Owner reasonably 
determines is sufficient to identify and verify the portion attributable to the Large Load 
Facilities.
Eligible Customer shall provide, or cause the applicable billing or service entity to provide, 
information reasonably necessary to identify and verify the portion attributable to the Large Load 
Facilities.
6. Included Rate Components
Page 64

PDF page 230

The same categories of Firm Transmission Service rate components shall be used to calculate the 
Full Firm Transmission Service Benchmark and the Actual Revenue Contribution.  The included 
rate components shall be derived from the applicable zonal Firm Transmission Service rate.
The following amounts shall be excluded:
charges for electric energy;
charges for generation capacity;
retail electric service or distribution-service charges;
penalties or charges for unreserved transmission use;
administrative-service or ancillary-service charges, unless expressly included above;
interest, late-payment charges, taxes, and fees unrelated to the included Firm 
Transmission Service rate components; and
amounts attributable to load other than the Large Load Facilities.
7. Applicable Firm Transmission Service Rate
The Applicable Firm Transmission Service Rate for each Measurement Period shall be the 
applicable zonal rate then in effect under the PJM Tariff and Transmission Owner’s FERC-
jurisdictional rate for Firm Transmission Service in the applicable Transmission Zone.
If an applicable zonal Firm Transmission Service Rate changes during a Measurement Period, 
each rate shall apply to the portion of the Measurement Period during which it was in effect.
8. Shortfall Amount
For each Measurement Period, the Shortfall Amount = Committed Revenue Contribution • 
Actual Revenue Contribution
If the Actual Revenue Contribution equals or exceeds the Committed Revenue Contribution, the 
Shortfall Amount shall be zero.
9. Separate Measurement Periods
Each Measurement Period shall be calculated independently. Any amount by which the Actual 
Revenue Contribution exceeds the Committed Revenue Contribution for one Measurement 
Period shall not reduce a Shortfall Amount for another Measurement Period, be carried forward 
or backward, or entitle Large Load Customer to any payment, refund, or credit.
10. Partial Measurement Periods
For any partial Measurement Period, the Full Firm Transmission Service Benchmark, Committed 
Revenue Contribution, Actual Revenue Contribution, and Shortfall Amount shall be calculated 
for the portion of the Measurement Period falling within the Term.
The Full Firm Transmission Service Benchmark shall be prorated in accordance with the billing 
interval applicable to the Applicable Firm Transmission Service Rate, based on the portion of the 
Page 65

PDF page 231

Measurement Period during which each applicable load level and Applicable Firm Transmission 
Service
Rate 
was 
effective.
Page 66

PDF page 232

EXHIBIT C
CREDIT SUPPORT REQUIREMENT AND SCHEDULE
1. Credit Support Requirement
The Credit Support Requirement is intended to secure Large Load Customer’s projected 
financial exposure under the CRA for the remaining Term and does not determine or limit any 
amount otherwise payable by Large Load Customer under the CRA.
At execution by the Parties, the Initial Credit Support Requirement shall be calculated using the 
Initial Load Commitment, anticipated Service Dates, estimated Applicable Firm Transmission 
Service Rate, and other information then available, and the methodology specified below. 
The Initial Credit Support Requirement shall equal the aggregate Projected Full Firm 
Transmission Service Benchmarks for the full Term of this CRA beginning on the first Service 
Date through the end of the Term.
Following the update required under Section 3.2 after execution of the Final PJM Agreement, 
Transmission Owner shall recalculate the Credit Support Requirement using the updated Firm 
Load Commitment, Service Dates, Applicable Firm Transmission Service Rate, and Projected 
Full Firm Transmission Service Benchmarks for the remainder of the Term. The recalculated 
Credit Support Requirement shall replace the Initial Credit Support Requirement.
At the end of each Measurement Period, Transmission Owner shall recalculate Large Load 
Customer’s Credit Support Requirement. The recalculation shall equal the aggregate Projected 
Full Firm Transmission Service Benchmarks for the remaining Term. Transmission Owner shall 
exclude a completed Measurement Period from the Credit Support Requirement only after:
(i) Transmission Owner has finally calculated the Committed Revenue Contribution, Actual 
Revenue Contribution, and any resulting Shortfall Amount for that Measurement Period; and
(ii) Large Load Customer has paid all amounts due for that Measurement Period.
Transmission Owner shall provide Large Load Customer with notice after each recalculation, 
and the revised Credit Support Requirement shall become effective in accordance with Section 
6.5 of the CRA. These recalculations shall not constitute an amendment to this Exhibit or the 
CRA.
2. Calculation of Projected Full Firm Transmission Service Benchmarks
For each Measurement Period included in the Credit Support Requirement, the Projected Full 
Firm Transmission Service Benchmark shall equal 100% of the Firm Transmission Service-
related charges that would apply if Eligible Customer took Firm Transmission Service 
corresponding to the Initial Load Commitment or Firm Load Commitment, as applicable, 
scheduled to apply during that Measurement Period.
The Credit Support Requirement shall equal the aggregate Projected Full Firm Transmission 
Service Benchmarks for all Measurement Periods included in the applicable calculation.
Page 67

PDF page 233

The Projected Full Firm Transmission Service Benchmark shall be calculated using:
the Initial Load Commitment or Firm Load Commitment, as applicable, and set forth in 
Exhibit A;
the Applicable Firm Transmission Service Rate in effect or estimated to apply, as 
applicable, at the time of calculation;
any rate change accepted by FERC and scheduled to become effective during the 
applicable Measurement Period;
the rate components and billing determinants identified in Exhibit B; and
the portion of each Measurement Period during which each applicable load level and 
Applicable Firm Transmission Service Rate is scheduled to apply.
3. No Reduction for Minimum Commitment Percentage or Projected Actual Revenues
The Credit Support Requirement shall be calculated using 100% of the Projected Full Firm 
Transmission Service Benchmarks and shall not be reduced by:
the Minimum Commitment Percentage; or
any projected or estimated Actual Revenue Contribution.
Actual Revenue Contributions shall be credited in determining the Shortfall Amount for a 
completed Measurement Period in accordance with Article 5 and Exhibit B.
After the calculation for a completed Measurement Period has been finalized and Large Load 
Customer has paid all amounts due for that Measurement Period, that Measurement Period shall 
be excluded from the Credit Support Requirement in accordance with Sections 1 and 4 of this 
Exhibit.
For avoidance of doubt, Actual Revenue Contributions attributable to a completed Measurement 
Period shall not reduce the Projected Full Firm Transmission Service Benchmark for any future 
Measurement Period.
4. Recalculation
Transmission Owner shall recalculate the Credit Support Requirement:
following the update required under Section 3.2 after execution of the Final PJM 
Agreement;
after the Committed Revenue Contribution, Actual Revenue Contribution, and any 
resulting Shortfall Amount for a completed Measurement Period have been finally 
calculated and Large Load Customer has paid all amounts due for that Measurement 
Period in accordance with Section 1 of this Exhibit;;
following an effective modification to the Firm Load Commitment or a Service Date;
following an effective Partial Termination;
following a change in the Applicable Firm Transmission Service Rate that has become 
effective, or a rate change that has been accepted by FERC and is scheduled to become 
effective during a Measurement Period included in the Credit Support Requirement; 
Page 68

PDF page 234

upon replacement of Credit Support following an issuer downgrade, disqualification, 
expiration, termination, or notice of nonrenewal; and
as otherwise expressly required under the CRA.
Transmission Owner shall provide notice of each such recalculation, and the revised Credit 
Support Requirement shall become effective in accordance with Section 6.5 of the CRA.  These 
updates shall not constitute an amendment to this Exhibit or the CRA generally.
5. Letter of Credit Issuer Requirements
A financial institution issuing a letter of credit under the CRA shall:
maintain a long-term unsecured credit rating of [at least “A-” from S&P Global Ratings 
or Fitch Ratings or “A3” from Moody’s Investors Service] [insert alternative credit rating 
requirement if applicable];
satisfy the requirements of Article 6 and any attachments to this Exhibit; and
otherwise satisfy Transmission Owner’s generally applicable credit requirements.
6. Treatment of Prior Draws
A draw applied to an unpaid amount shall not reduce the Credit Support Requirement. Large 
Load Customer shall cause the Credit Support to be restored to the then-applicable Credit 
Support Requirement in accordance with Section 6.7 of the CRA.
A preservation draw under Section 6.4 shall not reduce the Credit Support Requirement because 
the proceeds continue to be held as cash security securing Large Load Customer’s obligations 
under the CRA.
In determining the amount of replacement or additional Credit Support required, cash security 
held by Transmission Owner and legally available to secure the same obligations shall be 
credited against the otherwise applicable Credit Support Requirement.
7. Relationship to Amounts Payable
The Credit Support Requirement is a measure of secured exposure and does not determine or 
limit:
the actual Committed Revenue Contribution;
the Actual Revenue Contribution;
the Shortfall Amount for a completed Measurement Period; or
any amount otherwise payable under the CRA.
Page 69

PDF page 235

EXHIBIT C, ATTACHMENT [__]
Page 70

PDF page 236

EXHIBIT D
EARLY AND PARTIAL TERMINATION AMOUNT SCHEDULE
1. Applicable Termination Percentage
The Applicable Termination Percentage for an Early Termination or Partial Termination shall be 
determined based on the date on which the termination or Partial Termination becomes effective, 
as follows:
Effective Date of Termination or Partial Termination Applicable Termination Percentage
On or after the Effective Date and before execution of the 
Final PJM Agreement
25%
On or after execution of the Final PJM Agreement through 
the 180th day after execution of the Final PJM Agreement 50%
After the 180th day after execution of the Final PJM 
Agreement but before the first Service Date
75%
On or after the first Service Date
100%
2. Early Termination Amount
The Early Termination Amount shall be calculated in accordance with Article 9 and this Exhibit 
of the CRA as follows:
Early Termination Amount = (Applicable Termination Percentage × Present Value of Remaining 
Projected Committed Revenue Contributions) • Applicable Credits 
The Applicable Termination Percentage used in the calculation shall be the percentage specified 
in Section 1 of this Exhibit for the date on which the termination becomes effective.
Before execution of the Final PJM Agreement, the Early Termination Amount shall be calculated 
using the Initial Load Commitment, anticipated Service Dates, estimated Applicable Firm 
Transmission Service Rate, and other information then reflected in Exhibits A and C. After 
execution of the Final PJM Agreement, the calculation shall use the updated information 
provided pursuant to Section 3.2.
The Early Termination Amount shall not be less than zero.
3. Present Value of Remaining Projected Committed Revenue Contributions
The Present Value of Remaining Projected Committed Revenue Contributions shall be 
calculated as of the effective date of termination for the period beginning on the effective date of 
termination and ending on the date the fixed period specified in Section 4.2(i) of the CRA would 
have expired absent the termination.
Page 71

PDF page 237

The calculation shall be based on:
the Initial Load Commitment or Firm Load Commitment, as applicable, and Service 
Dates in effect immediately before termination;
the Minimum Commitment Percentage;
the Projected Full Firm Transmission Service Benchmark determined in accordance with 
Exhibit C;
the Applicable Firm Transmission Service Rate in effect or estimated to apply, as 
applicable, on the effective date of termination; 
any rate change accepted by FERC and scheduled to become effective during the 
remaining fixed period;
the rate components and billing determinants identified in Exhibit B; and
Transmission Owner’s then-effective FERC-approved weighted average cost of capital as 
the discount rate.
No rate escalation or other projected rate change shall be included unless the rate change has 
been accepted by FERC and is scheduled to become effective during the remaining fixed period.
4. Applicable Credits
Applicable Credits shall include, without duplication:
any Actual Revenue Contribution attributable to the portion of the Measurement Period 
occurring before the effective date of termination that has been paid or is payable and has 
not otherwise been credited;
any Shortfall Amount, Credit Support proceeds, or other amount previously collected and 
applied to the same revenue exposure; and
any Early Termination Offset Amount determined under Section 9.9 of the CRA.
No amount shall be treated as an Applicable Credit unless it has been paid, received, or applied 
to the revenue exposure included in the Early Termination Amount.
5. Partial Termination Amount
Unless the permanently reduced portion of the Firm Load Commitment consists of a separately 
identifiable load tranche, the Partial Termination Amount shall equal:
Partial Termination Amount = Early Termination Amount × (Permanently Reduced MW ÷ 
applicable Initial Load Commitment or Firm Load Commitment immediately before reduction) 
The Applicable Termination Percentage shall be the percentage specified in Section 1 of this 
Exhibit for the effective date of the Partial Termination.
If the permanently reduced portion consists of one or more separately identifiable load tranches, 
the Partial Termination Amount shall be calculated using the Projected Committed Revenue 
Contributions attributable to the terminated tranche or tranches, including the applicable MW 
amount and Service Date for each terminated tranche.
Page 72

PDF page 238

The Partial Termination Amount shall not be less than zero.
6. Treatment After the First Service Date
On and after the first Service Date, the Applicable Termination Percentage shall remain 100%.
The Present Value of Remaining Projected Committed Revenue Contributions will decline as the 
remaining portion of the fixed period decreases. Accordingly, the Applicable Termination 
Percentage will not be separately reduced based solely on the passage of time after the first 
Service Date.
7. Early Termination Offset Amount
If an Early Termination Offset Amount is quantifiable when Transmission Owner issues the 
applicable termination invoice, Transmission Owner shall include that amount as an Applicable 
Credit.
If all or part of the Early Termination Offset Amount becomes quantifiable after the termination 
invoice is issued, Transmission Owner shall reflect the amount in a subsequent reconciliation and 
promptly return any resulting excess payment to Large Load Customer in accordance with 
Articles 7 and 9 of the CRA.
Nothing in this Exhibit requires Transmission Owner to market the Point of Delivery, solicit 
replacement load, modify its transmission planning or service processes, or enter into a 
transmission-service arrangement with another Person.
8. No Duplicate Recovery
The Early Termination Amount and Partial Termination Amount are forward-looking amounts 
intended to address projected revenue exposure arising after the effective date of termination or 
Partial Termination.
Transmission Owner shall not recover the same revenue exposure through both:
a Shortfall Amount; and
an Early Termination Amount or Partial Termination Amount.
Amounts collected before termination or Partial Termination shall be credited only to the extent 
required under Article 9 and this Exhibit to prevent duplicate recovery.
Page 73

PDF page 239

706
Rates and Charges
Eligible Customers taking Interim Network Integration Transmission Service shall pay the 
charges set forth in this Section 706.
706.1 Monthly Demand Charge
Eligible Customer shall pay a Monthly Demand Charge for Zone Network Load and Non-Zone 
Network Load, which shall be determined as follows: Eligible Customer’s measured demand 
amount (in MWs) multiplied by the applicable zonal Network Integration Transmission Service 
rate established pursuant to Section 34.1.
Revenue Crediting.  Each month, revenue credits will be applied to the gross monthly Demand 
Charge to determine the actual charge to the Transmission Customer.  Revenue credits shall be 
calculated based on the sum of the applicable Zone’s share of revenues collected during the 
month from the Non-Firm Contract Demand Charge under Schedule 19.  The sum of these 
revenues will appear as a reduction to the gross monthly rate stated above on a Transmission 
Customer’s bill in that month for service under this schedule.  
706.2 Redispatch Charge
The Eligible Customer shall pay any redispatch costs as set forth in Tariff, Attachment K.
706.3 Stranded Cost Recovery
Any Transmission Owner may seek to recover stranded costs from the Eligible Customer 
pursuant to this Tariff in accordance with the terms, conditions and procedures set forth in FERC 
Order No. 888.  However, the Transmission Owner must separately file any proposal to recover 
stranded costs under section 205 of the Federal Power Act.
706.4 Other Charges
Eligible Customer shall pay administrative services charges under Tariff, Schedule 1A; Tariff, 
Schedule 9; and Tariff, Schedule 10, consistent with the charges assessed to loads taking 
Network Integration Transmission Service.
Eligible Customer shall pay Ancillary Services charges in accordance with Tariff, Part I, 
section 3. 
Eligible Customer shall pay Black Start Service charges in accordance with Tariff, Schedule 6A.
Page 74

PDF page 240

714 
Rates and Charges for Firm Contract Demand Transmission Service
Eligible Customers taking Firm Contract Demand Transmission Service on behalf of Eligible 
Load or Large Load shall pay the charges set forth in this Section 714.
714.1 Monthly Demand Charge
Eligible Customer taking service on behalf of Eligible Load or Large Load shall pay a Monthly 
Demand Charge based on the Firm Contract Demand Transmission Service amount (MW), as 
specified in Eligible Customer’s Service Agreement, in accordance with Tariff, Schedule 18.
Page 75

PDF page 241

715 
Rates and Charges for Non-Firm Contract Demand Transmission Service
Eligible Customers taking Non-Firm Contract Demand Transmission Service shall pay the 
charges set forth in this Section 715.
715.1 Monthly Demand Charge
Eligible Customer shall pay a discounted reservation rate set as a function of the Zonal Firm 
Contract Demand Transmission Service rate and the transmission system load factor for a Zone, 
as specified in Eligible Customer’s Service Agreement, in accordance with Tariff, Schedule 19.
Page 76

PDF page 242

SCHEDULE 7
Long-Term Firm and Short-Term Firm Point-To-Point
Transmission Service
1) The Transmission Customer shall pay each month for Reserved Capacity at the sum of the applicable charges set forth below for the Point of Delivery:
Summary of Charges
(in $/kW)
Point of Delivery
Yearly Charge
Monthly Charge
Weekly Charge
Daily On-Peak1/
Charge
Daily Off-Peak2/
Charge
Border of PJM3/
Border Yearly Charge 
established pursuant to 
section 11 below
Yearly Charge /12
Yearly Charge /52
Weekly Charge /5
Weekly Charge /7
AE Zone
23.809
1.984
0.4580
0.0920
0.0650
BGE Zone
15.675
1.306
0.3010
0.0600
0.0430
Delmarva Zone
19.378
1.615
0.3730
0.0750
0.0530
JCPL Zone
15.112
1.259
0.2906
0.0581
0.0414
MetEd Zone
15.112
1.259
0.2906
0.0581
0.0414
Penelec Zone
15.112
1.259
0.2906
0.0581
0.0414
PECO Zone
26.264
2.189
0.5051
0.1010
0.0722
PPL Zone: Total charge is the sum of 
the components
PPL: *
AEC: 0.463
UGI: *
PPL: *
AEC: 0.039
UGI: *
PPL: *
AEC: 0.0089
UGI: *
PPL: *
AEC: 0.0018
UGI: *
PPL: *
AEC: 0.0013
UGI: *
Page 77

PDF page 243

Point of Delivery
Yearly Charge
Monthly Charge
Weekly Charge
Daily On-Peak1/
Charge
Daily Off-Peak2/
Charge
Pepco Zone
20.999
1.750
0.4040
0.0810
0.0580
PSE&G Zone
23.696
1.975
0.4557
0.0911
0.0651
AP Zone
Rate Pursuant to Attachment H-
11 and Attachment H-34
Rate Pursuant to 
Attachment H-11 and 
Attachment H-34
Rate Pursuant to Attachment 
H-11 and Attachment H-34
Rate Pursuant to Attachment 
H-11 and Attachment H-34
Rate Pursuant to 
Attachment H-11 and 
Attachment H-34
Rockland Zone
53.766
4.481
1.0340
0.2068
0.1477
ComEd Zone4/
5/
AEP East Zone6/
Rate Pursuant to 
Attachment H-14 and 
Attachment H-20
Rate Pursuant to 
Attachment H-14 and 
Attachment H-20
Rate Pursuant to Attachment 
H-14 and Attachment H-20
Rate Pursuant to Attachment 
H-14 and Attachment H-20
Rate Pursuant to 
Attachment H-14 and 
Attachment H-20
Dayton Zone
Rate Pursuant to 
Attachment H-15
Rate Pursuant to 
Attachment H-15
Rate Pursuant to Attachment 
H-15
Rate Pursuant to Attachment 
H-15
Rate Pursuant to 
Attachment H-15
Duquesne Zone
14.17
1.18
0.27
0.0540
0.0386
Dominion Zone7/
ATSI Zone
Rate Pursuant to 
Attachment H-21
Rate Pursuant to 
Attachment H-21
Rate Pursuant to 
Attachment H-21
Rate Pursuant to 
Attachment H-21
Rate Pursuant to 
Attachment H-21
DEOK Zone
Rate Pursuant to 
Attachment H-22
Rate Pursuant to 
Attachment H-22
Rate Pursuant to 
Attachment H-22
Rate Pursuant to 
Attachment H-22
Rate Pursuant to 
Attachment H-22
EKPC Zone
Rate Pursuant to 
Attachment H-24
Rate Pursuant to 
Attachment H-24
Rate Pursuant to 
Attachment H-24
Rate Pursuant to 
Attachment H-24
Rate Pursuant to 
Attachment H-24
Page 78

PDF page 244

OVEC Zone
5.16
0.43
0.10
0.02
0.014
* PPL Electric Utilities Corporation’s and UGI Utilities’ respective component of the total charge is posted on the PJM Internet website.
1/
Monday – Friday except the following holidays:  New Years Day, Memorial Day, Independence Day, Labor Day, Thanksgiving Day, and Christmas Day.
2/
Saturday and Sunday and the following holidays:  New Years Day, Memorial Day, Independence Day, Labor Day, Thanksgiving Day, and Christmas Day.
3/
The charge for Points of Delivery at the Border of PJM shall not apply to any Reserved Capacity with a Point of Delivery of the Midcontinent Independent 
Transmission System Operator, Inc.
4/
Each month, revenue credits will be applied to the gross charge in accordance with section 8 below to determine the actual charge to the Transmission Customer. 
5/
The charges for the ComEd zone are posted on PJM’s website.  In addition to other rates set forth in this schedule, customers within the ComEd zone shall be 
charged for recovery of RTO start-up costs at the following rates, each computed to four decimal places:
Annual Rate - $/kW/year = $1,523,039, divided by the 1 CP demand for the ComEd zone for the prior calendar year;
Monthly Rate - $/kW/month. = Annual Rate divided by 12;
Weekly Rate - $/kW/week = Annual Rate divided by 52;
Daily Rate - $/kW/day = Weekly Rate divided by 5.
In order to ensure that the charge does not result in either an over-recovery or under-recovery of ComEd’s start-up costs, PJM will institute an annual true-up 
mechanism in the month of May of each of the years 2008-2014.  In May of each of those years, PJM will compare the amount collected under this charge for the 
previous 12 months with the target annual amount of $1,523,039 and calculate any credits or surcharges that would be needed to ensure that $1,523,039 is collected 
for each year.  Any credit or surcharge will be assessed in the June bills for years 2008-2014, consistent with the above methodology.
6/
The rates for firm point-to-point transmission service in the AEP Zone will be charged at the yearly, monthly, weekly or daily rate equivalent to the rate effective in 
such period under Attachments H-14 and H-20. In addition to other rates set forth in this schedule, customers within the AEP East Zone shall be charged for 
recovery of RTO start-up costs at the following rates, each computed to four decimal places:
Annual Rate - $/kW/year = $2,362,185, plus any applicable true-up adjustment, divided by the 1 CP demand for the AEP East Zone for the prior calendar year;
Monthly Rate - $/kW/month. = Annual Rate divided by 12;
Weekly Rate - $/kW/week = Annual Rate divided by 52;
Daily Rate - $/kW/day = Weekly Rate divided by 5.
Page 79

PDF page 245

For the period November 1, 2005 through March 31, 2006, the rate shall be $8.94/MW-month; for the period April 1 through December 31, 2006, the rate shall be 
$8.60/MW-month, thereafter, the rate will be subject to the following true-up:
In order to ensure that the charge does not result in either over-recovery or under-recovery of AEP’s start-up costs, PJM will institute an annual true-up mechanism 
and implement revised charges as of January 1st of each of the years 2007-2019.  In January of each of those years, PJM will compare the amount collected under 
this charge for the previous year or part thereof with the target annual amount of $2,362,185 and calculate the rates that would be needed, given the expected billing 
demands, to collect $2,362,185, adjusted for any prior year over-collection or under-collection.  In the final year that the rate is collected, PJM will calculate the rate 
to collect five-twelfths of the annual amount ($984,244), plus or minus any prior year true up amount, by May 31 of that year, and shall charge such rate until that 
amount is collected, whether that date be before or after May 31, 2020.   
7/
The service period charges rounded to four decimal places for the Dominion Zone are as follows:
Yearly Charge - $/kW/year = the formula rate for Network Integration Transmission Service as described in Attachment H-16 and Attachment H-16A 
divided by 1000 kW/MW
Monthly Charge - $/kW/month. = Yearly Charge divided by 12;
Weekly Charge - $/kW/week = Yearly Charge divided by 52;
Daily On-Peak Charge - $/kW/day = Weekly Charge divided by 5;
Daily Off-Peak Charge - $/kW/day = Weekly Charge divided by 7.
On a monthly basis, revenue credits shall be calculated based on the sum of VEPCO’s share of revenues collected during the month from Schedule 7 and Network 
Integration Transmission Service to Non-Zone Network Load under Attachment H-A.  The sum of these revenue credits will appear as an adjustment to the to the 
gross monthly service period charges produced by the above formula.
2)
The total demand charge in any week, pursuant to a reservation for Daily On-Peak Delivery, or Daily Off-Peak Delivery shall not exceed the Weekly Delivery rate 
specified in section (1) above for weekly service times the highest amount in kilowatts of Reserved Capacity and any additional transmission service, if any, in any day during such 
week.
Page 80

PDF page 246

3)
Discounts:  Three principal requirements apply to discounts for transmission service as follows:  (1) any offer of a discount made by the Transmission Provider must be 
announced to all Eligible Customers solely by posting on the OASIS, (2) any customer-initiated requests for discounts (including requests for use by one’s wholesale merchant or 
an Affiliate’s use) must occur solely by posting on the OASIS, and (3) once a discount is negotiated, details must be immediately posted on the OASIS.  For any discount agreed 
upon for service on a path, from point(s) of receipt to point(s) of delivery, the Transmission Provider must offer the same discounted transmission service rate for the same time 
period to all Eligible Customers on all unconstrained transmission paths that go to the same point(s) of delivery on the Transmission System.
4)
Congestion, Losses and Capacity Export:  In addition to any payment under this Schedule, the Transmission Customer shall pay Redispatch Costs as specified in Section 
27 of the Tariff.  The Transmission Customer shall be responsible for losses as specified in the Tariff.  Any Transmission Customer that is a Capacity Export Transmission 
Customer, shall pay any applicable charges, and receive any applicable credits, for such a customer pursuant to Attachment DD.
5)
Other Supporting Facilities and Taxes:  In addition to the rates set forth in section (1) of this schedule, the Transmission Customer shall pay charges determined on a 
case-by-case basis for facilities necessary to provide Transmission Service at voltages lower than those shown in Attachment H for the applicable Zone(s) and any amounts 
necessary to reimburse PJMSettlement for any amounts payable as sales, excise, “Btu,” carbon, value-added or similar taxes (other than taxes based upon or measured by net 
income) with respect to the amounts payable pursuant to the Tariff.
6)
[Reserved]
7)
Transmission Enhancement Charges. Except for Points of Delivery at the Border of PJM, which are subject to the Border Yearly Charge determined under section 11, in 
addition to the rates set forth in section (1) of this Schedule and any other applicable charges, the Transmission Customer shall also pay any Transmission Enhancement Charges 
for which it is designated as a Responsible Customer under Schedule 12 appended to the Tariff.
8)
Determination of monthly charges for ComEd Zone: On a monthly basis, revenue credits shall be calculated based on the sum of ComEd’s share of revenues collected 
during the month from: (i) the PJM Border Rate under Schedule 7; (ii) Network Integration Transmission Service to Non-Zone Network Load under Attachment H-A; (iii) Seams 
Elimination Charge/Cost Adjustment/Assignment (“SECA”) revenues allocable to ComEd under the Tariff; and (iv) any Point-To-Point Transmission Service where the Point of 
Receipt and the Point of Delivery are both internal to the ComEd Zone. On this basis, the sum of these revenues will appear as a reduction to the gross monthly rate stated above 
on a Transmission Customer’s bill in that month for service under this schedule.
9)
Determination of monthly charges for AEP Zone: On a monthly basis, revenue credits shall be calculated based on the sum of AEP’s share of revenues collected during 
the month from: (i) the PJM Border Rate under Schedule 7; (ii) Network Integration Transmission Service to Non-Zone Network Load under Attachment H-A; and (iii) Firm 
Point-To-Point Transmission Service where the Point of Delivery is internal to the AEP Zone. The sum of these revenue credits will appear as an adjustment (reduction) to the 
gross monthly rate stated above on a Transmission Customer’s bill in that month for service under this schedule.
Page 81

PDF page 247

10)
Resales:  The rates and rules governing charges and discounts stated above shall not   apply to resales of transmission service, compensation for which shall be governed by 
section 23.1 of the Tariff.
11)
Determining the Border Yearly Charge
(A) Formula for Determining the Border Yearly Charge
(i)  Beginning with the calendar year 2020, the Border Yearly Charge shall be based on the following formula:
BYC = SHRR/SZPL
Where:
BYC is the Border Yearly Charge stated in dollars per kW of Reserved Capacity; 
SHRR is the sum of the Revenue Requirements for each Transmission Owner used to determine charges for Network Integration Transmission Service either (a) 
stated in Attachment H for a Transmission Owner or (b) determined pursuant to a formula rate set forth in Attachment H, both as adjusted in accordance with this 
section (11)(A). 
SZPL is the sum of each Zone’s annual peak load (in kW) plus the peak day firm reservations for Point-to-Point service at the Border of PJM (in kW) subject to the 
charges set forth in section (1) herein (prior to any applicable discount) from the most recently completed 12-month period ending October 31.
(ii) Where the Revenue Requirement of a Transmission Owner is determined pursuant to a formula rate: 
(a) the Revenue Requirement shall be increased by the amount of any revenue included in the Transmission Owner’s formula rate as credits in 
determining the Revenue Requirement for Network Integration Transmission Service from: (i) Transmission Enhancement Charges; (ii) Firm Point-to-Point 
Transmission Service charges under Schedule 7; or (iii) Network Integration Transmission Service to Non-Zone Network Load under Attachment H-A; (iv) 
Interconnection Reliability Reinforcement Charges;  or (v) Generator Reliability Reinforcement Recovery Fees that are included in the Transmission Owner’s 
formula rate as revenue credits in determining the Revenue Requirement for Network Integration Transmission Service, if such credits are identified in the 
Transmission Owner’s formula rate annual update; and
Page 82

PDF page 248

(b)  (I) the Revenue Requirement shall be reduced by the amount of any credit applied directly to Network Customers to offset the cost of Network 
Integration Transmission Service, including credits to Network Customers resulting from: (i) a Network Upgrade Funding Agreement, Tariff, Attachment O-2; (ii) a 
State Agreement Public Policy Project subject to Tariff, Schedule 12, section (b)(xii)(B);  (iii) agreements for transmission service entered into prior to a 
Transmission Owner signing the Consolidated Transmission Owners Agreement or any of its predecessor agreements or (iv) an entity executing an agreement by 
which such entity is obligated to pay for some, or all, of the Revenue Requirement of Transmission Facilities for which Network Customers would otherwise be 
responsible. (II) The Revenue Requirement for inclusion in the SHRR shall not be reduced by the amount of any credits for (i) Transmission Enhancement Charges; 
(ii) Firm Point-to-Point Transmission Service charges under this Schedule 7; or (iii) Network Integration Transmission Service to Non-Zone Network Load under 
Tariff, Attachment H-A; (iv) Interconnection Reliability Reinforcement Charges;  or (v) Generator Reliability Reinforcement Recovery Fees.
(B) The Transmission Provider shall update the Border Yearly Charge annually based on the Revenue Requirements for each Transmission Owner used to 
determine charges for Network Integration Transmission Service in effect on January 1, provided that such Revenue Requirements were approved by FERC, stated in a 
formula rate update informational filing with FERC, or posted on the Transmission Provider’s website no later than the preceding October 31.  The Border Yearly Charge 
so updated shall become effective as of January 1 and remain in effect for the remainder of the calendar year.  Except as provided in subsection (D) of this section (11), any 
change to the data used to determine the Border Yearly Charge following October 31, including any change in the number or identity of Transmission Owners filing 
Revenue Requirements for Network Integration Transmission Service under Attachment H, shall not be reflected in Border Yearly Charge until the next annual update.
(C) Not later than the first Business Day of December each year, the Transmission Provider shall post on the Transmission Provider’s website a “BYC Workbook” 
that shall include (1) all of the inputs and calculations used to determine the Border Yearly Charge, (2) references to the sources of the inputs used to determine the Border 
Yearly Charge from each Transmission Owner’s stated or formula rate filing or posting, (3) a variance report detailing all changes to the calculations, inputs, or procedures 
used to determine the proposed Border Yearly Charge as compared to the calculations, inputs or procedures used to determine the Border Yearly Charge then in effect, and 
(4) contact information for the submission of inquiries or comments regarding the posted BYC Workbook.  All inputs used to determine the SHRR must be taken either 
from a stated Revenue Requirement for Network Integration Transmission Service specified in Attachment H or from an identified entry in a Transmission Owner’s 
formula rate update either filed with the FERC or posted on the Transmission Provider’s website for the rate for Network Integration Transmission Service that will be in 
effect on January 1.  
(D)  Procedure for Review of and Challenge to the Border Yearly Charge Determination.
(i)  Review of the Border Yearly Charge Determination.
Page 83

PDF page 249

(a)  Within sixty (60) days of the posting of the BYC Workbook, Interested Parties, including entities with existing, requested or planned 
transmission service reservations for service at the Border of PJM (“Border Rate Transmission Customers”), state utility regulatory commissions, consumer advocacy 
agencies, state attorneys general, and any entity having standing under Section 206 of the Federal Power Act (“Interested Party”), may submit reasonable information 
requests to the Transmission Provider regarding its selection and use of inputs and the calculations performed in calculating the Border Yearly Charge, including the 
creation of the BYC Workbook, with respect to any adjustments made by the Transmission Provider, including adjustments made based on information provided by a 
Transmission Owner to the Transmission Provider:  (1) to a Transmission Owner’s Revenue Requirement for Network Integration Transmission Service prior to its 
inclusion as an input into the calculation of the SHRR for the Border Yearly Charge; (2) to the data used in determining SZPL; (3) to the Revenue Requirement of a 
Transmission Owner in determining the Border Yearly Charge made in accordance with Section (11)(A)(ii); and (4) in response to any FERC orders approving or requiring 
changes to, or refunds associated with, a Transmission Owner’s formula rate or resulting annual Revenue Requirement.
(b)  The Transmission Provider shall respond to such reasonable information requests as soon as practicable, but no later than within forty-five (45) 
days of the receipt of the information request, unless it determines that additional time is required to respond.  The Transmission Provider shall post any information 
requests received and its responses thereto on the Transmission Provider’s website, provided that any responsive information that has been designated by a Transmission 
Owner as confidential pursuant to the provisions of the Operating Agreement or Consolidated Transmission Owners Agreement shall not be posted and shall be handled 
solely in accordance with such provisions.  An Interested Party may request a meeting with the Transmission Provider and any interested Transmission Owner to discuss 
any response to an information request or any dispute regarding the calculation of the Border Yearly Charge annual update. The Transmission Provider and any interested 
Transmission Owner shall exercise good faith in responding to an Interested Party’s meeting request and shall not unreasonably deny or delay such meeting in a manner 
that prejudices an Interested Party’s opportunity to timely review the Border Yearly Charge annual update.
(c)  At any time after posting of the BYC Workbook, but before a challenge pursuant to section (11)(D)(ii) (“Challenge”) is filed, at the request of an 
Interested Party, the Transmission Provider will be required to meet with the Interested Party within ten (10) Business Days of such request in an attempt to resolve any 
dispute regarding the calculation of the Border Yearly Charge raised by the Interested Party in its meeting request. If the dispute relates to information from one or more 
Transmission Owners’ Tariff, Attachment H stated or formula rate or Zonal peak load determination, the relevant Transmission Owner(s) will be notified by the 
Transmission Provider of the dispute and will be permitted to attend the meeting.
(d)  If it is determined that the Border Yearly Charge is based on an incorrect input or calculation or FERC directs that a Transmission Owner’s
Revenue Requirement, upon which the Border Yearly Charge is based, be changed and implemented as a change to the Transmission Owner’s rate for Network Integration 
Transmission Service at a time other than provided for in the Transmission Owner’s formula rate protocols (“Changed Revenue Requirement”), the Transmission Provider 
shall change the   Border Yearly Charge as necessary to account for such Changed Revenue Requirement and post on the Transmission Provider’s website a revised BYC 
Workbook documenting the changes to the Border Yearly Charge to incorporate the correction or change. The correction to the Border Yearly Charge shall take effect no 
Page 84

PDF page 250

later than the first day of the month that begins 30 days after a correction is posted by the Transmission Provider or, if the correction or Changed Revenue Requirement 
results from a FERC order, on a schedule consistent with that order. Subject to the notice of correction described above, to the extent permitted by Tariff, Part I, section 
10.4, PJM Settlement, on behalf of itself or as agent for the Transmission Provider, shall adjust the charges to Border Rate Transmission Customers with respect to any 
month prior to the effective date of the Changed Revenue Requirement being reflected in the Border Yearly Charge that is affected by the correction or Changed Revenue 
Requirement and refund or credit any amount paid in excess of the corrected Border Yearly Charge. Any correction under this subsection (D) shall be limited to any 
Changed Revenue Requirement and the Transmission Provider’s selection and use of Border Yearly Charge inputs and the calculations necessary to determine the Border 
Yearly Charge. This section does not apply to a FERC order that changes a Transmission Owner’s Revenue Requirement that is implemented through a true-up mechanism.
(e) If FERC issues an order directing or approving refunds associated with a Transmission Owner’s Revenue Requirement that previously was, or 
currently is, incorporated into the SHRR to be paid to Network Integration Transmission Service customers, Border Rate Transmission Customers shall also receive a 
refund, to the extent that the changes in a Transmission Owner’s Revenue Requirement upon which such refund is based affects the calculation of the Border Yearly 
Charge.
(f)  Nothing in section (11) shall authorize an inquiry into the data or information filed or posted by a Transmission Owner as part of its transmission 
rate protocols pursuant to Tariff, Attachment H, or shall affect the rights that any Border Rate Transmission Customer may have under said protocols.
(ii)  Challenge to the Border Yearly Charge Determination.
(a)  An Interested Party may file with FERC a Challenge to the annual update of the Border Yearly Charge within  ninety (90) days of the posting of 
the BYC Workbook or thirty (30) days of receiving a response to any information request it submitted under subsection (11)(D)(i)(a), whichever is later.  Any such 
Challenge shall be served on Transmission Provider and each Transmission Owner with Revenue Requirements included in the BYC Workbook.
(b)  A Challenge must specify and include adequate supporting documentation, detailing how the Transmission Provider’s selection of inputs to or 
calculation of the Border Yearly Charge fails to comply with the provisions of this Schedule 7, section (11), identifying any input data or other BYC Workbook entry that is 
alleged to be missing or inaccurate or the Border Yearly Charge calculations alleged to be performed incorrectly.
(c)  A Challenge must be limited to the Transmission Provider’s selection and use of Border Yearly Charge inputs and the calculations necessary to 
determine the Border Yearly Charge and may not seek to modify Tariff, Schedules 7 and 8 or Attachment H-A or question the data or information filed or posted by a 
Transmission Owner pursuant to Tariff, Attachment H. 
Page 85

PDF page 251

(d)  The Transmission Provider and each Transmission Owner with Revenue Requirements included in the BYC Workbook shall have thirty (30) 
days to answer a Challenge.
(e)  In any proceeding before the FERC in response to a Challenge, the Transmission Provider shall bear the burden, consistent with Section 205 of 
the FPA, of demonstrating that it has correctly applied the terms of this Schedule 7, section (11).
(E) When the Transmission Provider posts on its website a Border Yearly Charge annual update under subsection (C) or correction under subsection (D) of this 
section (11), it shall also make an informational filing with the FERC that includes such posting.
(F) A Transmission Customer taking Point-to-Point Transmission Service at the Border of PJM under this Schedule 7, including any discounted service pursuant to 
Section (3), is relieved from, and shall not be separately allocated or assigned Transmission Enhancement Charges under Schedule 12 §(c)(5) on the basis of its reservation 
of Firm Point-to-Point Transmission Service at the Border of PJM.  Payment of the charges set forth in this Schedule does not relieve the responsibility of a Transmission 
Customer or Merchant Transmission Facility to pay Transmission Enhancement Charges assigned to such Merchant Transmission Facility, other than pursuant to Tariff, 
Schedule 12, §(c)(5), nor does it determine other cost obligations of Transmission Customers or Merchant Transmission Facilities that may be imposed under other 
provisions of the Tariff.  
(G)  Point-to-Point Transmission Service at the Border of PJM includes service to a Point of Delivery at a Merchant Transmission Facility that provides service to a 
neighboring transmission system.
(H)  Customers taking Point-to-Point Transmission Service at the Border of PJM with a Point of Delivery at a Merchant Transmission Facility and not receiving a 
discount from the Border Yearly Charge pursuant to this Schedule 7, section (3) under the settlement entered into in FERC Docket No. ER19-2105, shall receive a credit 
determined in accordance with the following formula:
MTFC = BYC*MTFTEC/SHRR
Where:
MTFC is the credit to the Border Yearly Charge per kW of reserved capacity; 
BYC is the Border Yearly Charge;
Page 86

PDF page 252

MTFTEC is the total annual Transmission Enhancement Charges under Tariff, Schedule 12 applicable to the Merchant Transmission Facility to which the customer 
is taking Point-to-Point Transmission Service during the current calendar year; and 
SHRR is the amount determined pursuant to subsection (A) of this section (11).
The MTFC shall be credited on a monthly basis only for those months during which the customer takes Firm Point-to-Point Transmission Service to the Merchant 
Transmission Facility.
Page 87

PDF page 253

SCHEDULE 12
Transmission Enhancement Charges and 
Interconnection Reliability Reinforcement Cost Recovery
(a)
Establishment of Transmission Enhancement Charges.  
(i)
Establishment of Transmission Enhancement Charges by Transmission 
Owners and Entities That Will Become Transmission Owners.  One or more of the 
Transmission Owners may be designated to construct and own and/or finance Required 
Transmission Enhancements by (1) the Regional Transmission Expansion Plan periodically 
developed pursuant to Operating Agreement, Schedule 6 or (2) any joint planning or 
coordination agreement between PJM and another region or transmission planning authority set 
forth in Tariff, Schedule 12-Appendix B (“Appendix B Agreement”) (collectively, for purposes 
of this Schedule 12 only, “Regional Transmission Expansion Plan”).  Operating Agreement, 
Schedule 6, section 1.7 recognizes that Transmission Owners, subject to obtaining any necessary 
regulatory approvals, may seek to recover the costs of Required Transmission Enhancements and 
obligates PJMSettlement to collect on behalf of Transmission Owner(s) any charges established 
by Transmission Owners to recover the costs of Required Transmission Enhancements.  If a 
Transmission Owner is designated by the Regional Transmission Expansion Plan to construct 
and own and/or finance a Required Transmission Enhancement, such Transmission Owner may 
choose any of the following cost recovery mechanisms, subject to the crediting procedures set 
forth in section (e) below: 
(1)
Decline to seek to recover the costs of Required Transmission Enhancements 
from customers until such time as it makes a filing pursuant to Section 205 of the Federal 
Power Act to revise its Network Integration Transmission Service rates;
(2) 
Make a filing pursuant Section 205 of the Federal Power Act and the FERC’s 
rules and regulations to establish the revenue requirement with respect to a Required 
Transmission Enhancement, without filing to revise its rates for Network Integration 
Transmission Service generally; or
(3) 
Establish the revenue requirement with respect to a Required Transmission 
Enhancement through the operation of a formula rate in effect applicable to its rates for 
Network Integration Transmission Service.
A charge established to recover the revenue requirement with respect to a Required Transmission 
Enhancement is hereafter referred to as a “Transmission Enhancement Charge.”  Transmission 
Enhancement Charges of one or more Transmission Owners for Required Transmission 
Enhancements shall be established in accordance with this Schedule 12.   
(ii)
Establishment of Transmission Enhancement Charges With Respect to 
Required Transmission Enhancements Constructed by Entities in Another Region. The 
revenue requirement with respect to a Required Transmission Enhancement constructed pursuant 
to an Appendix B Agreement in another region by an entity designated by such other region shall 
be governed by the tariffs or agreements in effect in such region. Transmission Enhancement 
Page 88

PDF page 254

Charges to recover the costs of such Required Transmission Enhancement for which PJM is 
responsible shall be determined in accordance with this Schedule 12.  Other than with respect to 
a Required Transmission Enhancement constructed pursuant to an Appendix B Agreement, no 
PJM Network or Transmission Customer will bear cost responsibility for any required 
transmission upgrades in another region as a consequence of a Required Transmission 
Enhancement included in the Regional Transmission Expansion Plan.  
(iii)
Transmission Facilities Not Eligible for Cost Responsibility Assignment.  Any 
alternating current (“A.C.”) facilities or direct current (“D.C.”) facilities that are Attachment 
Facilities, Local Upgrades, Merchant Network Upgrades, Merchant Transmission Facilities, 
Network Upgrades, Supplemental Projects, or any other Transmission Facilities that operate or 
are planned to be operated in a manner that requires customers to subscribe to transmission 
service over such facilities or to a portion of the electric capability of such facilities shall not be 
eligible for cost responsibility assignment pursuant to this Schedule 12.  
(iv)
Entities Not Yet Eligible to Become Transmission Owners.  For purposes of 
this Schedule 12 only, the term, “Transmission Owner,” shall include any entity that undertakes 
to construct and own and/or finance a Required Transmission Enhancement pursuant to a 
designation in the Regional Transmission Expansion Plan to construct and own and/or finance 
such Required Transmission Enhancement, even if such entity is not yet eligible to become a 
party to the Consolidated Transmission Owners Agreement.  Nothing in the PJM Tariff nor the 
Consolidated Transmission Owners Agreement shall prevent an entity that undertakes to 
construct and own and/or finance a Required Transmission Enhancement pursuant to a 
designation in the Regional Transmission Expansion Plan to construct and own and/or finance 
such Required Transmission Enhancement from recovering the costs of such Required 
Transmission Enhancement through this Schedule 12.
(v)
Effective Date.  The assignment of cost responsibility or classification of 
Required Transmission Enhancements either (1) made by the Transmission Provider prior to 
February 1, 2013, or (2) applicable to Required Transmission Enhancements approved by the 
PJM Board pursuant to Operating Agreement, section 1.6 prior to February 1, 2013 are set forth 
in Tariff, Schedule 12-Appendix.  Except as specifically set forth herein, nothing in this 
Schedule 12 shall change the assignment of cost responsibility or classification of Required 
Transmission Enhancements included in Tariff, Schedule 12-Appendix.  The assignment of cost 
responsibility or classification of all other Required Transmission Enhancements shall be set 
forth in Tariff, Schedule 12-Appendix A. 
(b)
Designation of Customers Subject to Transmission Enhancement Charges.  
(i)
Regional Facilities and Necessary Lower Voltage Facilities.  Transmission 
Provider shall assign cost responsibility on a region-wide basis for Required Transmission 
Enhancements included in the Regional Transmission Expansion Plan that (1) (a) are A.C. 
facilities that operate at or above 500 kV; (b) constitute a single Required Transmission 
Enhancement comprising two A.C. circuits operating at or above 345 kV and below 500 kV, 
where both circuits originate from a single substation or switching station at one end and 
Page 89

PDF page 255

terminate at a single substation or switching station at the other end, regardless of whether or not 
the two circuits are routed in the same right-of-way (“Double-circuit 345 kV Required 
Transmission Enhancement”); (c) are A.C. or D.C. shunt reactive resources (such as capacitors, 
static var compensators, static synchronous condenser (STATCON), synchronous condensers, 
inductors, other shunt devices, or their equivalent) connected to a Transmission Facility 
described in clause (a) or (b) of this subsection, or (d) are D.C. facilities meeting the criteria set 
forth in subsection (b)(i)(D) (collectively, “Regional Facilities”), or (2) new A.C. Transmission 
Facilities or expansions or enhancements to existing Transmission Facilities that operate below 
500 kV (or 345 kV in the case of a Regional Facility described in clause (1)(b) of this 
subsection) or new D.C. Transmission Facilities that do not meet the criteria of subsection 
(b)(i)(D) that must be constructed or strengthened to support new Regional Facilities, based on 
the planning criteria used by the Transmission Provider in developing the applicable Regional 
Transmission Expansion Plan (“Necessary Lower Voltage Facilities”) as follows: 
(A)
Cost responsibility for Regional Facilities and Necessary Lower Voltage 
Facilities shall be allocated among Responsible Customers as defined in this Schedule 12 as 
follows:
(1)
Fifty percent (50%) shall be assigned annually on a load-ratio 
share basis as follows:
(a)
With respect to each Zone, using, consistent with Tariff, 
Part III, section 34.1, the applicable zonal loads at the time of such Zone’s annual peak load from 
the 12-month period ending October 31 preceding the calendar year for which the annual cost 
responsibility allocation is determined; and
(b)
With respect to Merchant Transmission Facilities, (1) for 
the calendar year following the year in which it initiates operation, the actually awarded Firm 
Transmission Withdrawal Rights associated with its existing Merchant Transmission Facility; 
and (2) for all subsequent calendar years, the annual peak load of the Merchant Transmission 
Facility (not to exceed its actual Firm Transmission Withdrawal Rights) from the 12-month 
period ending October 31 of the calendar year preceding the calendar year for which the annual 
cost responsibility allocation is determined.
(2)
Fifty percent (50%) shall be assigned as follows:
(a)
In the case of a Required Transmission Enhancement 
included in the Regional Transmission Expansion Plan to address one or more reliability 
violations or to address operational adequacy and performance issues (collectively, “Reliability 
Project”), in accordance with the distribution factor (“DFAX”) analysis described in subsection 
(b)(iii) or the analysis applicable to Regional Facilities that address stability issues described in 
subsection (b)(xviii) of this Schedule 12 as applicable; and
(b)
In the case of a Required Transmission Enhancement 
included in the Regional Transmission Expansion Plan to relieve one or more economic 
constraints as described in Operating Agreement, Schedule 6, section 1.5.7(b)(iii) (“Economic 
Page 90

PDF page 256

Project”), in accordance with the methodology described in subsection (b)(v) of this Schedule 
12.
(B)
(1) Except for transformers that are an integral component of a Regional 
Facility, transformers connected to Lower Voltage Facilities, as defined in section (b)(ii) of this 
Schedule 12, shall not be considered Regional Facilities or Necessary Lower Voltage Facilities; 
and (2) Transmission Facilities that are not Regional Facilities and deliver energy from a 
Regional Facility to load shall not be considered Necessary Lower Voltage Facilities.
(C)
With respect Required Transmission Enhancements that qualify as 
Regional Facilities under subsection (b)(i)(1)(b) or subsection (b)(i)(D)(2) of this Schedule 12:
(1)
where the Required Transmission Enhancement includes both new 
Transmission Facilities and pre-existing Transmission Facilities, cost responsibility under this 
section (b)(i) shall apply only to the cost of the new Transmission Facilities plus the original cost 
less accumulated depreciation of pre-existing Transmission Facilities that are included in Tariff, 
Schedule 12-Appendix or Tariff, Schedule 12-Appendix A;
(2)
cost responsibility shall be assigned under this section (b)(i) only 
after the Required Transmission Enhancement goes into service as a Double-circuit 345 kV 
Required Transmission Enhancement or a Double-circuit D.C. Required Transmission 
Enhancement; and 
(3)
cost responsibility shall be assigned under this section (b)(i) for 
any CWIP permitted to be recovered before the Required Transmission Enhancement goes into 
service only after such Transmission Facilities are approved in a Regional Transmission 
Expansion Plan as a Double-circuit 345 kV Required Transmission Enhancement or a Double-
circuit D.C. Required Transmission Enhancement.
(D)
A Required Transmission Enhancement included in the Regional 
Transmission Expansion Plan that is a D.C. facility, consisting of D.C. lines (i.e., wires or 
cables) and A.C./D.C. converters, shall be a Regional Facility only if: 
(1) 
such D.C. facility comprises two poles and operates at a voltage of 
±433 kV D.C. or above; or
(2)
such D.C. Facility constitutes a single Required Transmission 
Enhancement comprising two D.C. circuits where (i) both circuits originate from a single 
substation or switching station at one end and terminate at a single substation or switching 
station at the other end, regardless of whether or not both circuits are routed in the same right-of-
way, and (ii) each such circuit consists of two poles and operates at a voltage of ±298 kV D.C or 
above (“Double-circuit D.C. Required Transmission Enhancement”).
(ii)
Lower Voltage Facilities.  Transmission Provider shall assign cost responsibility 
for Required Transmission Enhancements that (a) are not Regional Facilities; and (b) are not 
“Necessary Lower Voltage Facilities” as defined in section(b)(i) of this Schedule 12 (collectively 
“Lower Voltage Facilities”), as follows:
Page 91

PDF page 257

(A)
If the Lower Voltage Facility is a Reliability Project,  Transmission 
Provider shall use the DFAX analysis described in subsection (b)(iii) or the analysis applicable to 
Regional Facilities that address stability issues described in subsection (b)(xviii) of this Schedule 
12 as applicable; and
(B)
If the Lower Voltage Facility is an Economic Project, Transmission 
Provider shall use the methodology described in subsection (b)(v) of this Schedule 12.
(iii)
DFAX Analysis for Reliability Projects.  
(A)  For purposes of the assignment of cost responsibility for Reliability Projects 
under subsection (b)(i)(A)(2)(a) and subsection (b)(ii)(A) of this Schedule 12, the Transmission 
Provider, based on a computer model of the electric network and using power flow modeling 
software, shall calculate distribution factors, represented as decimal values or percentages, which 
express the portions of a transfer of energy from a defined source to a defined sink that will flow 
across a particular transmission facility or group of transmission facilities.  These distribution 
factors represent a measure of the use by the load of each Zone or Merchant Transmission 
Facility (collectively, “Responsible Zone”) of the Required Transmission Enhancement, as 
determined by a power flow analysis.  In general, a distribution factor can be represented as:
Distribution Factor = (After-shift power flow – pre-shift power flow) / Total amount of power 
shifted
Total amount of power shifted = Modeled incremental megawatt transfer to a given Load 
Deliverability Area or Merchant Transmission Facility
Pre-shift power flow = Megawatt flow over the Required Transmission Enhancement  
before the incremental megawatt transfer
After-shift power flow = Megawatt flow over the Required Transmission Enhancement 
after the incremental megawatt transfer
When calculating such distribution factors:
(1)
All distribution factors are calculated with respect to the Required 
Transmission Enhancement subject to cost allocation under subsection (b)(i)(A)(2)(a) and 
subsection (b)(ii)(A) of this Schedule 12.
(2)
The calculation of distribution factors shall be determined using 
linear matrix algebra, such that distribution factors represent the ratio of (i) a change in megawatt 
flow on a Required Transmission Enhancement to (ii) a change in megawatts transferred to 
aggregate load within a Zone or, in the case of a Merchant Transmission Facility, the point of 
withdrawal associated with Firm Transmission Withdrawal Rights over such Merchant 
Transmission Facility.
Page 92

PDF page 258

(3)
With respect to a Merchant Transmission Facility, zonal peak load 
shall mean (i) the existing Firm Transmission Withdrawal Rights of the Merchant Transmission 
Facility being evaluated, if the Merchant Transmission Facility is in service, or (ii) for a 
Merchant Transmission Facility that is not yet in service, the planned Firm Transmission 
Withdrawal Rights of the Merchant Transmission Facility being evaluated as identified in the 
Interconnection Service Agreement in effect for such Merchant Transmission Facility. 
(4)
In the DFAX analysis, when Transmission Provider models a 
transfer from generation to all load within an individual Zone, Transmission Provider shall 
model the transfer to the Zone as a whole (not on a bus-by-bus basis).  
(5)
In the DFAX analysis, Transmission Provider shall model 
generation both external and internal to individual Responsible Zones to reflect (a) the 
boundaries of Locational Deliverability Areas (“LDAs”), and (b) limitations with respect to the 
reliability objective for moving generation capacity across the transmission system.  
Transmission Provider shall adopt the Capacity Emergency Transfer Objective (“CETO”), 
associated with that LDA and calculated for the applicable planning year to be the transfer 
limitation into the LDA.  In modeling the system generation and load, Transmission Provider 
shall assume that the percentage of the zonal load in the LDA served by external (or internal) 
generation to the LDA shall equal the ratio of (i) the CETO associated within that LDA (or 
generation internal with the LDA) to (ii) the sum of (a) the internal generation within the LDA 
and (b) the CETO associated with that LDA.  For the generation dispatch used in calculating the 
distribution factor, Transmission Provider shall distribute these amounts of external/internal 
generation among all generation in the PJM Region external to/internal within the LDA, 
respectively, in proportion to their capacity.  For Responsible Zones that are located within 
LDAs that are also entirely contained in other larger LDAs, the modeling approach and 
distribution factor calculations shall be repeated for such Responsible Zones for each LDA.  The 
lowest distribution factor derived from these calculations shall be applied to the Responsible 
Zone in the calculation of the use of the Required Transmission Enhancement.  
(B) 
The DFAX analysis will be performed in accordance with the following 
steps:
(1)
Transmission Provider shall calculate a distribution factor and a 
direction of use for each Responsible Zone by modeling a transfer from all generation in the PJM 
Region to each Responsible Zone.  To establish the use by a Responsible Zone, in megawatts, of 
a Required Transmission Enhancement, the distribution factor of a Required Transmission 
Enhancement associated with the resulting transfer modeled by the Transmission Provider to 
each Responsible Zone shall be multiplied by the Responsible Zone’s peak load.
(2)
The Transmission Provider shall separately determine the relative 
use of the Required Transmission Enhancement by each Responsible Zone in each direction by 
dividing the megawatts of use by each Responsible Zone determined in section (iii)(B)(1) above 
Page 93

PDF page 259

by the total use of all Responsible Zones using the Required Transmission Enhancement in the 
same direction of use.
(3) 
Transmission Provider shall determine the direction of use 
percentage of the Required Transmission Enhancement in each direction using a production cost 
analysis to determine the total use, in megawatt-hours, of the Required Transmission 
Enhancement by all Zones and Merchant Transmission Facilities in each direction over the 
course of a year.  The Transmission Provider shall calculate the percentage use in each direction 
by dividing the megawatt-hours of use in each direction by total use in megawatt-hours in both 
directions of use.
(4)
The Transmission Provider shall multiply the relative use by each 
Responsible Zone of the Required Transmission Enhancement in each direction of use 
determined in section (iii)(B)(2) above, by the applicable direction of use percentage determined 
in section (iii)(B)(3) above. 
(5)
The products of the calculation performed in section (iii)(B)(4) 
above, shall determine the relative allocation to each Responsible Zone of cost responsibility for 
the Required Transmission Enhancement.
(C)
In the DFAX analysis, the Zones of Public Service Electric and Gas 
Company and Rockland Electric Company will be treated as one Zone unless and until Rockland 
Electric Company elects to be treated as a separate Zone in accordance with the terms of the 
Settlement Agreement And Offer Of Partial Settlement approved by FERC in Docket Nos. 
ER06-456-000, et al.
(D)
Transmission Provider shall round cost responsibility assignments 
determined using the DFAX analysis described in subsection (b)(iii) of this Schedule 12 to the 
nearest one-hundredth of one percent.
(E)
Transmission Provider shall not account for the ability to adjust use of 
phase angle regulators (“PARs”) in the DFAX analysis described in subsection (b)(iii) of this 
Schedule 12.  In the DFAX analysis, all PAR angles shall be fixed at their base case settings. 
(F)
In the DFAX analysis, if the Required Transmission Enhancement is a 
D.C. facility, the Transmission Provider shall determine cost responsibility assignment as 
follows:
(1)
The Required Transmission Enhancement shall be replaced in the 
model with a comparable proxy A.C. facility, the impedance of which shall be calculated based 
on the length of the D.C. facility that was removed from the model multiplied by an approximate 
per unit/mile impedance value for the proxy A.C. facility.
(2)
Where a D.C. facility is an integral part of a Required 
Transmission Enhancement that also includes A.C. facilities, the methodology described in 
Page 94

PDF page 260

subsection (b)(iii)(F)(1) above shall be used only for the D.C. facility segment of such Required 
Transmission Enhancement.
(3)
A D.C. facility used to control flow over portions of the 
Transmission System shall be modeled with a zero impedance and no control shall be applied.
(G)
If Transmission Provider determines in its reasonable engineering judgment 
that, as a result of applying the provisions in section (b)(iii) of this Schedule 12, the DFAX 
analysis cannot be performed or that the results of such DFAX analysis are objectively 
unreasonable, the Transmission Provider may use an appropriate substitute proxy for the 
Required Transmission Enhancement in conducting the DFAX analysis.  If a proxy is used that is 
not specified in this Schedule 12, Transmission Provider shall state in a written report (a) the 
reasons why it determined the DFAX analysis could not be performed or that the results of the 
DFAX analysis were objectively unreasonable; (b) why the substitute proxy produced 
objectively reasonable results; and (3) a recommendation as to what changes, if any, should be 
considered in conducting the DFAX analysis.
(H)
The Transmission Provider shall make a preliminary cost responsibility 
determination for each Required Transmission Enhancement subject to section (b)(iii) of this 
Schedule 12 at the time such Required Transmission Enhancement is included in the Regional 
Transmission Expansion Plan.  
(1) 
When CWIP in connection with a Required Transmission 
Enhancement subject to this section (b)(iii) of this Schedule 12 is entitled to be recovered, the 
preliminary determination of cost responsibility made at the time that the Required Transmission 
Enhancement was included in the Regional Transmission Expansion Plan shall be used to assign 
cost responsibility for such CWIP and such cost responsibility shall remain unchanged until the 
date the Required Transmission Enhancement goes into service.  Once a Required Transmission 
Enhancement has gone into service, the updated cost responsibility determination provided for in 
subsection (b)(iii)(H)(2) below shall apply.
(2)
Beginning with the calendar year in which a Required 
Transmission Enhancement is scheduled to enter service, and thereafter annually at the 
beginning of each calendar year, the Transmission Provider shall update the preliminary cost 
responsibility determination for each Required Transmission Enhancement using the values and 
inputs used in the base case of the most recent Regional Transmission Expansion Plan approved 
by the PJM Board prior to the date of the update.  All values and inputs used in the calculation of 
the distribution factor in a determination of cost responsibility shall be the same values and 
inputs as used in the base case of the most recent Regional Transmission Expansion Plan 
approved by the PJM Board prior to the determination of cost responsibility.  
(iv)
Spare Parts, Replacement Equipment And Circuit Breakers.  Transmission 
Provider shall assign cost responsibility for spare parts, replacement equipment, and circuit 
breakers and associated equipment, included in the Regional Transmission Expansion Plan as 
follows:
Page 95

PDF page 261

(A)
Spare parts that are part of the design specifications of a Required 
Transmission Enhancement at the time such Required Transmission Enhancement is first 
included in the Regional Transmission Expansion Plan shall be considered part of the Required 
Transmission Enhancement for the purpose of applying the cost threshold described in 
subsection (b)(vi) of this Schedule 12 and cost responsibility for such spare parts shall be 
assigned in the same manner as the Required Transmission Enhancement.  Cost responsibility for 
spare parts independently included the Regional Transmission Expansion Plan and not a part of 
the design specifications of a Required Transmission Enhancement as described above in this 
subsection shall be assigned to the Zone of the owner of the spare part, if the owner of the spare 
part is a Transmission Owner listed in Tariff, Attachment J.  If the owner of the spare part is not 
a Transmission Owner listed in Tariff, Attachment J, cost responsibility shall be assigned on a 
pro rata basis to the zones that bear cost responsibility for the owner’s Required Transmission 
Enhancements.
(B)
Replacement equipment that is part of the design specifications of a 
Required Transmission Enhancement at the time the Required Transmission Enhancement is first 
included in the Regional Transmission Expansion Plan shall be considered part of the Required 
Transmission Enhancement for the purpose of applying the cost threshold described in section 
(b)(vi) of this Schedule 12 and cost responsibility for such replacement equipment shall be 
assigned in the same manner as the Required Transmission Enhancement. Cost responsibility for 
Required Transmission Enhancement replacement equipment independently included in the 
Regional Transmission Expansion Plan and not a part of the design specifications of a Required 
Transmission Enhancement as described above in this subsection, shall be assigned to the same 
Zones and/or Merchant Transmission Facilities and in the same proportions as the then-existing 
assignments of cost responsibility for the facilities that the replacement equipment is replacing.
(C)
Circuit breakers and associated equipment that are part of the design 
specifications of a Required Transmission Enhancement at the time the Required Transmission 
Enhancement is first included in the Regional Transmission Expansion Plan shall be considered 
part of the Required Transmission Enhancement for the purpose of applying the cost threshold 
described in subsection (b)(vi) of this Schedule 12 and cost responsibility for such circuit 
breakers and associated equipment shall be assigned in the same manner as the Required 
Transmission Enhancement.  Cost responsibility for circuit breakers and associated equipment 
independently included in the Regional Transmission Expansion Plan and not a part of the design 
specifications of a transmission element of a  Required Transmission Enhancement as described 
above in this subsection, shall be assigned to the Zone of the owner of the circuit breaker and 
associated equipment if the owner of the circuit breaker is a Transmission Owner listed in Tariff, 
Attachment J.  If the owner of the circuit breaker is not a Transmission Owner listed in Tariff, 
Attachment J, cost responsibility shall be assigned on a pro rata basis to the zones that bear cost 
responsibility for the owner’s Required Transmission Enhancements. 
(v)
Economic Projects.  Transmission Provider shall assign (i) fifty percent (50%) of 
cost responsibility for Economic Projects that are Regional Facilities; and (ii) full cost 
responsibility for Economic Projects that are Lower Voltage Facilities; as follows:
Page 96

PDF page 262

(A)
Transmission Provider shall assign cost responsibility for Economic 
Projects that are accelerations of Reliability Projects as described in Operating Agreement, 
Schedule 6, section 1.5.7(b)(i) (“Acceleration Projects”) by performing and comparing (1) a 
DFAX analysis consistent with the methodology described in subsection (b)(iii) of this Schedule 
12, and (2) a methodology that is intended to act as a proxy for expected economic benefits from 
reduced Locational Marginal Prices (“LMP Benefit”) over the period that the reliability-based 
enhancement or expansion is to be accelerated (“LMP Benefits Methodology”).  The LMP 
Benefits Methodology shall determine cost responsibility assignment percentages to Zones and 
Merchant Transmission Facilities in the following manner.  The LMP Benefit to a Zone shall be 
deemed to be equal to the reduction in Locational Marginal Price payments made by Load 
Serving Entities as a result of the Acceleration Project assuming the customers purchase all 
energy needs from the PJM Interchange Energy Market, and LMP Benefits so calculated shall be 
converted into percentage cost responsibility assignments for the affected Zones.  The LMP 
Benefits Methodology shall not incorporate the financial effects of allocations of Auction 
Revenue Rights or Financial Transmission Rights.  The LMP Benefit to a Merchant 
Transmission Facility shall be deemed to be equal to the proportionate share of assigned cost 
responsibility using the DFAX analysis and the assignments of cost responsibility to other Zones 
in the LMP Benefits Methodology shall be proportionately adjusted, as necessary, to reflect this 
treatment of Merchant Transmission Facilities to ensure that the total allocation for any 
economic-based Required Transmission Enhancement equals one hundred percent.  If, after 
performing both analyses and comparing the percentage cost responsibility assignments for the 
affected Zones calculated pursuant to the DFAX analysis and the LMP Benefits Methodology, 
the results do not indicate at least a ten percentage point cost responsibility assignment 
differential between the two methods for any Zone, cost responsibility for the Acceleration 
Project shall be assigned using the DFAX analysis.  If, after performing both analyses and 
comparing the percentage cost responsibility assignments for the affected Zones calculated 
pursuant to the DFAX analysis and LMP Benefits Methodology, the results indicate at least a ten 
percentage point cost responsibility assignment differential between the DFAX analysis and the 
LMP Benefits Methodology for any Zone, cost responsibility for the Acceleration Project for the 
period of time the Reliability Project is accelerated (i.e. the period between the date the 
Reliability Project actually goes into service and the date the Reliability Project originally was 
scheduled to go in service in the PJM Board approved Regional Transmission Expansion Plan) 
shall be assigned using the LMP Benefits Methodology.  For all periods other than the period of 
time the Reliability Project is accelerated, cost responsibility for such an Acceleration Project 
shall be assigned in accordance with the provisions of this Schedule 12 governing the assignment 
of cost responsibility of Regional Facility Reliability Projects or Lower Voltage Facility 
Reliability Projects, as applicable.  
(B)
Transmission Provider shall assign cost responsibility for Economic 
Projects that are modifications to Reliability Projects as described in Operating Agreement, 
Schedule 6, section 1.5.7(b)(ii) in accordance with the provisions of this Schedule 12 governing 
the assignment of cost responsibility of Regional Facility Reliability Projects or Lower Voltage 
Facility Reliability Projects, as applicable.
(C)
Transmission Provider shall assign cost responsibility for Economic 
Projects that are new enhancements or expansions that could relieve one or more economic 
Page 97

PDF page 263

constraints as described in Operating Agreement, Schedule 6, section 1.5.7(b)(iii) to the Zones 
that show a decrease in the net present value of the Changes in Load Energy Payment.  The 
Change in Load Energy Payment for each year shall be determined using the methodology set 
forth in Operating Agreement, Schedule 6, section 1.5.7(d) for the period specified in that 
section.  Cost responsibility shall be assigned based on each Zone’s pro rata share of the sum of 
the net present values of the Changes in Load Energy Payment only of the Zones in which the 
net present value of the Changes in Load Energy Payment shows a decrease.
(vi)
Required Transmission Enhancements Costing Less Than $5 Million.  
Notwithstanding sections (b)(i), (b)(ii), (b)(iv) and (b)(v) of this Schedule 12, cost responsibility 
for a Required Transmission Enhancement for which the good faith estimate of the cost of the 
Required Transmission Enhancement (a) prepared in connection with the development of the 
Regional Transmission Expansion Plan and (b) provided to the PJM Board at the time the 
Required Transmission Enhancement is included for the first time in the Regional Transmission 
Expansion Plan, does not equal or exceed $5 million shall be assigned to the Zone where the 
Required Transmission Enhancement is to be located.  The determination of whether the 
estimated cost of a Required Transmission Enhancement does not equal or exceed $5 million 
shall be based solely on such good faith estimate of the cost of the Required Transmission 
Enhancement regardless of the actual costs incurred.  The estimated cost of a Required 
Transmission Enhancement shall include the aggregate estimated costs of all of the transmission 
elements approved by the PJM Board at the time such elements are included in the Regional 
Transmission Expansion Plan that collectively are intended (i) in the case of a Reliability Project, 
to resolve a specific reliability criteria violation, or (ii) in the case of an Economic Project, 
provide a specific LMP Benefit.  Where a Required Transmission Enhancement subject to this 
section (b)(vi) consists of a single transmission element or multiple transmission elements that 
will be located in more than one Zone, each Zone shall be assigned cost responsibility for the 
transmission elements or portions of the transmission elements located in such Zone.  Merchant 
Transmission Facilities shall not be assigned cost responsibility for a Required Transmission 
Enhancement subject to this section (b)(vi).
(vii)
Modifications of Required Transmission Enhancements.  Once a Required 
Transmission Enhancement is included in the Regional Transmission Expansion Plan, any 
modification to such Required Transmission Enhancement that subsequently is included in the 
Regional Transmission Expansion Plan as a separate Reliability or Economic Project shall be 
considered a separate and distinct Required Transmission Enhancement for purposes of cost 
responsibility assignment under this Schedule 12.  Except as provided in sections (b)(iv) and 
(b)(xiv) of this Schedule 12, any cost responsibility assignment that has been made for a 
previously approved Required Transmission Enhancement shall have no impact on the cost 
responsibility assignment of such modification.
(viii)
FERC Filing.  Within 30 days of the approval of each Regional Transmission 
Expansion Plan or an addition to such plan by the PJM Board pursuant to Operating Agreement, 
Schedule 6, section 1.6, the Transmission Provider shall designate in the Tariff, Schedule 12-
Appendix A and in a report filed with the FERC the customers using Point-to-Point 
Transmission Service and/or Network Integration Transmission Service and Merchant 
Transmission Facility owners that will be subject to each such Transmission Enhancement 
Page 98

PDF page 264

Charge (“Responsible Customers”) based on the cost responsibility assignments determined 
pursuant to this Schedule 12.  Those customers designated by the Transmission Provider as 
Responsible Customers shall have 30 days from the date the filing is made with the FERC to 
seek review of such designation. Such cost responsibility designations shall be the same as those 
made for the relevant Regional Facility, Necessary Lower Voltage Facility, or Lower Voltage 
Facility in the Regional Transmission Expansion Plan.
(ix)
Regions With Which PJM Has Entered Into an Agreement Listed in 
Schedule 12-Appendix B .  For purposes of this Schedule 12, where costs of a Required 
Transmission Enhancement are allocated to a region other than PJM pursuant to an agreement set 
forth in Tariff, Schedule 12-Appendix B, Responsible Customers for such costs shall be 
customers in such region. Cost responsibility with respect to the costs of a Required 
Transmission Enhancements  allocated to a region other than PJM shall be allocated within such 
region in accordance with the applicable tariff or agreement governing the allocation of such 
costs in such region.
(x)
Merchant Transmission Facilities.
(A)
For purposes of this Schedule 12, where the Transmission Provider has 
allocated all or a portion of a Required Transmission Enhancement to a Merchant Transmission 
Facility, the owner of the Merchant Transmission Facility shall be the Responsible Customer 
with respect to such Required Transmission Enhancement, and shall pay the Transmission 
Enhancement Charges associated with the Required Transmission Enhancement.
(B)
(1)
Transmission Provider shall defer collection of Transmission 
Enhancement Charges from a Merchant Transmission Facility until the Merchant Transmission 
Facility goes into commercial operation; provided, however, in the event the commercial 
operation of a Merchant Transmission Facility is delayed beyond the commercial operation 
milestone date(s) specified in the Interconnection Service Agreement associated with the 
Merchant Transmission Facility and the Transmission Provider or Transmission Owner 
constructing the Required Transmission Enhancement demonstrates that the Merchant 
Transmission Facility is responsible for such delay, Transmission Provider may begin collecting 
Transmission Enhancement Charges from the Merchant Transmission Facility prior to the 
Merchant Transmission Facility going into commercial operation.  Transmission Enhancement 
Charges allocated to a Merchant Transmission Facility for which collection is deferred in 
accordance with this section (b)(x)(B)(1) shall be recorded in appropriate Transmission Provider 
accounts for deferred charges and collected in accordance with section (b)(x)(B)(3) below.  
(2)
Transmission Provider shall base the collection of Transmission 
Enhancement Charges associated with Required Transmission Enhancements from a Merchant 
Transmission Facility on the actual Firm Transmission Withdrawal Rights that have been 
awarded to the Merchant Transmission Facility; provided, however, to the extent that a Merchant 
Transmission Facility has been awarded less than the amount of Firm Transmission Withdrawal 
Rights specified in the Interconnection Service Agreement associated with the Merchant
Transmission Facility, then Transmission Provider shall record the difference between the 
amount of Transmission Enhancement Charges collected based on the lesser amount of Firm 
Page 99

PDF page 265

Transmission Withdrawal Rights and the amount of Transmission Enhancement Charges based 
on the full amount of Firm Transmission Withdrawal Rights specified in the applicable 
Interconnection Service Agreement in appropriate accounts for deferred charges and, after the 
Merchant Transmission Facility has been awarded the full amount of Firm Transmission 
Withdrawal Rights specified in the Interconnection Service Agreement, collect such deferred 
amounts in accordance with section (b)(x)(B)(3) below.  Notwithstanding the foregoing, 
Transmission Provider may collect Transmission Enhancement Charges based on more than a 
Merchant Transmission Facility’s actually awarded Firm Transmission Withdrawal Rights (not 
to exceed the Firm Transmission Withdrawal Rights specified in the applicable Interconnection 
Service Agreement) if the Transmission Provider or Transmission Owner demonstrates that the 
Merchant Transmission Facility is responsible for receiving fewer Firm Transmission 
Withdrawal Rights than are specified in the applicable Interconnection Service Agreement.
(3)
Transmission Provider shall record: (i) in an appropriate deferred 
asset account, the Transmission Enhancement Charges associated with Required Transmission 
Enhancements for which collection is deferred in accordance with sections (b)(x)(B)(1) and 
(b)(x)(B)(2) above; and (ii) in an appropriate deferred liability account, the revenues associated 
with the Transmission Enhancement Charges that, absent the deferred charges, would have been 
due to Transmission Owners or to Transmission Owners’ customers as directed by the applicable 
Transmission Owner. At such time as collection of such deferred Transmission Enhancement 
Charges are permitted in accordance with sections (b)(x)(B)(1) and (b)(x)(B)(2) above, the 
deferred charges (along with appropriate interest) shall be collected from the Merchant 
Transmission Facility in equal installments over the twelve months following the 
commencement of the collection of the deferred charges. Such amounts shall be distributed to 
Transmission Owners or to Transmission Owners’ customers as directed by the applicable 
Transmission Owner, and the Transmission Provider shall make appropriate adjustments to the 
deferred asset and liability accounts.  Transmission Provider shall not be responsible for 
distributing revenues associated with deferred Transmission Enhancement Charges unless and 
until such charges are collected in accordance with this section (b)(x)(B), and uncollected 
deferred Transmission Enhancement Charges shall not be subject to Default Allocation 
Assessments to the Members pursuant to Operating Agreement, section 15.2.
(xi)
Consolidated Edison Company of New York.
(A) Cost responsibility 
assignments to Consolidated Edison Company of New York for Required Transmission 
Enhancements pursuant to this Schedule 12 with respect to the Firm Point-To-Point Service 
Agreements designated as Original Service Agreement No. 1873 and Original Service 
Agreement No. 1874 accepted by the Commission in Docket No. ER08-858 (“ConEd Service 
Agreements”) shall be in accordance with the terms and conditions of the settlement approved by 
the FERC in Docket No. ER08-858-000.  (B) All cost responsibility assignments for Required 
Transmission Enhancements pursuant to this Schedule 12 shall be adjusted at the commencement 
and termination of service under the ConEd Service Agreements to take account of the 
assignments under subsection (xi)(A) of this section.  
(xii)
Public Policy Projects.  
Page 100

PDF page 266

(A)
Transmission Facilities as defined in  Consolidated Transmission Owners 
Agreement, section 1.27 constructed by a Transmission Owner pursuant to a Public Policy 
Requirement but not included in a Regional Transmission Expansion Plan as a Required 
Transmission Enhancement, shall be as considered a Supplemental Project. 
(B)
If a transmission enhancement or expansion is proposed pursuant to 
Operating Agreement, Schedule 6, section 1.5.9(a) which is not a Supplemental Project (“State 
Agreement Public Policy Project”),  the Transmission Provider shall submit the assignment of 
costs to Responsible Customers proposed in connection with such State Agreement Public Policy 
Project to the Transmission Owners Agreement Administrative Committee for consideration and 
filing pursuant to Consolidated Transmission Owners Agreement, section 7.3 and Tariff, Part I, 
section 9.1(a).  Nothing in this section (b)(xii) shall prevent the Transmission Provider or the 
state governmental entities proposing such State Agreement Public Policy Project from filing a 
proposed assignment of costs to Responsible Customers for such project pursuant to Section 206 
of the Federal Power Act.
(xiii)
Replacement of Transmission Facilities.  Unless determined by PJM to be a 
Required Transmission Enhancement included in a Regional Transmission Expansion Plan, cost 
responsibility for the replacement of Transmission Facilities, as defined in Consolidated 
Transmission Owners Agreement, section 1.27, shall be assigned to the Zonal loads and Merchant 
Transmission Facilities responsible for the costs of the Transmission Facilities being replaced.
(xiv)    Multi-Driver Projects.  
(A)
Assignment of Proportional Multi-Driver Project Costs.  The Transmission 
Provider shall assign cost responsibility for Proportional Multi-Driver Projects in proportion 
to the relative percentage benefit that each driver of a Proportional Multi-Driver Project 
addresses, respectively, reliability violations or operational performance (“reliability”), 
economic constraints (“economic”) and/or Public Policy Requirements (“public policy”) as 
follows: 
(1)
As part of the open planning process provided for in Operating 
Agreement, Schedule 6, section 1.5.10(h), the Transmission Provider employs the 
Proportional Method to develop a Proportional Multi-Driver Project, by determining 
which of the following drivers a Proportional Multi-Driver Project addresses: 
reliability, economic, or public policy, and the extent to which each such driver 
contributes to the size, scope, and estimated costs of such Proportional Multi-Driver 
Project (irrespective of the reliability cost allocation treatment that is otherwise 
accorded an incremental market efficiency modification thereto pursuant to section 
(b)(v)(B) of this Schedule 12).  The Transmission Provider shall identify the 
contribution of each driver in terms of a percentage totaling 100 percent for all such 
drivers at the time that each Proportional Multi-Driver Project is submitted to the PJM 
Board for approval and included in the Regional Transmission Expansion Plan. The 
percentage contribution of each driver shall be based on the ratio of the estimated cost 
of each project that the Multi-Driver Project replaces to the total of the estimated costs 
Page 101

PDF page 267

of all projects combined into the Multi-Driver Project. 
(2)
Once a Proportional Multi-Driver Project is approved by the PJM Board, 
the percentage contributions of each driver shall not be changed unless the PJM Board 
subsequently approves an upgrade or modification to the Proportional Multi-Driver 
Project.  In that event, the cost responsibility for the Proportional Multi-Driver Project, 
including any costs incurred prior to the upgrade or modification, will be determined as 
if it were a new Proportional Multi-Driver Project, such that the percentage 
contribution for each driver shall be established anew.  
(B)
Assignment of Incremental Multi-Driver Project Costs.  The Transmission 
Provider shall assign cost responsibility for  Incremental Multi-Driver Projects as defined in 
Operating Agreement, Schedule 6, section 1.15B using the same methodology described in 
section (b)(xiv)(A)(1) above treating the estimated cost of modifying the original project as if 
it were the estimated cost of a separate project included in a Proportional Multi-Driver 
Project.  Any costs that had been expended on the original project prior its designation by 
Transmission Provider as an Incremental Multi-Driver Project shall be included in the 
calculation of the Incremental Multi-Driver Project pursuant to this section (b)(xiv)(B).  
(C)
The Transmission Provider shall separately assign cost responsibility for the 
costs assigned to each driver pursuant to this section (b)(xiv) in accordance with the provisions 
of this Schedule 12 governing the assignment of cost responsibility for a single driver project 
of each driver’s respective type (reliability, economic or public policy).  Except as provided in 
section (b)(xiv)(D) below, cost responsibility will be assigned based on the final voltage and 
configuration of the Multi-Driver Project determined in accordance with sections (b)(i), (b)(ii), 
or (b)(vi) of this Schedule 12. 
(D)     Notwithstanding the cost assignments that would otherwise be provided for in 
section (b)(xiv)(C) above, if a Multi-Driver Project includes a public policy driver that is the 
result of the State Agreement Approach provided for in Operating Agreement, Schedule 6, 
section 1.5.9 and is a Regional Facility as defined in section (b)(i) of this Schedule 12 and such 
Multi-Driver Project would not be a Regional Facility but for the inclusion of the public policy 
driver, then the percentage of costs of such Multi-Driver Project assigned to the non-public 
policy drivers in accordance with the procedures set forth in in section (b)(i)(A)(1) above shall 
be twenty percent (20%) and the percentage of costs assigned to the non-public policy drivers 
of such Multi-Driver Project in accordance section (b)(i)(A)(2) above shall be eighty percent 
(80%), and not the fifty percent (50%) cost responsibility percentages provided for in section 
(b)(i)(A)(i) and section (b)(i)(A)(2), respectively, of this Schedule 12. 
(xv) Reserved.
(xvi)
Required Transmission Enhancements Designed to Address Reliability 
Violations on Transmission Facilities Operating Below 200 kV. Notwithstanding section 
(b)(ii), above, cost responsibility for any Required Transmission Enhancements that are included 
in the Regional Transmission Expansion Plan to address reliability violations on Transmission 
Facilities that are designed to operate at below 200 kV and, pursuant to Operating Agreement, 
Page 102

PDF page 268

Schedule 6, section 1.5.8(n), were not included in an Operating Agreement, Schedule 6, section 
1.5.8(c) proposal window, shall be assigned to the Responsible Customers in the Zone where the 
Required Transmission Enhancement is to be located.
(xvii) Required Transmission Enhancements Constructed As Targeted Market 
Efficiency Projects Under The Midcontinent Independent Transmission System Operator, 
Inc. and PJM Interconnection, L.L.C. Coordinated System Plan.   Notwithstanding sections 
(b)(i), (b)(ii), (b)(iv), (b)(v), (b)(vi) and (b)(x)(B)(2) of this Schedule 12, cost responsibility for 
the costs of a Required Transmission Enhancement that is included in the Regional Transmission 
Expansion Plan because it is a Targeted Market Efficiency Project (“TMEP”) identified in the 
Coordinated System Plan periodically developed pursuant to the Joint Operating Agreement 
Between the Midcontinent Independent Transmission System Operator, Inc. and PJM 
Interconnection, L.L.C. (“PJM-MISO JOA”) and assigned to PJM pursuant to PJM-MISO JOA, 
section 9.4.4.2.5, shall be assigned among Zones and Merchant Transmission Facilities in 
accordance with this section (b)(xvii).  Using the Targeted Market Efficiency Project study 
conducted pursuant to PJM-MISO JOA, section 9.3.7.2(c) of in which the TMEP was identified, 
the Transmission Provider shall determine, in accordance with Tariff, Attachment K-Appendix, 
section 5.1, the average annual Transmission Congestion Charges experienced by Market Buyers 
in Zones and at Merchant Transmission Facilities attributable to the targeted Reciprocal 
Coordinated Flowgate during the two historical calendar years prior to the study year of the 
Targeted Market Efficiency Project study.  In making this determination, the Transmission 
Provider shall net any increases in Day-ahead and Real-time Prices paid by Market Buyers in a 
Zone or at a Merchant Transmission Facility against any decreases in Day-ahead and Real-time 
Prices paid by Market Buyers in such Zone or at such Merchant Transmission Facility 
attributable to the targeted Reciprocal Coordinated Flowgate.  Where a single TMEP is 
constructed to reduce Transmission Congestion Charges attributable to more than one targeted 
Reciprocal Coordinated Flowgate, the Transmission Provider shall net any increases in Day-
ahead and Real-time Prices paid by Market Buyers in a Zone or at a Merchant Transmission 
Facility against any decreases in Day-ahead and Real-time Prices paid by Market Buyers in such 
Zone or at such Merchant Transmission Facility attributable to all targeted Reciprocal 
Coordinated Flowgates.  Cost responsibility shall be assigned based on each Zone’s and 
Merchant Transmission Facility’s pro rata share of the sum of the net Transmission Congestion 
Charges paid by Market Buyers only of the Zones and Merchant Transmission Facilities in 
which Market Buyers experienced net Transmission Congestion Charges.
(xviii) Required Transmission Enhancements Designed to Address Stability Issues.
For purposes of the assignment of cost responsibility for Reliability Projects designed to address 
stability issues under subsection (b)(i)(A)(2)(a) and subsection (b)(ii)(A) of this Schedule 12, the 
Transmission Provider shall, using the same inputs and assumptions from the simulation that 
originally drove the need for the stability upgrade, perform a stability simulation that includes 
the stability upgrade under the worst fault condition. The worst fault condition shall be the fault 
condition in the simulation that produces the maximum rotor angle swing with the stability 
upgrade included.  For each load bus on the system, the difference between the highest and 
lowest voltage angle that occurs during the simulation of the worst fault condition will be 
recorded. Load buses having a voltage angle deviation less than 25 percent of the load bus with 
the largest voltage angle deviation will not be included in the cost allocation calculation. For the 
Page 103

PDF page 269

remaining load buses, the voltage angle deviation will be multiplied by the megawatt load at the 
bus obtained from the stability simulation model, or, in the case of a Merchant Transmission 
Facility, the Firm Transmission Withdrawal Rights at the bus. The products of the voltage angle 
deviation and megawatt load at each bus will be summed for each Responsible Zone. The 
Stability Deviation cost allocation for a Responsible Zone or Merchant Transmission Facility 
will be determined by dividing the sum of the load-weighted angle deviations for the 
Responsible Zone or Merchant Transmission Facility by the sum of the load-weighted angle 
deviations for each Responsible Zone and Merchant Transmission Facility. Transmission 
Provider shall round cost responsibility assignments to the nearest one-hundredth of one percent.
(c)
Determination of Transmission Enhancement Charges. In the event that any 
Transmission Owner recovers the cost of a Required Transmission Enhancement through a 
Transmission Enhancement Charge, such charge shall be determined as follows:
(1)
Transmission Provider shall identify in writing and post on the PJM Internet site 
the Required Transmission Enhancement(s) to which each Transmission Enhancement 
Charge corresponds. The Transmission Enhancement Charge with respect to a Required 
Transmission Enhancement shall recover the applicable Transmission Owner’s annual 
transmission revenue requirement associated with the Required Transmission 
Enhancement.
(2)  
Each Transmission Enhancement Charge shall be a monthly charge based on all 
costs and applicable incentives associated with a particular Required Transmission 
Enhancement for which the Transmission Owner is responsible. 
(3) 
A Transmission Owner’s annual transmission revenue requirement associated 
with a Required Transmission Enhancement shall be determined pursuant to either (i) a 
unilateral filing by the Transmission Owner under Section 205 of the Federal Power Act 
and the FERC’s rules and regulations thereunder; or (ii) a formula rate in effect 
applicable to the Transmission Owner’s rates for Network Integration Transmission 
Service, including the costs associated with Required Transmission Enhancements. 
(4) 
Each Transmission Enhancement Charge applicable to Network Customers and 
Non-Zone Network Customers shall be recalculated annually to reflect the annual 
revisions to the billing determinants used by the Transmission Provider to calculate 
charges to Network Customers for Network Integration Transmission Service under 
Tariff, Part III, section 34.1.  The Transmission Provider shall post on its Internet site by 
October 31 of each calendar year each recalculated Transmission Enhancement Charge 
that shall be effective during the subsequent calendar year.
(5) 
Each Transmission Enhancement Charge applicable to customers using Point-To-
Point Transmission Service shall be calculated monthly to reflect the billing determinants 
used by the Transmission Provider to determine charges for customers of Point-To-Point 
Transmission Service in accordance with Tariff, Part II, section 25. 
Page 104

PDF page 270

(6)
Each Transmission Enhancement Charge payable by an owner of a Merchant 
Transmission Facility pursuant to section (b) of this Schedule 12 shall be calculated as a 
fixed monthly charge. 
(7)
If a Transmission Owner chooses to recover the cost of Required Transmission 
Enhancements through the operation of a formula rate as described in section (a) of this 
Schedule 12, the Transmission Owner must make an informational filing with the 
Commission one year from the date the selecting Transmission Owner’s formula rates go 
into effect, and each year thereafter, providing a detailed list of the costs the 
Transmission Owner has incurred, and the revenues the Transmission Owner has 
received to provide service.
(d)
Recovery of Transmission Enhancement Charges.  
(1)
Responsible Customers shall pay Transmission Provider all applicable 
Transmission Enhancement Charges as required by this Schedule 12 in addition to 
all other charges for transmission service for which such Responsible Customers 
are responsible under the Tariff.
(2)
Transmission Provider shall collect all applicable Transmission Enhancement 
Charges from each Responsible Customer on a monthly basis.  Transmission 
Provider shall remit or credit all revenues received from Responsible Customers 
under this Schedule 12 to the Transmission Owner(s) that established such charge 
or to the appropriate authority in a region other than PJM in the case of 
Transmission Enhancement Charges established in such region in connection with 
a Required Transmission Enhancement constructed pursuant to an Appendix B 
Agreement, to be distributed in accordance with the applicable tariff or agreement 
governing the distribution of such charges in such region.
(e)
Crediting of Revenue from Transmission Enhancement Charges.  In recognition that 
a Transmission Owner’s charges for Network Integration Transmission Service set forth in 
Tariff, Attachment H are established based upon the Transmission Owner’s total cost of 
providing FERC-jurisdictional transmission service, including the costs associated with Required 
Transmission Enhancements, revenue from a Transmission Owner’s Transmission Enhancement 
Charges for a billing month shall be credited pursuant to this Schedule 12 to the Network 
Customers in the Transmission Owner’s Zone (including, where applicable, the Transmission 
Owner) and Transmission Customers purchasing Firm Point-to-Point Transmission Service for 
delivery in the Transmission Owner’s Zone in proportion to their Demand Charges (including 
any imputed Demand Charges for bundled service to Native Load Customers) for Network 
Integration Transmission Service and Reserved Capacity for Firm Point-to-Point Transmission 
Service; provided that such credits shall be reduced by the amount of any applicable incentives 
included in such Transmission Enhancement Charges.  
(f)
Recovery of Interconnection Reliability Reinforcement Costs.  
Page 105

PDF page 271

(1)
Customers Subject to Cost Responsibility for Interconnection Reliability 
Reinforcements. For each Fast Energization Process Cycle, the Transmission 
Provider shall determine cost responsibility for Interconnection Reliability 
Reinforcements identified and designated for construction pursuant to this section 
(f) of this Schedule 12.  Cost responsibility for Interconnection Reliability 
Reinforcements in a Fast Energization Cycle shall be assigned to Responsible 
Customers in Zones containing Transmission Customers taking Firm 
Transmission Service on behalf of Eligible Loads and Large Loads (“Large Load 
Zones”).  Generator Interconnection Customers in a given Cycle that are parties to 
a Generator Interconnection Agreement will pay a Generator Reliability 
Reinforcement Fee established in section (f)(vi) below.    
(2)
Determination of Cost Responsibility and Generator Allocation for 
Interconnection Reliability Reinforcements.  The Transmission Provider shall 
determine cost responsibility for Interconnection Reliability Reinforcements and 
the Generator Reliability Reinforcement Fee based on a proportional impact 
approach that considers all of the constraints identified in the Fast Energization 
Process Cycle.  
This proportional impact methodology will apply to thermal and non-thermal 
constraints, and will determine the pro rata share of impacts of Project 
Developers, Eligible Loads and Large Loads on the aggregate of constraints being 
alleviated by the portfolio of Interconnection Reliability Reinforcements as 
further described below and in the PJM Manuals.
The Transmission Provider shall determine each Project Developer, Eligible Load 
and Large Load’s proportional impact as follows:
(A)
With respect to the portfolio of Interconnection Reliability Reinforcements 
addressing thermal, stability and voltage constraints:
(1)
The Transmission Provider shall apply aggregation and thresholds 
as set forth in the PJM Manuals to identify the set of constrained 
facilities identified as having violations requiring mitigation 
through Interconnection Reliability Reinforcements in the Fast 
Energization Process Cycle studies, resulting in distribution 
factors, represented as decimal values or percentages, which 
express the portions of impact on constrained facilities from each 
Project Developer, Eligible Customer seeking Long-Term Firm 
Point-to-Point Transmission Service, Eligible Load, or Large Load.  
(2)
For purposes of determining MW impacts, each calculated 
distribution factor, if it exceeds the threshold set forth in the PJM 
Manuals, shall first be multiplied, for each Project Developer, 
Eligible Customer seeking Long-Term Firm Point-to-Point 
Page 106

PDF page 272

Transmission Service, Eligible Load or Large Load, by its 
requested MW value as studied in the Fast Energization Process.  
(3)
No allocation relating to a constrained facility shall result unless 
the calculated MW impact exceeds the thresholds set forth in the 
PJM Manuals.
(4)
All calculated MW impacts on constrained facilities above the 
relevant thresholds for each Project Developer, Eligible Customer 
seeking Long-Term Firm Point-to-Point Transmission Service, 
Eligible Load or Large Load are converted to proportional MW 
impacts representing the pro rata share of all MW impacts on the 
same constrained facility.
(5)
The proportional MW impacts are weighted using values as further 
described in the PJM Manuals resulting in a weighted proportional 
MW impact.
(6)
The percentage proportional impact values allocated for each Project 
Developer, Eligible Load or Large Load is based on its pro rata share 
of the weighted proportional MW impact relative to the total of 
weighted proportional MW impact for the Cycle.  For Project 
Developers, this value is the Generation Interconnection Customer’s 
Allocated Percentage (GCAP) as outlined in (f)(vi)(B).
(B)
With respect to the portfolio of Interconnection Reliability Reinforcements 
addressing short-circuit constraints, allocation will be based on contributing fault 
current impact on the circuit breaker’s applicable interrupting rating, as set forth 
in the PJM Manuals.
(C)
The aggregate impact values calculated pursuant to subsection (f)(ii)(A) 
and (f)(ii)(B) above shall determine the relative assignment of cost responsibility 
for Interconnection Reliability Reinforcements and the Generator Reliability 
Reinforcement Fee subject to the following rules:
 
(1)
The percentage proportional impacts of Eligible Load and Large 
Load Transmission Service Requests will be summed on a Zonal 
basis assigned to the relevant Transmission Owner Zones.
(2)
For purposes of this proportional allocation, the entire cost 
responsibility calculated pursuant to this subsection (f)(ii) will be 
assigned to Transmission Owner Zones based on their summed 
percentage proportional impacts.  Interconnection Reliability 
Reinforcement costs representing the relative contribution 
attributable to Generator Interconnection Customers shall be 
recovered from Generator Interconnection Customers through 
Page 107

PDF page 273

Generator Reliability Reinforcement Fees as set forth in subsection 
(f)(vi) below.
(D)
The Transmission Provider shall complete the analysis described in this 
subsection (f)(ii) within 30 days before Transmission Service Agreements and 
Generator Interconnection Agreements have been executed.  Within 30 days of 
the completion of this analysis, the Transmission Provider shall post on the PJM 
Internet Site the cost responsibility assignments determined pursuant to this 
section (f).  
(3)
Interconnection Reliability Reinforcements Charge.  The charge established to 
recover the revenue requirement with respect to an Interconnection Reliability 
Reinforcement is hereafter referred to as an “Interconnection Reliability 
Reinforcement Charge.”  Interconnection Reliability Reinforcement Charges of 
one or more Transmission Owners for Interconnection Reliability Reinforcements 
shall be established in accordance with this section (f) of Schedule 12.  
Transmission Provider shall assess an Interconnection Reliability Reinforcement 
Charge to Firm Transmission Customers in Zones based on the cost responsibility 
assignments determined pursuant to subsection (f)(ii) above.  The Interconnection 
Reliability Reinforcement Charge shall recover the applicable Transmission 
Owner's annual transmission revenue requirement associated with the 
Interconnection Reliability Reinforcements constructed and owned and/or 
financed by that Transmission Owner for a period of 15 years after an 
Interconnection Reliability Reinforcement enters service.  After this period, 
beginning with the next full calendar year, Transmission Provider will assign 
responsibility for and recover the remaining costs of the Interconnection 
Reliability Reinforcement in accordance with sections (a) through (e) of this 
Schedule 12. 
(A)
A Transmission Owner’s annual transmission revenue requirement 
associated with an Interconnection Reliability Reinforcement shall be determined 
pursuant to the formula rate in effect applicable to the Transmission Owner’s rates 
for Network Integration Transmission Service and Firm Contract Demand 
Transmission Service (“Firm Transmission Service”), including the costs 
associated with Interconnection Reliability Reinforcements.
(B)
Each Interconnection Reliability Reinforcement Charge applicable to Firm 
Transmission Customers shall be recalculated annually to reflect the annual 
revisions to the billing determinants used by the Transmission Provider to 
calculate charges for Firm Transmission Service.  The Transmission Provider 
shall post on its Internet site by October 31 of each calendar year each 
recalculated Interconnection Reliability Reinforcement Charge that shall be 
effective during the subsequent calendar year.
(C)
Each Interconnection Reliability Reinforcement Charge applicable to 
customers using Point-To-Point Transmission Service shall be calculated monthly 
Page 108

PDF page 274

to reflect the billing determinants used by the Transmission Provider to determine 
charges for customers of Point-To-Point Transmission Service in accordance with 
Tariff, Part II, section 25.
(4)
Recovery of Interconnection Reliability Reinforcement Charges.
(A)
Transmission Customers shall pay the Transmission Provider all 
applicable Interconnection Reliability Reinforcement Charge as required by this 
Schedule 12 in addition to all other charges for transmission service for which 
such Transmission Customers are responsible under the Tariff.
(B)
The Transmission Provider shall collect all applicable Interconnection 
Reliability Reinforcement Charges from each applicable Transmission Customer 
on a monthly basis. The Transmission Provider shall remit or credit all revenues 
received from Transmission Customers under this Schedule 12 to the 
Transmission Owner(s) owning the relevant Interconnection Reliability 
Reinforcements.
(5)
Crediting of Revenue from Interconnection Reliability Reinforcement 
Charges.  In recognition that a Transmission Owner’s charges for Firm 
Transmission Service set forth in Tariff, Attachment H are established based upon 
the Transmission Owner's total cost of providing FERC-jurisdictional 
transmission service, including the costs associated with Interconnection 
Reliability Reinforcements, revenue Interconnection Reliability Reinforcement 
Charges for a billing month shall be credited pursuant to this Schedule 12 to the 
Firm Transmission Customers in the Transmission Owner’s Zone (including, 
where applicable, the Transmission Owner) and Transmission Customers 
purchasing Firm Point-To-Point Transmission Service for delivery in the 
Transmission Owner's Zone in proportion to their Demand Charges (including 
any imputed Demand Charges for bundled service to Native Load Customers) for 
Network Integration Transmission Service and Reserved Capacity for Firm 
Contract Demand Transmission Service and Firm Point-To-Point Transmission 
Service; provided that such credits shall be reduced by the amount of any 
applicable incentives included in such Interconnection Reliability Reinforcement 
Charges.
(6)
Generator Reliability Reinforcement Fee.  The Transmission Provider shall 
recover the portion of the costs of Interconnection Reliability Reinforcements 
allocated to Generator Interconnection Customers in a Fast Energization Process 
Cycle, as determined pursuant to subsection (f)(ii) of this Schedule 12, through 
Generator Interconnection Reliability Reinforcement Fees as follows:
(A)
The Transmission Provider shall assess and each Generator 
Interconnection Customer will pay the Generator Reliability Reinforcement Fee 
beginning on the earlier of: (1) in the calendar year when the Generator 
Interconnection Customer’s facility achieves Commercial Operation, or (2) three 
Page 109

PDF page 275

years after the Commercial Operation date in the Customer’s original Generator 
Interconnection Agreement, and continuing for a period of 15 years from the 
Commercial Operation Date.
(B)
The Transmission Provider shall calculate the Generator Reliability 
Reinforcement Fee after each System Impact Study Phase as part of the Fast 
Energization Process as follows:
AGRRRF = GCAP X TRRGP x {[ACCC X (1 + ACCC)15]/[(1 + ACCC)15 – 1]}
Where:
GRRRF is the Generator Reliability Reinforcement Fee
GCAP is the Generator Interconnection Customer’s Allocated Percentage, which 
is the Generator Interconnection Customer’s allocated percentage for the portfolio 
of Interconnection Reliability Reinforcements from its New Service Request 
Cycle, determined pursuant to subsection (f)(ii) above.
 
TRRGP is the Total Reliability Reinforcement Gross Plant, which is based on the 
gross plant of all Interconnection Reliability Reinforcements included in the 
RTEP approved by the PJM Board with respect to the Generator Interconnection 
Customer’s New Service Request Cycle, and for which it has been allocated a 
percentage pursuant to subsection (f)(ii) above.  The gross plant amounts used in 
this calculation shall be based on the final estimated costs of the Interconnection 
Reliability Reinforcements as determined by the Transmission Provider through 
the Fast Energization Process.  
ACCC is the Annual Carrying Charge Component, which shall be calculated as 
the weighted average of the Weighted Average Cost of Capital for all 
Transmission Owners with Interconnection Reliability Reinforcements included 
in the RTEP approved by the PJM Board with respect to the Generator 
Interconnection Customer’s New Service Request Cycle.  The Weighted Average 
Cost of Capital values shall be derived from the applicable Transmission Owner’s 
formula rates, as set forth in Attachment H and in effect at the time the Annual 
Generator Reliability Reinforcement Fee is calculated.  For purposes of 
calculating such weighted average, each applicable Transmission Owner’s 
Weighted Average Cost of Capital shall be weighted based on the ratio of the 
final estimated costs of the Interconnection Reliability Reinforcements that it has 
been designated to construct and own and/or finance identified in the New Service 
Request Cycle that contains the Generator Interconnection Customer, to the final 
estimated costs for all Interconnection Reliability Reinforcements identified in the 
New Service Request Cycle that contains the Generator Interconnection 
Customer.  
Page 110

PDF page 276

SCHEDULE 20
Firm Contract Demand Transmission Service
For Eligible Load and Large Load
1)
Eligible Customer taking Firm Contract Demand Transmission Service in a Zone in 
which Network Integration Transmission Service rates are determined based on formula rates set 
forth in Attachment H shall pay a Monthly Demand Charge based on the Firm Contract Demand 
Transmission Service Amount (MW), as specified in Eligible Customer’s Service Agreement, 
which shall be determined as follows:
MDC = FCDTSA X RTZ/12
Where:
MDC is the monthly demand charge
FCDTSA is the Firm Contract Demand Transmission Service Amount (MW), as 
specified in Eligible Customer’s Service Agreement 
RTZ is the rate for Network Integration Transmission Service from Attachment H for the 
Zone in which the Eligible Customer’s Eligible Load or Large Load is located, stated in 
dollars per megawatt per year.  For purposes of establishing the RTZ component in the 
relevant Attachment H, the annual peak of the Zone shall be based on the sum of 
Network Customer Loads in the Zone and Firm Contract Demand Transmission Service 
Amounts for all Eligible Customers taking Firm Contract Demand Transmission Service 
in the Zone for the applicable peak period.
2)
Eligible Customers taking Firm Contract Demand Transmission Service in a Zone in 
which Network Integration Transmission Service rates are not established based on formula rates 
shall pay a Monthly Demand Charge based on the Firm Contract Demand Transmission Service 
Amount (MW), as specified in Eligible Customer’s Service Agreement, multiplied by a Zonal-
specific Firm Contract Demand Transmission Service rate filed with FERC pursuant to Section 
205 of the Federal Power Act.  Those rates will be posted on Transmission Provider’s website.
3)
Revenue Crediting.  Each month, credits will be applied to the Eligible Customer’s 
gross Monthly Demand Charge stated above associated with revenue collected from Non-Firm 
Contract Demand Transmission Service Charges in accordance with Schedule 19, based on each  
Eligible Customer’s pro rata share of the Zone’s annual peak load, from the most recent 12-
month period ending October 31.  The Eligible Customer’s pro rata share shall be based on the 
ratio of its Firm Contract Demand Transmission Service Amount during the peak period to the 
sum of Network Customer Loads in the Zone and Firm Contract Demand Transmission Service 
Amounts for all Eligible Customers taking Firm Contract Demand Transmission Service in the 
Zone for the applicable peak period.  The sum of these revenue credits will appear as a reduction 
to the gross monthly rate stated above on a Eligible Customer’s bill in that month for service 
under this schedule.  
Page 111

PDF page 277

4)
Transmission Enhancement Charges. In addition to the rates set forth in section (1) of 
this Schedule and any other applicable charges, the Eligible Customer shall also pay any 
Transmission Enhancement Charges for which it is designated as a Responsible Customer 
under Schedule 12 appended to the Tariff.
5)
Determination of Monthly Charges for ComEd Zone. On a monthly basis, revenue
credits shall be calculated based on the sum of ComEd’s share of revenues collected during the 
month from: (i) the PJM Border Rate under Schedule 7; (ii) Network Integration Transmission 
Service to Non-Zone Network Load under Attachment H-A; and (iii) any Point-To-Point 
Transmission Service where the Point of Receipt and the Point of Delivery are both internal to 
the ComEd Zone.  On this basis, the sum of these revenues will appear as a reduction to the gross 
monthly rate stated above on a Transmission Customer’s1 bill in that month for service under this 
schedule.
6)
Determination of Monthly Charges for AEP Zone. On a monthly basis, revenue 
credits shall be calculated based on the sum of AEP’s share of revenues collected during the 
month from: (i) the PJM Border Rate under Schedule 7; (ii) Network Integration Transmission 
Service to Non-Zone Network Load under Attachment H-A; and (iii) Firm Point-To-Point 
Transmission Service where the Point of Delivery is internal to the AEP Zone.  The sum of these 
revenue credits will appear as an adjustment (reduction) to the gross monthly rate stated above 
on a Eligible Customer’s bill in that month for service under this schedule.
7)
Other Supporting Facilities and Taxes.  In addition to the charges set forth in section 
(1) of this schedule, the Eligible Customer shall pay charges determined on a case-by-case basis 
for facilities necessary to provide Transmission Service at voltages lower than those shown 
in Attachment H for the applicable Zone(s) and any amounts necessary to reimburse 
the Transmission Provider for any amounts payable as sales, excise, “Btu,” carbon, value-added 
or similar taxes (other than taxes based upon or measured by net income) with respect to the 
amounts payable pursuant to the Tariff. 
1/ Transmission Customer is defined as an Eligible Customer that executes a Service Agreement, 
or requests PJM file an unexecuted Service Agreement, to receive transmission service under the 
Tariff.
Page 112

PDF page 278

SCHEDULE 21
Non-Firm Contract Demand Service
For Eligible Load and Large Load
1)
Eligible Customer taking Non-Firm Contract Demand Transmission Service in a Zone in 
which Network Integration Transmission Service rates are determined based on formula rates set 
forth in Attachment H shall pay for such service at a discounted reservation rate calculated by 
applying the Zone’s Annual Load Factor to the applicable Zonal Firm Contract Demand 
Transmission Service rate as follows:
Monthly Rate ($/MW): Zonal Firm Contract Demand Transmission Rate (RTZ) multiplied by 
the Zone’s Annual Load Factor, and divided by 12, where the Annual Load Factor is calculated 
as follows: Annual Load Factor = Zonal Annual Energy divided by (Zonal Peak Demand 
multiplied by 8,760 hours).  For purposes of this Schedule, Zonal Annual Energy shall be the 
total net energy for load measured as net generation plus energy receipts minus energy deliveries 
for the Zone from the 12-month period ending October 31 preceding the calendar year during 
which Non-Firm Contract Demand Transmission Service is taken.  For purposes of this 
Schedule, Zonal Peak Demand shall be the Zone’s annual peak load from the 12-month period 
ending October 31 preceding the calendar year during which Non-Firm Contract Demand 
Transmission Service is taken.
Weekly Rate ($/MW): Zonal Firm Contract Demand Transmission Rate (RTZ) multiplied by the 
Zone’s Annual Load Factor, and divided by 52, where the Annual Load Factor is calculated as 
follows: Annual Load Factor = Zonal Annual Energy divided by (Zonal Peak Demand multiplied 
by 8,760 hours).
Daily On-Peak Rate1 ($/MW): Weekly Rate divided by 5.
Daily Off-Peak Rate2 ($/MW): Weekly Rate divided by 7.
Hourly On-Peak Rate3 ($/MWh): Zonal Firm Contract Demand Transmission Rate (RTZ), 
multiplied by the Zone’s Annual Load Factor, and divided by 4,160.
Hourly Off-Peak Rate4 ($/MWh): Zonal Firm Contract Demand Transmission Rate (RTZ), 
multiplied by the Zone’s Annual Load Factor, divided by 8,760.
1/ Monday–Friday except the following holidays: New Years Day, Memorial Day, Independence 
Day, Labor Day, Thanksgiving Day, and Christmas Day.
2/ Saturday and Sunday and the following holidays: New Years Day, Memorial Day, 
Independence Day, Labor Day, Thanksgiving Day, and Christmas Day.
3/ 7:00 a.m. up to the hour ending 11:00 p.m.
4/ 11:00 p.m. up to the hour ending 7:00 a.m.
Page 113

PDF page 279

2)
Eligible Customers taking Non-Firm Contract Demand Transmission Service in a Zone in 
which Network Integration Transmission Service rates are not established based on formula rates 
shall pay for Non-Firm Contract Demand Transmission Service based on the amount of Non-
Firm Contract Demand Transmission Service reserved by the Eligible Customer in MW, 
multiplied by Zonal-specific Non-Firm Contract Demand Transmission Service rates filed with 
FERC pursuant to Section 205 of the Federal Power Act.  Those rates will be posted on 
Transmission Provider’s website.
3)
Discounts.  Three principal requirements apply to discounts for Non-Firm Contract 
Demand Transmission Service as follows: (1) any offer of a discount made by the Transmission 
Provider must be announced to all Eligible Customers solely by posting on the OASIS, (2) any 
customer-initiated requests for discounts (including requests for use by one’s wholesale 
merchant or an Affiliate’s use) must occur solely by posting on OASIS, and (3) once a discount 
is negotiated, details must be immediately posted on the OASIS.  For any discount agreed to by  
Transmission Provider, Transmission Provider must offer the same discounted transmission 
service rate for the same time period to all Eligible Customers taking Non-Firm Contract 
Demand Transmission Service.
4)
Revenue Crediting.  Revenues collected from Non-Firm Contract Demand Transmission 
Service Charges shall be credited to Eligible Customers taking Network Integration Transmission 
Service, Firm Contract Demand Transmission Service, and Firm Point-to-Point Transmission 
Service based on each Eligible Customer’s pro rata share of the Zone’s annual peak load based 
on the most recent 12-month period ending October 31.  The Eligible Customer’s pro rata share 
shall be based on the ratio of its Zone Network Load, Firm Point-To-Point Transmission Service 
and Firm Contract Demand Transmission Service Amount to the sum of Network Customer 
Loads in the Zone and Firm Contract Demand Transmission Service Amounts for all Eligible 
Customers taking Firm Contract Demand Transmission Service in the Zone, for the applicable 
peak period.  The sum of these revenue credits will appear as a reduction to the gross monthly 
rate for Firm Contract Demand Transmission Service on a Eligible Customer’s bill in that month. 
5)
Other Supporting Facilities and Taxes.  In addition to the charges set forth in section 
(1) of this schedule, the Eligible Customer shall pay charges determined on a case-by-case basis 
for facilities necessary to provide Transmission Service at voltages lower than those shown 
in Attachment H for the applicable Zone(s) and any amounts necessary to reimburse 
the Transmission Provider for any amounts payable as sales, excise, “Btu,” carbon, value-added 
or similar taxes (other than taxes based upon or measured by net income) with respect to the 
amounts payable pursuant to the Tariff.
Page 114

PDF page 280

SCHEDULE 22
Financial Penalty Charge for 
Unreserved Use by Eligible Load and Large Load
An Eligible Customer taking Firm Contract Demand Transmission Service, Non-Firm Contract 
Demand Transmission Service, or Interim Network Integration Transmission Service on behalf 
of Eligible Load or Large Load shall be subject to financial penalties for its unreserved use of the 
transmission system.
The financial penalty charge for unreserved use shall include two components: (1) a base penalty 
charge, which applies to each individual hour in which the reserved transmission service limit is 
exceeded, and (2) a penalty ratchet, which applies when such exceedances occur repeatedly.
Base Penalty Charge
When an Eligible Customer taking service on behalf of Eligible Load or Large Load exceeds its 
reserved transmission service limit, a base penalty charge shall be assessed for any hour in which 
at least one five-minute interval occurs during which the Eligible Customer’s telemetered load at 
the Point of Delivery exceeds its reserved transmission service limit.  This five-minute interval is 
defined as an Exceedance Interval, and such an hour is defined as an Exceedance Hour.  The 
base penalty charge shall apply to each Exceedance Hour.  
For an Eligible Customer taking only Firm Contract Demand Transmission Service, the 
reserved transmission service limit shall equal the Firm Contract Demand Transmission 
Service minus any curtailed MW.  
For an Eligible Customer taking only Non-Firm Contract Demand Transmission Service, 
the reserved transmission service limit shall equal the approved Non-Firm Contract 
Demand Transmission Service minus any curtailed MW.  
For an Eligible Customer taking Firm Contract Demand and Non-Firm Contract Demand 
Transmission Services, the reserved transmission service limit shall equal the Firm 
Contract Demand Transmission Service plus the approved Non-Firm Contract Demand 
Transmission Service minus any curtailed MW.  
For an Eligible Customer taking Interim Network Integration Transmission Service, the 
reserved transmission service limit shall equal the Interim Network Integration 
Transmission Service demand minus any curtailed MW.
Each five-minute interval beginning with the first minute of each hour shall constitute a 
separate interval and each hour from 0100 through 2400 shall constitute a separate hour 
for purposes of determining whether one or more exceedances have occurred.
Page 115

PDF page 281

The base penalty charge shall be applied to each Exceedance Hour and shall be calculated as:
Hourly Exceedance MW × Equivalent Hourly Firm Contract Demand (“FCD”) rate × 
number of Exceedance Intervals within the hour
Where:
Hourly Exceedance MW = Maximum telemetered load during the hour – Reserved 
Transmission Service Limit for the hour
Equivalent Hourly FCD rate = FCD rate / 8,760 hours
Penalty Ratchet
A penalty rachet shall apply when multiple Exceedance Hours occur during a particular time 
period in order to escalate the penalty charges as the frequency of unreserved transmission use 
increases.  
If more than one Exceedance Hour occurs on the same calendar day, an additional daily 
penalty shall apply.  
If exceedances occur on multiple calendar days within the same calendar week, an 
additional weekly penalty shall apply. 
If exceedances occur in multiple calendar weeks within the same calendar month, an 
additional monthly penalty shall apply.
If exceedances occur in multiple calendar months within the same calendar year, an 
additional yearly penalty shall apply.  
The penalty ratchet shall be based on an Eligible Customer’s exceedance pattern and applies 
escalating FCD-equivalent rates as the frequency of unreserved transmission use increases.  
Depending on whether exceedances occur within the same calendar day, calendar week, calendar 
month, or calendar year, the penalty ratchet shall apply daily, weekly, monthly, or annual penalty 
charges, respectively, as follows: 
Exceedance Pattern
Penalty Rate Applied
Multiple Exceedance Hours in a single calendar day
Daily FCD-Equivalent Rate
Multiple Exceedance Days within a calendar week
Weekly FCD-Equivalent Rate
Multiple Exceedance Weeks within a calendar month
Monthly FCD-Equivalent Rate
Multiple Exceedance Months within a calendar year
FCD Annual Rate
Daily Penalty Charge
The Daily Penalty Charge is calculated as:
Maximum Hourly Exceedance MW during the calendar day
× Daily FCD Equivalent Rate
Page 116

PDF page 282

× Number of Exceedance Hours in the calendar day
Weekly Penalty Charge
The Weekly Penalty Charge is calculated as:
Maximum Hourly Exceedance MW during the calendar week
× Weekly FCD Equivalent Rate
× Number of Exceedance Days in the calendar week
Monthly Penalty Charge
The Monthly Penalty Charge is calculated as:
Maximum Hourly Exceedance MW during the calendar month
× Monthly FCD Equivalent Rate
× Number of Exceedance Weeks in the calendar months
Annual Penalty Charge
The Annual Penalty Charge is calculated as:
Maximum Hourly Exceedance MW during the calendar year
× Annual FCD Rate
× Number of Exceedance Months in the calendar year
Revenues collected from Financial Penalty Charges shall be credited to Eligible Customers 
taking Firm Contract Demand Transmission Service, Non-Firm Contract Demand Transmission 
Service, Network Integration Transmission Service, and Interim Network Integration 
Transmission Service.  The Transmission Provider shall return revenues collected from Financial 
Penalty Charges on a monthly and annual basis as bill credits to Eligible Customers taking Firm 
Contact Demand Service, Non-Firm Contract Demand Transmission Service, Network 
Integration Transmission Service, and Interim Network Integration Transmission Service, who 
were not assessed Financial Penalty Charges during the year based on each Eligible Customer’s 
pro rata share of the Zone’s annual peak load based on the most recent 12-month period ending 
October 31.  The Eligible Customer’s pro rata share shall be based on the ratio of its Zone 
Network Load, Firm Contract Demand Transmission Service Amount, and Non-Firm Contract 
Transmission Service Amount to the sum of Network Customer Loads in the Zone and Firm and 
Non-Firm Contract Demand Transmission Service Amounts for all Eligible Customers taking 
Firm and Non-Firm Contract Demand Transmission Service in the Zone, for the applicable peak 
period.
Page 117

PDF page 283

Exhibit No. PTO-0001 
Page 1 of 43 
UNITED STATES OF AMERICA 
BEFORE THE 
FEDERAL ENERGY REGULATORY COMMISSION 
Exelon Corporation, et al.
)  
Docket No. ER27-___-000 
DIRECT JOINT TESTIMONY 
OF 
PETER BLAZUNAS AND HANHAN HAMMER 
I. 
INTRODUCTION  
1 
Q.  
Please state your name, title, business address, and provide your professional 
2 
background and relevant experience. 
3 
A. 
[Blazunas] My name is Peter Blazunas, and my business address is 293 Boston Post Road 
4 
West, Marlborough, MA 01752.  I am a Vice President with Concentric Energy Advisors, 
5 
Inc (“Concentric”).  I joined Concentric in 2021, and I provide regulatory strategy and rate 
6 
case expertise to regulated electric and gas utilities, especially with respect to the topics of 
7 
cost of service and rate design.  Prior to Concentric, I managed a team overseeing the cost 
8 
of service, rate design, and rate administration functions for Potomac Electric Power 
9 
Company’s (“Pepco”) Maryland and District of Columbia jurisdictions.  Prior to Pepco, I 
10 
worked as an analyst in the FirstEnergy Corp. Rates and Regulatory Affairs department.  I 
11 
have testified before the Federal Energy Regulatory Commission (“FERC” or 
12 
“Commission”) as well as regulatory commissions in Delaware, the District of Columbia, 
13 
Maryland, Ohio, and Rhode Island.  
14 
[Hammer] My name is Hanhan Hammer, and my business address is 293 Boston 
15 
Post Road West, Marlborough, MA 01752.  I am a Senior Project Manager with 
16

PDF page 284

Exhibit No. PTO-0001 
Page 2 of 43 
Concentric.  In my current role, I advise regulators, utilities, grid operators, and project 
1 
developers on complex regulatory and market matters, with a particular focus on 
2 
transmission planning, cost allocation and cost recovery, and large load tariffs.  I also 
3 
advise clients on generation and large load interconnection rules, compliance with FERC 
4 
orders, wholesale market participation, and resource planning. 
5 
Prior to joining Concentric in 2024, I spent 15 years working at three Regional 
6 
Transmission Organizations/Independent System Operators. My experience includes 
7 
designing wholesale market rules, particularly wholesale pricing mechanisms at ISO New 
8 
England Inc. (“ISO-NE”), and overseeing competitive market performance and monitoring 
9 
activities at the Midcontinent Independent System Operator, Inc. (“MISO”) and Southwest 
10 
Power Pool, Inc. (“SPP”).  I have testified before FERC as well as the New Hampshire 
11 
Public Utilities Commission. 
12 
[Blazunas and Hammer] Our professional backgrounds and relevant experience 
13 
are provided in Exhibit No. PTO-0002.  
14 
II. 
BACKGROUND 
15 
Q. 
What is the background for this proceeding? 
16 
A. 
[Blazunas and Hammer] In this proceeding, the PJM Transmission Owners submitted for 
17 
filing revisions to the PJM Interconnection, L.L.C. (“PJM”) Open Access Transmission 
18 
Tariff (“Tariff”).  The proposed Tariff revisions establish rates, cost allocation and cost 
19 
recovery mechanisms, financial protections, revenue-crediting requirements, and 
20 
transparency measures associated with transmission service to be taken by Eligible 
21 
Customers on behalf of Co-Located Loads and Large Loads.  These revisions respond to 
22 
the Commission’s preliminary finding in its June 18, 2026 Order Instituting Proceeding 
23

PDF page 285

Exhibit No. PTO-0001 
Page 3 of 43 
Under Section 206 of the Federal Power Act in Docket No. EL26-67-000 (“Show Cause 
1 
Order”).  The proposed revisions also comply with the Commission’s June 18, 2026 Order 
2 
on Rehearing, Clarification, Compliance Filing and Paper Hearing in Docket Nos. EL25-
3 
49, et al. (“Co-Located Load Paper Hearing Order”).  The PJM Transmission Owners’ 
4 
filing consists of several key elements, which we address in detail in our testimony below.  
5 
These are:     
6 
1. 
Rates for transmission services available to Eligible Customers taking 
7 
service on behalf of Large Loads and Co-Located Loads.
8 
9 
The new services available to Eligible Customers taking service on behalf of Large Loads 
10 
and Co-Located Loads include: (i) Firm Contract Demand Transmission Service 
11 
(“FCDS”); (ii) Non-Firm Contract Demand Transmission Service (“NFCDS”); and (iii) 
12 
Interim Network Integration Transmission Service (“Interim NITS”). The Co-Located 
13 
Load Paper Hearing Order found the PJM Transmission Owners’ rate treatment proposals 
14 
for FCDS and Interim NITS just and reasonable.1  However, the Commission rejected the 
15 
PJM Transmission Owners’ proposed NFCDS maximum rate and required a lower 
16 
maximum rate or nondiscriminatory discounts supported by transparent calculations.  
17 
Accordingly, the PJM Transmission Owners’ filing implements the rate treatments already 
18 
found just and reasonable for FCDS and Interim NITS through compliance tariff records,2
19 
and proposes a revised NFCDS discounted rate methodology and related tariff provisions 
20 
in compliance with the Commission’s directives.3  The filing extends and adapts those rates 
21 
1
Co-Located Load Paper Hearing Order at PP 398, 572. 
2
Id. at PP 398, 400, 401. 
3
Id. at PP 400, 401, 412.

PDF page 286

Exhibit No. PTO-0001 
Page 4 of 43 
to Eligible Customers taking service on behalf of Large Loads based on the eligibility 
1 
criteria set forth in the filing PJM submits on this same date. 
2 
2. 
A pro forma Cost Recovery Agreement and related implementing 
3 
Tariff provisions.   
4 
5 
The pro forma Cost Recovery Agreement (“CRA”) and related Tariff provisions address 
6 
the Commission’s concerns regarding the lack of an adequate mechanism in the Tariff to 
7 
mitigate the risk of cost shifting among wholesale transmission customers.4  The pro forma
8 
CRA accomplishes this through imposing on Large Load customers a financially secured 
9 
minimum transmission-revenue contribution associated with the amount of firm 
10 
transmission service requested from PJM by an Eligible Customer on behalf of the Large 
11 
Load, along with a shortfall payment and crediting mechanism and financial security 
12 
obligations, in order to ensure that each customer’s minimum commitment is satisfied over 
13 
the term of the CRA.  The PJM Transmission Owners’ proposed pro forma CRA also 
14 
appropriately recognizes that voluntary cost recovery agreements and other ratepayer 
15 
protection mechanisms have been, and continue to be, utilized at the retail and wholesale 
16 
level by utilities within PJM.  It makes clear that Transmission Owners in PJM will 
17 
continue to be permitted to utilize existing as well as new consumer protection 
18 
arrangements, as alternatives to the pro forma CRA, so long as those arrangements result 
19 
in comparable protections and are accepted for filing by the Commission.5
20 
The pro forma CRA is a three-party agreement among the Transmission Owner, 
21 
the Large Load Customer, and the Eligible Customer that takes transmission service on the 
22 
4
Show Cause Order at PP 77-81. 
5
Proposed Tariff, Part VIII, Subpart N, sections 441(a)(ii), 441(e)(v).

PDF page 287

Exhibit No. PTO-0001 
Page 5 of 43 
Large Load’s behalf.  The Large Load Customer controls the project, so it bears the 
1 
payment and credit support obligations.  The Eligible Customer remains the transmission 
2 
customer, and the Transmission Owner administers the agreement and credits the amounts 
3 
it collects.  The Large Load must execute the CRA and post credit support before it can 
4 
proceed through PJM’s Fast Energization Process.  That up-front commitment is intended 
5 
to discourage speculative or duplicative requests.  The commitment is first set from the 
6 
Large Load’s expected demand and ramp schedule.  It is then updated after PJM’s study to 
7 
reflect when service can actually be provided, without financial penalty for that schedule 
8 
adjustment.6
9 
Once service begins, the Transmission Owner compares, at least once a year, the 
10 
revenue actually produced by the Large Load’s firm transmission service with a committed 
11 
minimum of 80 to 100 percent of the anticipated full-service revenue.  The Large Load 
12 
pays any shortfall, and that payment reduces the Transmission Owner’s revenue 
13 
requirement, thereby protecting other customers in the Transmission Owner’s zone against 
14 
the risk of cost shifting.7  If the project is cancelled or permanently reduced, the Large Load 
15 
pays a termination amount that increases as the project advances.  If termination occurs 
16 
before service begins – that payment is first applied to the Project Development Costs 
17 
associated with the transmission facilities needed to serve the Large Load, in accordance 
18 
with the Tariff’s allocation provisions.  Any remainder is credited against the transmission 
19 
6
Id. at section 441(d); Proposed pro forma Cost Recovery Agreement, Part IX, Subpart P at Preamble and 
Articles 3.1-3.2, 6.1. 
7
Id. at Articles 5.1-5.5, 7.6 and Exhibit B.

PDF page 288

Exhibit No. PTO-0001 
Page 6 of 43 
revenue requirements of the applicable Transmission Owners, reducing the amounts 
1 
otherwise recovered from transmission customers.8
2 
3. 
Tariff provisions addressing the recovery of the costs of transmission 
3 
upgrades necessary to provide transmission service to Large Loads and 
4 
interconnection service to generators on a combined study basis.
5 
6 
The Tariff revisions include a methodology for allocating and recovering the costs of 
7 
transmission upgrades, referred to as “Interconnection Reliability Reinforcements,” 
8 
resulting from PJM’s proposed Fast Energization Process.  The allocation methodology is 
9 
based on a modified version of PJM’s existing proportional impact allocation methodology 
10 
for customers in its New Service Request process.  Cost responsibility will be assigned to 
11 
those Zones containing Large Loads being studied for transmission service in the PJM Fast 
12 
Energization Process via a new Interconnection Reliability Reinforcement Charge 
13 
(“IRRC”).  The PJM Transmission Owners are also proposing a Generator Reliability 
14 
Reinforcement Fee (“GRRF”) that PJM will assess to generators in each Fast Energization 
15 
study cycle to recover a commercially reasonable portion of overall portfolio costs based 
16 
on each generator’s proportional impact on the reliability constraints mitigated by the 
17 
portfolio of Interconnection Reliability Reinforcements.  The GRRF revenues will be 
18 
credited to transmission customers in those Zones based on their allocation of IRRCs.9
19 
4. 
Transparency and customer protection commitments.   
20 
In addition to the basic cost allocation and rate design features of the PJM Transmission 
21 
Owners’ proposal, the PJM Transmission Owners are committing to make, on compliance, 
22 
8
Proposed Tariff, Part VIII, Subpart N, section 441(e); Proposed pro forma CRA, Part IX, Subpart P at Article 
9.12. 
9
Proposed Schedule 12, Sections (f)(1)-(6).

PDF page 289

Exhibit No. PTO-0001 
Page 7 of 43 
necessary changes to their formula rate templates to: (i) provide transparency to state 
1 
regulators and other interested parties regarding the costs of transmission facilities being 
2 
constructed by the Transmission Owner to provide transmission service to Large Loads; 
3 
and (ii) adopt a mechanism designed to protect wholesale transmission customers not 
4 
regulated at the retail level (municipals, cooperatives, and other applicable load-serving 
5 
entities) from having to bear excessive large-load-related transmission upgrade costs. 
6 
III.  
PURPOSE OF TESTIMONY 
7 
Q. 
What is the purpose of your testimony?  
8 
A.   
[Blazunas and Hammer] The purpose of this testimony is to describe and support certain 
9 
PJM Transmission Owners’ Tariff revisions submitted in response to the Show Cause 
10 
Order and Co-Located Load Paper Hearing Order.  Specifically, this testimony addresses 
11 
the proposed extension of new transmission services to Eligible Customers taking service 
12 
on behalf of flexible Large Loads; the proposed discounted rate for NFCDS; the recovery 
13 
of transmission-upgrade costs associated with Large Loads and generation; transparency 
14 
and customer-protection commitments; and the proposed CRA.  
15 
IV. 
EXTENSION OF APPROVED RATE DESIGN ELEMENTS TO LARGE LOAD-
16 
RELATED TRANSMISSION SERVICE REQUESTS 
17 
Q. 
Please describe the PJM Transmission Owners’ proposal to extend the rates and 
18 
financial penalty framework approved with respect to new transmission services for 
19 
Co-Located Loads to Eligible Customers taking service on behalf of Large Loads.  
20 
A.  
[Blazunas] In the Show Cause Order, the Commission expressed concerns that “PJM’s 
21 
tariff does not include transmission services that reflect the use of the transmission system 
22 
by Eligible Customers on behalf of flexible large load, on both an interim and permanent 
23

PDF page 290

Exhibit No. PTO-0001 
Page 8 of 43 
basis.”10  In its filing in response to the Show Cause Order, PJM is proposing to extend the 
1 
new transmission services (FCDS, NFCDS, and Interim NITS) to Eligible Customers 
2 
taking service on behalf of Large Load customers, in addition to Co-Located Load.  
3 
Consequently, the PJM Transmission Owners propose to extend the rates and financial 
4 
penalty framework for unreserved transmission system use developed for Co-Located Load 
5 
and approved by the Commission in the Co-Located Load Paper Hearing Order to Eligible 
6 
Customers taking service on behalf of Large Loads.  Accordingly, the PJM Transmission 
7 
Owners propose to extend the approved rates for FCDS and Interim NITS to Eligible 
8 
Customers taking service on behalf of Large Loads.11  The PJM Transmission Owners also 
9 
propose to extend their new proposed rate design for NFCDS, as discussed below, to 
10 
Eligible Customers on behalf of Large Loads.    
11 
The PJM Transmission Owners’ proposal to extend these services to all eligible 
12 
large load customers is consistent with the “operational reality that large loads may use the 
13 
transmission system to differing extents and certain large loads are willing and able to limit 
14 
their use of the transmission system under certain conditions.”12  These services are 
15 
functionally identical to the services developed for Co-Located Loads.  Therefore, it is 
16 
reasonable that the same rate design approach should apply to Eligible Customers seeking 
17 
one or more of these new services on behalf of either Co-Located Load or Large Load. 
18 
19 
10
Show Cause Order at P 87. 
11
Proposed Tariff, Part XI, Subpart A, Section 706; Tariff, Part XI, Subpart C, Section 714; and Proposed 
Schedules 20 and 22. 
12
Show Cause Order at P 86.

PDF page 291

Exhibit No. PTO-0001 
Page 9 of 43 
V. 
PROPOSED RATE FOR NON-FIRM CONTRACT DEMAND TRANSMISSION 
1 
SERVICE 
2 
Q.  
Please describe the Commission’s determination with respect to the PJM 
3 
Transmission Owners original proposal for Non-Firm Contract Demand Service 
4 
rates.  
5 
A.  
[Blazunas] In the Co-Located Load Paper Hearing Order, the Commission rejected the 
6 
PJM Transmission Owners’ original proposal to charge the same maximum rate for both 
7 
FCDS and NFCDS, and directed the PJM Transmission Owners to submit a compliance 
8 
filing with revised rates for NFCDS.13  Specifically, the Commission directed the PJM 
9 
Transmission Owners to propose a lower maximum rate or non-discriminatory discounts 
10 
for the revised NFCDS.14 In addition, the Commission directed the PJM Transmission 
11 
Owners to ensure that the revised rates for NFCDS are transparent with respect to how they 
12 
will be calculated for individual customers.15
13 
Q.  
Please describe the PJM Transmission Owners’ revised proposal for NFCDS rates.  
14 
A.  
[Blazunas] The PJM Transmission Owners propose a discounted NFCDS rate using a 
15 
reservation rate set by Zone and that is a function of the zonal FCDS rate (i.e., the NFCDS 
16 
maximum rate) and the transmission system load factor for a Zone.  In short, the discounted 
17 
NFCDS rate for a given Zone is calculated as the zonal FCDS rate multiplied by the 
18 
transmission system load factor for the Zone.16  The transmission system load factor is 
19 
13
Co-Located Load Paper Hearing Order at PP 402, 404, 412. 
14
Id. at P 412. 
15
Id. 
16
Proposed Tariff, Part XI, Subpart C, Section 715 and Proposed Schedule 21.

PDF page 292

Exhibit No. PTO-0001 
Page 10 of 43 
calculated as annual zonal energy divided by the product of zonal peak demand for an 
1 
annual period multiplied by 8,760 hours.  An example calculation of the proposed 
2 
discounted NFCDS rate is provided below: 
3 
Table 1: Example Calculation of Discounted Non-Firm Contract Demand Transmission 
Service Rate 
Component 
Calculation 
Amount 
(a) Zonal Firm Contract Demand Rate ($/MW-Year)
$90,000
(b) Zonal Peak Demand (MW)
150,000
(c) Zonal Annual Energy (MWh)
850,000,000
(d) Hours Per Year
8,760
(e) Zonal Discounted Non-Firm Contract Demand Rate 
($/MW-Year)
= (a) x [(c) ÷ ((b) x (d))] 
$58,219 
(f) Implied Discount to Maximum Rate
= 1 – [(e) ÷ (a)]
35.3%
The underlying rationale for this methodology is the fact that the transmission system is 
4 
built to accommodate a peak demand that is driven by firm load.  The difference between 
5 
actual zonal annual energy and zonal annual energy at a 100 percent load factor represents 
6 
a reasonable proxy for the “excess capacity” for which non-firm load is arguably not 
7 
responsible.  A lower system load factor for a Zone indicates relatively more “excess 
8 
capacity” and justifies a higher discount for non-firm load’s use of that “excess capacity,” 
9 
and vice-versa.  The PJM Transmission Owners’ proposal meets the directives that the 
10 
Commission set forth in the Co-Located Load Paper Hearing Order insofar as it results in 
11 
a non-discriminatory and transparent discount for NFCDS for each PJM Zone that can be 
12 
calculated using publicly available data.  
13 
14 
15 
16 
17

PDF page 293

Exhibit No. PTO-0001 
Page 11 of 43 
VI. 
ALLOCATION AND RECOVERY OF COSTS ASSOCIATED WITH UPGRADES 
1 
IDENTIFIED IN PJM’S FAST ENERGIZATION PROCESS 
2 
 A. 
Summary of Cost Allocation and Recovery 
3 
Q. 
Why are the PJM Transmission Owners proposing a new cost allocation methodology 
4 
as part of the response to the Commission’s Show Cause Order? 
5 
A. 
[Hammer] The Transmission Owners are proposing a new cost allocation framework 
6 
because PJM’s proposed Fast Energization Process will study Large Load transmission 
7 
service requests in the same study cycle as existing New Service Requests, including 
8 
generation and long-term firm transmission service requests.  These different service 
9 
requests will result in a single overall portfolio of projects needed to address the reliability 
10 
constraints identified through PJM’s Fast Energization Process, as opposed to a process in 
11 
which specific projects are attributable to specific service requests.  Therefore, a 
12 
methodology is needed to allocate the costs of the transmission facilities, known as 
13 
“Interconnection Reliability Reinforcements,” required to resolve those constraints. 
14 
PJM’s existing interconnection cost allocation procedures were not designed to 
15 
allocate the costs of a single cohesive portfolio of transmission facilities resulting from a 
16 
study process involving both generation interconnection requests and transmission service 
17 
requests made by Eligible Customers on behalf of Large Loads.  The PJM Transmission 
18 
Owners have therefore developed a proportional impact assessment framework based on 
19 
PJM’s existing proportional impact allocation methodology for New Service Requests.  
20 
This framework measures each request’s relative contribution to the identified reliability 
21

PDF page 294

Exhibit No. PTO-0001 
Page 12 of 43 
constraints and uses those impacts to allocate the costs of the resulting Interconnection 
1 
Reliability Reinforcements.17
2 
Q. 
What are Interconnection Reliability Reinforcements, and why is it necessary to 
3 
establish a specific methodology for allocating the costs of those facilities? 
4 
A. 
[Hammer] Interconnection Reliability Reinforcements are the transmission facilities 
5 
identified by PJM through the Fast Energization Process as necessary to address reliability 
6 
violations associated with the generation interconnection requests and transmission service 
7 
requests made by Eligible Customers on behalf of Large Loads that PJM examines in the 
8 
cluster study.  Because those reliability violations may result from the combined impacts 
9 
of generator and Large Load requests, it is necessary to establish a methodology that 
10 
assigns cost responsibility based on each request’s contribution to the identified reliability 
11 
constraints, rather than by allocating the costs of  individual upgrades to individual 
12 
requests. 
13 
Q.  
Please provide an overview of the cost recovery provisions proposed by the PJM 
14 
Transmission Owners in this filing. 
15 
A.  
[Blazunas] Under the PJM Transmission Owners’ cost allocation methodology, cost 
16 
responsibility for Interconnection Reliability Reinforcements will be determined using a 
17 
modified version of PJM’s proportional impact methodology and initially assigned to those 
18 
Zones containing Large Loads being studied for transmission service in the PJM Fast 
19 
Energization Process.  Those costs will be included in the rate base of the Transmission 
20 
Owners designated to construct and own the Interconnection Reliability Reinforcements 
21 
17
Proposed Schedule 12, Sections (f)(1)-(2).

PDF page 295

Exhibit No. PTO-0001 
Page 13 of 43 
and recovered from transmission customers in the applicable Zones through a new IRRC 
1 
assessed based on the calculated impact of the Large Loads within the Zones.  This 
2 
allocation methodology will apply to all portfolios of Interconnection Reliability 
3 
Reinforcements identified through PJM’s Fast Energization Process for 15 years, after 
4 
which the remaining costs of the upgrade will be subject to regional allocation using the 
5 
then-current Schedule 12 methodology that applies to Regional Transmission Expansion 
6 
Plan (“RTEP”) reliability projects.   
7 
Under the PJM Transmission Owners’ proposal, generators in the Fast Energization 
8 
Process will pay a fee, referred to as the Generator Reliability Reinforcement Fee (or 
9 
GRRF), representing their appropriate share of the costs of the Interconnection Reliability 
10 
Reinforcement portfolio, to be billed and collected by PJM over a 15-year period.  In order 
11 
to provide certainty to generators as early in the process as possible, the GRRF will be 
12 
calculated at the end of the PJM Fast Energization study process based on the estimated 
13 
costs of the Interconnection Reliability Reinforcements available at that time, along with 
14 
an appropriate carrying charge calculation.  Revenues collected by PJM via the GRRF will 
15 
be credited to transmission customers in the Zones that have been assigned cost 
16 
responsibility for the relevant Interconnection Reliability Reinforcements.  Likewise, 
17 
IRRCs assessed to external Zones based on the calculated impact of Large Loads within 
18 
the Zones will be credited to firm transmission customers in the Zones where the 
19 
Interconnection Reliability Reinforcements are located.  The practical impact of this 
20 
crediting approach is that it ensures that no customer pays twice for the same facilities.  
21 
In addition to the basic cost allocation and rate design features of the PJM 
22 
Transmission Owners’ proposal, the PJM Transmission Owners are committing to make, 
23

PDF page 296

Exhibit No. PTO-0001 
Page 14 of 43 
on compliance, necessary changes to their respective formula rate templates to: (1) provide 
1 
transparency to state regulators and other interested parties regarding the costs of 
2 
transmission facilities being constructed by the Transmission Owner to provide 
3 
transmission service to Large Loads; and (2) adopt a mechanism designed to protect 
4 
wholesale transmission customers not regulated at the retail level (municipals, 
5 
cooperatives, and other applicable load-serving entities) from having to bear excessive 
6 
large-load-related transmission upgrade costs. 
7 
B. 
Proportional Impact Methodology 
8 
Q. 
What is the proportional impact methodology? 
9 
A. 
[Hammer] A proportional impact allocation methodology is a cluster-based cost allocation 
10 
framework that determines the relative contribution to a portfolio of shared transmission 
11 
upgrades based on a customer’s quantified impact on identified transmission constraints.  
12 
Specifically, applied to the Fast Energization Process, it evaluates how much each 
13 
generator interconnection request and transmission service request made by an Eligible 
14 
Customer on behalf of a Large Load impacts the aggregate reliability constraints addressed 
15 
by a portfolio of Interconnection Reliability Reinforcements.  Each request’s impacts are 
16 
then weighted and aggregated to determine its proportional impact on the constraints 
17 
driving the need for the Interconnection Reliability Reinforcement portfolio.18
18 
19 
20 
18
Proposed Schedule 12, Section (f)(2)(A)-(C).

PDF page 297

Exhibit No. PTO-0001 
Page 15 of 43 
Q. 
Why is a proportional impact methodology appropriate for determining 
1 
Interconnection Reliability Reinforcement cost allocation and the resulting charges?
2 
A. 
[Hammer] A proportional impact methodology is appropriate because it establishes an 
3 
engineering-based relationship between each request’s contribution to the reliability 
4 
constraints and the allocation of the costs of the Interconnection Reliability Reinforcements
5 
needed to address these constraints.  Unlike an allocation based on project size or requested 
6 
MWs of service, the proportional impact methodology measures the extent to which the 
7 
generation interconnection and Large Load transmission service requests impact the 
8 
underlying reliability needs and the resulting portfolio of Interconnection Reliability 
9 
Reinforcements.  This aligns cost allocation and recovery with the principle of cost 
10 
causation.  This approach is also consistent with the proportional impact approach reflected 
11 
in FERC Order No. 2023 for allocating the costs of certain shared Network Upgrades.19
12 
Q. 
How are the proportional impacts calculated? 
13 
A. 
[Hammer] The Transmission Owners’ proposal uses violation-based distribution factors 
14 
(“DFAX”) to measure the relative impacts of generation and Large Load requests on the 
15 
reliability constraints identified in a cluster study.  For identified constraints, PJM would 
16 
first calculate a DFAX, representing the percentage of an energy transfer that flows across 
17 
a constrained facility.  For a generator, the applicable DFAX is multiplied by the MW 
18 
capacity studied in the Fast Energization Process to determine the generator’s MW impact 
19 
on the constrained facility.  For a Large Load, the applicable DFAX is multiplied by the 
20 
19
See Improvements to Generator Interconnection Procs. and Agreements, Order No. 2023, 184 FERC ¶ 
61,054, at PP 455, 486 (2023), order on reh’g, Order No. 2023-A, 186 FERC ¶ 61,199 (2024).

PDF page 298

Exhibit No. PTO-0001 
Page 16 of 43 
MW amount of Firm Transmission Service requested.  Only impacts that exceed the 
1 
applicable thresholds specified in the PJM Manuals are included in the allocation.20
2 
The qualifying impacts for each request are then converted into proportional MW 
3 
impacts representing the pro rata share of all MW impacts on the same constrained 
4 
facility.21  Those proportional MW impacts are weighted and aggregated to develop each 
5 
request’s share of the overall portfolio of Interconnection Reliability Reinforcements. 
6 
Q. 
Why does the proposal weigh and aggregate impacts across constrained facilities?
7 
A. 
[Hammer] Weighting is necessary because a MW of impact on one constrained facility 
8 
does not necessarily have the same transmission investment significance as a MW of 
9 
impact on another.  For example, a 1 MW impact on a 20-mile, 138 kV constrained facility 
10 
may have materially different transmission investment implications than a 1 MW impact 
11 
on a 150-mile, 500 kV constrained facility.  Simply adding those MW impacts on an 
12 
unweighted basis could therefore treat materially different transmission impacts as 
13 
equivalent.  Weighting is intended to place impacts across different constrained facilities 
14 
on a reasonably comparable basis before they are aggregated.  The detailed weighting 
15 
methodology will be developed by the PJM Transmission Owners, specified in the PJM 
16 
Manuals, and applied consistently to all requests studied through the Fast Energization 
17 
Process.
18 
Aggregation is necessary because a single request may contribute to violations on 
19 
multiple constrained facilities.  The proposal aggregates the request’s weighted impacts 
20 
20
Proposed Schedule 12, Section (f)(2)(A)(3). 
21
Id. at Section (f)(2)(A)(4).

PDF page 299

Exhibit No. PTO-0001 
Page 17 of 43 
across constrained facilities to develop a measure of its overall contribution to the 
1 
reliability needs addressed by the Interconnection Reliability Reinforcement portfolio.22
2 
Q.
How does the proposed proportional impact methodology differ from PJM’s existing 
3 
interconnection cost allocation approach detailed in Manual 14H? 
4 
A. 
[Hammer] The proposed methodology builds on concepts used in PJM’s existing 
5 
interconnection cost allocation methodology detailed in Manual 14H, including the use of 
6 
DFAX, MW impacts, applicable thresholds, and proportional contribution to reliability 
7 
violations.  The key difference is that the proposed methodology for allocating the costs of 
8 
Interconnection Reliability Reinforcements determines cost responsibility at the portfolio 
9 
level rather than on a facility-by-facility basis.  Because the Fast Energization Process 
10 
develops a portfolio of Interconnection Reliability Reinforcements to address the aggregate 
11 
reliability constraints identified in the cluster study, each request’s qualifying impacts 
12 
across those constraints are weighted and aggregated to establish its proportional impact 
13 
on the constraints addressed by the Interconnection Reliability Reinforcement portfolio.  
14 
Thus, the proposal preserves the existing impact-based approach while adapting it to a 
15 
portfolio-based reliability solution.23
16 
Q.
Why is a portfolio approach appropriate for the Fast Energization Process?
17 
A. 
[Hammer] A portfolio approach is appropriate because the Fast Energization Process 
18 
develops a portfolio of upgrades to address reliability violations resulting from the 
19 
combined impacts of generator interconnection and transmission service requests, rather 
20 
22
Id. at Section (f)(2)(C). 
23
Id. at Section (f)(2)(A)-(C).

PDF page 300

Exhibit No. PTO-0001 
Page 18 of 43 
than assigning individual upgrades directly to individual requests.  The proposed 
1 
methodology therefore determines each request’s relative contribution to the need for the 
2 
Interconnection Reliability Reinforcement portfolio as a whole.24
3 
Q.       Can you provide a simple example to illustrate the proposed proportional impact 
4 
methodology?
5 
A.        [Hammer] Yes.  Assume that a PJM Fast Energization Process Cycle includes two requests: 
6 
a 200 MW generation interconnection request, which I will refer to as Gen 1, and 300 MW 
7 
Large Load transmission service request, which I will refer to as Load 1.   
8 
The first step is to determine the extent to which each request impacts the identified 
9 
constrained facilities.  For purposes of this simplified example, the impact is calculated by 
10 
multiplying each request’s MW quantity by its DFAX on each constrained facility.  For 
11 
example, Gen 1 has an 8 percent DFAX on Facility 1.  Multiplying its 200 MW request by 
12 
8 percent results in a 16 MW impact on Facility 1. 
13 
14 
Constrained 
Facilities
Gen 1 DFAX
Load 1 
DFAX
Gen 1 MW 
Impact
Load 1 MW 
Impact
Total MW 
Impact 
Facility 1
8%
0%
16
0
16 
Facility 2
4%
9%
8
27
35 
Facility 3
0%
6%
0
18
18 
15 
The MW impacts are then converted to proportional impact on each constrained 
16 
facility based on the pro rata shares of their MW impact on the constrained facility. 
17 
18 
24
Id. at Section (f)(2)(C).

PDF page 301

Exhibit No. PTO-0001 
Page 19 of 43 
Constrained 
Facilities
Gen 1 
Proportional 
Impact  
Load 1 
Proportional 
Impact
Facility 1
100.00%
0.00%
Facility 2
22.86%
77.14%
Facility 3
0.00%
100.00% 
1 
The next step is to apply a weighting factor that reflects the relative characteristics 
2 
of each constrained facility.  In this example, the weighting factor is based on the product 
3 
of the facility’s voltage and line length, expressed as kV-miles. Facility 1, with the lowest 
4 
kV-mile value, is assigned a weighting factor of 1.00, and the other facilities are weighted 
5 
relative to Facility 1.25
6 
Constrained Facilities
Voltage (kV)
Miles
kV x Miles
Weighting Factor
Facility 1
138
30
4,140
1.00
Facility 2
345
20
6,900
1.67
Facility 3
500
100
50,000
12.08
7 
These weighting factors are then applied to each request’s unweighted proportional 
8 
impact on each constrained facility.
9 
Constrained 
Facilities
Weighting 
Factor
Gen 1 
Proportional 
Impact
Load 1 
Proportional 
Impact
Gen 1 
Weighted 
Proportional 
Impact
Load 1 
Weighted 
Proportional 
Impact
Facility 1
1.00
1.00 
0.00 
1.00 
0.00 
Facility 2
1.67
0.23 
0.77 
0.38 
1.29 
Facility 3
12.08
0.00 
1.00 
0.00 
12.08 
Portfolio 
Total
- 
- 
- 
1.38 
13.37 
10 
25
It is important to note that this specific calculation is provided for illustrative purposes.  The PJM 
Transmission Owners intend to propose a methodology for determining these weighting factors in future filings.

PDF page 302

Exhibit No. PTO-0001 
Page 20 of 43 
Each request’s weighted proportional impact on the constrained facility is summed 
1 
to calculate its portfolio weighted proportional impact.  The portfolio cost allocator for 
2 
each request is then calculated by dividing that request’s portfolio weighted proportional 
3 
impact by the total portfolio weighted proportional impact of all requests in the portfolio.   
4 
The resulting allocation percentages are then used to determine the applicable IRRCs and 
5 
GRRFs for recovery of the costs of the portfolio of Interconnection Reliability 
6 
Reinforcements.26
7 
Gen 1
Load 1
Portfolio Weighted Proportional Impact
1.38
13.37
Portfolio Cost Allocator (%)
9.37%
90.63%
8 
Q. 
Please provide a simple example of this transmission cost recovery construct. 
9 
A.  
[Blazunas] Assume that a study cycle of the PJM Fast Energization Process identifies 
10 
Interconnection Reliability Reinforcements necessary to provide service to a group of 
11 
generator interconnection requests and transmission service requests made by Eligible 
12 
Customers on behalf of Large Loads.  These Interconnection Reliability Reinforcements 
13 
ultimately cost $100 million to construct.  The full $100 million investment would be 
14 
included in the transmission revenue requirements of the Transmission Owners that are 
15 
designated to construct and own the Interconnection Reliability Reinforcements.  This 
16 
amount would be billed and recovered via IRRCs assessed to transmission customers in 
17 
PJM Zones based on the calculated impact of Large Loads within those Zones.27
18 
26
Proposed Schedule 12, Section (f)(2)(A), (C). 
27
Id. at Sections (f)(2)(C), (f)(3)–(4).

PDF page 303

Exhibit No. PTO-0001 
Page 21 of 43 
Assume also that at the end of the relevant Fast Energization Process study, the 
1 
Interconnection Reliability Reinforcements were estimated to cost $90 million, and the 
2 
proportional impacts of the generators in the cycle represented 40 percent of the overall 
3 
impacts.  This would result in PJM calculating GRRFs for each of the generators equal to 
4 
$36 million (40 percent of $90 million), along with the applicable carrying charge, and 
5 
billing those amounts to the applicable generators once they enter service.28
6 
Revenues from both the GRRFs and the IRRCs would be returned in the form of 
7 
credits to other transmission customers.  Specifically, GRRF revenues collected by PJM 
8 
would be credited back to transmission customers in the Zones assigned cost responsibility 
9 
for the Interconnection Reliability Reinforcements through the IRRC.  Likewise, IRRC 
10 
revenues collected by PJM would be credited to firm transmission customers in the 
11 
applicable Zones where the Interconnection Reliability Reinforcements are located.  This 
12 
approach ensures that the various costs are allocated in a manner that is roughly 
13 
commensurate with the benefits of the overall portfolio of Interconnection Reliability 
14 
Reinforcements, while preventing double recovery by the Transmission Owners that own 
15 
the Interconnection Reliability Reinforcements and are including them in their rate bases.29
16 
Q. 
How does the PJM Transmission Owners’ proposal address short-circuit constraints? 
17 
A. 
[Hammer] The proposal measures each request’s contribution to fault current relative to 
18 
the interrupting capability of the circuit breaker, consistent with PJM’s existing 
19 
methodology.  
20 
28
Id. at Section (f)(6)(B)-(C). 
29
Id. at Sections (f)(5), (f)(6)(D).

PDF page 304

Exhibit No. PTO-0001 
Page 22 of 43 
Although the engineering measure differs, the underlying cost allocation principle 
1 
is the same: the methodology applies an engineering metric appropriate to each type of 
2 
reliability constraint to measure each request’s relative contribution to the underlying 
3 
reliability need, thereby aligning cost responsibility with cost causation. 
4 
Q. 
In your opinion, is the proportional impact methodology appropriate? 
5 
A. 
[Hammer] The proportional impact methodology is appropriate because it builds on the 
6 
proportional impact approach already used in PJM’s existing New Service Request 
7 
framework and is consistent with the cost allocation principles reflected in FERC Order 
8 
No. 2023.  For reliability constraints, the methodology uses violation-based DFAX to 
9 
measure the relative contribution of each generation and Large Load request to the 
10 
identified constraints and uses those relative impacts as the basis for both the IRRCs and 
11 
GRRFs.30  It therefore aligns with cost causation principles, as I understand them, by 
12 
allocating and recovering costs based on each request’s contribution to the underlying need 
13 
being addressed.  The proposal adapts an established, engineering-based approach that 
14 
accounts for the fact that generation and Large Load requests are studied together and the 
15 
reliability solution consists of an integrated portfolio of Interconnection Reliability 
16 
Reinforcements. 
17 
18 
19 
20 
21 
30
Id. at Section (f)(2)(A), (C).

PDF page 305

Exhibit No. PTO-0001 
Page 23 of 43 
C. 
Generator Reliability Reinforcement Fee 
1 
Q.  
Please describe the PJM Transmission Owners’ proposed Generator Reliability 
2 
Reinforcement Fee. 
3 
A.  
[Blazunas] As noted above, the PJM Transmission Owners are proposing a GRRF  
4 
calculated to recover an appropriate portion of the Interconnection Reliability 
5 
Reinforcements from Generator Interconnection Customers in each PJM Fast Energization 
6 
Process Cycle.  The GRRF will be calculated after each System Impact Study Phase as part 
7 
of the PJM Fast Energization Process based on the following formula: 
8 
GRRF = GCAP x TRRGP x {[ACCC X (1 + ACCC)15]÷[(1 + ACCC)15 – 1]}31
9 
In this calculation, the GRRF is equal to the product of the Generator Interconnection 
10 
Customer’s Allocated Percentage (or “GCAP”), the Total Reliability Reinforcement Gross 
11 
Plant (or “TRRGP”), and the annualization factor for recovering an investment over a 15-
12 
year period, which itself includes the Annual Carrying Charge Component (or “ACCC”).  
13 
The GCAP represents the Generator Interconnection Customer’s proportional impact on 
14 
the portfolio of Interconnection Reliability Reinforcements in the relevant Cycle.  The 
15 
TRRGP represents the estimated gross plant of all Interconnection Reliability 
16 
Reinforcements approved by the PJM Board with respect to the relevant Cycle and for 
17 
which the Generator Interconnection Customer has been determined to have an impact per 
18 
the GCAP calculation.  This estimate is determined at the end of the applicable System 
19 
Impact Study Phase.  The ACCC represents the weighted average of the Weighted Average 
20 
Costs of Capital for all Transmission Owners with Interconnection Reliability 
21 
31
Id. at Section (f)(6)(B).

PDF page 306

Exhibit No. PTO-0001 
Page 24 of 43 
Reinforcements included in the RTEP approved by the PJM Board with respect to the New 
1 
Service Request Cycle that contains the Generator Interconnection Customer.32  The GRRF 
2 
is calculated as an annual amount that will be recovered by PJM via a monthly charge.33
3 
Revenues received from the GRRF will, as discussed above, be credited to firm 
4 
transmission customers in each Zone on a pro rata basis as described in the Tariff.34
5 
Q.  
Please describe the underlying rationale for the PJM Transmission Owners’ proposed 
6 
Generator Reliability Reinforcement Fee. 
7 
A.  
[Blazunas] As designed, the proposed Generator Reliability Reinforcement Fee ensures 
8 
that Generator Interconnection Customers bear an appropriate share of the costs incurred 
9 
to serve them, while also ensuring commercial feasibility by limiting the term over which 
10 
those costs are recovered as well as providing the Generator Interconnection Customer with 
11 
upfront certainty as to the size of the required payment.  The use of a 15-year period for 
12 
the term of the GRRF balances the longer life of the associated transmission assets 
13 
constructed to serve the Generator Interconnection Customer with consideration of the fact 
14 
that the payment should not be so long as to place excessive financial burdens on 
15 
generators.  This latter need is particularly relevant in the current environment where, 
16 
especially in PJM, capacity is short and the need for additional capacity is acute.  This 15-
17 
32
For purposes of calculating such weighted average, each applicable Transmission Owner’s Weighted 
Average Cost of Capital shall be weighted based on the ratio of the final estimated costs of the Interconnection 
Reliability Reinforcements that it has been designated to construct and own to the final estimated costs for all 
Interconnection Reliability Reinforcements.  See Proposed Schedule 12, Section (f)(6)(B). 
33
Id. at Section (f)(6)(C). 
34
Id. at Section (f)(6)(D).

PDF page 307

Exhibit No. PTO-0001 
Page 25 of 43 
year payment period also harmonizes with the 15-year allocation transition mechanism I 
1 
mentioned above and discuss in greater detail below.35
2 
Finally, the Annual Carrying Charge component of the calculation ensures that 
3 
Transmission Owners, and their customers, are fairly compensated for the carrying costs 
4 
associated with the Interconnection Reliability Reinforcement investment.  The Annual 
5 
Carrying Charge is based on the applicable Transmission Owners’ Weighted Average Cost 
6 
of Capital.36  Again, this approach strikes an appropriate balance between recovering a fair 
7 
portion of the costs of Interconnection Reliability Reinforcements from generators without 
8 
imposing an excessive commercial burden that would disincentivize generation investment 
9 
in PJM. 
10 
D. 
Interconnection Reliability Reinforcement Charge and Cost Allocation 
11 
Transition Mechanism 
12 
13 
Q. 
Please explain the Interconnection Reliability Reinforcement Charge. 
14 
A. 
[Blazunas] As I indicated earlier, the costs of Interconnection Reliability Reinforcements 
15 
will be included in the rate base of the Transmission Owners designated to construct and 
16 
own the Interconnection Reliability Reinforcements.  However, these costs will be 
17 
allocated and recovered from transmission customers throughout PJM through the IRRC. 
18 
PJM will calculate and assess the IRRC based on the proportional impact of the Large 
19 
Loads within each Zone and the revenue requirements for the Interconnection Reliability 
20 
35
Proposed Schedule 12, Sections (f)(3), (f)(6)(B)-(C). 
36
Id. at Section (f)(6)(B).

PDF page 308

Exhibit No. PTO-0001 
Page 26 of 43 
Reinforcements as determined by the Transmission Owners owning those facilities, based 
1 
on their formula rate templates.37
2 
Q. 
How will the revenues associated with Interconnection Reliability Reinforcement 
3 
Charges be treated? 
4 
A. 
[Blazunas] Revenues associated with IRRCs collected by PJM will be credited back to the 
5 
Zones in which the Interconnection Reliability Reinforcements are located and included in 
6 
Transmission Owner rate base.  This avoids any issue with potential double recovery.38
7 
Q. 
Is there any existing analogue in PJM to the Interconnection Reliability 
8 
Reinforcement Charge? 
9 
A. 
[Blazunas] Yes, the manner in which the IRRC is determined and recovered is very similar 
10 
to the existing Transmission Enhancement Charge (“TEC”), which PJM calculates and 
11 
bills in order to recover the costs of transmission upgrades identified in the PJM RTEP and 
12 
allocated regionally.  As with the TEC, the IRRC will be determined based on allocation 
13 
factors established pursuant to a formula set forth in Schedule 12 of the Tariff along with 
14 
the revenue requirements associated with the upgrades as determined by the applicable 
15 
Transmission Owners using their formula rate templates.  Moreover, revenues collected by 
16 
PJM pursuant to the IRRC, just like the TEC, will be credited back to transmission 
17 
customers in the Zones where the upgrades are located, so as to avoid potential double 
18 
recovery due to the fact that both regionally-allocated RTEP projects and Interconnection 
19 
37
Id. at Sections (f)(2)(C), (f)(3)-(4). 
38
Id. at Section (f)(5).

PDF page 309

Exhibit No. PTO-0001 
Page 27 of 43 
Reliability Reinforcements will be included in Transmission Owners’ transmission rate 
1 
base.39
2 
Q. 
Will the costs of Interconnection Reliability Reinforcements be allocated and 
3 
recovered based on the Interconnection Reliability Reinforcement Charge over the 
4 
entire life of the assets? 
5 
A. 
[Blazunas] No.  The PJM Transmission Owners propose to allocate and recover the costs 
6 
of Interconnection Reliability Reinforcements using the IRRC mechanism for a period of 
7 
15 years after they enter service.  After 15 years, the remaining costs of Interconnection 
8 
Reliability Reinforcements shall be allocated and recovered pursuant to the existing 
9 
regional cost allocation methodology set forth in Schedule 12.  That methodology relies on 
10 
a combination of solution-based DFAX and load-ratio share allocation approaches 
11 
depending on the type of upgrade at issue.40
12 
Q. 
Please explain why the PJM Transmission Owners are proposing a 15-year transition 
13 
period for allocating the costs of Interconnection Reliability Reinforcements. 
14 
A. 
[Blazunas] The use of a 15-year allocation period recognizes the fact that the topology of 
15 
the transmission system changes over time in terms of both load and generation, meaning 
16 
that over time, more customers will be benefitting from the use of the Interconnection 
17 
Reliability Reinforcements.  For instance, as shown in Section (I) of Exhibit No. PTO-
18 
0003, the 2026 PJM Load Forecast Report reflects a wide range of rates of growth of 
19 
summer and winter peak load across Zones over a 15-year period, with the Dominion 
20 
39
Id. at Sections (f)(2)(C), (f)(4)-(5). 
40
Id. at Section (f)(3).

PDF page 310

Exhibit No. PTO-0001 
Page 28 of 43 
Virginia Power zone forecast to have annualized 15-year summer and winter peak load 
1 
growth rates of 4.90 percent and 4.70 percent, respectively.41  The overall PJM Regional 
2 
Transmission Organization is forecast to have annualized 15-year summer and winter peak 
3 
load growth rates of 2.90 percent and 3.30 percent, respectively.  As load grows and more 
4 
transmission facilities are added to the system, those facilities will increasingly be used by 
5 
and relied on, and therefore benefit, customers across the region.   
6 
Similarly, the generation characteristics of the PJM system have undergone 
7 
significant changes over the past fifteen years.  Section (II) of Exhibit No. PTO-0003 
8 
presents existing MW capacity in PJM by zone between December 31, 2011, and 
9 
September 30, 2026.  Between the end of 2011 and the end of the third quarter of 2026, 
10 
PJM saw existing capacity increase by 2.5 percent overall.  This overall increase, however, 
11 
does not reflect the wide variation in the change in existing capacity in individual zones 
12 
across that same period.  For instance, the Dominion Virginia Power zone saw existing 
13 
capacity increase by 38 percent across that period whereas the Dayton Power & Light zone 
14 
saw its equivalent figure decrease by 71 percent.  The ability of both load and generation 
15 
to change significantly across these periods supports the idea that the transmission system 
16 
is dynamic and, consequently, transmission assets constructed to primarily serve one set of 
17 
customers today can reasonably be expected to benefit other customers in the future.  These 
18 
changes in the topology of the transmission system reduce the meaningfulness of constraint 
19 
impacts measured at a single point in time as a measure of benefits to customers over time. 
20 
Instead, the fact that the way transmission assets are used will change as the topology of 
21 
41
PJM Interconnection, L.L.C., 2026 PJM Load Forecast Report (Jan. 14, 2026), https://www.pjm.com/ 
/media/DotCom/library/reports-notices/load-forecast/2026-load-report.pdf.

PDF page 311

Exhibit No. PTO-0001 
Page 29 of 43 
the transmission system changes supports the need to transition the recovery of the costs 
1 
of the transmission assets to a broader base of customers. 
2 
Accordingly, I believe that 15 years represents a reasonable balance consistent with 
3 
cost-causation and beneficiary-pays principles, recognizing that the Interconnection 
4 
Reliability Reinforcements are initially driven by generation interconnection requests and 
5 
transmission service requests made by Eligible Customers on behalf of Large Loads, but 
6 
that the benefits associated with these facilities will broaden as the transmission system 
7 
changes over time. 
8 
E. 
Ratepayer Protection Mechanisms 
9 
Q. 
Does the PJM Transmission Owners’ proposal address potential cost shifts among 
10 
wholesale transmission customers? 
11 
A. 
[Hammer] Yes.  First, as discussed below, the PJM Transmission Owners proposal 
12 
includes a pro forma CRA that, along with comparable individual agreements, will ensure 
13 
that Large Load customers commit to a minimum contribution to each Transmission 
14 
Owner’s revenue requirement.42
15 
Second, each PJM Transmission Owner commits to make a compliance filing to 
16 
include in its formula rate provisions a mechanism designed to protect wholesale 
17 
transmission customers in its Zone from having to bear excessive large-load-related system 
18 
upgrade costs when they do not have service requests associated with Large Load in a 
19 
cluster.  In particular, this mechanism will protect municipal and cooperative entities that 
20 
are not regulated by states, and therefore state jurisdictional retail efforts cannot insulate 
21 
42
Proposed Tariff, Part VIII, Subpart N, section 441(a); Proposed pro forma CRA, Part IX, Subpart P at Articles 
5-7.

PDF page 312

Exhibit No. PTO-0001 
Page 30 of 43 
them from bearing a potentially disproportionate amount of costs associated with 
1 
reinforcements necessary to provide transmission service to Large Load.  The PJM 
2 
Transmission Owners have deliberately avoided specifying a single mechanism for 
3 
implementing this commitment due to the need for flexibility so that Transmission Owners 
4 
can design and propose wholesale customer protection mechanisms that are consistent with 
5 
any applicable retail allocation or charge mechanisms. 
6 
Q. 
Does the PJM Transmission Owners’ proposal address potential cost shifts among 
7 
retail customers within the same utility? 
8 
A.  
[Hammer] Consistent with the Commission’s findings in the Show Cause Order, the PJM 
9 
Transmission Owners’ proposal focuses on cost allocation and potential cost shifts at the 
10 
wholesale transmission level.  The allocation of transmission costs among retail customer 
11 
classes, including Large Load customers, is generally addressed through retail rate design 
12 
subject to state regulatory jurisdiction.  However, to facilitate the ability of state regulators 
13 
to allocate costs at the retail level and to provide the transparency desired by the 
14 
Commission as expressed in the Show Cause Order, the PJM Transmission Owners are 
15 
committing to make, on compliance, necessary changes to their formula rate templates to 
16 
include information regarding the costs of transmission facilities being constructed by the 
17 
Transmission Owner to provide transmission service to Large Loads.43  This information 
18 
is similar to information already provided by PJM Transmission Owners regarding PJM 
19 
RTEP projects subject to regional cost allocation, and recovered through the TEC.  Based 
20 
43
Proposed Schedule 12, Sections (f)(3)-(5). The Transmission Owner’s annual transmission revenue 
requirement associated with an Interconnection Reliability Reinforcement will be determined pursuant to the formula 
rate in effect applicable to the Transmission Owner’s rates for Firm Transmission Service.  Transmission Owners will 
make a compliance filing to be submitted within 120 days after the Commission issues an order accepting this filing 
to include any necessary revisions to the Transmission Owner’s formula rate template to identify each IRR.

PDF page 313

Exhibit No. PTO-0001 
Page 31 of 43 
on this information, state regulators may then determine whether and how such costs 
1 
should be assigned to Large Load customers through retail Large Load tariffs, special 
2 
contracts, riders, minimum demand or revenue requirements, or other retail rate 
3 
mechanisms. 
4 
Q. 
How would the cost allocation proposal apply to a co-located Large Load and 
5 
generation arrangement? 
6 
A. 
[Hammer] For a co-located arrangement, the proposed methodology separately evaluates 
7 
the generation interconnection request and the Large Load transmission service request.  
8 
At the same time, consistent with the Commission’s directive, the co-located generation 
9 
may reduce the amount of Firm Transmission Service required by the Large Load and, 
10 
therefore, the Large Load’s impact on the transmission system and the Interconnection 
11 
Reliability Reinforcements required to serve it. 
12 
For example, assume a co-located facility consists of a 500 MW Large Load and 
13 
400 MW of generation.  If the Large Load requests 100 MW of Firm Contract Demand 
14 
Transmission Service and the generator requests 400 MW of generator interconnection 
15 
service, the generator’s proportional impact would be evaluated based on the generation 
16 
studied through the Fast Energization Process, while the Large Load’s proportional impact 
17 
would be evaluated based on its 100 MW Firm Transmission Service request.44
18 
19 
20 
21 
44
 Proposed Schedule 12, Sections (f)(2)(A), (C).

PDF page 314

Exhibit No. PTO-0001 
Page 32 of 43 
VIII. COST RECOVERY AGREEMENT 
1 
Q. 
What concern identified by the Commission in the Show Cause Order is the proposed 
2 
Cost Recovery Agreement intended to address? 
3 
A. 
[Hammer] The Commission expressed concern that transmission costs incurred to serve a 
4 
Large Load could be shifted to other wholesale transmission customers if the Large Load 
5 
does not materialize, ramps more slowly than expected, or reduces or terminates service.45
6 
The proposed pro forma CRA addresses this risk by establishing financial protections 
7 
designed to ensure that the Large Load Customer bears an appropriate share of the financial 
8 
risk associated with its Firm Transmission Service commitment, thereby protecting other 
9 
wholesale transmission customers from potential cost shifts. 
10 
Q. 
Please provide an overview of the proposed CRA. 
11 
A. 
[Hammer] The proposed CRA is a three-party agreement among the Transmission Owner, 
12 
the Eligible Customer taking transmission service on behalf of the Large Load Customer, 
13 
and the underlying Large Load Customer designed to protect other wholesale transmission 
14 
customers from cost shifts associated with serving a Large Load.  The CRA includes a 
15 
commitment extending for a minimum of ten years after the first Service Date and several 
16 
key financial protections, including a minimum revenue commitment and associated 
17 
shortfall payment mechanism, credit support, and early and partial termination amounts 
18 
that collectively address the risk that the anticipated transmission revenues associated with 
19 
the Large Load’s Firm Transmission Service commitment will not materialize over the 
20 
45
Show Cause Order at PP 79, 83.

PDF page 315

Exhibit No. PTO-0001 
Page 33 of 43 
term of the CRA, thereby reducing the risk that the resulting revenue exposure will be 
1 
borne by other wholesale transmission customers.46
2 
The CRA initially reflects the Large Load Customer’s anticipated load demand and 
3 
ramp schedule, including the anticipated dates for each stage of service, together with the 
4 
amount and type of firm transmission service that the Eligible Customer intends to request 
5 
on the Large Load Customer’s behalf, which establish the customer’s initial commitment 
6 
before completion of PJM’s Fast Energization Process.  Following completion of PJM’s 
7 
transmission Fast Energization Process and execution of the Final PJM Agreement, the 
8 
CRA is updated to reflect the type of and amount of Firm Transmission Service, load ramp, 
9 
and Service Dates established through that process.  These amounts and dates establish the 
10 
Large Load Customer’s Firm Load Commitment, which identifies the committed load 
11 
level, corresponding level of Firm Transmission Service, and applicable load-ramp 
12 
milestones and Service Dates.  The Firm Load Commitment serves as the benchmark for 
13 
determining the Large Load Customer’s minimum transmission-revenue obligation.47
14 
Beginning on each applicable Service Date, and no more frequently than annually, 
15 
the applicable Transmission Owner calculates the minimum transmission-revenue 
16 
contribution associated with the Firm Load Commitment, referred to as the Committed 
17 
Revenue Contribution, and compares that amount against qualifying revenues attributable 
18 
to the firm transmission service actually taken to serve the Large Load, referred to as the 
19 
Actual Revenue Contribution.  If the Actual Revenue Contribution is less than the 
20 
46
Proposed pro forma CRA, Part IX, Subpart P at Preamble and Articles 4.2, 5-6, 9. 
47
Id. at Articles 3.1-3.2 and Exhibit A.

PDF page 316

Exhibit No. PTO-0001 
Page 34 of 43 
Committed Revenue Contribution for the applicable Measurement Period, the Large Load 
1 
Customer is required to pay only the difference, or Shortfall Amount.  Credit Support 
2 
secures the Large Load Customer’s payment and other financial obligations under the 
3 
CRA, including any Shortfall Amount, Early Termination Amount, or Partial Termination 
4 
Amount.48  The CRA’s early and partial termination provisions likewise protect against the 
5 
applicable portion of the remaining projected revenue commitment if the transmission 
6 
request or commitment is withdrawn, the Large Load is abandoned or terminated, or its 
7 
capacity is permanently reduced.  In the event of termination before the first Service Date, 
8 
the Transmission Owner may draw on Credit Support to satisfy the applicable termination 
9 
payment.  That payment is applied first to Project Development Costs associated with 
10 
transmission facilities that will no longer be needed to serve the Large Load, including 
11 
such costs incurred by other Transmission Owners, thereby ensuring that these costs will 
12 
not be included in transmission rate base and recovered from other customers.49
13 
Q. 
Please explain how the proposed CRA is designed to address the risk of cost shifts 
14 
among wholesale transmission customers. 
15 
A. 
[Hammer] The PJM Transmission Owners’ proposed CRA combines a minimum revenue 
16 
contribution, financial-security requirements, and flexibility to tailor specified terms to the 
17 
applicable Transmission Owner and customer parties.  That framework is intended to 
18 
provide necessary wholesale customer protections while promoting timely Large Load 
19 
integration.  Each of the CRA’s financial security requirement addresses a different aspect 
20 
48
Id. at Articles 5.1-5.5, 6.1–6.5, 7.6 and Exhibits B–C. 
49
Proposed Tariff, Part VIII, Subpart N, section 441(e); Proposed pro forma CRA, Part IX, Subpart P at 
Articles 9.1-9.12 and Exhibit D.

PDF page 317

Exhibit No. PTO-0001 
Page 35 of 43 
of wholesale transmission cost shift risk.  The minimum revenue commitment addresses 
1 
the risk that anticipated Firm Transmission Service revenues associated with serving a 
2 
Large Load do not materialize.  Credit Support provides financial assurance that the Large 
3 
Load Customer can satisfy its transmission payment obligations over the remaining term 
4 
of the CRA.  Finally, early and partial termination amounts protect against the loss of the 
5 
anticipated revenue contribution if the Large Load Customer terminates or permanently 
6 
reduces its commitment before the end of the agreed period.  Together, these protections 
7 
provide reasonable assurance that the financial risks associated with the Large Load 
8 
Customer’s Firm Transmission Service commitment are not shifted to other wholesale 
9 
transmission customers.50
10 
Q.
Please explain the minimum revenue contribution mechanism and how it protects 
11 
other wholesale transmission customers from potential cost shifts. 
12 
A. 
[Hammer] The minimum revenue contribution mechanism establishes a minimum level 
13 
of transmission revenue that the Large Load Customer is responsible for providing, through 
14 
transmission service payments made by an Eligible Customer on its behalf, during each 
15 
Measurement Period, generally one year.  The CRA establishes a Committed Revenue 
16 
Contribution based on the projected Firm Transmission Service charges associated with 
17 
the applicable load commitment, multiplied by the applicable Minimum Commitment 
18 
Percentage, which ranges from 80 to 100 percent.  For each Measurement Period, the 
19 
Transmission Owner then compares the customer’s actual contribution to the Transmission 
20 
Owner’s revenue requirement, based on its actual use, to its Committed Revenue 
21 
50
Proposed Tariff, Part VIII, Subpart N, section 441(a); Proposed pro forma CRA, Part IX, Subpart P at Articles 
5-6, 9.

PDF page 318

Exhibit No. PTO-0001 
Page 36 of 43 
Contribution.  If actual revenues fall below the committed amount, the Large Load 
1 
Customer must pay the difference as a Shortfall Amount.  The minimum revenue 
2 
contribution is initially determined at CRA execution prior to the Large Load customer 
3 
entering the PJM Fast Energization Process based on the amount of service to be requested 
4 
on behalf of the Large Load (the “Initial Load Commitment”), and then updated at the end 
5 
of the PJM Fast Energization Process based on any changes made during that process (the 
6 
“Firm Load Commitment”).51
7 
This mechanism mitigates potential cost shifts by ensuring that the Large Load 
8 
Customer provides a minimum level of revenue associated with its Firm Transmission 
9 
Service commitment, even if its load does not materialize or ramp as expected.  At the 
10 
same time, revenues attributable to serving the Large Load are counted against that 
11 
commitment, so the Shortfall Amount reflects only the difference needed to satisfy the 
12 
agreed minimum contribution.  Shortfall Amounts are credited against the Transmission 
13 
Owner’s transmission revenue requirement, thereby reducing the costs that otherwise could 
14 
be recovered from other wholesale transmission customers.52
15 
Q.
Why is the proposed Minimum Commitment Percentage range of 80 to 100 percent 
16 
reasonable? 
17 
A. 
[Hammer] In my opinion, the proposed range is reasonable because it establishes a 
18 
meaningful minimum revenue commitment while allowing individual Transmission 
19 
Owners to require a higher commitment where appropriate based on their particular 
20 
51
Proposed pro forma CRA, Part IX, Subpart P at Articles 3.1-3.2, 5.1-5.5 and Exhibits A-B. 
52
Id. at Article 7.6.

PDF page 319

Exhibit No. PTO-0001 
Page 37 of 43 
circumstances.  The 80 percent floor is also consistent with prior agreements accepted by 
1 
the Commission.53
2 
Q.
How is the Credit Support Requirement determined? 
3 
A. 
[Hammer] The Credit Support Requirement is designed to secure the Transmission 
4 
Owner’s projected Firm Transmission Service revenue exposure associated with the Large 
5 
Load Customer’s commitment over the remaining term of the CRA.  It equals the aggregate 
6 
Projected Full Firm Transmission Service Benchmarks for the Measurement Periods 
7 
remaining in the Term, including any incomplete portion of the applicable Measurement 
8 
Period.  Initially, it is based on 100 percent of the projected Firm Transmission Service-
9 
related charges associated with the Initial Load Commitment over the CRA term.  
10 
Following completion of the PJM Fast Energization Process and execution of the relevant 
11 
service agreement with PJM (referred to in the filing as the “Final PJM Agreement”), that 
12 
amount is recalculated based on the Firm Load Commitment, Service Dates, and other 
13 
information established following the Final PJM Agreement.  The Credit Support 
14 
Requirement is then recalculated after each Measurement Period.  Once the Large Load 
15 
Customer has satisfied its obligations for a Measurement Period, that period is removed 
16 
from the calculation.  As a result, the Credit Support Requirement generally declines as 
17 
completed Measurement Periods are reconciled, paid, and removed from the calculation, 
18 
although it may also be adjusted when other relevant inputs change.54
19 
20 
53
See Commonwealth Edison Co., 194 FERC ¶ 61,109 (2026); Commonwealth Edison Co., 194 FERC ¶ 61,185 
(2026); PECO Energy Co., 193 FERC ¶ 61,148 (2025). 
54
Proposed pro forma CRA, Part IX, Subpart P at Articles 6.1, 6.5 and Exhibit C.

PDF page 320

Exhibit No. PTO-0001 
Page 38 of 43 
Q.
How is the Projected Full Firm Transmission Service Benchmark determined?
1 
A. 
[Hammer] The Projected Full Firm Transmission Service Benchmark represents the 
2 
projected charges for 100 percent of the Large Load Customer’s applicable Firm 
3 
Transmission Service for each Measurement Period.  For each Measurement Period 
4 
included in the Credit Support Requirement, the Projected Full Firm Transmission Service 
5 
Benchmark equals the Firm Transmission Service-related charges that would apply if 
6 
Eligible Customer took Firm Transmission Service corresponding to the Initial Load 
7 
Commitment or Firm Load Commitment, as applicable, scheduled to apply during that 
8 
Measurement Period.  It is calculated using the customer’s Firm Load Commitment, the 
9 
applicable Firm Transmission Service rates, and the portion of the Measurement Period 
10 
during which those load levels and rates apply.  The calculation also reflects any rate 
11 
change accepted by the Commission and scheduled to become effective during the 
12 
applicable Measurement Period.55
13 
Q. 
Why is the Credit Support Requirement adjusted over the life of the CRA, and why 
14 
is that approach reasonable? 
15 
A. 
[Hammer] The Credit Support Requirement is adjusted over the life of the CRA so that 
16 
the amount of financial security continues to reflect the Transmission Owner’s full 
17 
projected Firm Transmission Service revenue exposure over the remaining term of the 
18 
CRA.  After each Measurement Period is finally reconciled and the Large Load Customer 
19 
has paid all amounts due for that period, that Measurement Period is removed from the 
20 
Credit Support Requirement.  The requirement is also recalculated when relevant inputs 
21 
55
Id. at Exhibit C, Sections 1-3.

PDF page 321

Exhibit No. PTO-0001 
Page 39 of 43 
change, such as the Firm Load Commitment, Service Dates, or applicable Firm 
1 
Transmission Service rates.56
2 
This approach is reasonable because it appropriately aligns the amount of financial 
3 
security with the exposure that remains under the CRA.  The Transmission Owner, to the 
4 
benefit of other customers, retains financial assurance for its full projected exposure over 
5 
the remaining term, while the Large Load Customer receives the benefit of a reduction in 
6 
Credit Support as it satisfies its obligations over time.  Once a Measurement Period has 
7 
been completed, reconciled, and paid, there is no longer a need to include that period in the 
8 
amount being secured.  The result is a Credit Support Requirement that remains sufficient 
9 
to protect against prospective revenue risk without requiring the Large Load Customer to 
10 
collateralize exposure that has already been eliminated through performance.  
11 
Q.
What are the early and partial termination provisions?
12 
A. 
[Hammer] The early and partial termination provisions address circumstances in which 
13 
the Firm Transmission Service request is: (i) withdrawn or abandoned, (ii) the CRA 
14 
terminates before the end of its agreed term, (iii) the project is abandoned or ceases 
15 
operations, or (iv) the Large Load Customer permanently reduces its Firm Load 
16 
Commitment.  In those circumstances, the Large Load Customer is responsible for an Early 
17 
Termination Amount or Partial Termination Amount.  The Early Termination Amount 
18 
protects a specified portion of the revenue contribution projected for the remainder of the 
19 
CRA and is generally based on the applicable Termination Percentage and the present value 
20 
of the remaining Projected Committed Revenue Contributions, less applicable credits.  For 
21 
56
Id. at Article 6.5 and Exhibit C, Sections 1-4.

PDF page 322

Exhibit No. PTO-0001 
Page 40 of 43 
a partial termination, the amount is adjusted to reflect the permanent reduction in the Large 
1 
Load Customer’s Firm Load Commitment.57
2 
Q.
Why are these termination provisions necessary?
3 
A.  
[Hammer] These termination provisions are necessary because the Transmission Owner 
4 
may make long-term transmission planning and investment decisions based on the Large 
5 
Load Customer’s Firm Load Commitment.  If the customer terminates or materially 
6 
reduces that commitment, the associated transmission revenues may no longer materialize. 
7 
The termination provisions mitigate that risk by assigning an appropriate portion of the 
8 
remaining revenue exposure to the Large Load Customer whose project and Firm Load 
9 
Commitment gave rise to the exposure, thereby reducing the potential for the resulting 
10 
revenue shortfall to be shifted to other wholesale transmission customers. 
11 
Q.
How are the Early Termination Amount and Partial Termination Amount 
12 
determined? 
13 
A. 
[Hammer] The Early Termination Amount is generally calculated by applying the 
14 
applicable Termination Percentage to the present value of the remaining Projected 
15 
Committed Revenue Contributions, less any applicable credits. The Termination 
16 
Percentage increases as the project progresses, from 25 percent before execution of the 
17 
Final PJM Agreement, to 50 percent during the first 180 days following execution of the 
18 
Final PJM Agreement, to 75 percent thereafter and before the first Service Date, and to 100 
19 
percent on and after the first Service Date.58  The present value calculation reflects the 
20 
57
Id. at Articles 9.1-9.9 and Exhibit D. 
58
Id. at Exhibit D, Section 1.

PDF page 323

Exhibit No. PTO-0001 
Page 41 of 43 
Large Load Customer’s remaining Firm Load Commitment, the Minimum Commitment 
1 
Percentage, applicable transmission service rates, rate components and billing 
2 
determinants identified in Exhibit B to the CRA, and the Transmission Owner’s then-
3 
effective FERC-approved Weighted Average Cost of Capital as the discount rate.  
4 
The Partial Termination Amount applies the same framework to the portion of the 
5 
Firm Load Commitment that is permanently reduced. Generally, it is determined by 
6 
multiplying the Early Termination Amount by the percentage of committed MW being 
7 
reduced.59
8 
Q.
How are the Termination Percentages determined and why are they reasonable?
9 
A. 
[Hammer] The Termination Percentages increase as the project progresses, reflecting the 
10 
increasing financial exposure associated with the Large Load Customer’s commitment.  
11 
Under the CRA, the applicable percentage increases from 25 percent prior to execution of 
12 
the Final PJM Agreement to 100 percent on and after the first Service Date.60
13 
This approach is reasonable because it aligns the customer’s termination 
14 
responsibility with the stage of its commitment and the Transmission Owner’s increasing 
15 
exposure as the project advances.  At earlier stages, when the project is less advanced and 
16 
the Transmission Owner’s exposure is correspondingly lower, only a portion of the 
17 
remaining committed revenue exposure is assigned to the Large Load Customer.  As the 
18 
project advances and the Transmission Owner increasingly relies on the Firm Load 
19 
Commitment for planning, investment, and anticipated revenue recovery, the Large Load 
20 
59
Id. at Articles 9.7-9.9 and Exhibit D, Sections 1-5. 
60
Id. at Exhibit D, Section 1.

PDF page 324

Exhibit No. PTO-0001 
Page 42 of 43 
Customer assumes a greater share of that exposure.  Once service begins, the Large Load 
1 
Customer is responsible for 100 percent of its remaining committed revenue obligation in 
2 
the event of termination.  
3 
Q.
Why is the Termination Amount based on the minimum revenue obligation rather 
4 
than projected full transmission revenues, as used to calculate the Credit Support 
5 
Requirement? 
6 
A. 
[Hammer] The Termination Amount represents an actual payment obligation, whereas the 
7 
Credit Support Requirement represents financial security for potential exposure.  Because 
8 
the Large Load Customer’s contractual minimum revenue obligation is determined by 
9 
applying the Minimum Commitment Percentage to projected transmission revenues, it is 
10 
reasonable for the Termination Amount to be based on that committed revenue obligation 
11 
rather than 100 percent of projected revenues.  This distinction ensures that the more 
12 
conservative Credit Support Requirement provides financial assurance against potential 
13 
exposure without converting that higher level of security into a greater payment obligation 
14 
upon termination. 
15 
Thus, the two provisions serve different but complementary purposes: Credit 
16 
Support secures the Transmission Owner’s full projected exposure, while the Termination 
17 
Amount reflects the Large Load Customer’s contractual payment responsibility upon 
18 
termination.61
19 
61
Id. at Exhibit C, Sections 1-3, 7 and Exhibit D, Sections 2-3.

PDF page 325

Exhibit No. PTO-0001 
Page 43 of 43 
Q.
In your opinion, does the proposed CRA provide an appropriate framework for 
1 
mitigating potential cost shifts associated with Large Loads among wholesale 
2 
transmission customers? 
3 
A. 
[Hammer] Yes. The proposed CRA provides an appropriate set of financial protections 
4 
designed to mitigate the risk that costs associated with serving a Large Load will be shifted 
5 
to other wholesale transmission customers.  It achieves this through a set of  interlocking 
6 
mechanisms. 
7 
The proposed CRA establishes a minimum revenue commitment to provide a 
8 
defined level of transmission revenue even if the Large Load does not materialize or ramp 
9 
as expected. It requires Credit Support based on 100 percent of projected Firm 
10 
Transmission Service revenues, providing a strong financial backstop for the Transmission 
11 
Owner’s potential exposure.  And, if the customer terminates or reduces its commitment, 
12 
the early and partial termination provisions require the customer to bear an appropriate 
13 
portion of its remaining committed revenue obligation.62
14 
Collectively, these provisions appropriately allocate the financial risks associated 
15 
with the Large Load Customer’s Firm Transmission Service commitment to that customer, 
16 
while calibrating the customer’s payment and Credit Support obligations to the nature and 
17 
extent of the exposure being addressed. 
18 
Q. 
Does this complete your testimony at this time? 
19 
A. 
[Blazunas and Hammer] Yes.
20 
62
Id. at Articles 5-6, 9 and Exhibits B-D.

PDF page 326

UNITED STATES OT' AMERIC.A.
BEFORE THE
FEDERAL ENERGY RBGULATORY COMMISSIOI\
lrxelotr Corporatiofi, et ill.
)
[-]ockct No. Ir,l{27-, ---00t)
DECLARATION OF PETER BLAZUNAS
I depose and state under penalty of perjury that the_ foregoing exhibits were prepared or
assembled by me or under my direction, and that I have read the foregoing questions and answers
labeled as my testimony: ttrat if asked the same questions my answffs in response would be as
shown; and that the facts contained in my answers are true to the best of my knowledge,
infirrrnati r-rn" and heli ef -
November 16. 2()26

PDF page 327

UNITED STATES OF AMERICA 
BEFORE THE 
FEDERAL ENERGY REGULATORY COMMISSION 
 
Exelon Corporation, et al.  
 
 
)  
 
Docket No. ER27-___-000 
 
 
DECLARATION OF HANHAN HAMMER 
 
 
I depose and state under penalty of perjury that the foregoing exhibits were prepared or 
assembled by me or under my direction, and that I have read the foregoing questions and answers 
labeled as my testimony: that if asked the same questions my answers in response would be as 
shown; and that the facts contained in my answers are true to the best of my knowledge, 
information, and belief. 
 
 
 
 
 
 
 
 
                                                       
 
 
 
 
 
 
 
 
______________________ 
 
 
 
 
 
 
 
Hanhan Hammer 
 
November 16, 2026

PDF page 328

RESUMES OF PETER BLAZUNAS AND HANHAN HAMMER 
 
 
 
 
  CONCENTRIC ENERGY ADVISORS 
PETER BLAZUNAS 
VICE PRESIDENT 
PROFESSIONAL HISTORY 
Concentric Energy Advisors, Inc.  
Vice President (January 2026 – Present) 
Assistant Vice President (January 2024 – December 2025) 
Senior Project Manager (January 2023 - December 2023) 
Project Manager (October 2021 - December 2022)  
 
Currently serve as the project manager and expert witness for a long-term staff augmentation 
engagement with Narragansett Electric Company (“NECO”, also known as Rhode Island 
Energy) following its acquisition by PPL from National Grid. Staff augmentation services 
include the provision of expert witness testimony and analyst support in the litigation of gas 
and electric rate mechanism proceedings, the execution of both internal and external monthly 
reporting, the development of written processes and procedures, and the training of new 
personnel.  
 
Executes projects and initiatives related to cost of service and rate design and, where 
appropriate, serves as an expert witness in regulatory proceedings. 
 
A recent engagement included the provision of expert witness testimony with respect to rate 
design in a multi-year rate plan application for an electric utility in Maryland.  
 
Manages all phases of assigned projects with teams of senior staff and supporting analysts 
across multiple offices. 
Mr. Blazunas specializes in regulatory strategy and rate case expertise for regulated electric 
and gas utility rate proceedings. He joined Concentric in 2021 after nine years in progressively 
senior roles within the regulatory departments of large investor-owned electric utilities. Most 
recently, at Exelon Corp., he managed a team overseeing cost of service, revenue allocation, 
rate design, revenue decoupling, and rate administration for Pepco’s Maryland and District of 
Columbia jurisdictions. At Concentric, Peter Blazunas has led diverse projects, including staff 
augmentation for a New England gas and electric utility’s pricing team, assisting in the 
development of the revenue requirement and minimum filing requirements for the multiyear 
rate plan application of a large Midwestern electric utility, and testifying on rate design and 
revenue decoupling for mid-Atlantic electric utilities in multiyear rate plan applications. He is a 
seasoned expert witness, having testified in traditional base distribution rate cases and 
multiyear rate plan proceedings before regulatory commissions in Delaware, the District of 
Columbia, Maryland, Ohio, and Rhode Island. Mr.  Blazunas has also testified before the Federal 
Energy Regulatory Commission. Mr. Blazunas earned a B.A. and M.A. in Economics from the 
University of Dayton and the University of Akron, respectively. He has also taught undergraduate 
and graduate economics at the University of Akron and Cuyahoga Community College. 
Exhibit No. PTO-0002
Page 1 of 8

PDF page 329

RESUMES OF PETER BLAZUNAS AND HANHAN HAMMER 
 
 CONCENTRIC ENERGY ADVISORS 
Pepco (Exelon Corp.), Washington, D.C.  
Manager of Rate Administration (November 2018 – January 2021) 
Senior Rate Analyst (July 2017 – November 2018) 
 
Managed a team of four rate analysts responsible for the cost of service and rate design 
functions with respect to Pepco’s base distribution rates.  
 
Served as the rate design witness for Pepco’s Maryland and District of Columbia base 
distribution rate case and multi-year rate plan proceedings, with a focus on revenue allocation, 
rate design, and decoupling in both traditional and non-traditional contexts.  
 
Served as the rate design and cost recovery witness for several of Exelon’s Pepco Holdings Inc. 
(“PHI") jurisdictions with respect to transportation electrification.  
 
Oversaw the development of self-contained cost-of-service (“COS”) and rate design Microsoft 
Excel models for use in regulatory proceedings.  
 
Guided the creation of concise and well-written processes and procedures as it relates to the 
development of base distribution rates, numerous distribution riders, and transmission retail 
rates.  
 
Directed the development of internal project plan templates for use in executing initiatives 
related to the implementation of traditional and innovative rates.  
 
Supervised the development of internal documents to direct Pepco’s policy positions on a range 
of issues in work group settings with a diverse set of external stakeholders (primarily, the 
Maryland Public Service Commission Public Conference 44 Rate Design Working Group and the 
District of Columbia Public Service Commission Rate Design Working Group). 
First Energy Corp., Akron, OH  
State Regulatory Analyst (January 2012 – June 2017) 
 
Served as the lead analyst for the FirstEnergy Ohio operating companies’ Delivery Capital 
Recovery Rider (“Rider DCR”). Duties included the preparation of a detailed quarterly filing 
with the Public Utilities Commission of Ohio (“PUCO”) that requires complex revenue 
requirement calculations, extensive intra-company communication and collaboration in the 
development of financial inputs, month-to-month analysis, and participation in an annual audit 
conducted by an outside consultant on behalf of the PUCO.  
 
Duties also included (a) the role of Rates and Regulatory Affairs Department point of contact 
for internal customers in relation to the application of The Cleveland Electric Illuminating 
Company’s and The Toledo Edison Company’s tariffs and (b) participation in various state 
regulatory proceedings, including testifying in front of the PUCO. 
Cuyahoga Community College, Highland Hills, OH 
Adjunct Faculty (Hybrid) (January 2022 – May 2022) 
 
Courses Taught: Principles of Microeconomics (Undergraduate) 
University of Akron, Akron, OH 
Assistant Lecturer (In-Person) (September 2023 – Present) 
Exhibit No. PTO-0002
Page 2 of 8

PDF page 330

RESUMES OF PETER BLAZUNAS AND HANHAN HAMMER 
 
 CONCENTRIC ENERGY ADVISORS 
 
Courses Taught: Introduction to Economic Analysis (Undergraduate); Economic Decision 
Making for Business (Graduate); Regulatory Economics (Undergraduate/Graduate) 
Associate Lecturer (Online) (January 2018 – May 2018) 
 
Courses Taught: Survey of Basic Economics (Undergraduate) 
Associate Lecturer (In-Person) (August 2012 – May 2017) 
 
Courses Taught: Principles of Microeconomics and Principles of Macroeconomics 
(Undergraduate) 
EDUCATION 
University of Akron (Akron, Ohio), December 2011 
Master of Arts, Economics  
University of Dayton (Dayton, Ohio), May 2009 
Bachelor of Arts, Economics, Summa Cum Laude 
CONTINUED EDUCATION 
Utility Accounting and Finance Seminar, January 2018 
Financial Accounting Institute, Washington, D.C. 
Morgan Stanley Investment Banking Client Training Program, April 2016 
Training the Street, New York City, NY 
Edison Electric Institute Advanced Ratemaking Course, August 2013 
Edison Electric Institute, Madison, WI 
 
Exhibit No. PTO-0002
Page 3 of 8

PDF page 331

RESUMES OF PETER BLAZUNAS AND HANHAN HAMMER 
 
CONCENTRIC ENERGY ADVISORS 
SPONSOR  
DATE  
CASE/APPLICANT  
DOCKET  
SUBJECT 
Federal Energy Regulatory Commission 
PJM Transmission Owners 
2026 
PJM Transmission 
Owners 
Docket No. 
EL25-49 
Rate Design  
Delaware Public Service Commission 
Delmarva Power and Light 
Company 
2018
Delmarva Power 
and Light Company 
Docket No. 
17-1094 
Rate Design and Cost Recovery 
(Transportation 
Electrification) 
Public Service Commission of the District of Columbia 
Potomac Electric Power 
Company  
2019 
Potomac Electric 
Power Company 
Formal Case 
No. 1156 
Rate Design (Multi-Year Rate 
Plan) 
Potomac Electric Power 
Company 
2019 
Potomac Electric 
Power Company 
Formal Case 
No. 
1145/1159 
Rate Design and Cost Recovery 
(Undergrounding Application) 
Potomac Electric Power 
Company 
2018
Potomac Electric 
Power Company 
Formal Case 
No. 1130 
Rate Design and Cost Recovery 
(Transportation 
Electrification) 
Maryland Public Service Commission 
Potomac Electric Power 
Company 
2025 
Potomac Electric 
Power Company 
Case No. 9820 
Rate Design (Fully Forecasted 
Test Year) 
Potomac Electric Power 
Company 
2023 
Potomac Electric 
Power Company 
Case No. 9702 
Rate Design (Multi-Year Rate 
Plan) 
Delmarva Power and Light 
Company 
2022 
Delmarva Power 
and Light Company 
Case No. 9681 
Rate Design (Multi-Year Rate 
Plan) 
Potomac Electric Power 
Company  
2020 
Potomac Electric 
Power Company 
Case No. 9655 
Rate Design (Multi-Year Rate 
Plan) 
Potomac Electric Power 
Company  
2019 
Potomac Electric 
Power Company 
Case No. 9602 
Rate Design (Traditional Rate 
Case) 
Potomac Electric Power 
Company  
2018 
Potomac Electric 
Power Company 
Case No. 9472 
Rate Design (Traditional Rate 
Case) 
Public Utilities Commission of Ohio
The Cleveland Electric 
Illuminating Company  
2017
The Cleveland 
Electric Illuminating 
Company 
Case No. 16-
2213-EL-CSS 
Customer Complaint Case
The Toledo Edison Company
2014
The Toledo Edison 
Company 
Case No. 13-
2145-EL-CSS 
Customer Complaint Case
Rhode Island Public Utilities Commission 
Rhode Island Energy 
2025 
Rhode Island 
Energy 
Docket No. 
25-45-GE 
Rate Design (General Rate 
Case) 
Rhode Island Energy
2025
Rhode Island 
Energy 
Docket No. 
25-23-REG 
Rate Design and Cost Recovery 
(Renewable Energy Program) 
Rhode Island Energy 
2025 
Rhode Island 
Energy 
Docket No. 
25-04-REG 
Rate Design and Cost Recovery 
(Annual Retail Rate Filing) 
Rhode Island Energy
2024
Rhode Island 
Energy 
Docket No. 
24-48-REG 
Rate Design and Cost Recovery 
(Renewable Energy Program) 
Rhode Island Energy
2024
Rhode Island 
Energy 
Docket No. 
24-29-NG 
Rate Design and Cost Recovery 
(Distribution Adjustment 
Charge and Gas Cost Recovery) 
Rhode Island Energy
2024
Rhode Island 
Energy 
Docket No. 
23-45-EL 
Rate Design and Cost Recovery 
(Renewable Resource Rider) 
Exhibit No. PTO-0002
Page 4 of 8

PDF page 332

RESUMES OF PETER BLAZUNAS AND HANHAN HAMMER 
 
CONCENTRIC ENERGY ADVISORS 
SPONSOR  
DATE  
CASE/APPLICANT  
DOCKET  
SUBJECT 
Rhode Island Energy
2024
Rhode Island 
Energy 
Docket No. 
24-18-EL 
Rate Design and Cost Recovery 
(Electric Revenue Decoupling 
Mechanism) 
Rhode Island Energy
2024
Rhode Island 
Energy 
Docket No. 
24-17-EL 
Rate Design and Cost Recovery
(Residential Assistance 
Recovery Filing) 
Rhode Island Energy 
2024 
Rhode Island 
Energy 
Docket No. 
24-07-EL 
Rate Design and Cost Recovery 
(Annual Retail Rate Filing) 
Rhode Island Energy
2023
Rhode Island 
Energy 
Docket No. 
23-05-EL 
Tariff Advice (Net Metering)
Rhode Island Energy 
2023 
Rhode Island 
Energy 
Docket No. 
23-23-NG 
Rate Design and Cost Recovery 
(Distribution Adjustment 
Charge and Gas Cost Recovery) 
Rhode Island Energy 
2023 
Rhode Island 
Energy 
Docket No. 
23-24-REG 
Rate Design and Cost Recovery 
(Renewable Energy Program) 
Rhode Island Energy 
2023 
Rhode Island 
Energy 
Docket No. 
23-03-EL 
Rate Design and Cost Recovery 
(Annual Retail Rate Filing) 
Rhode Island Energy 
2022
Rhode Island 
Energy 
Docket No. 
22-04-REG 
Rate Design and Cost Recovery 
(Renewable Energy Program) 
Rhode Island Energy 
2022 
Rhode Island 
Energy 
Docket No. 
22-13-NG 
Rate Design and Cost Recovery 
(Distribution Adjustment 
Charge) 
Rhode Island Energy 
2022 
Rhode Island 
Energy 
Docket No. 
5098 
Rate Design (Rider 
Reconciliation) 
Rhode Island Energy
2022
Rhode Island 
Energy 
Docket No. 
22-20-NG 
Rate Design and Cost Recovery 
(Gas Cost Recovery) 
Rhode Island Energy 
2022 
Rhode Island 
Energy 
Docket No. 
22-54-NG 
Rate Design and Cost Recovery 
(Infrastructure, Safety, and 
Reliability Program) 
Rhode Island Energy
2022
Rhode Island 
Energy 
Docket No. 
22-53-EL 
Rate Design and Cost Recovery 
(Infrastructure, Safety, and 
Reliability Program) 
 
 
Exhibit No. PTO-0002
Page 5 of 8

PDF page 333

RESUMES OF PETER BLAZUNAS AND HANHAN HAMMER 
 
CONCENTRIC ENERGY ADVISORS 
HANHAN HAMMER 
SENIOR PROJECT MANAGER 
EXPERTISE & KEY SKILLS 
 
Energy Industry Expertise – 17+ years of experience in ISO/RTO markets and stakeholder 
process, utility regulation, transmission ratemaking, wholesale and retail tariff design, 
market revenue forecasting, resource and transmission planning, and regulatory compliance. 
 
Regulatory Strategy & Testimony – Extensive experience preparing tariff filings, provided 
expert witness testimony, and advising clients through FERC and state regulatory 
proceedings. 
 
Wholesale Power Markets – Led design of market rules for DERs, energy storage, and 
ancillary services; skilled in market power analysis, revenue forecasting, and locational 
marginal price formation. 
 
Strategic Communication – Effective at translating complex regulatory and technical issues 
into clear insights for executives, regulators, policymakers, and industry forums. 
 
Project & Team Leadership – Strong record of managing cross-functional teams, guiding 
complex initiatives under fixed budgets, and delivering results. Directed cross-functional 
project teams, ensuring projects were completed on scope, budget, and schedule; presented 
findings to executives and regulators to support high-stakes decision-making. 
PROFESSIONAL HISTORY 
Concentric Energy Advisors (2024 – Present) 
Senior Project Manager 
 
Shaped client regulatory strategy by supporting filings and expert testimony on large load 
tariffs, transmission ratemaking, ancillary service rates in merger cases, and market power 
analyses, directly informing multimillion-dollar business decisions. 
 
Advised utilities and developers on compliance and opportunity capture under evolving 
federal and state rules (e.g., Order 2222, transmission–distribution coordination, data center 
interconnection/colocation), enabling clients to position early for regulatory and market 
advantages. 
Ms. Hammer is a recognized expert in the energy industry with over 17 years of experience in 
utility regulation and ISO/RTO operation, planning, and markets. At Concentric, she advises 
utilities, developers, grid operators, and regulators on complex regulatory, commercial, and 
market issues, including large load tariffs, transmission ratemaking and cost allocation, resource 
and transmission planning, compliance with FERC orders, and wholesale market strategies.  Ms. 
Hammer has provided expert testimony before the Federal Energy Regulatory Commission and 
New Hampshire Public Utilities Commission. Her work has helped clients secure critical 
regulatory approvals, optimize capital investments, and unlock new revenue opportunities.  
Exhibit No. PTO-0002
Page 6 of 8

PDF page 334

RESUMES OF PETER BLAZUNAS AND HANHAN HAMMER 
 
CONCENTRIC ENERGY ADVISORS 
 
Delivered market and revenue analyses that optimized generation and storage investment 
decisions, improving projected returns and clarifying participation strategies across 
wholesale and retail programs. 
 
Recommended ISO market design enhancements that incentivized preferred generation 
resources, influencing stakeholder discussions and policy direction. 
ISO New England (2014-2024) 
Principal/Lead Analyst 
 
Designed wholesale market rules enabling DERs, storage, and renewables to participate; 
developed ancillary service products and reliability solutions. 
 
Prepared tariff filings, provided expert testimony, and presented initiatives to regulators, 
legislators, and stakeholders. 
 
Advised project teams and senior management on policy trends and market design 
opportunities. 
Southwest Power Pool (2011-2014) 
Senior Market Analyst 
 
Evaluated nodal pricing and transmission congestion to support power trading hubs; 
authored State of the Market reports and presented to stakeholders and FERC. 
 
Developed analytic dashboards to monitor market performance, identify trends, and brief 
executives and boards. 
Potomac Economics (2009-2011) 
Senior Market Monitor  
 
Monitored the Midcontinent ISO (MISO) wholesale markets to detect anti-competitive 
behavior; prepared FERC referrals and supported regulatory enforcement. 
 
Advised investor-owned utilities on operational efficiency and market performance to inform 
strategic decisions. 
EDUCATION 
University of Arkansas 
Master of Business Administration  
Western Illinois University 
Master of Art in Economics  
Anhui University of Technology 
Bachler of Art in Economics and International Trade 
Exhibit No. PTO-0002
Page 7 of 8

PDF page 335

RESUMES OF PETER BLAZUNAS AND HANHAN HAMMER 
 
CONCENTRIC ENERGY ADVISORS 
SPONSOR
DATE
CASE/APPLICANT
DOCKET NO.
SUBJECT
Federal Energy Regulatory Commission
ISO New England 
Inc. and New 
England Power 
Pool 
2016 
ISO New England Inc. 
and New England 
Power Pool 
ER16-1838-000 
Real-Time Energy 
Market and Real-
Time reserves 
ISO New England 
Inc. 
2016 
ISO New England Inc. 
ER17-680-000 
Net Commitment 
Period 
Compensation 
(“NCPC”) credit 
rules 
ISO New England 
Inc. and New 
England Power 
Pool 
2017 
ISO New England Inc. 
and New England 
Power Pool 
ER17-1706-000 
Market Rule 1 
Revisions to Permit 
Use of Five-Minute 
Revenue Quality 
Meter Data in 
Energy Market 
Settlement 
ISO New England 
Inc. and New 
England Power 
Pool 
2018 
ISO New England Inc. 
and New England 
Power Pool 
ER18-897-000 
The designation and 
settlement of 
Operating Reserves 
in the Real-Time 
Energy Market 
PJM Transmission 
Owners 
2026 
PJM Transmission 
Owners 
EL25-49 
Large load co-
location 
arrangement in PJM 
Superior Court of the State of California County of Los Angeles
Los Angeles 
Department of 
Water and Power 
(“LADWP”) 
2025 
Class Counsel Kabateck 
LLP 
Lead Case No., 
BC577267 
LADWP key 
performance 
Indicators 
compliance 
New Hampshire Public Utilities Commission
Liberty Utilities 
(Granite State 
Electric) 
2026 
Liberty Utilities 
(Granite State Electric) 
DE 25-030 
Default Service 
Solicitation 
 
Exhibit No. PTO-0002
Page 8 of 8

PDF page 336

Exhibit No. PTO-0003
Page 1 of 1
(I) PJM Zonal 15-Year Annualized Peak Load Growth Rates
(a)
(b)
(c)
Zone
Summer
Winter
(1)
   
AE
0.5%
1.0%
(2)
   
BGE
0.5%
0.7%
(3)
   
DPL
0.3%
0.2%
(4)
   
JCPL
1.4%
2.2%
(5)
   
METED
1.7%
1.8%
(6)
   
PECO
1.5%
1.9%
(7)
   
PENLC
0.4%
0.4%
(8)
   
PEPCO
1.7%
1.8%
(9)
   
PL
4.4%
4.4%
(10)
 
PS
2.1%
3.1%
(11)
 
RECO
0.4%
1.2%
(12)
 
UGI
0.2%
0.1%
(13)
 
AEP
4.1%
4.4%
(14)
 
APS
2.3%
2.2%
(15)
 
ATSI
1.4%
1.8%
(16)
 
COMED
2.6%
3.8%
(17)
 
DAYTON
3.6%
3.9%
(18)
 
DEOK
0.8%
0.8%
(19)
 
DLCO
0.8%
1.0%
(20)
 
EKPC
0.6%
0.3%
(21)
 
DOM
4.9%
4.7%
(22)
 
PJM RTO
2.9%
3.3%
(23)
 
Minimum
0.2%
0.1%
(24)
 
Maximum
4.9%
4.7%
(25)
 
Minimum
UGI
UGI
(26)
 
Maximum
DOM
DOM
Source: Pages 9 and 14-34 of 2026 PJM Load Forecast Report  (January 14, 2026).
(II) PJM: Existing Capacity by Zone (MW)
(a)
(b)
(c)
(d) = (c) - (b)
(e) = (d) ÷ (b)
Zone
2011
Q3 2026
Difference
% Difference
(1)
   
AE
1,990
                            
1,274
                            
(716)
                             
-36.0%
(2)
   
BGE
5,554
                            
4,288
                            
(1,266)
                           
-22.8%
(3)
   
DPL
4,819
                            
5,038
                            
219
                               
4.5%
(4)
   
JCPL
3,980
                            
3,629
                            
(351)
                             
-8.8%
(5)
   
METED
4,167
                            
3,650
                            
(517)
                             
-12.4%
(6)
   
OVEC
-
                                
2,389
                            
2,389
                            
-
(7)
   
PECO
11,743
                          
11,978
                          
235
                               
2.0%
(8)
   
PENLC
8,366
                            
9,665
                            
1,299
                            
15.5%
(9)
   
PEPCO
6,248
                            
4,025
                            
(2,223)
                           
-35.6%
(10)
 
PL
11,274
                          
14,590
                          
3,316
                            
29.4%
(11)
 
PS
11,534
                          
9,118
                            
(2,416)
                           
-20.9%
(12)
 
AEP
34,938
                          
38,844
                          
3,906
                            
11.2%
(13)
 
APS
11,702
                          
11,109
                          
(593)
                             
-5.1%
(14)
 
ATSI
12,530
                          
10,645
                          
(1,885)
                           
-15.0%
(15)
 
COMED
28,183
                          
30,464
                          
2,281
                            
8.1%
(16)
 
DAYTON
5,785
                            
1,674
                            
(4,111)
                           
-71.1%
(17)
 
DEOK
-
                                
2,892
                            
2,892
                            
-
(18)
 
DLCO
3,286
                            
2,173
                            
(1,113)
                           
-33.9%
(19)
 
EKPC
-
                                
2,802
                            
2,802
                            
-
(20)
 
DOM
23,383
                          
32,241
                          
8,858
                            
37.9%
(21)
 
External
8,943
                            
3,241
                            
(5,702)
                           
-63.8%
(22)
 
PJM RTO
198,425
                        
205,730
                        
7,305
                            
3.7%
(23)
 
Minimum
1,990
                            
1,274
                            
(5,702)
                           
-71.1%
(24)
 
Maximum
34,938
                          
38,844
                          
8,858
                            
37.9%
(25)
 
Minimum
AE
AE
External
DAYTON
(26)
 
Maximum
AEP
AEP
DOM
DOM
Sources:
(b) See the 2011 State of the Market Report for PJM , Table 11-8 (March 15, 2012).
(c)
See the 2026 Quarterly State of the Market Report for PJM: January through September , Table 12-1 (November 12, 2026).